Scribd
Upload
311 views4 pages

Job Sheet 1.1-1: CBLM Rac Servicing (Domrac NC Ii) Installing and Configuring Computer Systems

The document provides instructions for installing a computer power supply. It lists safety precautions and 12 steps to install the power supply unit into the computer case. These include checking compatibility of the power supply and case, properly grounding yourself, opening the case, setting the power supply voltage switch, inserting the power supply unit into the computer case and screwing it into place, attaching power connections to the motherboard and components, closing the case, and turning the computer on. It concludes with a performance criteria checklist to ensure all installation steps were completed correctly.

Uploaded by

JOSEPH RIŇOS
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as DOCX, PDF, TXT or read online on Scribd
311 views4 pages

Job Sheet 1.1-1: CBLM Rac Servicing (Domrac NC Ii) Installing and Configuring Computer Systems

The document provides instructions for installing a computer power supply. It lists safety precautions and 12 steps to install the power supply unit into the computer case. These include checking compatibility of the power supply and case, properly grounding yourself, opening the case, setting the power supply voltage switch, inserting the power supply unit into the computer case and screwing it into place, attaching power connections to the motherboard and components, closing the case, and turning the computer on. It concludes with a performance criteria checklist to ensure all installation steps were completed correctly.

Uploaded by

JOSEPH RIŇOS
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as DOCX, PDF, TXT or read online on Scribd

CBLM RAC SERVICING(DOMRAC NC II)

Installing and Configuring Computer Systems

Job Sheet 1.1-1

Unit of Competency: Maintain and Se

Title: Install Computer Hardware: Power Supply


Performance Objective:
Given the necessary materials and equipment, the trainee will be
able to check the system unit and the power supply for thirty (30) minutes
only to perform the task.

Supplies/Materials: Examination Test Paper and Screw drivers


Equipment: System Unit/Computer Case and Power Supply Unit

Step/Procedure:

Safety Precaution Reminders:

● Wear your proper PPE


● Remove your jewelries and secure loose clothing
● Locate where the fire extinguisher and how to use it
● Avoid foods and drinks out of the workplace.

1. Find a power supply for the system unit.


1.1 Check if the screw slots of the power supply unit are compatible
to the slots of the computer case.
2. Assemble your tools (screw drivers)
3. Ground yourself
3.1 Check if you are wearing rubber sole shoes
3.2 Wear Anti-Static wrist strap
4. Open the computer case.
5. Lay the case on its side, with exposed Hi side facing up.
6. Set the power supply’s voltage switch. (if the power supply have any)
7. Find the power supply’s intended location.
7.1 Insert the Power Supply Unit to the Computer Case.
7.2 Check the screw locations if parallel to both units
7.3 Screw the power supply into place.
8. Attach the power supply to the motherboard and other components.
(Hard Disk Drive, Floppy Disk Drive, CD drive and Graphics card)
8.1 Slowly push both end of the ATX-2 Molex Power Connector to
the ATX Power Port following the port guide
8.2 Plug the ATX 4 Pin Molex 12V P4 Connector to the ATX 12V
port following the guide of the port

TESDA Regional Training Center Kenneth Paul A. Banzali – TM1 Revision 00


CBLM RAC SERVICING(DOMRAC NC II)
Installing and Configuring Computer Systems

8.3 Plug SATA Power cable following the guide of the port
8.4 Plug 4 Pin Molex Peripheral connector to the external fan.
9. Close and plug back into the PC.
11.1 Place the cover back on the PC
11.2 Stand the computer case up
11.3 Plug the power cord and other back panel peripherals

12. Turn on the computer.

Assessment Method:
1. Written Examination
2. Demonstration
3. Oral Questioning

TESDA Regional Training Center Kenneth Paul A. Banzali – TM1 Revision 00


CBLM RAC SERVICING(DOMRAC NC II)
Installing and Configuring Computer Systems

Performance Criteria Checklist 1.1-1

Criteria YES NO
Did you?..
Find a power supply for the system unit?

Assemble your tools?


Ground yourself?

Open the computer case?

Lay the case on its side, with exposed side facing up?

Set the power supply’s voltage switch?

Find the power supply’s intended location?

Insert the power supply?

Attach the power supply to the motherboard and other


components?

Close and plug back into the PC?

Turn on the computer?

Comments/Suggestions:

TESDA Regional Training Center Kenneth Paul A. Banzali – TM1 Revision 00


CBLM RAC SERVICING(DOMRAC NC II)
Installing and Configuring Computer Systems

TESDA Regional Training Center Kenneth Paul A. Banzali – TM1 Revision 00

You might also like