Confidential: FUJIFILM Service Center Use Only

X-Pro1 Service Manual

X-Pro1

CAUTION
 BECAUSE THIS PRODUCTIS RoHS LEAD-FREE COMPLIANT, USE THE DESIGNATED
AFTER-SELES PARTS AND THE DESIGNATED LEAD-FREE SOLDER WHEN
PERFORMING REPAIRS. (Refer to page 3)

WARNING
 THE COMPONENTS IDENTIFIED WITH THE MARK " " ON THE SCHEMATIC
DIAGRAM AND IN THE PARTS LIST ARE CRITICAL FOR SAFETY.
 PLEASE REPLACE ONLY WITH THE COMPONENTS SPECIFIED ON THE SCHEMATIC
DIAGRAM AND IN THE PARTS LIST.
 IF YOU USE PARTS NOT SPECIFIED, IT MAY RESULT IN A FIRE AND AN ELECTRICAL
SHOCK.

Ref. No.: ZM00984-109

Revised on 17 Oct 2013
1
 Confidential: FUJIFILM Service Center Use Only

X-Pro1 Service Manual

SAFETY CHECK-OUT
After correcting the original problem, perform the following
safety check before return the product to the customer.

1. Check the area of your repair for unsoldered 7. CAUTION: FOR

or poorly soldered connections. Check the CONTINUED PROTECTION
entire board surface for solder splasher and AGAINST FIRE HAZARD,
bridges. REPLACE ONLY WITH
SAME TYPE 2.5 AMPERES
2. Check the interboard wiring to ensure that no 125V/250V FUSE.
wires are "pinched" or contact high-wattage
resistors. RISK OF FIRE- ATTENTION: AFIN
2.5A 125V/250V
REPLACE FUSE
AS MARKED D'ASSURER UNE
2.5A 125V/250V

3. Look for unauthorized replacement parts, PROTECTION

particularly transistors, that were installed PERMANENTE CONTRE
during a previous repair. Point them out to the LES RISQUES D'INCENDIE,
customer and recommend their replacement. REMPLACER
UNIQUEMENT PAR UN
4. Look for parts which, though functioning, show FUSIBLE DE MEME, TYPE
obvious 2.5 AMPERES, 125/250
signs of deterioration. Point them out to the VOLTS.
customer and recommend their replacement.
8. WARNING:
5. Check the B + voltage to see it is at the values TO REDUCE THE
specified. ELECTRIC SHOCK, BE
CAREFUL TO TOUCH THE
6. Make leakage - current measurements to WARNING! PARTS.
HIGH VOLTAGE
determine that exposed parts are acceptably
insulated from the supply circuit before
returning the product to the customer.

2
 Confidential: FUJIFILM Service Center Use Only

X-Pro1 Service Manual

RoHS lead-free compliance

With the exception of parts and materials expressly excluded from the RoHS directive, all the internal connections and

component parts and materials used in this product are lead-free compliant under the European RoHS directive (*1). Use the

designated after-sales parts and the designated lead-free solder when performing repairs.

*1: Definition of lead-free

A lead content ratio of 0.1 wt% or less in the applicable locations (solder, terminals, electronic components, etc.)

<Lead-free soldering>
When lead-free solder is used, the solder tends to be less workable than when eutectic solder is used. When carrying out

repairs, use a designated lead-free solder, bearing in mind the differing work practices for eutectic solder and lead-free

solder.

■ Differences in the soldering work for lead-free and eutectic solder

Eutectic solder (Sn-Pb) Lead-free solder (Sn-Ag-Cu) Remark

Melting point 183°C 220°C

The bonding temperature that will

Soldering iron temperature 283°C 320°C
give the best bond strength.

Wetting Good Poor

Surface Gloss Matte

■ Recommended equipment

lead-free

Wire diameter

Solder type (Displayed symbol)

SnAgCu

■ Soldering iron maintenance

Because of the high soldering iron temperature in lead-free soldering, there is rapid carbonization of the flux adhering to

the tip of the soldering iron.

(1) Always cover the tip of the soldering iron with solder when it is not being used.

(2) If the tip is black from carbonization, wipe it gently with a paper towel soaked in alcohol until the solder will wet.

3
 Confidential: FUJIFILM Service Center Use Only

X-Pro1 Service Manual

MEMO

4
 Confidential: FUJIFILM Service Center Use Only

X-Pro1 Service Manual

CONTENTS

1. Disassembly ............................................................................................................1-1

2. Schematics ..............................................................................................................2-1

3. Adjustments ............................................................................................................3-1

4. Inspection ................................................................................................................4-1

5. Parts List 1 (Packing and Accessories) ......................................................................5-1

6. Parts List 2 (Mechanical Block) .................................................................................6-1

7. Electrical parts ........................................................................................................7-1

8. Appendix...................................................................................................................8-1

5
 Confidential: FUJIFILM Service Center Use Only

X-Pro1 Service Manual

MEMO

6
 Confidential: FUJIFILM Service Center Use Only

X-Pro1 Service Manual

1. Disassembly
1-1. Removing the CASE

(1) Remove the DECO PLATE LEVER.

(2) Remove the 1 screw.（MS2M 1.4X2.0）
(3) Remove the LEVER FINDER.

2
1

(4) Peel off the GRIP F.

(5) Peel off the TAPE GRIP F.
(6) Remove the 4 screws.（MS2M 1.7X3.5）
(7) Remove the BASE GRIP F.

5
6 65

4 5 7
4

6 6

1-1
 Confidential: FUJIFILM Service Center Use Only

X-Pro1 Service Manual

(8) Peel off the SHEET GRIP R LEFT.

(9) Peel off the SHEET GRIP R RIGHT.
(10) Peel off the SHEET GRIP F RIGHT.
(11) Peel off the SHEET GRIP F LEFT.

9
8
10 11

(12) Peel off the SHEET FRONT.

12

[Assembly]
Assemble by performing the disassembly procedure in reverse.
Refer to the sheet sticking procedure.
Recycling prohibition of SHEET.

1-2
 Confidential: FUJIFILM Service Center Use Only

X-Pro1 Service Manual

1-2. Removing the CONST REAR

(1) Remove the 1 screw.（N-MSGM 1.7X2.5）
(2) Remove the 4 screws.（N-MSGM 1.7×2.5D）

1
2 2

(3) Remove the 3 screws.（N-MS2M 1.7X3.0）

(4) Remove the 2 screws.（N-MSGM 1.7X4.0）

1-3
 Confidential: FUJIFILM Service Center Use Only

X-Pro1 Service Manual

(5）Open the CONST REAR in the direction of the arrow.

(6）Remove the REAR FFC from the MAIN PWB ASSY.

5
6

(7) Peel off the ULTAPE.

(8) Peel off the CUSHION CN LCD.
(9) Unlock the connector and remove the LCD FPC.

8
7

[Assembly]
Assemble by performing the disassembly procedure in reverse.

1-4
 Confidential: FUJIFILM Service Center Use Only

X-Pro1 Service Manual

1-3. Removing the CONST FRAME MAIN

(1) Remove the 1 screw.（MSGM 1.7×2.5）

(2) Remove the CONST PWB SIDE.

※Double-sided tape is applied at point A.
(3) Remove the CONST PWB SIDE FPC in the direction of the arrow.

2 3

1-5
 Confidential: FUJIFILM Service Center Use Only

X-Pro1 Service Manual

(4) Remove the 4 screws.（N-MSGM 1.7×2.5D）

4
4 4 4

(5) Remove the 1 screw.（N-MS2M 1.7×3.0）

(6) Remove the 2 screws.（N-MSGM 1.7×4.0）

6 6

1-6
 Confidential: FUJIFILM Service Center Use Only

X-Pro1 Service Manual

(7) Remove the 5 screws.（MSGM 1.7×2.5）

7
7
7
7

(8) Remove the 4 screws.（BT2M 1.7×3.5）

8
8

8
8

[Assembly]
Assemble by performing the disassembly procedure in reverse.

1-7
 Confidential: FUJIFILM Service Center Use Only

X-Pro1 Service Manual

1-4. Removing the CONST TOP

(1) Unlock the connector and remove the CONST TOP FPC.

(2) Remove the EYE SENSOR FPC.

(3) Remove the 1 screws.（N-MSGM 1.7×2.5）

1-8
 Confidential: FUJIFILM Service Center Use Only

X-Pro1 Service Manual

(4) Remove CONST TOP in the direction of the arrow.

[Assembly]
Assemble by performing the disassembly procedure in reverse.

1-9
 Confidential: FUJIFILM Service Center Use Only

X-Pro1 Service Manual

1-5. Removing the CONST FPC COMMAND

(1) Remove the CONST FPC、 COMMAND FPC

(2) Remove the 2 screws.（BT2M 1.7×5.0）

2
2

[Assembly]
Assemble by performing the disassembly procedure in reverse.

1-10
 Confidential: FUJIFILM Service Center Use Only

X-Pro1 Service Manual

1-6. Removing the MAINPWB ASSY

(1) Remove the solder in 6 locations.

1 1

1 1

1 1

(2) Remove the FPC AF.

(3) Unlock the connector and remove the FINDER DRIVE FPC.
(4) Remove the FINDER BL FPC.
(5) Remove the FINDER SHATTER FPC.
(6) Unlock the connector and remove the MOUNT FPC.
(7) Remove the SHATTER FPC.
(8) Unlock the connector and remove the CMOS FPC.

4 3
8 7
6

1-11
 Confidential: FUJIFILM Service Center Use Only

X-Pro1 Service Manual

(9) Remove the 2 screws.（BT2M 1.7×3.5）

(10)Lift off theY-10241MAINPWB ASSY in the direction of the arrow.

(11) Remove the EVF FPC.

11

10

[Assembly]
Assemble by performing the disassembly procedure in reverse.

1-12
 Confidential: FUJIFILM Service Center Use Only

X-Pro1 Service Manual

1-7. Removing the UNIT MOUNT

(1) Peel off the ULTAPE.
(2) Peel off the SHEET INSULATE SINK.
(3) Peel off the SHEET COND SINK.
(4) Peel off the SHEET CU SINK.

4
1
3
2

(5) Remove the 4 screws.（N-MSGM 1.7×2.5）

5
5

1-13
 Confidential: FUJIFILM Service Center Use Only

X-Pro1 Service Manual

(6) Remove the 1 screw.（MSGM 1.7×2.5）

(7) Remove the 2 screws.（MS2M 1.7×4.0）

(8) Peel off the SHEET COVER FPS.

1-14
 Confidential: FUJIFILM Service Center Use Only

X-Pro1 Service Manual

(9) Remove the SPEKER.

(10) Remove the 1 screw.（MSGM 1.7×2.5）

10

[Assembly]
Assemble by performing the disassembly procedure in reverse.

1-15
 Confidential: FUJIFILM Service Center Use Only

X-Pro1 Service Manual

1-8. Removing the HOLDER SYNCHRO

(1) Peel off the BONDO.
(2) Remove the solder in 1 location.

1
2

(3) Remove the NUT.

(4) Remove the PLATE SYNCHRO.

1-16
 Confidential: FUJIFILM Service Center Use Only

X-Pro1 Service Manual

(5) Remove the SYNCHRO TERMINAL from the HOLDER SYNCHRO.

[Assembly]
Assemble by performing the disassembly procedure in reverse.

1-17
 Confidential: FUJIFILM Service Center Use Only

X-Pro1 Service Manual

1-9. Disassembling the UNIT MOUNT

(1) Remove the screw (MS2M1.7X4.0).
(2) Remove the 4 screws (MS2M1.7X5.0B).

2
2

(3) Remove the FINDER UNIT in the direction of the arrow.

[Notes]
Be careful not to lose the NUT.

Be careful not to lose the NUT.

: Revised
1-18
 Confidential: FUJIFILM Service Center Use Only

X-Pro1 Service Manual

(4) Remove the 2 screws (MS2M1.7X4.0).

(5) Remove the FINDER BASE in the direction of the arrow.

4
5
4

(6) Remove 4 solders.

(7) Peel off the SHEET CU.

[Notes on Assembly]
SHEET CU is not reusable.

1-19
 Confidential: FUJIFILM Service Center Use Only

X-Pro1 Service Manual

(8) Remove the 3 screws (MS2M1.7X4.0).

[Tightening torque when assembly]

10N•cm
Tight the screws in the order show in the right picture.

(9) Remove the CMOS UNIT.

1-20
 Confidential: FUJIFILM Service Center Use Only

X-Pro1 Service Manual

[Notes]
• Be careful not to lose the SHIM.
• The thickness and the number of SHIMs vary depending on their positions. Be sure to write down the positions
beforehand so that the same SHIMs will always be set to the same positions during assembly as the original
positions.

SHIM

(10) Remove the 4 screws (BT2M1.7X3.5).

(11) Remove the GLASS PLATE.

10

11
11

11
11

[Notes]
When disassembling the CMOS UNIT, disassemble it [Sample image of a clean booth]
in a clean booth.
3
Compliant with ISO class 3 (0.3μm 100pcs/m ) or
better.
* Must clean up inside of the clean booth first before
you start clean up lenses.

1-21
 Confidential: FUJIFILM Service Center Use Only

X-Pro1 Service Manual

(12) Raise the DR GLASS UNIT in the direction of the arrow.

12

(13) Peel off the TAPE FPC, and remove the DR GLASS UNIT.

8
13

[Notes on Assembly]
• TAPE FPC is not reusable.
• Check the bosses to determine the position of the DR GLASS UNIT.

1-22
 Confidential: FUJIFILM Service Center Use Only

X-Pro1 Service Manual

(14) Remove the 3 screws (MS2M1.7X4.0).

(15) Remove the FP SHUTTER.

15
14

14

14
1

[Tightening torque when assembly]

10N•cm

(15) Remove 10 solders.

(16) Remove the screw (MS2M1.7X2.0).

16

15

[Tightening torque when assembly]

10N•cm

1-23
 Confidential: FUJIFILM Service Center Use Only

X-Pro1 Service Manual

(17) Remove the MOUNT FPC.

17

(18) Remove the 6 screws (MS7M1.7X6.0).

(19) Remove the MOUNT RING.

19
18 18

18 18

18 18

[Tightening torque when assembly]

18N•cm
Tight the screws in the order show in the right picture.

4 2

6 5

1 3

1-24
 Confidential: FUJIFILM Service Center Use Only

X-Pro1 Service Manual

(20) Remove the PSP MOUNT.

20

[Notes on Assembly]
Be sure to apply the lubricant to the PSP MOUNT.
Lubricant: ZS00185-100 (HI-LUBE FG-600T)

Good Example

Bad Example

(21) Remove the MOUNT LOCK.

21

1-25
 Confidential: FUJIFILM Service Center Use Only

X-Pro1 Service Manual

[Notes on Assembly]
Be sure to apply the lubricant to the MOUNT LOCK.
Lubricant: ZS00135-200 (LUBRICANT CFD-409Z)

(22) Remove the CSP MOUNT-LOCK.

22

(23) Remove the screw (MS2M1.7X3.0N).

23

[Tightening torque when assembly]

10N•cm

1-26
 Confidential: FUJIFILM Service Center Use Only

X-Pro1 Service Manual

(24) Remove the HOLDER MOUNT ASSY in the direction of the arrow.

24

[Precautions when replacing HOLDER MOUNT ASSY]

MASK_MOUNT is not reusable.

[Assembly]
Assemble procedure is reverse of the disassembly procedure.

1-27
 Confidential: FUJIFILM Service Center Use Only

X-Pro1 Service Manual

1-10. Removing the CONST ASSY FRONT and CONST BATT, COVER BATTERY
(1) Remove the 3 screws （MSAM 1.4×2.5N）.
1 1

(2) Remove the SHAFT in the direction of the arrow and then remove the COVER BATTERY.

[Assembly]
Assemble by performing the disassembly procedure in reverse.

1-28
 Confidential: FUJIFILM Service Center Use Only

X-Pro1 Service Manual

1-11. Attachment locations

(1) Affix the SHEET CU SINK as shown in the figure.

Right and left direction standard

Top and bottom direction standard

1-29
 Confidential: FUJIFILM Service Center Use Only

X-Pro1 Service Manual

(2) Affix the SHEET COND SINK as shown in the figure.

Right and left direction standard

Top and bottom direction standard

1-30
 Confidential: FUJIFILM Service Center Use Only

X-Pro1 Service Manual

(3) Affix the SHEET INSULATING SINK as shown in the figure.

Right and left

direction standard

Top and bottom direction standard

(4) Affix the UL_TAPE as shown in the figure.

Top and bottom

direction standard

Right and left

direction standard

(5) Affix the UL_TAPE (30X36mm) as shown in the figure.

（UL TAPE：ZS00169-100）

UL TAPE

Revised:[Link].2012

1-31
 Confidential: FUJIFILM Service Center Use Only

X-Pro1 Service Manual

(6) Affix the SHEET CU SINK （2 pieces）as shown in the figure.

SHEET CU SINK（2 pieces）

(7) Affix the UL_TAPE (19X37mm) as shown in the figure.

（UL TAPE：ZS00143-100）

UL TAPE

1-32
 Confidential: FUJIFILM Service Center Use Only

X-Pro1 Service Manual

(8) Affix the MASK_MOUNT on the HOLDER MOUNT ASSY as shown in the figure.

(9) Affix the TAPE FPCs on the MOUNT as shown in the figure.

: Revised
1-33
 Confidential: FUJIFILM Service Center Use Only

X-Pro1 Service Manual

(10) Affix the TAPE FPC on the BASE CMOS as shown in the figure.

(11) Affix the SHEET CU on the CMOUS UNINT as shown in the figure.

: Revised
1-34
 Confidential: FUJIFILM Service Center Use Only

X-Pro1 Service Manual

1-12. Putting of leather sheet

【Attention】
●Ethanol with much higher density more than 81.4 vol% is not recommended for cleaning.
When the surface of synthetic leather must be cleaned up to remove some dirt and dust, please use
"ethanol" with 76.9 to 81.4 vol% in density just as the cleaning substrate.
●Ethanol with much higher density more than 81.4 vol% is not recommended for cleaning.

<Grip press tool>

Pats. No Name Shape of the tip

ZJ01923-100 Grip press tool Type A

ZJ01924-100 Grip press tool Type B

ZJ01925-100 Grip press tool Type C

ZJ01926-100 Grip press tool Type D

ZJ01927-100 Grip press tool Type E

Revised:[Link].2012

1-35
 Confidential: FUJIFILM Service Center Use Only

X-Pro1 Service Manual

1-13. Procedure1
(1) I stick a seat and clean a part with ethanol.
<Clean an arrow part in particular chiefly.>

(2) I stick SHEET GRIP F RIGHT（①）on takeoff, CASE F.

Pasting standard: Top and bottom direction:CONST TOP insinuation.
Right and left direction:I make an insinuation at a lateral ups and downs shape.
Press power : More than 20N

(3) I press it in spite of all SHEET GRIP F RIGHT laps in Tool.

*1: A SHEET not having the mixture such as alien substances.
*2: To the ups and downs side get, and there not being advance.
*3: I press the lateral side.
(Grip press tool Type A: ZJ01923-100)

Type A

Revised:[Link].2012

1-36
 Confidential: FUJIFILM Service Center Use Only

X-Pro1 Service Manual

(4) I press the LENS side SHEET tip in push Tool

(Grip press tool Type A: ZJ01923-100)

Type A

(5) I press it with a big part of push Tool in the arrow direction.
*1: Press it until I expose it to (2) red bars region in the state that I hinted to the red horizontal line
side of superior wall (1) and am accompanied.
*2: I move to the bottom for a thing of push Tool and press it until I put it, and (2) red bars region is accompanied.
*3: In the state that moved to the bottom for a thing of push Tool, and hinted to red horizontal line region of
left wall (3) in (2) red bars I press it until I put it and am accompanied.
*4: I divide the whole red frame moiety into three times and press it.
(Grip press tool Type B: ZJ01924-100)

Type B
1

Revised:[Link].2012

1-37
 Confidential: FUJIFILM Service Center Use Only

X-Pro1 Service Manual

(6) I commute in the arrow direction with a curve part of push Tool and press it.
*1: I press it by coming and going until I press it until I expose it to (2) red lines region in the
state that let you comply with curve part (1) of LENS side GRIP and am accompanied and expose
it to (3) red lines side and am accompanied.
*2: I divide the whole red frame moiety into three times and press it.
(Grip press tool Type C: ZJ01925-100)

2
Type C

2
1
3

1-14. Procedure2
(1) I stick SHEET GRIP F LEFT (①) on takeoff, CASE F.
Pasting standard: Top and bottom direction:CONST TOP insinuation.
Right and left direction: I make an insinuation at a lateral ups and downs shape.

Revised:[Link].2012

1-38
 Confidential: FUJIFILM Service Center Use Only

X-Pro1 Service Manual

(2) I press it in spite of all SHEET GRIP F LEFT laps in Tool.

*1: A SHEET not having the mixture such as alien substances.
*2: To the ups and downs side get, and there not being advance.
*3: I press the lateral side.
(Grip press tool Type A: ZJ01923-100)

Type A

(3)I press the LENS side SHEET tip in push Tool.

(Grip press tool Type A: ZJ01923-100)

Type A

Revised:[Link].2012

1-39
 Confidential: FUJIFILM Service Center Use Only

X-Pro1 Service Manual

(4) I press it with a big part of push Tool in the arrow direction.
*1: I press it until I expose it to (2) red horizontal lines region in the state that I hinted to the red bar
side of upper wall (1) and am accompanied.
*2: I move to the left side for a thing of push Tool and press it until I expose it to (2) red horizontal
line moiety and am accompanied.
*3: I divide the partial whole of the red frame into twice and press it.
(Grip press tool Type B: ZJ01924-100)

Type B

(5) I commute in the arrow direction with a curve part of push Tool and press it.
*1: I press it until I expose it to (2) red line region in the state that let the curve part of the LENS side
grip (1) go and am accompanied (3) I press it by coming and going until I put it and am assigned
to the red line side.
*2: Move to the left side for a thing of push Tool, and press it by coming and going until put it,
and (2) red line part is accompanied; in (3) red line side I press it by coming and going
until I put it and am accompanied.
*3: I repeat the work mentioned above to (4) red line part.
*4: I divide it into three times and press it.

4 1
Type C

2
3

4 1

Revised:[Link].2012

1-40
 Confidential: FUJIFILM Service Center Use Only

X-Pro1 Service Manual

1-15. Procedure3
(1) I take out SHEET GRIP R RIGHT ( ① ) and stick it on CASE R.
Pasting standard: Top and bottom direction : CONST TOP insinuation.
Right and left direction: I make an insinuation at a lateral ups and downs shape.
*1: I perform pasting up from the position becoming the standard of right and left direction
and the top and bottom direction.
*2: I stick the right and left course on the basis of around cross KEY part.

(2) I press it in spite of all SHEET GRIP R RIGHT laps in Tool.

*1: A SHEET not having the mixture such as alien substances.
*2: To the ups and downs side get, and there not being advance.
*3: I press the lateral side.
(Grip press tool Type A: ZJ01923-100)

Type A

Revised:[Link].2012

1-41
 Confidential: FUJIFILM Service Center Use Only

X-Pro1 Service Manual

(3) I press it with a big part of push Tool in the arrow direction.
*1: I press it until I put it and am assigned to the red bar side of the right wall (1).
*2: It travels push Tool in the upper part of the card lid and presses it until I expose it to (2)
red horizontal line region and am accompanied.
*3: It travels push Tool in the bottom of the card lid and presses it until I expose it to (3)
red horizontal line moiety and am accompanied.
*4: I press it between (4) and (5) in the arrow direction.
*5: I divide the whole red frame moiety into three times and press it.
(Grip press tool Type B: ZJ01924-100)

Type B
2

1 4

(4) I commute in the arrow direction with a curve part of push Tool and press it.
*1: I press it until I expose it to (2) red line moiety in the state that let you go of the R LEFT side
grip curve part (1) and am accompanied and press it by coming and going until I expose it to (3)
red line side and am accompanied.
*2: I move to the right side for a thing of push Tool and press it by coming and going until I put it, and
(2) red line part is accompanied.
*3: I repeat the work mentioned above to (4) red line part.
*4: I divide it into three times and press it.
(Grip press tool Type C: ZJ01925-100)

1 Type C
4

Revised:[Link].2012

1-42
 Confidential: FUJIFILM Service Center Use Only

X-Pro1 Service Manual

1-16. Procedure4
(1) I stick SHEET GRIP R LEFT (①) on takeoff, CASE R.
Pasting standard: Top and bottom direction:CONST TOP insinuation.
Right and left direction: I make an insinuation at a lateral ups and downs shape.

*1: Perform pasting up from the position becoming the standard of right and left direction
and the top and bottom direction.

(2) I press it in spite of all SHEET GRIP R LEFT laps in Tool.

*1: SHEET not having the mixture such as alien substances.
*2: The thing that it runs, and there is not to a projection.
(Grip press tool Type A: ZJ01923-100)

Type A

Revised:[Link].2012

1-43
 Confidential: FUJIFILM Service Center Use Only

X-Pro1 Service Manual

(3) I press the lower finder tip of SHEET GRIP R LEFT and the tip of each SW penumbra of
DRIVE/AF/AE in push Tool.
*1: SHEET not having the mixture such as alien substances.
*2: The thing that it runs, and there is not to a projection.
(Grip press tool Type A: ZJ01923-100) Type A

(4) I press it with a big mask of push Tool in the arrow direction.
*1: I press it until I expose it to (2) red horizontal line region in the state that I hinted to the
red bar side of the left wall (1) and am accompanied.
*2: On the right side of push, the Tool size move, and press it until put it, and (2)
red horizontal line part is accompanied.
*3: I divide the whole red frame moiety into twice and press it.
(Grip press tool Type B: ZJ01924-100)

1 Type B
2

Revised:[Link].2012

1-44
 Confidential: FUJIFILM Service Center Use Only

X-Pro1 Service Manual

(5) I commute in the arrow direction with a curve part of push Tool and press it.
*1: I press it until I expose it to (2) red line region in the state that let the R LEFT side grip
curve part (1) go and am accompanied and press it by coming and going until I expose
it to (3) red line side and am accompanied.
*2: I move to the right side for a thing of push Tool and press it by coming and going until
I press it by coming and going until I expose it to (2) red line moiety and am accompanied
and expose it to (3) red line side and am accompanied.
*3: I repeat the work mentioned above to (4) red line part.
*4: I divide it into three times, and press it.
(Grip press tool Type C: ZJ01925-100)

1 4 Type C

(6)Press of press tool in the arrow direction.

*1: Divide it into seven times and push it
*2: Divide it into six times and push it
(Grip press tool Type E: ZJ01927-100)

Type E

Revised:[Link].2012

1-45
 Confidential: FUJIFILM Service Center Use Only

X-Pro1 Service Manual

(7)Press of press tool in the arrow direction.

*1: Divide it into 13 times and push it
*2: Divide it into four times and push it
(Grip press tool Type D: ZJ01926-100)

Type D

Revised:[Link].2012

1-46
 Confidential: FUJIFILM Service Center Use Only

X-Pro1 Service Manual

1-17. Procedure5
(1) I take out BASE GRIP F (①), and possess CASE F of the camera body and close
a screw (②) to CASE F.
*1: I tighten a screw while approaching to the thickness direction of the camera body and lose it.
Clamping order : ①→②→③→④
Screw total torque : 0.10±0.02N・m

2
4

1
3

(2) I take out TAPE GRIP F (③) and stick it on BASE GRIP F after detachment paper stripping.
Pasting standard: Direction of right and left: Chart below standard A part insinuation
Top and bottom direction: Chart below standard B part insinuation
*1: Perform pasting up from the position becoming the standard of right and left direction and
the top and bottom direction.
*2: Press the whole enough so that tape adheres.

Standard B

Standard A

Revised:[Link].2012

1-47
 Confidential: FUJIFILM Service Center Use Only

X-Pro1 Service Manual

(3) I stick GRIP F (④) on takeoff BASE GRIP F/TAPE GRIP F.

Pasting standard: Direction of right and left: Chart below standard A part insinuation
Top and bottom direction: Chart below standard B part insinuation
*1: GRIP F to BASE GRIP F runs; impossibility (all laps department)
*2: Press GRIP F from the top so that a gap does not occur in GRIP F and BASE GRIP F.

Standard B

Standard A

(4) I take out LEVER FINDER (⑤), and possess CASE TOP and close a screw (⑥) to CASE TOP.
Screw total torque : 0.14±0.02N・m

(5) I take out DECO PLATE LEVER (⑦) and stick it on LEVER FINDER after detachment stripping.

Revised:[Link].2012
Revised:[Link].2012

1-48
 Confidential: FUJIFILM Service Center Use Only

X-Pro1 Service Manual

1-18. Disassembling the FINDER

＊ Do the dissolution of finder department, in the case that the garbage, dirt removal inside the finder are necessary.

＊ Clean environment where garbage is not in if possible.

＊ Lens which varies in zoom ratio makes a evacuation.

(1) Lens which varies in zoom ratio makes a evacuation.

(2) Take off five hooks
(3) Lift up the FINDER COVER in the direction of the arrow.

2
2 3

(4) Clean with air blow or applicator.

[Assembly]
Assemble by performing the disassembly procedure in reverse.

Revised:[Link].2012

1-49
 Confidential: FUJIFILM Service Center Use Only

X-Pro1 Service Manual

MEMO

1-50
 Confidential: FUJIFILM Service Center Use Only

X-Pro1 Service Manual

2. Schematics
2-1. Block Diagram
1.8V 3.3V
I2C_SCL1
New Current JTAG
I2C_SDA1
L5V L3.3V -1.5V 1.8V 4.5V 1.0V FLASH
3.3V Eye
COPRO_PW_EN 1.1V
1Gbit (NAND) MEDIA Vout SENSER
SD or SDXC
LENS MOUNT

SHUTTER UNIT
OLPF
CoPro_48M
Image Area CMOS IMX095 Co-Pro SD CARD
APS size
CoPro_PLLLOCK EVF 0.47” 3.3V
CDS ADC RST CARD BUS Slot
16 M pixels IBFC 1 44M

Parallel I/F
LVDS to
CoPro_RST
12bit Contro AUTO EVF BL 10V
CAM RECC EVF_RD[7:0], EVF_GD[7:0],
EVF_BD[7:0],EVF_CLK, CSIO_2
Adjustment Serial CCDIF EVF_HD,EVF_VD,EVF_RST_N EVF_CS_N CTL
parameter Tx MVBLK
EXI
CAM_D[0:7]_P/M EXDREQ EXDREQ MEDIA LCD Panel 3.3V
F UART LCD_D[7:0],LCD_CLK,
CAM_SCK_P/M
RECC EXDACK EXDACK MFT
LCD_HD,LCD_VD,LCD_RST_N
3.0”
YCPRO
RST
EXALE EXALE TFDC
EVR CSIO_2
0.92M
EXDWR EXDRW
Contro EXDCKO EXDCKO ENCD WDT
LCD_CS_N CTL
PIEZO

TG/SG ME EXDCKI EXDCKI LCD_BL_DM

PLL GCON TX49 CPU Core
ARM1136J-S Core DAC BL LED x5
(Programabl MC EXT_D[0:15] LCD_BL_EN
LCD_BL
CLKC
6V e) LCD_BL
KEY LENS MT UIF N

DEBUG I/F MULTI USB

VSYNC,,EM_EXT1/2
SDI_INT,LENS_DET

BUS120MHz
96MHz
SIO
CSIO CSIO_2
5V SENS_THM
I2C_SCL2
I2C_SDA2

CN Cable LCD_CS_N
LENS_PWON1/2

FPS DR USB2.0 8p
IO_AV_DET_

PeripheralBUS
LV8402GP
CSI0_3 CPU Core
+
CAM_CS_N PORT
CAM_THM_DA HMDI_INT
DR_IN1A/1
B

Peripheral
ICU
CHG_PI
XSW_PI

CHG_INA/B CSI0_3
CHG_MODEa/2 CoPro CS N
Face Detect
ADC
SM_OM,AM_ON IC I-cache 16k
D-
JPEG 16k cache
CSI0_1 TMDS
BUS Cont.
Output
FLASH-XE TTL_SHOE FLASH_XTrig SDRAMC I2C TTX0,TX1,
DMAC TTX2,TXC
Status Indicator Master HDMI
LED G I2C_SCI1
LED Level TypeC
I2C_SDA X’TAL HPD
LED
LED R SENSER 1
RCS I2S
CN
48.00M
CSI0_0 Hz 3.3V I/O Buffer ROM HDMI_DDSCL, 19pinI
MOT Drv
HVF / MOT_CS_N HDMI_DDSDA
BU24024GU
8kb x32
AFLED
1.8V 3.3V

KEY_PW_lever_DL
KEY_PW_lever
or SELF TIMER

KEY_S1_UIF_N
VBS_75_DA
EVF_BL DDR2 2Gb x32
ELPIDA
FPS_PI 1Gb 2
I2C_SCL
1 VDA DO Video
KOI CTL Driver
Li-ion_2Cell
7+2ch PMG_PW_CTL1 AU_DA SPEAKE
BATT AU_M_CLK
5V I2
NP-** AU B CLK,AU F CL
DA SP AM
S
1.1V
1260mAh Series DDRVDD
POWR AU_SDI AD STREO L-MIC
1.8V REG
HDMI AU_SDO MIC AM
1 5V
FUSE 3.3V CTL R-MIC
PMG_PW_CTL 0 / 1

EVF 10V Series CSIO_2

5V CMOS_-1.5V
CMOS -6V REG PMG_CS_N
2CELL V
-1.5V Rear KEY 3.3V
StepDown
LCD BL OK/BACK/MVREC/ TOPKEY Power RESETIN
LENS 3.3V Shortcut SW PWSW1
2CELL V RELEASE SW(S1/S2)
StepDown A_1.8V R/L/D/U SW Fn_SW, CMD DIAL
on
COMMAND DIAL LENS_DET_N PWSW0 Res
A_3.0V CMOS_4.5V
COPRO_PW_EN Series PLAY SW
2CELL 5V
StepDown copro 1V REG Tv DIAL BATT
4.5V
Ev DIAL RTC CTL
LENS 5V Backup
FPS 6V
32.768kHZ

2-1
 Confidential: FUJIFILM Service Center Use Only

X-Pro1 Service Manual

2-2. Overall connection Diagram

A B C D E
CN552 BL509_12G31
PI_T_E 1 2
PI_T_K 1 1 1 2
PI_T_V 1 0 1 1
FINDER PI_W_E
PI_W_K
9 10
8 9
0.5_NZIF 6 6 EVF_BL_C
LENS 7 8
1 UNIT
PI_P_E
PI_P_K
PI_P_V
DUMMY
6 7
5 6
4 5
CN12 0.5_NZIF
5
4
3
5 EVF_BL_C
4
3
2 EVF_BL_A
2
DUMMY 3 4 1 EVF_BL_A
2 3 1
DCM-
DCM+ 1 2
1 CN6 51281_0694 CN772

EVF FS-B+ 8
FS-A- 7 8
FS-A+ 6 7
11
CN771
VID12-B

SHUT FS-B- 5 6
NC 4 5
FSPR-C 3 4
0.5_NZIF 2 2
3 3
4 4
VID11-B
VID10-B
VID9-B
5 5

UNIT
FSPR-V 2 3
FSPR-E 1 2
CN551 51281_10894
CN8 6 6
7 7
8 8
VID8-B
VID7-B
VID6-B
EVF BL
VID5-B
9 9
EYELED_A 1 1 10 10
VID4-B
VID3-B TOP_PWB
DET EYE_DET 2 2
EYE_VCC 3 3
GND 4 4
0.5_NZIF
11 11
12 12
13 13
VID2-B
VID1-B
VID12-G
EVF
EYE_VIO 5 5 14 14
IC EYE SENSOR FPC I2C_1_SDA 6 6
I2C_1_SCL 7 7 CN8 15 15
16 16
VID11-G
VID10-G
VID9-G UNIT
GND 8 8 17 17 VID8-G
CN853 51281_0894
DR 3 3 3 3
18 18
19 19
20 20
VID7-G
VID6-G
VID5-G
0.47inch
LENS MOUNT DR 3 2 3 2
DR 3 1 3 1
BK_U
21 21
22 22
VID4-G
1.44M DETECTOR
DR 3 0 3 0
5V 2 9 2 9
5V 2 8 2 8
BK_L 23 23
24 24
25 25
VID3-G
VID2-G
VID1-G
5V 2 7 2 7
5V 2 6 2 6
5V 2 5 2 5
CN33 CN51 26 26
27 27
28 28
VID12-R
VID11-R
VID10-R
5V 2 4 2 4 29 29
VID9-R
VID8-R
S1/S2
5V 2 3 2 3 30 30
GND 2 2 2 2 31 31
VID7-R
VID6-R DIAL1/2
2 MOUNT FPC
GND 2 1 2 1
GND 2 0 2 0
GND 1 9 1 9
GND 1 8 1 8
32 32
33 33
34 34
35 35
VID5-R
VID4-R
VID3-R
FN
PWR
GND 1 7 1 7 VID2-R
GND 1 6 1 6
36 36
37 37
VID1-R
VSSX
EXT_TRG
DGND 1 5 1 5 38 38 DX
DGND 1 4 1 4 39 39
DGND 1 3 1 3
DGND 1 2 1 2
DGND 1 1 1 1
RCS 40 40
41 41
42 42
CLX
ENBX4
ENBX3
ENBX2
VIEWPWB
INTR_BUSY 1 0 1 0
VSYNC 9 9
MT_MOSI 8 8
System 43 43
44 44
45 45
ENBX1
NRG
VDD
STATUS
LED
MT_SCK 7 7 46 46
MT_MISO 6 6 DIRY
47 47 ENBY
LENS_DET_N 5 5 48 48 CLY
DUST

2 KEY_VIEW_UIF_N
3.3V 4 4 49 49
3.3V 3 3 DY
50 50 VSSY
3.3V 2 2 51 51

9690S_05Y901 NM

4 4 LED_G_ON_N
5 5 LED_R_ON_N
LCCOM
3.3V 1 1
REDUCTION Copro

3 3 +3_3VRUN
CN951 AYF333395DW1 CN2302
PIEZO

-
CN855
CN601 51281_1894 1 1 KEY_MODE2_DA_UIF 1 1

UNIT FPC EV3 2 2

BK_L

GND
CHG_PI_E 1 8 1 8 2 2 KEY_MODE2_DA_UIF

CN3601
Handsolder * 4 3 3 EV3 KEY_MODE1_DA_UIF 3 3
CHG_PI_C 1 7 1 7 KEY_FN_UIF_N 4 4
CHG_PI_V 1 6 1 6 4 4 KEY_MODE1_DA_UIF
5 5
CN23

1 1
5 5 KEY_FN_UIF_N KEY_POWER_UIF_N_pre

FOCAL
GND 1 5 1 5
6 6 KEY_POWER_UIF_N_pre MAIN KEY_S1_N_pre 6 6

2
X-SW 1 4 1 4 7 7
FPS COM(GND) 1 3 1 3
SM_DRV 1 2 1 2
7 7 KEY_S1_N_pre
8 8 KEY_S2_UIF_N
KEY_S2_UIF_N
STRB_TRG_EXT 8 8 14 14 EXT_CS

PLANE AM_DRV 1 1 1 1 9 9 STRB_TRG_EXT

1 0 1 0 OUT6B to OUT6B
OUT6A
9 9
10 10
13 13
12 12
EXT_SDIO
EXT_SCK

FPC SM_PI_V 1 0 1 0
SM_PI_C 9 9
0.5_NZIF
1 1 1 1 OUT6A STRB_EXT_CS_N 11 11
12 12 BK_U 11 11
10 10
GND
KEY_VIEW_UIF_N
SHOE
SHUTTER
SM_PI_E 8 8
(DUMMY) 7 7
1 2 1 2 STRB_EXT_CS_N
1 3 1 3 +3_3VRUN TOP +3_3VRUN
CSIO0_SDO 13 13
14 14
9 9
8 8
+3_3VRUN
LED_R_ON_N
CHG_MODE_DRVA 6 6
CHG_MODE_DRVB 5 5
CHG_DRVA 4 4 CN18
1 4 1 4 CSIO0_SDO
1 5 1 5 LED_G_ON_N
1 6 1 6 CSIO0_SCK
FPC
LED_R_ON_N
CSIO0_SCK
LED_G_ON_N
15 15
16 16
CN16 7 7
6 6
LED_G_ON_N
MIC_L-
FPC
1 7 1 7 LED_R_ON_N KEY_VIEW_UIF_N 17 17 5 5 MIC_L+
CHG_DRVA 3 3 GND 18 18 4 4 MIC_R-
1 8 1 8 KEY_VIEW_UIF_N
3 CHG_DRVB 2 2
CHG_DRVB 1 1
BK_U
1 9 1 9 GND
2 0 2 0 MIC_L-
2 1 2 1 MIC_L+
MIC_L-
MIC_L+
MIC_R-
19 19
20 20
21 21
3 3
2 2
MIC_R+
OUT6A
1 1 OUTC6NB2301
CN101 2 2 2 2 MIC_R- MIC_R+ 22 22 BL509_14G31
FGB216-0611 FGB216-0611
2 3 2 3 MIC_R+ 23 23
11
2 2
3 3
4 4
GND
GND
+5VRUN
CN1201
GND
GND
GND
1
12
2
3 3
CN23 AYF332395DW1 MT
503566_5100
BK_DW
CN41 AYF332395DW1
+5VRUN +5VRUN 4 4
5 5 5 5 CN741
6 6
+5VRUN
+5VRUN
+5VRUN
+5VRUN 6 6 11 TOP
MIC
7 7 GND +5VRUN 7 7 BL+
2 L
CAM_PWB 8 8
9 9
10 10
11 11
12 12
-6VCMOS
+1_8VRUN
+1_8VRUN
+1_8VCMOS_A
GND
-6VCMOS
+1_8VRUN
+1_8VRUN
8 8
9 9
10 10
11 11
2
3 3
4 4
5 5
BL-
NC
VCOM
+1_8VCMOS_D +1_8VCMOS_A 12 12 PVDD
13 13 +1_8VCMOS_D +1_8VCMOS_D 13 13 6 6
14 14 +3_3VRUN +1_8VCMOS_D 14 14
VDD3
15 15 GND +3_3VRUN 15 15
7 7 VDD3CFP0
16 16 16 16 8 8 VDD3CFN0
pin

GND GND
17 17 GND GND 17 17 9 9
18 18 18 18
GVDD
BK_U 19 19
20 20
DOP00
DOM00
GND
GND
DP00
DM00
19 19
20 20
10 10
11 11
NVDD
VDM2CFP0
MIC
pin

21 21 DOP01 GND 21 21 12 12 VDM2CFN0 R

FPS009_2900_0
22 22 DOM01 DP01 22 22 13 13
CN61 23 23
24 24
25 25
GND
DOP02
DM01
GND
23 23
24 24
25 25
14 14
15 15
VREFH
COMDC
CN903

DOM02 DP02 COMAC

10 10 CARD_DET

13 13 SCRU_GND
14 14 SCLU_GND
15 15 SCLD_GND
16 16 SCRD_GND
26 26 GND DM02 26 26 16 16
2 CD/DAT3

VBRT

-
27 27 DOP03 GND 27 27
P1.5:P330

28 28 28 28 17 17 AVDD
11 11 COMON

DOM03 DP03
DAT2

29 29 29 29
8 8 DAT0
9 9 DAT1

GND DM03 18 18 VSS

3 3 CMD
4 4 VSS
5 5 VDD
6 6 CLK
7 7 VSS

30 30 DCKP GND 30 30 19 19
12 12 WP

31 31 DCKM DPCK 31 31 VDD2

32 32 GND DMCK 32 32 20 20 VDD2CFP1
33 33 DOP04 GND 33 33 21 21
1 1

34 34 DOM04 DP04 34 34
VDD2CFN4 AFLED
35 35 GND
CMOS DM04 35 35
22 22 VDD2CFP0
2

36 36
37 37
DOP05
DOM05
GND
DP05
36 36
37 37
23 23
24 24
V5D0D126C1F6N_05185 LCD UNIT
38 38 38 38
VDD
GND DM05 25 25 3.0inch.
39 39
40 40
41 41
42 42
DOP06
DOM06
GND
DOP07
GND
DP06
DM06
GND
39 39
40 40
41 41
42 42
SDCARD_CN 26 26
27 27
28 28
VDD
VDDIO_M
VDDIO_G 0.92M
43 43 DOM07 DP07 43 43 VSS
44 44
45 45
46 46
GND
GND
GND
to DM07
GND
GND
44 44
45 45
46 46
29 29
30 30
31 31
TEST
BLC

4 APS-CMOS 47 47
48 48
49 49
50 50
51 51
CAM_THM_DA
CAM_DC1
CAM_DC2
PMG_PW_CTL0
GND
GND
CAM_THM_DA
CAM_DC1
CAM_DC2
PMG_PW_CTL0
47 47
48 48
49 49
50 50
51 51
32 32
33 33
34 34
DVDD
XVD
XHD
DCLK
52 52
53 53
54 54
55 55
CAM_CLK
GND
CAM_HD
CAM_VD
MAIN GND
CAM_CLK
GND
CAM_HD
52 52
53 53
54 54
55 55
BK_L 35 35
36 36
37 37
D0
D1
D2
38 38
56 56
57 57
58 58
CAM_SCK
CAM_SDO
CAM_VD
CAM_SCK
56 56
57 57
58 58 CN61 39 39
D3
D4
59 59
60 60
61 61
CAM_CS_N
CAM_RST_N
GND
CAM_SDO
CAM_CS_N
CAM_RST_N
59 59
60 60
61 61
BK_L 40 40
41 41
42 42
D5
D6
GND

503425_6191
FPC GND

503425_6191
CN51 43 43
44 44
45 45
D7
VSS
XCS
SI
46 46 XSCK
47 47 XRST
48 48 TEST
49 49 VDDIO_G
50 50 TEST
CN852 51 51 -
CN3501 VSS
11
2 2
KEY_MVAEAF_UIF_N KEY_MVAEAF_UIF_N
2
11
2 REAR_PWB
3 3
4 4 SIDE 3 3
4 4 NJIF 11
CN856

FFC
CN3001
5 5 GND
9690S_05Y901
FFC 9690S_05Y901
GND 5 5
CN5 N-JIF 2 2
3 3
+3_3VRUN
KEY_UDLR
KEY_OBFS
+3_3VRUN
KEY_UDLR
OK/BACK/F/S
5
4 5
3 4
SIDE PWB KEY - -
CN5
4 4
5 5
KEY_PLAY_UIF_N
GND
KEY_PLAY_UIF_N
GND
2 3
1 2
1
U/D/L/R
11
9690S_05Y901
CN901
SHIELD_2_GND
9690S_05Y901
N-JIF OK/BACK
PLAY
CN6002 COMMAND
HDMI 2 2
3 3
4 4
DATA2+
DATA2-
-

SHIELD_1_GND
CN5
CN854 5 5
FINDER KEY_EVF_OVF_UIF_N
GND
1
2
3
1
2
3
KEY KEY_CMD_R_UIF_N
KEY_CMD_DET_N
1
2
1
2
NJIF TypeC 6 6
7 7
DATA1+
DATA1-
SHIELD_0_GND
4 KEY_CMD_L_UIF_N 3 3 CN5 8 8 DATA0+
5 FPC DETECTOR
9690S_05Y901
4
5 5 NJIF
CN5
KEY_EVF_OVF_UIF_N
GND
9690S_05Y901
4
5
4
5
Multi
9 9
10 10
11 11
DATA0-
SHIELD_C_GND
CLOCK+
- 12 12 CLOCK-
MT
CN BACKUP
13 13
14 14
CEC_GND
CEC
COMMAND FPC BATT. 15 15
16 16
17 17
SCL
SDA
GND 12 12
GND 11 11
GND 10 10

NC
GND 1 1

18 18
GND 9 9
VBUS 8 8
D- 7 7
GND 6 6
D+ 5 5
AV_DET_N 4 4
AUD_L 3 3
VBS 2 2

SPK 19 19
+5V
HotPlugDetect
FGY119-008100

CN851
AF GND 1 1
20 20 GND
10L_0000_CN2

21 21 GND
KEY_MVAEAF_1 2 2 22 22 GND
KEY_MVAEAF_2 3 3 23 23
CN902

FPC KEY_MVAEAF_DA 4 4
NJIF
24 24
GND
GND
-

-
DETECTOR GND 5 5 25 25 GND
9690S_05Y901 CN5 TCX3278_310187

-
MAIN_PWB

2-2
 Confidential: FUJIFILM Service Center Use Only

X-Pro1 Service Manual

2-3. Mounted Parts Diagrams

2-3-1. MAIN PWB ASSY

%7
)

2-3
 Confidential: FUJIFILM Service Center Use Only

X-Pro1 Service Manual

2-3-2. SHOEFPC

D
/('

1 2 3 4 5 6 7 8 9
2-4
 Confidential: FUJIFILM Service Center Use Only

X-Pro1 Service Manual

3. Adjustments
3-1. Important point before adjustment (the internal memory deployment model)
3-1-1. The handling of image files in internal memory
Image files contained in the internal memory should be handled as described below.
<Procedure for handling images>
When either of following work is necessary, as many as possible of the image files should be extracted from the
camera's internal memory and then written into the internal memory in the repaired or replacement camera before
the camera is returned to the customer.
1. When the replacement camera is provided.
2. When the MAIN PWB ASSY is replaced.
--->When "MAIN PWB ASSY" is replaced, it is necessary to execute "Flash memory reset".
(When the "Flash memory reset" was executed, involve formatting the internal memory.)
*Note
For PTP-connected cameras, carry out the procedure in "ii. Procedure for PTP-connected cameras and images
that cannot be downloaded to a PC".

<Image file transfer procedure>

I. Procedure when images can be downloaded to a PC
* If an memory card is inserted, data in the internal memory cannot be backed up.
(1) Back up the images stored in internal memory.
• Create a folder (named and located so as to avoid any confusion with the user's images).
• Without inserting an memory card, connect the camera to a PC and copy the image files on the removable
disk recognized by the PC to the folder created in the previous step.
• Check that the images can be displayed correctly on the PC.
(2) Return the backed up image files from the PC to the camera.
• Turn the camera on without an memory card inserted and format the camera's internal memory.
• Without inserting an memory card, connect the camera to the PC and copy the image files from the folder
containing the images backed up in the previous step onto the removable disk recognized by the PC.
• Check that the images can be displayed correctly on the camera.
• Delete the backup files created on the PC in step (1) (the user's image files).

II. Procedure when images cannot be downloaded to a PC

(1) Back up the images stored in internal memory.
• Insert an memory card to be used for image backup into the camera and format the card.
• From the SETUP menu, reset the frame numbers.
• Select image copying from the playback menu, select "Camera -> Card" for all the frames and then copy the
images.
• Check that the images can be displayed correctly on the camera.
(2) Return the backed up image files from the memory card to the camera.
• Before inserting the card, format the camera's internal memory.
• Insert the memory card containing the backed up copies of the user's image files.
• From the SETUP menu, reset the frame numbers.
• Select image copying from the playback menu, select "Card -> Camera" for all the frames and then copy the
images.
• Remove the memory card and check that the images can be displayed correctly on the camera.
• From the SETUP menu, set the frame numbers to the default sequence.
• If the image file numbers have changed, always notify the user in writing that the image file numbers have
changed.
III. Procedure for PTP-connected cameras and images that cannot be downloaded to a PC
(Images can only be backed up to a PC. * Normally, back up images using procedure II.)
(1) Back up the images stored in the camera's built-in memory.
• Create an FAIS receive number folder (to ensure error-free user image management).
• Without inserting an memory card, connect the camera to the PC and check the image files in the camera
on the PC. Then copy those files to the folder described on the previous page.
• Check that the images can be viewed successfully on the PC.
(2) Return the backup image files from the PC to the camera.
• With no memory card inserted, turn the camera on and format the built-in memory.
• Using a card reader or similar device, check the memory card to be used for image file backup on your PC.
• Copy the image files from the image file backup folder on the previous page into the "DCIM\100_FUJI\"
folder on the image file backup memory card.
• Using a safe procedure, remove the image file backup memory card from your PC.
• Load the image file backup memory card into the camera.
• Select "Copy image" in the Playback menu, select all the frames in "Card -> Camera" and then copy the
images.
• Remove the memory card and check that the images can be viewed successfully.
• Delete the backup files (user image files) created on the PC in step (1).

3-1
 Confidential: FUJIFILM Service Center Use Only

X-Pro1 Service Manual

3-1-2. Adjustment when replacing major parts

<Note>
Depending on the temperature inside the camera (approx. 15°C or below or 50°C or above) a "Temperature NG" error may
occur during X-Pro1 adjustment.
When a "Temperature NG" error occurs, turn the camera off and leave it for a short time before resuming the adjustments.
Check the ambient temperature also as this can influence the procedure.

 Adjust the item shown by O in the table below at the part replacement of Y-10241MAIN PWB, UNIT MOUNT, CONST ASSY
FRONT and FP SHUTTER (Other part replacements need not be adjusted).
Replacing parts
Y-10241 CONST ASSY
No.
MAIN PWB ASSY
UNIT MOUNT
FRONT FP SHUTTER
Adjustment item
0 MAIN PWB Initialize([Link]) *1 O
1 Mount Data Write O O O
2 Level Adjustment(Normal temperature) O O O
3 CMOS Defect Correction O O O
4 Camera Adjustment O O O O
5 Level Adjustment(High temperature) O O O
6 EVF Adjustment O O O
7 Battery Voltage Adjustment O O O
8 Firmware Download Do not use it until there is an instruction.
Do the end setting when you end the adjustment software when you set
9 End Setting
the camera to the Jig mode.
* The firmware is not installed in new Y-10241MAIN PWB ASSY. When Firmware Download is not executed first, it doesn't
*1
operate normally.
When the Y-10241MAIN PWB ASSY has been replaced, always reset the MAIN PWB Initialize before making any other
adjustments.

3-2. Measuring instruments used

Measuring equipment Remarks
Regulated power supply For adjustment
Pattern box PTB450F
Digital voltmeter For Battery adjustment
Used for various adjustments and operation checks (PC-AT compatible)
PC *1 *2
OS : Win 2000 SP4, XP SP2
Brightness meter LS-110 (Minolta) or equivalent
Color temperature meter Color Meter IIIF (Minolta) or equivalent
Flash meter For adjustment and function inspection
*1: PC condition
1. Hardware recommendation: CPU; Pentium4 2.4GHz or better, Available MAIN MEMORY; 512MB or more.
It might make an error of the adjustment when the performance of PC is low.
2. Video Jig must be installed.
3. Check that Microsoft .NET Framework Version 2.0 is installed.
*2: To install Microsoft .NET Framework Version 2.0 in Windows 2000 SP4, you must first install Windows Installer 3.0.

: Revised
3-2
 Confidential: FUJIFILM Service Center Use Only

X-Pro1 Service Manual

3-2-1. Installing .NetFramewark Version 2.0

<Step 1>
Download .NET Framework Version 2.0 from Microsoft.
(See the address below and light picture.)
[Link]
856EACB-4362-4B0D-8EDD-AAB15C5E04F5&displaylang=e
n

<Step 2>
After downloading the software, complete the installation as
directed by the Install wizard.

3-2-2. Installing Windows Installer 3.0(Windows 2000 SP4 only)

<Step 1>
Download Windows Installer from Microsoft.
(See the address below and light picture.)
[Link]
FBC5470-B259-4733-A914-A956122E08E8&displaylang=en

<Step 2>
After downloading the software, complete the installation as
directed by the Install wizard.

3-3
 Confidential: FUJIFILM Service Center Use Only

X-Pro1 Service Manual

3-3. Use jig list

Pats. No Name Comment Remarks
ZJ00699-100 Filter LB145 Camera adjustment Common with the FinePix F700
ZJ00653-100 LB145 filter holder kit for X-Y stage Camera adjustment Common with the FinePix F700
--- USB cable General adjustment This is bundled to the product
ZJ00581-100 Discharger Discharge for FLASH UNIT
ZJ00585-100 LCD adjustment jig EVF adjustment Common with the FinePix S304
ZJ00631-100 LCD JIG COVER EVF adjustment Common with the FinePix S304
ZJ01134-100 QR Cord reader MOUNT DATA Read Common with the FinePix S8000fd
ZJ01936-100 NP-W126 Battery jig 調整全般 New jig
--- Power Cable Jig （9V） General adjustment Accessory sold in the market
--- AC Adapter（AC-9V） General adjustment Accessory sold in the market
FZ09420-100 DC COUPLER CP-W126 General adjustment New jig
ZJ01971-100 X-Pro1 W PC Soft Ver.1.00 PC adjustment Windows 2000 / XP English OS *1
ZJ01970-100 X-Pro1 SD BOOT Soft [I] Main PWB Initialize New jig *1
ZJ01849-100 FxHS20EXR/X100 Level chart Level adjustment Common with the FinePix X100
ZJ01935-100 X-Pro1 Level jig Level adjustment New jig
ZJ01858-100 Rotation axis Stand Level adjustment Common with the FinePix X100
--- FUJINON LENS XF18mm F2 R Level adjustment Products available from stock
--- FUJINON LENS XF35mm F1.4 R Camera adjustment Products available from stock
--- Laser telemeter Level adjustment Common with the FinePix X100*3
Maker : Makita, Model : SK308PZ
When it's following specification equal
to "SK308PZ", the Laser telemeter
container is practicable.
･Precision : ±1mm/10m
･Line Point laser :
X direction/Y direction
*1: Please downloaded from Web server ([Link] or [Link]
*2: Select one the power cable suitable each country.
*3: Marketing product. Please purchase it in a general merchandising store.

Revised:[Link].2012

3-4
 Confidential: FUJIFILM Service Center Use Only

X-Pro1 Service Manual

3-4. Calibration method of pattern box

<Use the pattern box for Camera adjustment>
Turn on the power supply in the pattern box.
Afterwards, wait for about ten minutes so that the source of light may stabilize.

(1) Brightness
160 ± 5cd/m2 (with LB145 filter)
No chart, center of pattern box
Minolta brightness meter LS-110 or equivalent
* Calibration method
Place the filter (LB145) against the pattern box. With
the filter (LB145) in contact with the brightness meter,
adjust the pattern box brightness to 160 ± 5cd/m2.

(2) Color temperature

6100 ± 50K (with LB145 filter)
No chart, center of pattern box
Minolta color meter IIIF or equivalent
* Calibration method
Place the filter (LB145) against the pattern box. With
the filter (LB145) in contact with the color temperature
meter, adjust the pattern box color temperature to 6100 Calibration method of pattern box
± 50K.

3-5. Adjustment software installation

3-5-1. Installation of DSC jig driver

* Since this camera uses the USB for communications with the personal computer, in order to start the PC adjustment
software, [the DSC jig driver] needs to be installed in the personal computer beforehand.
* The DSC jig driver is the same as that for the FinePix S7000, so if this jig driver software is already installed in the personal
computer, it is not necessary to install it. The procedure is given below.

<Step 1>
DSC jig driver ([Link]) is downloaded from Web
server ([Link]

<Step 2>
Defrost the downloaded compression software

<Step 3>
Double-click [Link] in the folder of defrosted
ZJ00684-100 and install Fuji FILM DSC Jig Driver as
follows.

<Step 4>
Install the software in [C:\ProgramFiles\Fjig] according to the
instructions on the PC's screen.

3-5
 Confidential: FUJIFILM Service Center Use Only

X-Pro1 Service Manual

3-5-2. Various downloading software decompressions, preservation methods, and notes

The PC adjustment softwares are in a specified Web

server, and both of these are the compression of ZIP form
files. Therefore, after downloading these compression files
from the Web server, the decompression of the file is X-Pro1 W PC Soft Ver.*.** ZJ01971-***.zip
necessary. In the decompression software, if the
decompression of the ZIP form can be done, any software
is OK.
(Please prepare each one for the decompression software.)
The decompression and the preservation method of the PC
adjustment software and the firmware are described to the
following.
* The PC adjustment soft decompression and preservation
method

<Step1>
The adjustment software is downloaded from WEB, and
software is installed in the PC.
We have uploaded the “PC Adjustment Software
(ZJ01971-***.zip) for X-Pro1_W” on our website:
([Link]

<Step2>
“ZJ01971-***” is a compression of “ZIP type” file.
The “X-Pro1_W” folder can be done by extracting it by
“Compression software”.
Copy the “X-Pro1_W” folder to the “C” drive on the
Adjustment PC.

<Step 3>
Double-click the "Setup_X-Pro1_W_***.exe" adjustment
software installer file contained in the expanded
ZJ01971-*** folder.

<Step 4>
When the window shown on the right appears, click [Next].

<Step 5>
When the window shown on the right appears, click [Install].
(Installation then begins.)

3-6
 Confidential: FUJIFILM Service Center Use Only

X-Pro1 Service Manual

<Step 6>
When installation ends and the window shown on the
right appears, click [Finish].

3-5-3. Uninstalling X-Pro1 W PC Soft Ver.*.**

<Step 1>
Click : Start
↓
Programs
↓
FUJIFILM REPAIR SERVICE
↓
X-Pro1_W Adjustment Software
↓
Uninstall X-Pro1_W Adjustment Software

<Step 2>
When the window shown on the right appears, click [Yes].
(Uninstallation then begins.)

<Step 3>
When uninstallation ends and the window shown on the
right appears, click [OK].

* In some cases, uninstalling the software does not

remove all the files. To completely remove all the files,
delete the C:\X-Pro1_W folder after completing the
uninstallation.

3-7
 Confidential: FUJIFILM Service Center Use Only

X-Pro1 Service Manual

3-5-4. X-Pro1 SD BOOT card making

The SD BOOT softwares are in a specified Web server, and

both of these are the compression of ZIP form files.
Therefore, after downloading these compression files from
the Web server, the decompression of the file is necessary.
In the decompression software, if the decompression of the
ZIP form can be done, any software is OK.
(Please prepare each one for the decompression software.)
The decompression and the preservation method of the PC
adjustment software and the firmware are described to the
following.
* The PC adjustment soft decompression and preservation
method

<Step1>
Do format of SD card in a “FAT32” form.
Note:All data is erased when do Format of SD card.

(1) Insert the SD card to the card reader.

(2) Open My Computer.

(3) Display a right-click menu of The card reader

(Removable Disk).
(4) Choose Format among menu.

(5) Format window opens.

(6) Choose "FAT32" among "File system".
(7) Push "Start" button.
(8) Format starts.

3-8
 Confidential: FUJIFILM Service Center Use Only

X-Pro1 Service Manual

<Step2>
The SD BOOT software is downloaded from WEB.
We have uploaded the “SD BOOT Software X-Pro1 SD BOOT Soft ZJ01970-***.zip
(ZJ01970-***.zip) for X-Pro1” on our website:
([Link]

<Step3>
“ZJ01970-***” is a compression of “ZIP type” file.
The “X-Pro1 SD BOOT Soft” folder can be done by
extracting it by “Compression software”.
Copy the “X-Pro1 SD BOOT Soft” folder to the “C” drive
on the Adjustment PC.

<Step4>
Copy the “[Link]” file and “[Link]” file, which are
stored in the extracted “X-Pro1 SD BOOT Soft” folder,
under SD card.
Copy the “LX10RCS***.bin” file, which are stored in the
extracted “X-Pro1_W\SCRIPT\LX10\Firmware” folder,
rename to “[Link]” under SD card.

My Computer

3.5inch FD(A:)
(C:)
X-Pro1 SD BOOT Soft
[Link] My Computer
[Link] 3.5inch FD(A:)
(C:)
<X-Pro1 SD BOOT Soft> Removable disk
[Link]

[Link]
My Computer
[Link]
3.5inch FD(A:)
(C:) <X-Pro1 SD card(BOOT only)>
X-Pro1_W
SCRIPT
LX10
･Flash Adjustment
Firmware
LX10RCS***.bin

<X-Pro1 W PC Soft>

3-9
 Confidential: FUJIFILM Service Center Use Only

X-Pro1 Service Manual

3-6. QR Code reader（ZJ01134-100） Setup

Initialize the QR code reader used to carry out the LENS DATA read.

1. Connect the QR code reader to the USB port on the

PC.
2. Wait until the PC recognizes the QR code reader (the
QR code reader emits a beep).
3. Use the QR code reader to scan in the "Add CR
Suffix" provided in "Suffix Selection" in the instruction
manual supplied with the QR code reader.
4. Scanning method
(1) Hold the "Add CR Suffix" bar code so that it is lit
by the aiming beam of the QR code reader (at a
distance of around 5 cm).
(2) Press the switch on the QR code reader.

* The instruction manual is provided in several languages. Add CR Suffix

Use the section provided in any language for the setting.
* Refer to the instruction manual for detailed information on
using the QR code reader.

3-7. Using the Adjustment Software

Menu Command Details
Application Exit (Alt+F4) Terminate HyperFFW
Script Open Do not use
Load Do not use
Execute Do not use
Pause Do not use
About (Ctrl+A) Cancels execution
Edit Do not use
Mode Do not use
Watch variables Do not use
Tool Do not use
Option Do not use
Help Do not use

It is only possible to exit HyperFFW when the "x" circled in

red can be clicked.

To exit HyperFFW during the adjustment, select About

(Ctrl+A) and then select Exit (Alt+F4).

3-10
 Confidential: FUJIFILM Service Center Use Only

X-Pro1 Service Manual

3-8. Launching the Adjustment Software

3-8-1. Launching the Adjustment Software when MAIN PWB Initialize

<Step 1>
Start
↓
Programs
↓
FUJIFILM REPAIR SERVICE
↓
X-Pro1_W Adjustment Software
↓
X-Pro1_W（BOOT）

The adjustments are the same whichever option is selected.

<Step 2>
If adjustment stops at the window shown on the right, press
the [Enter] key to proceed.

<Step 3>
[Repair site ID input] Repair site ID input
The first time the adjustment software is launched, a window
0: SAPPORO A: USA F: BRITAIN Z: OTHERS
appears where you select the repair site ID recorded in the 2: KURIHARA B: CANADA G: GERMANY
camera during End Setting. 3: TOKYO C: HAWAII H: FRANCE
I: SPAIN
In this window, select the appropriate repair site. 5: OSAKA D: TAIWAN J: ITALY
8: FUKUOKA T: CHINA K: NETHERLANDS
E.g.: USA -> Press "A" on the keyboard. Q: SINGAPORE L: BELGIUM
M: SWEDEN
* Once this has been set, this window no longer appears on N: SWITZERLAND
the PC. O: NORWAY
P: FINLAND
* To reset the repair site ID, exit the adjustment software and
then delete C:\X-Pro1_W\[Link].

3-11
 Confidential: FUJIFILM Service Center Use Only

X-Pro1 Service Manual

<Step 4>
[Adjustment Software Start-up Screen]
Check the details and then press the [Enter] key to proceed.

X-Pro1_W Adjustment Software Start-up Screen

Press the [Enter] key.

----＞The adjustment software starts.

<Step 5>
[Notes on using the adjustment software] Cautions When Using the X-Pro1_W Adjustment Software
1. Check the adjustment sequence needed when parts are 1. Adjust as follows after replacing parts.
replaced. [F1]Battery [F4]CMOS Data [F5]Camera [F9]MOUNT
[F8]Firmware Download [F12]End Setting
2. When the MAIN PWB ASSY has been replaced, carry [E]EVF [L]Level(Normal temperature) [H]Level(High temperature)
out the "MAIN PWB Initialize [I]" procedure before [I]MAIN PWB Initialize
starting the adjustment. |--------------------------------------------------------------------------------------------------------|
3. If you have used the adjustment software, always carry | Replaced Parts Adjustment Procedure |
| MAIN PWB : [I]->[F9]->[L]->[F4]->[F5]->[H]->[E]->[F1]->[F12] |
out End Setting. | UNIT MOUNT : [F9]->[L]->[F4]->[F5]->[H]->[E]->[F1]->[F12] |
4. Refer to the Service Manual for precautions and other |--------------------------------------------------------------------------------------------------------|
detailed information on adjustment. 2. When the MAIN PWB ASSY has been replaced, always
MAIN PWB Initialize before making any other adjustments.
3. Always run End Setting after using this adjustment software.
Check the details and then press the [Enter] key to proceed. 4. Proceed with adjustment after reading the cautions here,
and the relevant cautions noted in the Service Manual.
Press the [Enter] key to proceed to the Jig Mode Setup screen.

<Step 6>
[BOOT Mode Setup Screen] X-PRO1 BOOT Mode Setup Screen
For other adjustments, use the "NP-W126 Battery jig " and
Set the BOOT mode by using [DC COUPLER CP-W126 (AC Adapter (9.0V))]
supply power from the regulated power supply so that [7.20V
(+0.02V/-0.00V)] is displayed on the digital voltmeter.
(1) Connect the camera to the PC using the "USB cable".
1) Connect the [USB cable].
(2) Supply power to the camera. 2) Supply power to the camera.
3) Switch camera power ON while pressing the shutter button and up key.
(3) Switch camera power ON while pressing the shutter 4) Ensure that the LED is lit.
button and up key(I).
(4) Check that the LED is lit green When steps 1 to 4 are complete, press the [Enter] key on the PC.

After completing steps (1) to (4), press the [Enter] key to

proceed.

<Step 7>
[MAIN PWB Initialize Screen]
(1) Pressing the [X]:Restart key interrupts the adjustment X-Pro1_W Initialize Screen
software and returns you to the [Adjustment Software
Start-up Screen].
However, the camera will not be recognized as a PTP or
［Ｉ］ : MAIN PWB Initialize
Mass Storage device. *Only use for when the MAIN PWB has been replaced.
(Press the [X] key while the camera is in communication
with the PC. If you press the [X] key while the camera is
disconnected, the [Adjustment Software Start-up Screen]
may be slow to reappear and an error may appear in the
adjustment software.)

[X] : Restart

Revised:[Link].2012

3-12
 Confidential: FUJIFILM Service Center Use Only

X-Pro1 Service Manual

3-8-2. Launching the Adjustment Software other then [I]:MAIN PWB Initialize

[Adjustment environment and precautions]

• When "OK" and "NG" window is displayed and adjusts the same camera again, switch camera power off once, and please
switch camera power on with a jig mode again.

<Step 1>
Click : Start
↓
Programs
↓
FUJIFILM REPAIR SERVICE
↓
X-Pro1_W Adjustment Software
↓
X-Pro1_W

The adjustments are the same whichever option is

selected.

<Step 2>
If adjustment stops at the window shown on the right, press
the [Enter] key to proceed.

<Step 3>
[Repair site ID input] Repair site ID input
The first time the adjustment software is launched, a
0: SAPPORO A: USA F: BRITAIN Z: OTHERS
window appears where you select the repair site ID 2: KURIHARA B: CANADA G: GERMANY
recorded in the camera during End Setting. 3: TOKYO C: HAWAII H: FRANCE
5: OSAKA I: SPAIN
In this window, select the appropriate repair site. D: TAIWAN J: ITALY
8: FUKUOKA T: CHINA K: NETHERLANDS
E.g.: USA -> Press "A" on the keyboard. Q: SINGAPORE L: BELGIUM
M: SWEDEN
* Once this has been set, this window no longer appears on N: SWITZERLAND
the PC. O: NORWAY
P: FINLAND
* To reset the repair site ID, exit the adjustment software
and then delete C:\X-Pro1_W\[Link].

3-13
 Confidential: FUJIFILM Service Center Use Only

X-Pro1 Service Manual

<Step 4>
[Adjustment Software Start-up Screen]
Check the details and then press the [Enter] key to proceed.

X-Pro1_W Adjustment Software Start-up Screen

Press the [Enter] key.

----＞The adjustment software starts.

<Step 5>
[Notes on using the adjustment software] Cautions When Using the X-Pro1_W Adjustment Software
1. Check the adjustment sequence needed when parts are 1. Adjust as follows after replacing parts.
replaced. [F1]Battery [F4]CMOS Data [F5]Camera [F9]MOUNT
[F8]Firmware Download [F12]End Setting
2. When the MAIN PWB ASSY has been replaced, carry [E]EVF [L]Level(Normal temperature) [H]Level(High temperature)
out the "MAIN PWB Initialize [I]" procedure before [I]MAIN PWB Initialize
starting the adjustment. |--------------------------------------------------------------------------------------------------------|
3. If you have used the adjustment software, always carry | Replaced Parts Adjustment Procedure |
| MAIN PWB : [I]->[F9]->[L]->[F4]->[F5]->[H]->[E]->[F1]->[F12] |
out End Setting. | UNIT MOUNT : [F9]->[L]->[F4]->[F5]->[H]->[E]->[F1]->[F12] |
4. Refer to the Service Manual for precautions and other |--------------------------------------------------------------------------------------------------------|
detailed information on adjustment. 2. When the MAIN PWB ASSY has been replaced, always
MAIN PWB Initialize before making any other adjustments.
3. Always run End Setting after using this adjustment software.
Check the details and then press the [Enter] key to proceed. 4. Proceed with adjustment after reading the cautions here,
and the relevant cautions noted in the Service Manual.
Press the [Enter] key to proceed to the Jig Mode Setup screen.

<Step 6>
[Jig Mode Setup Screen] X-PRO1 Jig Mode Setup Screen
(1) When carrying out Battery Voltage Adjustment, use the (1) Set the Jig mode by using [NP-W126 Battery jig (7.2V)]
"NP-W126 Battery jig" and a regulated power supply set at Battery Voltage Adjustment.
(2) Set the Jig mode by using [DC COUPLER CP-W126 (AC Adapter (9.0V))]
to 7.2 V. at adjustments other than Battery Voltage Adjustment.
(2) For other adjustments, use the "NP-W126 Battery jig"
and supply power from the AC adapter (9V). 1) Connect the [USB cable].
2) Supply power to the camera using the jig
as appropriate for the adjustment details.
1. Connect the camera to the PC using the “USB cable”. 3) Switch camera power ON while pressing the shutter button and up key.
4) Ensure that the Led is lit.
2. Use the appropriate jig according to the adjustment
options to supply power. When steps 1 to 4 are complete, press the [Enter] key on the PC.
3. Turn the camera on while holding down the shutter
button and up key(I).
4. Check that the LED is lit green.

After completing steps 1 to 4, press the [Enter] key to

proceed.

Revised:[Link].2012

3-14
 Confidential: FUJIFILM Service Center Use Only

X-Pro1 Service Manual

<Step 7>
[Displaying the firmware version]
If a firmware upgrade is required, separate instructions will Firmware＝1.98
be provided.
Check the details and then press the [Enter] key to proceed. Vendor Name = FUJIFILM
Manufacturer = FUJIFILM
ProductName = X-Pro1
Device Type = CAMERA
SerialNo = 593130323431000000000000000000
Frame Work = 1.00

Please download a new version if it is necessary

to download the firmware.
Advance to the adjustment item selection screen
when press the [Enter] Key of PC.

* If the camera's firmware is an older version than the

firmware in the adjustment software, the window shown on
the right appears. Check the details and then press the
[Enter] key to proceed.

<Step 8> Firmware is latest version

[Adjustment item select screen] X-Pro1_W adjustment item select screen
(1) A firmware download may require other adjustments
depending on the firmware version downloaded. If you 1.[F 9] : MOUNT Data Write
download firmware, separate instructions will be provided 2.[ L ] : Level Adjustment(Normal temperature)
3.[F 4] : CMOS Defect Correction
for the adjustments required when the firmware is 4.[F 5] : Camera Adjustment
upgraded. 5.[ H ]
6.[ E ]
: Level Adjustment(High temperature)
: EVF Adjustment
(2) When you have launched the adjustment software and 7.[F 1] : Battery Voltage Adjustment
8.[F12] : End Setting
exchanged data with the camera, you must carry out End [F 8] : Firmware Download
Setting as the final step before returning the camera to
the customer. [Execute this item only when
Need to change the firmware.]
If you omit End Setting, the camera remains in JIG mode
(camera repair mode) and will not be recognized by the
PC (as a PTP or Mass Storage device) when the [X] : Restart
customer connects the camera to a PC in normal
operation.
(3) Pressing the [X]:Restart key interrupts the adjustment
software. After the "OK" screen display, returns you to
the [Adjustment Software Start-up Screen].
(When adjust the same camera again, switch camera
power off once, and please switch camera power on with
a jig mode again.)
However, the camera will not be recognized as a PTP or
Mass Storage device.
(Press the [X] key while the camera is in communication
with the PC. If you press the [X] key while the camera is
disconnected, the [Adjustment Software Start-up Screen]
may be slow to reappear and an error may appear in the
adjustment software.)

* If the camera's firmware is an older version than the

Firmware is not latest version
firmware in the adjustment software, the "Firmware is not X-Pro1_W adjustment item select screen
latest version" message appears in red in the top-left corner
of the window.
1.[F 9] : MOUNT Data Write
If the firmware is the latest version (or the same as the 2.[ L ] : Level Adjustment(Normal temperature)
adjustment software version), "Firmware is latest version" is 3.[F 4]
4.[F 5]
: CMOS Defect Correction
: Camera Adjustment
displayed in blue. 5.[ H ] : Level Adjustment(High temperature)
6.[ E ] : EVF Adjustment
7.[F 1] : Battery Voltage Adjustment
8.[F12] : End Setting
[F 8] : Firmware Download

[Execute this item only when

Need to change the firmware.]

[X] : Restart

3-15
 Confidential: FUJIFILM Service Center Use Only

X-Pro1 Service Manual

3-9. [I]:MAIN PWB Initialize

[Adjustment environment and precautions]
• When the MAIN PWB ASSY has been replaced, always carry out the "MAIN PWB Initialize" procedure before performing any
other adjustments. The adjustments cannot be made correctly without first carrying out the "MAIN PWB Initialize" procedure.
• Use the SD card (for BOOT).
• If you carry out the "MAIN PWB Initialize" procedure when the MAIN PWB ASSY has not been replaced, all adjusted data will
be reset to the default settings. In this event, carry out all the adjustments (excluding Firmware Download).
• Because the internal memory is formatted during the "MAIN PWB Initialize" procedure, take particular not to erase customer
data when working on repair products.

[Required items]
SD card(BOOT only) Copy ZJ01970-100 and Firmware to SD card
NP-W126 Battery jig ZJ01936-100

<Settings for MAIN PWB Initialize>

NP-W126 Battery Jig

<Step 1>
[Firmware Download]
(1) Insert the SD card(BOOT only) to the card slot.
(2) Connect Power cable (or jig).
(3) Switch camera power ON while pressing the Fn button and Command lever .
(4) Ensure that the LED. [GREEN blinking] -> [RED lighting] -> [ORANGE lighting] -> [RED/GREEN blinking] -> [GREEN
lighting]
(5) Turn the camera off.
(6) Remove the Power cable (or jig) from the camera.
(7) Remove the SD card from the camera.
*Does not USB cable during Firmware Download.

Revised:[Link].2012

3-16
 Confidential: FUJIFILM Service Center Use Only

X-Pro1 Service Manual

<Step 2>
(1) Connect Power cable (or jig).
(2) Connect the camera to the PC using the “USB cable”.
(3) Switch camera power ON while pressing the shutter button and up key.

In the adjustment item select screen, select [I]:MAIN PWB Initialize.

<Step 3>
[Checking MAIN PWB Initialize] MAIN PWB Initialize
Implementation details
Always carry out this step if the MAIN PWB ASSY has been
(1) Reset the flash ROM and format the internal memory. replaced.

[Implementation details]
Press the [Y] key to begin "MAIN PWB Initialize".
Press the [C] key to cancel the procedure. 1. Reset the flash Rom and
Format the internal memory.

[Y] - - -> Proceed to [MAIN PWB Initialize]

[C] - - -> Cancel.

<Step 4>
[Ending MAIN PWB Initialize] MAIN PWB Initialize
(1) Turn the camera off.
MAIN PWB Initialize is completed.
(2) Remove the Power cable (or jig) from the camera.
(3) Remove USB cable from the camera. (1) Turn off power switch.
(4) Press the [Enter] key. (2) Remove the Power cable (or jig) from the camera.
(3) Remove USB cable from the camera.
(4) Press the [Enter] key.
Press the [Enter] key to return to the Adjustment Software
Start-up Screen.

[Enter] -> Return to Start-Up Screen.

3-17
 Confidential: FUJIFILM Service Center Use Only

X-Pro1 Service Manual

3-10. [F9]:Mount Data Write

[Adjustment environment and precautions]
• Do not vibrate the camera during adjustment.

[Required items]
Camera fixing jig If there are no problems with the adjustment environment, a tripod or X-Y
stage can be used.
Mount data for X-Pro1 ZJ01979-100
NP-W126 Battery jig ZJ01936-100

[Method of acquiring MOUNT data]

MOUNT data is required when the CONST ASSY FRONT or MOUNT No.
UNIT MOUNT or Y-10241MAIN PWB ASSY is replaced. 7000051

1. When you exchange UNIT MOUNT

--> It is attached to UNIT MOUNT.

2. When you exchange CONST ASSY FRONT or

Y-10241MAIN PWB ASSY
--> Creating a MOUNT data floppy disk when the CONST
ASSY FRONT or Y-10241MAIN PWB ASSY has been
replaced.
* The following example assumes the use of the serial
No. shown at right.

<Step 1>
Read the serial number of UNIT MOUNT.
The numbers shown at right are as follows.
7000051(7 digits)
The name of the MOUNT data file containing this number is
“[Link]”.

Cautions:
1. The MOUNT data file extension is “txt”. Depending
upon Windows settings, this extension may not be
displayed. In this case, change the settings to ensure that
it is displayed.
2. In addition to numbers, letters are also used in the
MOUNT serial No. The data file name is instructed in the
same manner in this case.
3. Ensure that the MOUNT serial No. is read correctly. If the
file name is read incorrectly MOUNT data for another
camera will be loaded when this file is used.

<Sample image>

Revised:[Link].2012

3-18
 Confidential: FUJIFILM Service Center Use Only

X-Pro1 Service Manual

<Step 2>
Download the ZIP file of top four digits from Web server ([Link]
Open [ZJ01979-100] in the LENS data folder, and download “LX10Mount_7000.zip”.

<Step 3>
Decompress “LX10Mount_7000.zip”.
--> “[Link]” is made.

<Step 4>
Insert a writable floppy disk into the floppy disk drive on the computer.

<Step 5>
Search for “[Link]”, and copy it onto the floppy disk.
Caution: Do not create a folder on the floppy disk when copying the data.

● *When you do not use the floppy disk, you can do the following way.

<Step 4>
Confirm the following folder on C drive.
C:\X-Pro1_W\MOUNT_DATA

<Step 5>
Search for “[Link]”, and copy it onto the folder “C:\X-Pro1_W\MOUNT_DATA”.

<Step 6>
Select [F9]:Mount Data Write in the adjustment item select Mount Data Write
screen.
<Preparations>
Mount the camera on a tripod.
<Step 7>
[Preparing the Mount Data Write]
Mount the camera on a tripod.

When you have completed the preparations, press the [Enter] When preparation is complete,
press the [Enter] key on the PC.
key to proceed. Take care not to vibrate the camera during
subsequent adjustment. -->The lens is extended when the [Enter] key is pressed.

<Step 8>
[Lens number input]
(1) Enter the 7-digit Mount number of camera in the input
box.

● *When you do not use the floppy disk, you can skip (2).

(2) Insert the floppy disk containing the Mount data into the
floppy disk drive.

When you have completed the preparations, press the [Enter]

key to proceed.

<Step 9>
[Ending Mount Data Write]

After completing the adjustments, press the [Enter] key to

proceed. The adjustment item select screen reappears.

Mount Data Write is completed.

Press the [Enter] key to return
to the Adjustment Items Select Screen.

Revised: [Link].2012

3-19
 Confidential: FUJIFILM Service Center Use Only

X-Pro1 Service Manual

3-11. [L]:Level Adjustment(Normal temperature)

[Adjustment environment and precautions]
• Adjust the lighting to give a brightness of 9.0 to 11.0 EV on the Level chart surface..
• Because the likelihood of adjustment failure increases as the internal camera temperature rises, when adjustment fails you
should first try turning the camera off for a while and then carrying out the adjustment again.
• When removing / mounting jig lens, please note the dust from entering.

[Required items]
Camera fixing jig If there are no problems with the adjustment environment, a tripod or X-Y
stage can be used.
Lighting Illuminate the chart
FxHS20EXR/X100 Level Chart ZJ01849-100
X-Pro1 Level jig ZJ01935-100
Rotation axis Stand ZJ01858-100
NP-W126 Battery jig ZJ01936-100
FUJINON LENS XF18mm F2 R ---
Laser telemeter Marketing product. Please purchase it in a general merchandising store.
Maker : Makita, Model : SK308PZ
When it's following specification equal to "SK308PZ", the Laser telemeter
container is practicable.
･Precision : ±1mm/10m
･Line Point laser : X direction/Y direction

<Settings for Level Adjustment>

Y direction
Lighting
Level Chart
Camera

Center X direction

＜Line Point laser movement of Laser telemeter＞

This gray section is the

“lens-face”.
500±10mm

<Settings for Level Chart>

Adjust it in the following procedure at the time of "Level jig

zero degree" so that "Level Chart" becomes level.

(1) Setting Rotation Stand in the horizontal place.

(2) Setting of Level jig in Rotation Stand. Setting of Level jig
at the time of "0 degrees" to become level.
(3) Adjust the positions so that the distance from the level
chart to the camera's lens-face is 500 +-5 mm.
(4) The Chart center comes to the LCD center.
(5) Setting Laser telemeter in the horizontal place.
(6) Irradiate Line Point in Chart from telemeter.
(7) Turn Chart to Line Point.
(8) The chart center confirms a thing in the LCD center.

Rotation Stand Level jig

Level Chart

Revised:[Link].2012

3-20
 Confidential: FUJIFILM Service Center Use Only

X-Pro1 Service Manual

<Step 1>
In the adjustment item select screen, select [L]: Level Adjustment(Normal temperature).

<Step 2>
[Preparing for Level Adjustment(Normal temperature)] Level Adjustment(Normal temperature)
(1) Prepare the Level chart.
(2) Mount the camera on the Level jig so that it is facing the (1) Prepare a Level chart (1000mm x 700mm or more)..
level chart. (2) Set the camera in the [Level Jig]..
(3) Set the distance between the camera and
(3) Adjust the positions so that the distance from the level the Level chart to 500 +-5mm
chart to the camera's lens-face is 500 +-5 mm.
When the camera temperature is less than 30 degrees, adjust it.

When you have completed the preparations, press the [Enter]

key to proceed.
When preparations (1) - (3) are complete,
press the [Enter] key on the PC.

--> The lens is extended when the [Enter] key is pressed.

<Step 3>
[Level Adjustment(Normal temperature) initialization] Level Adjustment(Normal temperature)
(1) Set the camera and Level chart to designated distance. (1) Adjust the position of the camera so that the center of
the Level chart is displayed in the camera LCD.

When you have completed the preparations, press the [Enter] When preparations (1) is complete,
press the [Enter] key.
key to proceed.

A = 500 +-5mm

<Step 4>
(1) Set the Level jig in 0 degree.
Set up the posture of the camera in the angle of 0 degree.

When you have completed the preparations, press the [Enter]

key to proceed.

Press the [Enter] key.

3-21
 Confidential: FUJIFILM Service Center Use Only

X-Pro1 Service Manual

<Step 5>
(1) Set the Level jig in 20 degree.
Set up the posture of the camera in the angle of 20 degree.

When you have completed the preparations, press the [Enter]

key to proceed.

Press the [Enter] key.

<Step 6>
(1) Set the Level jig in 70 degree.
Set up the posture of the camera in the angle of 70 degree.

When you have completed the preparations, press the [Enter]

key to proceed.

Press the [Enter] key.

<Step 7>
(1) Set the Level jig in 90 degree.
Set up the posture of the camera in the angle of 90 degree.

When you have completed the preparations, press the [Enter]

key to proceed.

Press the [Enter] key.

3-22
 Confidential: FUJIFILM Service Center Use Only

X-Pro1 Service Manual

<Step 8>
(1) Set the Level jig in 270 degree.
Set up the posture of the camera in the angle of 270 degree.

When you have completed the preparations, press the [Enter]

key to proceed.

Press the [Enter] key.

<Step 9>
[Ending Level Adjustment(Normal temperature)]

After completing the adjustments, press the [Enter] key to

proceed.
The adjustment item select screen reappears.

Level Adjustment(Normal temperature) is completed

Press the [Enter] key to return
to the Adjustment Items Select Screen.

3-23
 Confidential: FUJIFILM Service Center Use Only

X-Pro1 Service Manual

3-12. [F4]:CMOS Defect Correction

[Adjustment environment and precautions]
• Darken the surroundings during adjustments (a darkroom environment is ideal). Alternatively, prepare a box that is painted
black on the inside and perform the adjustments with the camera enclosed in the box. Please be careful so that a fluorescent
light does not enter.
• Darken the surroundings as much as possible for the adjustments.
• Do not vibrate the camera during adjustment.
• Because the likelihood of adjustment failure increases as the internal camera temperature rises, when adjustment fails you
should first try turning the camera off for a while and then carrying out the adjustment again.
• Check that Level Adjustment(Normal temperature) have finished.
• When removing / mounting jig lens, please note the dust from entering.

[Required items]
Camera fixing jig If there are no problems with the adjustment environment, a tripod or X-Y
stage can be used.
PTB450F Pattern box
LB145 filter ZJ00699-100
NP-W126 Battery jig ZJ01936-100
FUJINON LENS XF35mm F1.4 R ---

<Use the pattern box for Camera adjustment>

Turn on the power supply in the pattern box.
Afterwards, wait for about ten minutes so that the source of light may stabilize.

(1) Brightness
160 ± 5cd/m2 (with LB145 filter)
No chart, center of pattern box
Minolta brightness meter LS-110 or equivalent
* Calibration method
Place the filter (LB145) against the pattern box. With
the filter (LB145) in contact with the brightness meter,
adjust the pattern box brightness to 160 ± 5cd/m2.

(2) Color temperature

6100 ± 50K (with LB145 filter)
No chart, center of pattern box
Minolta color meter IIIF or equivalent
* Calibration method
Place the filter (LB145) against the pattern box. With
the filter (LB145) in contact with the color temperature
meter, adjust the pattern box color temperature to 6100
Calibration method of pattern box
± 50K.

<Step 1>
Select [F4]: CMOS Defect Correction in the adjustment item select screen.

<Step 2>
[Preparing the CMOS Defect Correction pattern box] CMOS Defect Correction
<Preparations>
(1) Stick the LB145 filter in the center of the pattern box.
(2) Use a color temperature meter to set the color (1) Prepare the LB145 filter.
temperature to 6100 ± 50K. (2) Adjust the color temperature of the pattern box (PTB450)
to 6100+-50K.
(3) Use a luminance meter to set the luminance to 160 ± 5 (3) Adjust the luminance of the pattern box (PTB450)
to 160+-5cd/m2.
cd/m2. (4) Fix the camera on a tripod and set it in front of the
* Because adjustments to one setting will skew the other pattern box.

setting, the color temperature and luminance should be

When preparations (1) - (4) are complete,
cross-checked a number of times. (Repeat steps 2 and 3 press the [Enter] key on the PC.
several times.) - - > Lens is extended when the [Enter] key is pressed.
(4) Remove the LB145 filter and fix the camera onto the XY
stage or tripod so that it is facing the pattern box.

When you have completed the preparations, press the [Enter]

key to proceed.

Revised:[Link].2012

3-24
 Confidential: FUJIFILM Service Center Use Only

X-Pro1 Service Manual

<Step 3>
[Inspection for S/N main]
Inspection for S/N main

(1) Set the distance between the camera and pattern box.
(2) Place the LB140 filter in front of the lens.

Maximum Maximum When preparations are complete, press the [Enter] key.

6mm 6mm
Camera

Centerline Centerline Pattern box

A = 6mm or less
B = 6mm or less

Filter(LB145)

(1) Set up the camera and the LB145 filter at the specified
distances.
(2) Position the LB145 filter at the designated location in
front of the lens.

When you have completed the preparations, press the [Enter] key to proceed.
Take care not to vibrate the camera during subsequent adjustment.

<Step 4>
[Ending CMOS Defect Correction]
After completing the adjustments, press the [Enter] key to
proceed.
The adjustment item select screen reappears.

CMOS Defect Correction completed

Press the [Enter] key to return
to the Adjustment Items Select Screen.

3-25
 Confidential: FUJIFILM Service Center Use Only

X-Pro1 Service Manual

3-13. [F5]:Camera Adjustment

[Adjustment environment and precautions]
• Darken the surroundings during adjustments (a darkroom environment is ideal). Alternatively, prepare a box that is painted
black on the inside and perform the adjustments with the camera enclosed in the box. Please be careful so that a fluorescent
light does not enter. Please be careful so that a fluorescent light does not enter.
• Calibrate the pattern box before the adjustment.
• Any soiling on the pattern box dispersion plate or reflective plate will result in unevenness in the lighting and cause errors
during adjustment. Take care to carry out periodic pattern box cleaning and testing.
• Check that Level Adjustment(Normal temperature) and CMOS Defect Correction have finished.
• When removing / mounting jig lens, please note the dust from entering.

[Required items]
Camera fixing jig If there are no problems with the adjustment environment, a tripod or X-Y
stage can be used.
PTB450F Pattern box
LB145 filter ZJ00699-100
NP-W126 Battery jig ZJ01936-100
FUJINON LENS XF35mm F1.4 R ---

<Settings for Camera Adjustment>

Maximum Maximum
6mm 6mm
Camera

Centerline Centerline Pattern box

Filter(LB145)

<Step 1>
In the adjustment item select screen, select [F5]: Camera Adjustment.

<Step 2>
[Preparing the camera adjustment pattern box] Camera Adjustment
(1) Stick the LB145 filter in the center of the pattern box. <Preparations>
(2) Use a color temperature meter to set the color
temperature to 6100 ± 50K. (1) Prepare the LB145 filter.
(2) Adjust the color temperature of the pattern box (PTB450)
(3) Use a luminance meter to set the luminance to 160 ± 5 to 6100+-50K.
cd/m2. (3) Adjust the luminance
to 160+-5cd/m2.
of the pattern box (PTB450)

* Because adjustments to one setting will skew the other (4) Fix the camera on a tripod and set it in front of the
pattern box.
setting, the color temperature and luminance should be
cross-checked a number of times. (Repeat steps 2 and 3
several times.) When preparations (1) - (4) are complete,
press the [Enter] key on the PC.
(4) Remove the LB145 filter and fix the camera onto the XY
-->Lens is extended when the [Enter] key is pressed.
stage or tripod so that it is facing the pattern box.

When you have completed the preparations, press the [Enter]

key to proceed.

Revised:[Link].2012

3-26
 Confidential: FUJIFILM Service Center Use Only

X-Pro1 Service Manual

<Step 3>
[Shutter adjustment] Shutter adjustment main
(1) Set the camera to designated distance.
(1) Set the distance between the camera and pattern box.
(2) Remove the LB145 filter and the R60 filter from front of the lens.
When you have completed the preparations, press the [Enter] When preparations are complete, press the [Enter] key.
key to proceed.

A = 6mm or less
B = 6mm or less

<Step 4>
[Aperture sensitivity decrease rate adjustment] Aperture sensitivity decrease rate adjustment
(1) Position the LB145 filter at the designated location in
(1) Set the distance between the camera and pattern box.
front of the lens. (2) Place the LB145 filter in front of the lens.

When preparations are complete, press the [Enter] key.

When you have completed the preparations, press the [Enter]
key to proceed.

A = 6mm or less
B = 6mm or less

<Step 5>
[WB adjustment (3200K)] WB_3200K_NORMAL
(1) Remove the LB145 filter from the front of the lens.
(1) Set the distance between the camera and pattern box.
(2) Remove the LB145 filter from front of the lens.
When you have completed the preparations, press the [Enter] When preparations are complete, press the [Enter] key.
key to proceed.

A = 6mm or less
B = 6mm or less

<Step 6>
[Ending Camera Adjustment]

After completing the adjustments, press the [Enter] key to

proceed.
The adjustment item select screen reappears.

Camera Adjustment completed

Press the [Enter] key to return
to the Adjustment Items Select Screen.

3-27
 Confidential: FUJIFILM Service Center Use Only

X-Pro1 Service Manual

3-14. [H]:Level Adjustment (High temperature)

[Adjustment environment and precautions]
• Adjust the lighting to give a brightness of 9.0 to 11.0 EV on the Level chart surface.
• Check that Level Adjustment(Normal temperature), AF Adjustment, CMOS Defect Correction and Camera Adjustment have
finished.
• Carry out the Level Adjustment(High temperature) at high temperature more than eight degrees from the Level
Adjustment(Normal temperature), when adjustment fails you should first try turning the camera on a while and then carrying
out the adjustment again.
• When removing / mounting jig lens, please note the dust from entering.

[Required items]
Camera fixing jig If there are no problems with the adjustment environment, a tripod or X-Y
stage can be used.
Lighting Illuminate the chart
FxHS20EXR/X100 Level Chart ZJ01849-100
X-Pro1 Level jig ZJ01935-100
Rotation axis Stand ZJ01858-100
NP-W126 Battery jig ZJ01936-100
FUJINON LENS XF18mm F2 R ---
Laser telemeter Marketing product. Please purchase it in a general merchandising store.
Maker : Makita, Model : SK308PZ
When it's following specification equal to "SK308PZ", the Laser telemeter
container is practicable.
･Precision : ±1mm/10m
･Line Point laser : X direction/Y direction

<Settings for Level Adjustment>

Y direction
Lighting
Level Chart
Camera

Center X direction

＜Line Point laser movement of Laser telemeter＞

This gray section is the
“lens-face”.
500±10mm

<Settings for Level Chart>

Adjust it in the following procedure at the time of "Level jig

zero degree" so that "Level Chart" becomes level.

(1) Setting Rotation Stand in the horizontal place.

(2) Setting of Level jig in Rotation Stand. Setting of Level jig
at the time of "0 degrees" to become level.
(3) Adjust the positions so that the distance from the level
chart to the camera's lens-face is 500 +-5 mm.
(4) The Chart center comes to the LCD center.
(5) Setting Laser telemeter in the horizontal place.
(6) Irradiate Line Point in Chart from telemeter.
(7) Turn Chart to Line Point.
(8) The chart center confirms a thing in the LCD center.

Rotation Stand Level jig Level Chart

Revised:[Link].2012

3-28
 Confidential: FUJIFILM Service Center Use Only

X-Pro1 Service Manual

<Step 1>
In the adjustment item select screen, select [H]: Level Adjustment(High temperature).

<Step 2>
[Preparing for Level Adjustment(High temperature)] Level Adjustment(High temperature)
(1) Prepare the Level chart.
(2) Mount the camera on the Level jig so that it is facing the (1) Prepare a Level chart (1000mm x 700mm or more)..
level chart. (2) Set the camera in the [Level Jig]..
(3) Set the distance between the camera and
(3) Adjust the positions so that the distance from the level the Level chart to 500 +-5mm
chart to the camera's lens-face is 500 +-5 mm.
When the camera temperature is more than normal temperature adjustment.
temperature +8 degree, adjust it.
When you have completed the preparations, press the [Enter]
key to proceed.
When preparations (1) - (3) are complete,
press the [Enter] key on the PC.

--> The lens is extended when the [Enter] key is pressed.

<Step 3>
[Level Adjustment(High temperature) initialization] Level Adjustment(High temperature)
(1) Adjust the position of the camera so that the center of
(1) Set the camera and Level chart to designated distance. the Level chart is displayed in the camera LCD.

When preparations (1) is complete,

When you have completed the preparations, press the [Enter] press the [Enter] key.

key to proceed.

A = 500 +-5mm

<Step 4>
(1) Set the Level jig in 0 degree.
Set up the posture of the camera in the angle of 0 degree.

When you have completed the preparations, press the [Enter]

key to proceed.

Press the [Enter] key.

3-29
 Confidential: FUJIFILM Service Center Use Only

X-Pro1 Service Manual

<Step 5>
(1) Set the Level jig in 20 degree.
Set up the posture of the camera in the angle of 20 degree.

When you have completed the preparations, press the [Enter]

key to proceed.

Press the [Enter] key.

<Step 6>
(1) Set the Level jig in 70 degree.
Set up the posture of the camera in the angle of 70 degree.

When you have completed the preparations, press the [Enter]

key to proceed.

Press the [Enter] key.

<Step 7>
(1) Set the Level jig in 90 degree.
Set up the posture of the camera in the angle of 90 degree.

When you have completed the preparations, press the [Enter]

key to proceed.

Press the [Enter] key.

<Step 8>
[Ending Level Adjustment(High temperature)]

After completing the adjustments, press the [Enter] key to

proceed.
The adjustment item select screen reappears.

Level Adjustment(High temperature) is completed

Press the [Enter] key to return
to the Adjustment Items Select Screen.

3-30
 Confidential: FUJIFILM Service Center Use Only

X-Pro1 Service Manual

3-15. [E]:EVF Adjustment

[Adjustment environment and precautions]
• Use an AC cable to supply power to the sensor on the LCD adjustment jig.

[Required items]
Camera fixing jig If there are no problems with the adjustment environment, a tripod or X-Y
stage can be used.
LCD adjustment jig ZJ00585-100
(The cable must be connected to a PCI-2747A board installed in a PC.)
LCD JIG COVER ZJ00631-100 (attach to the sensor to block the light)
NP-W126 Battery jig ZJ01936-100

<Settings for EVF Adjustment>

5±2mm

Camera
LCD adjustment jig

PC for adjustments and checks

X-Pro1

PC2747

AC-5V

USB cable

NP-W126 Battery jig Regurated

Digital voltmeter Power supply
USB

Revised:[Link].2012

3-31
 Confidential: FUJIFILM Service Center Use Only

X-Pro1 Service Manual

<Step 1>
In the adjustment item select screen, select [F3]:EVF Adjustment.

<Step 2>
[Preparing for EVF Adjustment] EVF Adjustment
(1) Turn the camera off.
(1) Turn off power switch.
(2) Unplug the power cord from the camera. (2) Remove the Power cable (or jig) from the camera.
(3) Plug the power cord back into the camera. (3) Reconnect Power cable (or jig).
(4) Switch camera power ON.
(4) Turn the camera on. (5) Press the [Enter] key after green LED lights on.
(5) Check that the LED is lit green and then press the [Enter]
key.

When you have completed the preparations, press the [Enter]

key to proceed.
When preparations (1) - (5) are complete
press the [Enter] key on the PC..

<Step 3>
[Preparing for EVF Adjustment] EVF Adjustment
(1) Supply power to the sensor from the AC adapter and
< Preparations >
align the sensor so that it is in the EVF screen and all (1) Attach the sensor of the EVF adjustment jig
external light is excluded. to the center of the EVF monitor.

(2) Ensure that the periphery is as dark as possible.

When you have completed the preparations, press the [Enter]
key to proceed. When preparations (1) - (2) are complete
press the [Enter] key on the PC..

A = 5 +-2mm

<Step 4>
[Ending EVF Adjustment]

After completing the adjustments, press the [Enter] key to

proceed.
The adjustment item select screen reappears.

EVF Adjustment is completed

Press the [Enter] key to return
to the Adjustment Items Select Screen.

3-32
 Confidential: FUJIFILM Service Center Use Only

X-Pro1 Service Manual

3-16. [F1]:Battery Voltage Adjustment

[Adjustment environment and precautions]

• If you have not been using the battery jig up until the immediately preceding adjustment, briefly pause the adjustment
software (press "X" in the adjustment item select screen) and then turn the camera off.
Then set the battery jig as the power supply (set the designated voltage) and then restart the adjustment software.
• Measure the voltage at the battery jig clip position.
• Ensure that the voltage provided by the regulated power supply does not suddenly decrease during adjustment. If the voltage
drops significantly below the designated voltage, the camera turns off, communication between the adjustment software and
the camera is interrupted and an error occurs.

[Required items]
Camera fixing jig If there are no problems with the adjustment environment, a tripod or X-Y
stage can be used.
Regulated power supply
Digital Voltmeter
NP-W126 Battery jig ZJ01936-100

<Settings for Battery Voltage Adjustment>

NP-W126 Battery Jig

3-33
 Confidential: FUJIFILM Service Center Use Only

X-Pro1 Service Manual

<Step 1>
In the adjustment item select screen, select [F1]: Battery Voltage Adjustment.

<Step 2>
[Preparing for Battery Voltage Adjustment] Battery Voltage Adjustment
Launch the adjustment software and connect the PC to the
<Preparations>
camera as shown in the figure before establishing
communication between them. 1. Check that the NP-W126 Battery jig and the camera are connected.
* If not, return to the Jig Mode Setup screen,
and connect the NP-W126 Battery jig and the camera.
* If you are not using the battery jig, briefly pause the 2. Supply power (7.2V) to the camera from
adjustment software (Ctrl+A) and then proceed to the "Jig the [NP-W126 Battery jig].

Mode Setup Screen" in the adjustment software.

Set the digital voltmeter to voltage measurement mode and
then connect the digital voltmeter to the battery jig clip. When preparations are complete, press the [Enter] key on the PC.
Check the digital voltmeter to ensure that the regulated ->Lens is extended when the [Enter] key is pressed.
voltage is set to 7.2V. Then set the camera in the battery jig
and again turn it on in Jig mode. Then proceed to Battery
Voltage Adjustment.

When you have completed the preparations, press the [Enter]

key to proceed.

<Step 3>
[BATT_END] BATT_END
Adjust the voltage from the regulated power supply so that
[6.20V (+0.02V/-0.00V)] is displayed on the digital voltmeter.

When you have completed the preparations, press the [Enter]

Apply an input voltage of 6.20V(+0.02V/-0.00V) in the battery jig.
key to proceed. When preparations are complete, press the [Enter] key.

<Step 4>
[BATT_AC] BATT_AC
Adjust the voltage from the regulated power supply so that
[8.65V(±0.1V)] is displayed on the digital voltmeter.

When you have completed the preparations, press the [Enter]

Apply an input voltage of 8.65V(+0.02V/-0.00V) in the battery jig.
key to proceed. When preparations are complete, press the [Enter] key.

Revised: [Link].2012

3-34
 Confidential: FUJIFILM Service Center Use Only

X-Pro1 Service Manual

<Step 5>
[Restoring the Battery Voltage Adjustment default Battery Voltage Adjustment
voltage]
Adjust the voltage from the regulated power supply so that
[7.20V(±0.1V)] is displayed on the digital voltmeter.
Apply
Applyan
aninput
inputvoltage
voltageofof3.70V(+-0.1V)
7.20V(+-0.1V)ininthe
thebattery
batteryjig.
jig.
When you have completed the preparations, press the [Enter] When
Whenpreparations
preparationsare
arecomplete,
complete,press
pressthe
the[Enter]
[Enter]key.
key.
key to proceed.

<Step 6>
[Ending Battery Voltage Adjustment]

After completing the adjustments, press the [Enter] key to

proceed.
The adjustment item select screen reappears.

Battery Voltage Adjustment is completed

Press the [Enter] key to return
to the Adjustment Items Select Screen.

Revised: [Link].2012

3-35
 Confidential: FUJIFILM Service Center Use Only

X-Pro1 Service Manual

3-17. [F8]: Firmware Download

[Adjustment environment and precautions]
• Carry out a firmware download when instructed to do so.
Depending on the firmware that is upgraded, it may be necessary to make adjustments to the camera or to reset the EEPROM.
• Do not turn the camera off during firmware downloading.
Turning the camera off while a download is in progress could damage the camera. (At worst, it may no longer be possible to
turn the camera on.)

[Required items]
None

<Setting for Firmware Download>

NP-W126 Battery Jig

Revised:[Link].2012

3-36
 Confidential: FUJIFILM Service Center Use Only

X-Pro1 Service Manual

<Step 1>
In the adjustment item select screen, select [F8]: Firmware Firmware Download
Firmware Download
Download.
LED lights to orange while downloading the firmware.
<Step 2> Do not turn off the power while downloading the firmware.

[Checking Firmware Download]

Do not turn the camera off during the firmware download.
The LED on the camera lights orange while the firmware is
downloading.

Press the [Enter] key to begin "Firmware Download".

Press the [C] key to cancel the procedure. [Enter] -> Firmware Download.
[C] - - - - - -> Cancel.

* The figure on the right shows the window displayed during

firmware downloading. Firmware Download
Firmware Download
If firmware downloading ends successfully, the LED lights
green. Downloading...

--> The indicator lamp is lights in green when downloading

is completed normally.

c:\X-Pro1_W\SCRIPT\LX10\Firmware\[Link]

<Step 3>
[Ending Firmware Download] Firmware Download
Firmware Download is completed
(6) Turn the camera off.
(1) Turn off power switch.
(7) Unplug the power cord from the camera. (2) Remove the Power cable (or jig) from the camera.
(8) Plug the power cord back into the camera. (3) Reconnect Power cable (or jig).
(4) Switch camera power ON while pressing the shutter button and up key.
(9) Turn the camera on while holding down the shutter (5) Press the [Enter] key after green LED lights on.
button and up key(I).
(10) Check that the LED is lit green and then press the [Enter]
key.

Press the [Enter] key to begin "Adjustment Value Protection

Reset".
--> Execution [Adjustment value Protection Reset]
after press the [Enter] key.

<Step 4>
[Checking Adjustment Value Protection Reset] Adjust Area Backup Reset
Adjustment value Protection Reset is completed
To apply the firmware, reset the EEPROM while protecting
(1) Turn off power switch.
the adjustment values. (2) Remove the Power cable (or jig) from the camera.
(1) Turn the camera off. (3) Reconnect Power cable (or jig).
(4) Switch camera power ON while pressing the shutter button and up key.
(2) Unplug the power cord from the camera. (5) Press the [Enter] key after green LED lights on.
(3) Plug the power cord back into the camera.
(4) Turn the camera on while holding down the shutter
button and up key(I).
(5) Check that the LED is lit green and then press the [Enter]
key.
--> The adjustment software returns to Start-Up screen
Press the [Enter] key to return to the Adjustment Software after press the [Enter] key.
Start-up Screen.

3-37
 Confidential: FUJIFILM Service Center Use Only

X-Pro1 Service Manual

3-18. [F12]:End Setting

[Details]
• Default camera destinations
The serial number is used as a guide to setting the default destination for a camera.
• USB_ID Write
Every USB device (the camera in this case) must be globally unique as a USB device. To ensure this, the USB standard
requires that a device-specific ID be assigned to each device.
• Switching from repair mode to product mode
This changes the mode from the repair mode (JIG mode) set when the adjustment software is used to product mode (the
mode that allows a PC to recognize the camera as a PTP or Mass Storage device).
• Repair site ID Write
The repair site ID is written to the camera when the adjustment software is first launched. The settings are shown in the
table below. (No setting tasks are included in the End Setting procedure.)

Item Details
Repair Date Date information is acquired from the PC and written.
Administrator ID 01(01)
Repair Station U.S.A. 61(a) SAPPORO 30(0)
CANADA 62(b) KURIHARA 32(2)
HAWAII 63(c) TOKYO 33(3)
TAIWAN 64(d) OSAKA 35(5)
BRITAIN 66(f) FUKUOKA 38(8)
GERMANY 67(g) OTHER 7A(z)
FRANCE 68(h)
SPAIN 69(i)
ITALY 6A(j)
NETHERLANDS 6B(k)
BELGIUM 6C(l)
SWEDEN 6D(m)
SWITZERLAND 6E(n)
NORWAY 6F(o)
FINLAND 70(p)
SINGAPORE 71(q)
CHINA 74(t)
Repair Serial No. A serial No. is assigned automatically and written

[Adjustment environment and precautions]

• The End Setting procedure must always be carried out after adjustment is completed.
If End Setting is omitted, the camera will not be recognized as a PTP or Mass Storage device when it is connected to a PC in
normal operation.

[Required items]
None

3-38
 Confidential: FUJIFILM Service Center Use Only

X-Pro1 Service Manual

<Step 1>
In the adjustment item select screen, select [F12]: End Setting. End Setting

The End settings consist of the destination setting,

<Step 2> the USB_ID write, and product mode settings
[Checking End Setting] (= Mass Storage recognition).

Check the details and then press the [Enter] key to proceed.

Press the [Enter] key.

<Step 3>
[Destination setting] Destination setting
Look at the 3rd digit from the left in the camera's serial number
The destination is selected from an undermentioned list,
and then press the corresponding key. according to third character from left side of the serial number.

The third character

Selected key Destination 3rd digit in serial no. <J> J-model 0 to 8
<U> US-model A to H,J,K
J J-model 0 to 8 <W> E1/EG/EE/RU/AS/EU-model L to N,P to V
<C> CH-model W to Z
U US-model A to H,J,K
W E1/EG/EE/RU/AS/EU-model L to N,P to V
C CH-model W to Z

<Step 4>
[Checking the USB_ID and destination]

Check the details and then press the [Enter] key to proceed.
592D36323831110216E7211Z110001

Selected X-Pro1 J-model.

Press the [Enter] key!

<Step 5>
[Ending Adjustment]
(1) Turn the camera off.
(2) Disconnect the power cord from the camera. X-PRO1 Adjustment completed.
(3) Disconnect the USB cable from the camera.
1) Turn off power switch.
When you have completed these steps, press the [Enter] key. 2) Remove the Power cable (or jig) from the camera.
After the "OK" screen display, the Adjustment Software 3) Remove USB cable from the camera.
Start-up Screen reappears. 4) Press the [Enter] key.
(When adjust the same camera again, switch camera power off
--> The adjustment software returns to Start-Up screen
once, and please switch camera power on with a jig mode After press the [Enter] key.
again.)

3-39
 Confidential: FUJIFILM Service Center Use Only

X-Pro1 Service Manual

MEMO

3-40
 Confidential: FUJIFILM Service Center Use Only

X-Pro1 Service Manual

4. Inspection
4-1. Required Measuring Equipment
Parts number Measuring equipment Remarks
Power supply Regulated power supply
Digital voltmeter For general use
Ammeter For general use (able to measure 1mA or less)
TV Monitor For general use (with terminal HDMI)
HDMI CABLE For general use (Type A-C)
External Flash For general use (able to Synchronization Communication)
FUJINON LENS Commercial accessories
XF35mmF1.4R
 Light viewer Common with FinePix Z800EXR.
* This is commercially available.
Manufacturer: HAKUBA, model numbers: items equivalent to
KLV-5700
ZJ01936-100 NP-W126 Battery jig Common with the adjustment JIG
ZJ00525-100 Macro Chart Resolution confirmation
ZJ00885-100 LCD INSPECTION DATA For LCD inspection (Download from the web)
ZPU0512-100 SD CARD ULTRA2 1GB To check inspection SD recording
ZJ00982-100 Multi Cable(USB/AV) for F30 Common with adjustment JIG
ZJ01848-100 FxX100 Line Chart New JIG
ZJ01988-100 Appearance inspection For finder inspection
sample chart
 ZJ02093-100 X-Pro1 W Dust Inspection CMOS Dust Inspection software
Soft Ver.1.00
 ZS00172-100 Cleaning paper

4-2. Connection of Measuring Equipment

Use the NP-W126 Battery jig.
The output current of the Regurated power supply must not become 2.5A or more.
CAMERA

NP-W126 Battery jig

: Revised
 Revised: [Link].2012
4-1
 Confidential: FUJIFILM Service Center Use Only

X-Pro1 Service Manual

4-3. Inspection and Factory Settings

Measuring
Preparations for adjustment Method of adjustment
Sequence Item Mode equipment
(measurement points, subject, other) (VRs, waveforms, required values)
and jigs
1 External visual (1) Observe the camera. (1) Check for damage to the outer
check casing (Inventory repairs only).
Check for problems with the clicking
or sliding movement of switches.
Check for dust or fogging in the
LCD.
2 Attachment of a (1) Lens mount cover is removed.
lens (2) 35mm Lens is attached. (2) Garbage dose not enter to the inside
of
a lens mount.
3 Power switch P mode (1) Set the power supply voltage. (1) 7.80V±0.10V
check (2) Connect the power supply jig to the ZJ01936-100
battery terminal.
(3) Insert a card. (3) SD card for recording checking. ZPU0512-100
(4) Select the mode dial setting. (4) Mode: IRIS AUTO/SS AUTO.
(5) Turn the camera on.
(6) If a message appears asking for the (6) <DISP/BACK>
language and date to be set, press
the specification button on the right.
(7) Check the LCD screen display (7) Check that the live image and text is
status. displayed.
(8) Check for blemishes in the CMOS (8) Monitor a very bright subject and
live check that the live image does not
image. dim or darken.
4 Shock noise check P mode (1) Apply a shock to the camera using (1) Check for problems on the LCD
in Auto mode the shock jig. monitor.
Check that the camera recovers
from synchronicity disruption.
(Note) Do not apply shocks directly
to the lens or card cover.
5 Leveling instrument P mode (1) Turn on level indication. (1) Push the <DISP/BACK> button and
check choose CUSTOM(C) setting.
(2) The camera is rotated by 90 (2) The indication of the level follow it.
degrees. (3) Push the <DISP/BACK> button and
(3) Turn off level indication. choose STANDERD setting.
6 Image rotate check P mode (1) The camera is rotated by 90
degrees. (2) Rotate image have to be easy to
(2) Press the shutter button to take a understand.
picture.
7 Resolution check P mode (1) Use a macro resolution chart as the ZJ00525-100
Focusing check subject.
(2) Set the camera to Macro mode. (2) The Macro icon ( ) appears on the
LCD monitor.
(3) Set the camera up so that the chart
fills the screen from corner to corner.
(4) Press the shutter button to take a (4) The indicator lamp lights green ->
picture. Intermittently lights orange or green
(recording) -> Turns off.

4-2
 Confidential: FUJIFILM Service Center Use Only

X-Pro1 Service Manual

8 Manual focus check P mode (1) Set the manual focus(MF) mode. (1) Select the MF of a MF/S-AF/C-AF
(2) Turn the focus ring. changeover switch.
(3) Set the AF-S mode. (2) Focus change.
(3) MF indication disappear.
9 External Flash P mode (1) Set the tester’s + probe on the flash
operation check hot shoe X contacts and the
tester's – probe on the flash hot shoe
GND contact.
(2) Press the shutter button to take a (2) Thing which does decrease change by
Picture. resistance momentarily, and returns to
origin immediately.
(3) Turn the External Flash on.
(4) Connect the camera to the External
Flash with the synchronization code.
(5) Press the shutter button to take a (5) An External Flash emits light.
Picture.
(6) Disconnect the synchronization
code from camera.
(7) Turn the External Flash off.
10 Movie/audio Movie mode (1) Set the MOVIE mode.
recording check (2) Press shutter button. (2) Check that movie/audio recording
begins. Check that “REC” appears
on the LCD monitor.
(3) After 5 seconds, press shutter (3) Check that movie/audio recording
button. ends and that the data is recorded
on the SD card.

(4) Set the STILL IMAGE mode.

11 Movie/audio Playback (1) Set the camera to Playback mode.
playback check (2) Press the 4-way button (down) to (2) Check that the movie is played back
play back the movie. on the LCD monitor.
Check that the sound is played back
through the speaker.
12 Playback check Playback (1) Plug the HDMI CABLE into the (1) The LCD displays should switch off,
camera. and the indicator lamp should light
up in green.
(2) Check images shot at macro (2) Where the horizontal resolution is as
resolutions (manual photography). follows:
350 TV lines or better at the center
and 300 TV lines or better at the
periphery (NTSC).
300 TV lines or better at the center
and 250 TV lines or better at the
periphery (PAL).
(3) Check images shot at Rotate image (3) Direction of rotate image have to
(manual photography). correct.
(4) Disconnect the HDMI CABLE from
the camera.
13 PC connection - (1)Connect the camera to the PC with (1) Check that the PC recognizes the ZJ00982-100
checking the USB/AV CABLE. camera over a PTP connection.
(2) Copy the image files in the camera (2) Check that the image files have
to a folder on the PC. been copied to the PC.
(3) Disconnect the USB/AV CABLE from
the camera.

4-3
 Confidential: FUJIFILM Service Center Use Only

X-Pro1 Service Manual

14 Erase mode check Erase (1) Select “Erase” -> (1) Check that an erase message such
“ALL FRAMES” from the menu as the following appears:
and then press the “OK” button. Overseas: “ERASE ALL OK?”
China: “ OK?”
(2) Select "OK" and press the “OK” (2) Check that the recorded images are
button. erased.
(3) Turn the camera off.
(4) Disconnect the SD card from the
camera.
15 Playback mode Playback (1) Insert a LCD INSPECTION SD card. ZJ00855-100
check (2) Turn the camera on. ZPU0512-100
(3) If a message prompting the user to (3) <DISP/BACK>
set the date appears, press the butt
on specified on the right.
(4) Start up in playback mode.
(5) Check the playback image. (5) Check that the last image shot
appears, regardless of whether it
is automatic or manual. Check that
the date is displayed in the YYYY.
[Link] format.
16 LCD dust/defect Playback (1) Play back a completely black image. (1) Check that there are no noticeable ZJ00885-100
check dust flecks or stains (bright spots,
smears, flashing points, etc.) on the
screen.
(2) Play back a completely white (75%)
image.
17 EVF dust/defect Playback (1) Change to EVF display. (1) Push the VIEW MODE button. ZJ00885-100
check (2) Play back a completely white (75%) (2) Check that there are no noticeable
image. dust flecks or stains (bright spots,
smears, flashing points, etc.) on the
screen.
(3) Play back a completely black image.
18 Eye sensor check Playback (1) Set the Eye Sensor mode. (1) Push the VIEW MODE button and turn
(2) Bring eyes close to EVF in a state on the Eye Sensor.
displayed by LCD. (2) Displayed by EVF.
(3) Keep away eyes from EVF. (3) Displayed by LCD.
(4) Turn the camera off.
19 Battery low check P mode (1) Set the power supply voltage. (1) 7.80 V ± 0.10 V ZJ01936-100
(2) Select the mode dial setting. (2) Mode: IRIS AUTO/SS AUTO.
(3) Turn the camera on.
(4) Set the power supply voltage. (4) 6.40 V ± 0.04V
Check that the battery-low warning
(pre-end) appears.
(5) Turn the camera off. (5) Check the camera turns off.
(6) Remove battery and am connected
again once after progress more than
ten seconds.
20 Current P mode (1) Set the power supply voltage. (1) 7.80 V ± 0.10 V ZJ01936-100
consumption check (2) Select the mode dial setting. (2) Mode: IRIS AUTO/SS AUTO.
AF Mode: AF-S.
(3) Turn the camera on.
(4) Check the Macro mode. (4) Backup check.
(5) Macro mode is set as off.
(6) After the LCD live image appears, (6) 500 mA or less
check the current consumption.

4-4
 Confidential: FUJIFILM Service Center Use Only

X-Pro1 Service Manual

21 Variable power P mode (1) Look into the OVF and check the (1) In an EVF display, EVF lever is plulled.
lens check OVF display.
(2) EVF lever is pulled a long time and
check the variable power lens comes
out.
(3) Again EVF lever is pulled a long time
and the variable power lens
is returned.
(4) Turn the camera off.
22 Checking standby Power off (1) Chek the power supply voltage. (1) 7.80 V ± 0.10 V ZJ01936-100
current (2) Check the standby current when the (2) 0.5 mA or less
power is turned OFF.
(3) Disconnect the SD card from the
camera.
23 Removal of a (1) 35mm Lens is removed. (1) Garbage dose not enter to the inside
lens of
a lens mount.
There is no crease,bend,dent in a
(2) Lens mount cover is attached. mount pin.
24 Shipping (1) Mode dial. (1) Aperture value AUTO/Shutter Speed
inspection AUTO/ Exposure 0EV
(Inventory repairs (2) AF changeover switch. (2) AF-S
only) (3) SETUP frame no. (3) New: The default SETUP frame No.
setting is “Continuous”, but to clear
the number of frames in the frame
number memory to zero, you should
always change the setting to “New”
before turning the camera off.
(4) Variable power lens. (4) OFF
(5) Battery and cards not inserted. (5) Normal
(6) Battery cover. (6) Closed
(7) DC coupler cable cover. (7) Closed
(8) Terminal cover. (8) Closed
(9) Lens mount cover. (9) Set
(10) Synchronization terminal cover. (10) Set
(11) Power off. (11) The power supply is stopped after
the camera's shutdown sequence
ends.
* Setting and clearing date
(1) Connect the USB/AV CABLE from
the PC to the camera (ensure that
the PC is switched ON).
(2) Switch power ON (POWER_ON)
while pressing the shutter button and
button.
(3) Switch power OFF (POWER_OFF).
(4) Check that the date has been
cleared.
* Please downloaded from Web server ([Link] or [Link]

4-5
 Confidential: FUJIFILM Service Center Use Only

X-Pro1 Service Manual

4-4. Resolution Check

<Settings for Resolution Check >
(1) It cuts it like figure 2, and please stick FxX100 Line
Illumination of the resolution chart
Chart (ZJ01848-100) on a board of 1,204.1mm X
Center :500～850LX
796.9mm. Source of light. Periphery : 0 ～ +400LX (For the
(2) Referring to right figure 1, Prepare for a camera and
resolution chart.
(3) Lights up the resolution chart with a source of light.
(4) Brightness of the resolution chart
Center :500～850LX
Periphery: 0～+400LX (For the center)

Resolution Chart
ZJ01848-100
From the surface of the
mount

Figure.1
<STEP 1>
[Resolution Check initialization]
(1) 35mm Lens is attached.
(2) Set the Battery and SD card to the camera.
(3) Turn the camera on.
(4) Carry out the reset of Camera from MENU
(5) Set a camera as follows
1. Shooting mode : A (Aperture Value)
[Link] : 200
[Link] : Fluorescent light -3
[Link] value : F4
[Link] simulation : Standard
[Link]-timer : 2sec
(6) Fix a camera to a tripod, and point a camera to the
resolution chart.
(7) Set resolution chart at the position of 1200mm (+-3mm)
from the lens tip of the camera.
(8) Match a chart angle of view with LCD like figure 2.
(9) Photograph it. Figure.2
* If a self-timer begins to work, please do not touch the
camera.

4-6
 Confidential: FUJIFILM Service Center Use Only

X-Pro1 Service Manual

＜STEP 2＞
[Resolution Check]
(1) Check the resolution at the center and periphery of the
photography image with the monitor of the PC. Periphery
Periphery Center
[SPEC] * Check an image at actual size
Center : What the line of the part to say 20 can
distinguish.
Periphery: What the line of the part to say 15 can Periphery
Periphery
distinguish.

Periphery check positions

Center check positions

A judgment example
*Periphery

NG OK
＜STEP 3＞
[Ending Resolution Check]
If an OK, carry out the following..
(1) Carry out the reset of Camera from MENU.
(2) Turn the camera off.
(3) Disconnect from the tripod.
(4) Take out battery and SD card.
(5) Close the cover of Battery and Treminal.
(6) 35mm Lens is removed.

4-7
 Confidential: FUJIFILM Service Center Use Only

X-Pro1 Service Manual

4-5. Finder dust check

< Finder appearance >
Finder appearance inspection
(1) Wipe the dust dirt of the lens surface, finder window.
(2) Comparative size is measured appearance inspection
sample chart and dust.

<Finder appearance inspection standard>

・ OK to the size of φ0.15mm
・ Size of φ0.10 to 0.15mm be OK to 1 piece
Finder appearance inspection
Comparison

< Finder appearance(lens at zoom ratio) >

(1) Change FINDER .
Wipe the dust dirt of the lens surface, finder window. Finder appearance inspection
(2) Comparative size is measured appearance inspection
sample chart and dust.

<Finder appearance inspection standard>

・ OK to the size of φ0.15mm
・ Size of φ0.10 to 0.15mm be OK to 1 piece

<Dust of finder (when seeing apart)>

＊insert a different lens at zoom ratio. Inspection method
(1) Appearance inspection sample chart is projected on the
finder window. white photographic subject.
(2) Finder is turned to a white photographic subject.
Distance the 20cm see the finder inside.
(3) Comparative size is measured appearance inspection
sample chart and dust.

< Inspection standard > 20 ㎝

・ OK to the size of φ0.13mm
・ Size of φ0.10 to 0.13mm be OK to 2 piece

UNIT MOUNT

<Dust of finder >

＊insert a different lens at zoom ratio. Inspection method
(1) Appearance inspection sample chart is projected on the
finder window.
(2) Finder is turned to a white photographic subject. white photographic subject.
See the finder inside.
(3) Comparative size is measured dot chart and dust.

< Inspection standard >

・ OK to the size of φ0.15mm

UNIT MOUNT

Revised:[Link].2012

4-8
 Confidential: FUJIFILM Service Center Use Only

X-Pro1 Service Manual

4-6. CMOS Cleaning and Inspection Procedures

CMOS is incorporated with this model as an image sensor. Dust etc. could stick to the CMOS and depending on shooting conditions
and the type of subject, it could be recorded in images.
If it is the case, the CMOS needs to be cleaned.

4-6-1. Visual Inspection for Dusts and Cleaning method

<Step 1>
Check if the camera is switched off and remove the battery.

<Step 2>
Remove the interchangeable lens from the camera.

<Step 3>
Hold the camera so that light goes to the CMOS and check if there are dusts on the CMOS surface either visually or by using a
microscope.
If dusts can be seen, use a blower to remove it ([Note]).
If the dusts cannot be removed using the blower, wipe the CMOS with a lens cleaner (OLYMPUS HYPER CLEAN EE-3310 or
Equivalent goods) and ZS00172-100 CLEANING PAPER or Equivalent goods.
Do not use a blower with a brush.
Using a blower-brush to clean the CMOS could scratch the CMOS surface.

[Note]
When swiping the CMOS, note that any metallic dusts on the CMOS surface will cause scratches in the CMOS surface during cleaning.

4-6-2. Installation of X-Pro1 W Dust Inspection Soft Ver.*.**

<Step 1>
Download the inspection software from WEB and install the
software in a PC.
X-Pro1 W Dust Inspection Soft Ver.*.** ZJ02093-***.zip
We have uploaded the “X-Pro1 W Dust Inspection Soft Ver.*.**
(ZJ02093-***.zip)” on our website:
([Link]

<Step 2>
“ZJ02093-***” is a compressed file of “ZIP”.
The “ZJ02093-***” folder can be decompressed by “Compression
software”.
Copy the “ZJ02093-***” folder to the “C” drive in the PC.

<Step 3>
Double-click the inspection software installer file of “Setup_X-
Pro1_W_DustInspection_***.exe” in the “ZJ02093-***” folder.

<Step 4>
When the window in the right appears, click [Next].

: Revised

4-9
 Confidential: FUJIFILM Service Center Use Only

X-Pro1 Service Manual

<Step 5>
When the window in the right appears, click [Install].
(Then, installation begins.)

<Step 6>
When the installation completes and the window in the right
appears, click [Finish].

: Revised
4-10
 Confidential: FUJIFILM Service Center Use Only

X-Pro1 Service Manual

4-6-3. Uninstalling X-Pro1 W Dust Inspection Soft Ver.*.**

<Step 1>
Click: Start
↓
Programs
↓
FUJIFILM REPAIR SERVICE
↓
X-Pro1 W Dust Inspection Soft
↓
Uninstall X-Pro1 W Dust Inspection Soft

<Step 2>
When the window in the right appears, click [Yes].
(Then, uninstallation begins.)

<Step 3>
When the uninstallation completes and the window in the right
appears, click [OK].

* In some cases, uninstalling the software does not remove all the files.
To completely remove all the files, delete the C:\X-Pro1_W_DustInspection folder after completing the uninstallation.

: Revised
4-11
 Confidential: FUJIFILM Service Center Use Only

X-Pro1 Service Manual

4-6-4. Inspection of Dusts by the Shooting Test

<Step 1>
Mount XF35mmF1.4R lens on the camera.

<Step 2>
Click: Start
↓
Programs
↓
FUJIFILM REPAIR SERVICE
↓
X-Pro1 W Dust Inspection Soft
↓
X-Pro1_W(DustInspection)

<Step 3>
If this procedure stops at the window in the right, press the [Enter]
key to proceed.

<Step 4>
1. Connect the camera to the PC using the “USB cable”.
2. Supply power to the camera.
3. Turn the camera on while holding down the shutter button
and selector up key ().
4. Confirm if the LED is on in green.

After completing steps 1 to 4, press the [Enter] key to proceed.

: Revised
4-12
 Confidential: FUJIFILM Service Center Use Only

X-Pro1 Service Manual

<Step 5>
(1) Place the VIEWER at a distance of 24mm or less from the
lens-face of the camera.
(2) Adjust the position of the camera so that the camera LCD
shows the center of the VIEWER is displayed.

After completing steps 1 to 2, press the [Enter] key to proceed.

<Step 6>
[OK]
If the inspection is OK, the window in the right will appear.

: Revised
4-13
 Confidential: FUJIFILM Service Center Use Only

X-Pro1 Service Manual

[NG]
If the inspection is NG, the window in the right will appear showing
the location of dusts.

(1) Check the location of dusts and close the window.

(2) Remove dusts and inspect again.
* The captured image is saved in
C:\X-Pro1_W_DustInspection\SCRIPT\LX10\GOMI\JPG.

<Step 7>
(1) Turn the camera off.
(2) Disconnect the USB cable from the camera.

[Note]
In a normal environment, dusts could stick to the CMOS surface.
Therefore, customers could complain about dusts on the CMOS and ask you to remove them again just after you have removed the
dusts and they use their cameras.
In order to prepare such cases, we recommend you to take pictures before and after you clean the CMOS. Depending on cases, we
think you need to show those pictures to customers.

: Revised
4-14
 Confidential: FUJIFILM Service Center Use Only

X-Pro1 Service Manual

5 Parts List 1(Packing and Accessories)

5-1. US-Model
•Black model
Ref No. Parts No. Description Comment
A101 FBB23163-100 MANUAL BAG
A102 FBB23194-100 BARCODE LABEL
A103 FBB23777-100 US WARRANTY CD-SIZE1
A104 FBB23779-100 US STOP CD-SIZE1
A105 FBB23781-100 WWN_PRINT CD-SIZE2

A106 FBB24290-100 LABEL PRODUCT W

A107 FBB24527-100 [Link] Y-10241
A108 FBB24531-100 TRAY Y-10241
A109 FBB24634-100 ACC BOX Y-10241
A110 FBB24774-100 HDPE BAG 190×200

A111 FBF08577-100 UNIT BELT RING

A112 FBL01619-200 LX10 OM EN
A113 FBL01619-500 LX10 OM ES
A114 FBU04414-100 CAMERA BOX ASSY
A115 FFZ06894-101 AC POWERCORD

A116 FFZ08017-100 USB CABLE L60

A117 FFZ09206-200 BATTERYPACK NP-W126U
A118 FFZ09207-100 BATTERY CHARGER JU
A119 FFZ09208-101 LX10 CD-ROM
A120 FFZ09365-100 SHOULDER BELT Y10241

 A121 FBL01762-100 LX10_FWUP_INS

 Revised: Aug. 10, 2012

5-1
 Confidential: FUJIFILM Service Center Use Only

X-Pro1 Service Manual

5-2. AS-Model
•Black model
Ref No. Parts No. Description Comment
A101 FBB23163-100 MANUAL BAG
A102 FBB23194-100 BARCODE LABEL
A103 FBB23334-100 PRG ACC CDSIZE 01
A104 FBB23781-100 WWN PRINT CD-SIZE2
A105 FBB24290-200 LABEL PRODUCT E

A106 FBB24527-100 [Link] Y-10241

A107 FBB24531-100 TRAY Y-10241
A108 FBB24634-100 ACC BOX Y-10241
A109 FBB24774-100 HDPE BAG 190×200
A110 FBF08577-100 UNIT BELT RING
A111 FBL01619-200 LX10 OM EN
A112 FBU04414-100 CAMERA BOX ASSY
A113 FFZ08017-100 USB CABLE L60
A114 FFZ09206-300 BATTERYPACK NP-W126W
A115 FFZ09207-200 BATTERY CHARGER WW
A116 FFZ09208-101 LX10 CD-ROM
A117 FFZ09365-100 SHOULDER BELT Y10241
 A118 FBL01762-100 LX10 FWUP INS

 Revised: Aug. 10, 2012

5-2
 Confidential: FUJIFILM Service Center Use Only

X-Pro1 Service Manual

5-3. E1-Model
•Black model
Ref No. Parts No. Description Comment
A101 FBB23163-100 MANUAL BAG
A102 FBB23193-100 BARCODE LABEL
A103 FBB23334-100 PRG ACC CDSIZE 01
A104 FBB23781-100 WWN PRINT CD-SIZE2
A105 FBB24290-200 LABEL PRODUCT E

A106 FBB24527-100 [Link] Y-10241

A107 FBB24531-100 TRAY Y-10241
A108 FBB24634-100 ACC BOX Y-10241
A109 FBB24774-100 HDPE BAG 190×200
A110 FBF08577-100 UNIT BELT RING
A111 FBL01619-300 LX10 OM FR
A112 FBL01619-400 LX10 OM DE
A113 FBU04414-100 CAMERA BOX ASSY
A114 FFZ06708-301 AC POWERCORD
A115 FFZ08017-100 USB CABLE L60
A116 FFZ09206-300 BATTERYPACK NP-W126W
A117 FFZ09207-200 BATTERY CHARGER
A118 FFZ09208-101 LX10 CD-ROM
A119 FFZ09365-100 SHOULDER BELT Y10241
 A120 FBL01762-100 LX10 FWUP INS

 Revised: Aug. 10, 2012

5-3
 Confidential: FUJIFILM Service Center Use Only

X-Pro1 Service Manual

5-4. EE-Model
•Black model
Ref No. Parts No. Description Comment
A101 FBB23163-100 MANUAL BAG
A102 FBB23193-100 BARCODE LABEL
A103 FBB23334-100 PRG ACC CDSIZE 01
A104 FBB23781-100 WWN PRINT CD-SIZE2
A105 FBB24290-200 LABEL PRODUCT E

A106 FBB24527-100 [Link] Y-10241

A107 FBB24531-100 TRAY Y-10241
A108 FBB24634-100 ACC BOX Y-10241
A109 FBB24774-100 HDPE BAG 190×200
A110 FBF08577-100 UNIT BELT RING

A111 FBL01619-200 LX10 OM EN

A112 FBU04414-100 CAMERA BOX ASSY
A113 FFZ06708-301 AC POWERCORD
A114 FFZ08017-100 USB CABLE L60
A115 FFZ09206-300 BATTERYPACK NP-W126W

A116 FFZ09207-200 BATTERY CHARGER WW

A117 FFZ09208-101 LX10 CD-ROM
A118 FFZ09365-100 SHOULDER BELT Y10241
 A119 FBL01762-100 LX10 FWUP INS

 Revised: Aug. 10, 2012

5-4
 Confidential: FUJIFILM Service Center Use Only

X-Pro1 Service Manual

5-5. EG-Model
•Black model
Ref No. Parts No. Description Comment
A101 FBB23163-100 MANUAL BAG
A102 FBB23193-100 BARCODE LABEL
A103 FBB23334-100 PRG ACC CDSIZE 01
A104 FBB23781-100 WWN PRINT CD-SIZE2
A105 FBB24290-200 LABEL PRODUCT E
A106 FBB24527-100 [Link] Y-10241
A107 FBB24531-100 TRAY Y-10241
A108 FBB24634-100 ACC BOX Y-10241
A109 FBB24774-100 HDPE BAG 190×200
A110 FBF08577-100 UNIT BELT RING
A111 FBL01619-200 LX10 OM EN
A112 FBU04414-100 CAMERA BOX ASSY
A113 FFZ06708-401 AC POWERCORD
A114 FFZ08017-100 USB CABLE L60
A115 FFZ09206-300 BATTERYPACK NP-W126W

A116 FFZ09207-200 BATTERY CHARGER WW

A117 FFZ09208-101 LX10 CD-ROM
A118 FFZ09365-100 SHOULDER BELT Y10241
 A119 FBL01762-100 LX10 FWUP INS

 Revised: Aug. 10, 2012

5-5
 Confidential: FUJIFILM Service Center Use Only

X-Pro1 Service Manual

5-6. EU-Model
•Black model
Ref No. Parts No. Description Comment
A101 FBB23163-100 MANUAL BAG
A102 FBB23193-100 BARCODE LABEL
A103 FBB23334-100 PRG ACC CDSIZE 01
A104 FBB23781-100 WWN PRINT CD-SIZE2
A105 FBB24290-200 LABEL PRODUCT E

A106 FBB24527-100 [Link] Y-10241

A107 FBB24531-100 TRAY Y-10241
A108 FBB24634-100 ACC BOX Y-10241
A109 FBB24774-100 HDPE BAG 190×200
A110 FBF08577-100 UNIT BELT RING

A111 FBU04414-100 CAMERA BOX ASSY

A112 FFZ06708-301 AC POWERCORD
A113 FFZ08017-100 USB CABLE L60
A114 FFZ09206-300 BATTERYPACK NP-W126W
A115 FFZ09207-200 BATTERY CHARGER

A116 FFZ09208-101 LX10 CD-ROM

A117 FFZ09365-100 SHOULDER BELT Y10241
 A118 FBL01762-100 LX10 FWUP INS

 Revised: Aug. 10, 2012

5-6
 Confidential: FUJIFILM Service Center Use Only

X-Pro1 Service Manual

5-7. RU-Model
•Black model
Ref No. Parts No. Description Comment
A101 FBB21384-101 RU STICKER
A102 FBB23163-100 MANUAL BAG
A103 FBB23193-100 BARCODE LABEL
A104 FBB23334-100 PRG_ACC_CDSIZE_01
A105 FBB23781-100 WWN_PRINT CD-SIZE2

A106 FBB24290-200 LABEL PRODUCT E

A107 FBB24527-100 [Link] Y-10241
A108 FBB24531-100 TRAY Y-10241
A109 FBB24634-100 ACC BOX Y-10241
A110 FBB24774-100 HDPE BAG 190×200

A111 FBB24776-100 Russia-Warranty

A112 FBF08577-100 UNIT BELT RING
A113 FBL01619-K00 LX10 OM RU
A114 FBU04414-100 CAMERA BOX ASSY
A115 FFZ06708-301 AC POWERCORD

A116 FFZ08017-100 USB CABLE L60

A117 FFZ09206-300 BATTERYPACK NP-W126W
A118 FFZ09207-200 BATTERY CHARGER
A119 FFZ09208-101 LX10 CD-ROM
A120 FFZ09365-100 SHOULDER BELT Y10241

 A121 FBL01762-100 LX10_FWUP_INS

 Revised: Aug. 10, 2012

5-7
 Confidential: FUJIFILM Service Center Use Only

X-Pro1 Service Manual

5-8. CH-Model
•Black model
Ref No. Parts No. Description Comment
A101 FBB19104-105 正規品証明シール
A102 FBB23163-100 MANUAL BAG
A103 FBB23193-100 BARCODE LABEL
A104 FBB23780-101 CH SERVICE NETWORK 1
A105 FBB24290-100 LABEL PRODUCT W

A106 FBB24527-200 [Link] Y-10249

A107 FBB24531-100 TRAY Y-10241
A108 FBB24634-100 ACC BOX Y-10241
A109 FBB24774-100 HDPE BAG 190×200
A110 FBF08577-100 UNIT BELT RING

A111 FBL01619-600 LX10 OM ZHS

A112 FBU04414-100 CAMERA BOX ASSY
A113 FFZ05432-401 POWER SUPPLY CORD
A114 FFZ08017-100 USB CABLE L60
A115 FFZ09206-300 BATTERYPACK NP-W126W

A116 FFZ09207-200 BATTERY CHARGER

A117 FFZ09208-101 LX10 CD-ROM
A118 FFZ09365-100 SHOULDER BELT Y10241
A119 FBB23686-100 [Link] VOID SEAL
A120 FBB23778-100 WARRANTY CN CD-SIZE

 A121 FBL01762-100 LX10_FWUP_INS

 Revised: Aug. 10, 2012

5-8
 Confidential: FUJIFILM Service Center Use Only

X-Pro1 Service Manual

5-9. JP-Model
•Black model
Ref No. Parts No. Description Comment
A101 FBB21304-100 WARRANTY JP
A102 FBB23163-100 MANUAL BAG
A103 FBB23193-100 BARCODE LABEL
A104 FBB24290-100 LABEL PRODUCT W
A105 FBB24527-100 [Link] Y-10241

A106 FBB24531-100 TRAY Y-10241

A107 FBB24634-100 ACC BOX Y-10241
A108 FBB24773-100 My FUJIFILM paper
A109 FBB24774-100 HDPE BAG 190×200
A110 FBF08577-100 UNIT BELT RING

A111 FBL01619-100 LX10 OM JP

A112 FBU04414-100 CAMERA BOX ASSY
A113 FFZ06708-100 AC POWERCORD
A114 FFZ08017-100 USB CABLE L60
A115 FFZ09206-100 BATTERYPACK NP-W126J

A116 FFZ09207-100 BATTERY CHARGER

A117 FFZ09208-101 LX10 CD-ROM
A118 FFZ09365-100 SHOULDER BELT Y10241
 A119 FBL01762-100 LX10_FWUP_INS

 Revised: Aug. 10, 2012

5-9
 Confidential: FUJIFILM Service Center Use Only

X-Pro1 Service Manual

MEMO

5-10
 Confidential: FUJIFILM Service Center Use Only

X-Pro1 Service Manual

6. Parts List 2(Mechanical Block)

6-1. US/AS/E1/EE/EG/EU/RU/CH/JP-Model
（X-Pro1）
・Black model
M201
Ref No. Parts No. Description Commen
M209
M201 FBB17681-300 BT2M1.7X3.5
M209 M202 FBB17681-600 BT2M1.7X5.0
M203 FBB20523-100 MSAM1.4X2.5N
M230 M204 FBB20592-100 N-MS2M1.7X3.0
M213 M205 FBB20921-100 N-MSGM1.7X2.5

M202 M206 FBB20921-400 N-MSGM1.7X4.0

N.S. FBB21217-300 MS2M1.7X3.5
M228 M208 FBB21217-400 MS2M1.7X4.0
M231 M209 FBB22744-100 MSGM1.7X2.5
M210 FBB24071-100 N-MSGM1.7X2.5D
UL
UL TAPE
M201 M211 FBB24119-100 COVER BATTERY
M212 FBB24146-100 HOLDER SYNCHRO
M218
M224
M224 M213 FBB24148-100 TRIPOD SCREW
M229 M214 FBB24156-100 COVER SYNCHRO
M209 M215 FBB24157-100 PLATE SYNCHRO
UL
UL TAPE M201 M216 FBB24166-300 CAP BODY
M217 FBB24260-100 HARNESS SY BK
M218 FBB24269-100 CUSHION CN LCD
M232 M219 FBB24270-100 SHEET COVER FPS
M220 FBB24285-100 WINDOW LCD

M220 M221 FBB24286-100 CUSHION　LCD

M234 M222 FBB24287-100 SHEET FRONT
M203
M223 FBB24303-100 SHEET INSULATE SINK
M227 M224 FBB24717-100 SHEET CU SINK
M223 M225 FBB24718-100 SHEET COND SINK
M221
M211 M226 FBF09457-100 CONST ASSY FRONT
M227 FBF09461-100 CONST BATT
M225
M206 M237
M237 M228 FBF09462-100 CONST FPC COMMAND
M224 M229 FBF09463-100 CONST FRAME MAIN
M230 FBF09464-100 CONST PWB SIDE

M236 M217 M235 M231 FBF09465-100 CONST TOP

M232 FBF09466-100 CONST REAR
M215 M233 FBF09480-100 UNIT MOUNT
M208 M234 FCB2301-A100 Y-10241MAINPWB ASSY
M235 FFZ06350-101 SYNCHRO TERMINAL

M214 M236 FFZ09111-100 SPEAKER

M205 M233  M237 FFZ09198-100 LCD

M216 M219
M206
M204
M205 M209
M226 M212
M210

M222

: Revised
 Revised: [Link].2012
6-1
 Confidential: FUJIFILM Service Center Use Only

X-Pro1 Service Manual

・ B la c k m o d e l
Re f No. P a rts N o . D e s c rip tio n Com m e nt
M 301 F B B 2 0 5 9 2 -1 0 0 N -M S 2 M 1 .7 X 3 .0
M 302 F B B 2 0 9 2 1 -1 0 0 N -M S G M 1 .7 X 2 .5
M 303 F B B 2 0 9 2 1 -4 0 0 N -M S G M 1 .7 X 4 .0
M 304 F B B 2 1 2 1 7 -3 0 0 M S 2 M 1 .7 X 3 .5
M 305 F B B 2 2 5 5 0 -A 0 0 M S 2 M 1 .4 X 2 .0

M 306 F B B 2 4 0 7 1 -1 0 0 N -M S G M 1 .7 X 2 .5 D
M 307 F B B 2 4 1 1 0 -1 0 0 L E V E R F IN D E R
M 308 F B B 2 4 1 4 2 -1 0 0 B A S E G R IP F
M 309 F B B 2 4 1 4 4 -1 0 0 G R IP F
M312 M 310 F B B 2 4 2 4 9 -1 0 0 S H E E T G R IP F R IG H T

M 311 F B B 2 4 2 5 0 -1 0 0 S H E E T G R IP F L E F T
M 312 F B B 2 4 2 5 1 -1 0 0 S H E E T G R IP R R IG H T
M302 M 313 F B B 2 4 2 5 2 -1 0 0 S H E E T G R IP R L E F T
M 314 F B B 2 4 2 8 8 -1 0 0 DE CO P L A T E L E V E R
M316 M 315 F B B 2 4 2 8 9 -1 0 0 T A P E G R IP F

M303 M 316 F F Z 0 9 2 1 0 -1 0 0 U N IT R IN G F IN D E R

M301

M310

M313
M303
M301
M304

M307
M305
M314

M308
M306
M315
M311
M309

6-2
 Confidential: FUJIFILM Service Center Use Only

X-Pro1 Service Manual

 Ref No . Part s N o. D escrip ti on Co m me n

M 401 FBF 095 88-1 00 H OLDER MOUN T ASSY
M 402 FF Z 09378- 100 Y- 1024 1 MO U NT FPC
M 403 FBB2 4173- 100 M ASK MO U NT
M402 M401 M408 M 404
M 405
FF Z 09105- 100
FBF 095 91-1 00
F P SHU TT ER
D R GLASS UNIT

M 406 FBB2 4452- 100 T APE F PC

M 407 FBB2 4178- 100 SH EET CU
 M 408 FBB2 4168- 200 PSP MOUN T

M407

M403
M404

M406 M405

: Revised
: Revised
6-3
 Confidential: FUJIFILM Service Center Use Only

X-Pro1 Service Manual

MEMO

6-4
 Confidential: FUJIFILM Service Center Use Only

X-Pro1 Service Manual

7. Electrical parts

[Note]
* Due to standardization, replacement in the parts list may
The components indicated by mark are critical for safety. be different from the parts list specified in the circuit or the
When indicated parts by reference number, please include components used on the set.
*Do not reuse removed parts. Always use new parts.
the board name.

PWB
Ref No. Parts No. Description Comment
diagram
MAIN PWB ASSY
[FUSE]
F501 FFP00039-403 FUSE
[BATTERY]
BT151 FFZ07531-100 BACKUP BATTERY
SHOE FPC ASSY
[LED]
- FFQDL0155-01 LED

7-1
 Confidential: FUJIFILM Service Center Use Only

X-Pro1 Service Manual

MEMO

7-2
 Confidential: FUJIFILM Service Center Use Only

X-Pro1 Service Manual

8. Appendix
8-1. List of Related Technical Updates Issued
To ensure that after-sales service is performed accurately, keep a record here of the technical updates issued that cover this
device.
Technical Update No. Date Title Details/Other

2012-029 21. Jan, 2012 Service manual revision Revised pages: P1-23 to P1-36

Revised pages: P1-21 to P1-22, P1-36, P3-4, P3-12,

P3-14, P3-16, P3-18, P3-20,
2012-058 13. Apr, 2012 Service manual revision
P3-24, P3-26, P3-28, P3-31,
P3-36, P6-1

Revised pages: P4-1, P4-8

2012-074 20. Apr, 2012 Service manual revision
Addition pages: P1-37 to P1-38

2012-123 27. Jun, 2012 Service manual revision Revised pages: P3-19, P3-34 and P3-35

2012-143 10. Aug, 2012 Service manual revision Revised pages: P5-1 to P5-9

Addition of the Inspection

2012-181 03 Sep 2012 software and revision of  Revised pages: P4-1 and P4-9 to P4-14
service manual

2012-246 21 Dec 2012 Revision of Service Manual  Revised page: P6-1

2013-108 01 Jul 2013 Revision of Service Manual  Revised page: P1-18 to P1-27, P1-33 to P1-34
and P6-3

2013-212 17 Oct 2013 Revision of Service Manual  Revised page: P3-2 and P6-3

8-1
 Confidential: FUJIFILM Service Center Use Only

X-Pro1 Service Manual

8-2