Motor Cleaning Methods and Selection Factors June 10, 2020
Motor Cleaning Methods and Selection Factors
Tom Bishop, P.E.- Senior Technical Support Specialist
Electrical Apparatus Service Association, Inc.
+1 314 993 2220 | tbishop@[Link]
How to ask questions
Joined using web browser Joined using web browser
+ Zoom plugin
When prompted, reconfirm
Wait to Submit the audio source you’re using
be called written
on question
Ask
question Ask question verbally
verbally
EASA @ 2020 1
Motor Cleaning Methods and Selection Factors June 10, 2020
Introduction
• Focus on best methods
• Features
• Benefits
• Drawbacks
• Determine which options are best for you
Methods and Selection Factors
• Methods
– Solvent
– Aqueous (water-based)
– Other more aggressive methods
• Selection Factors
– Size and quantity of parts to be cleaned
– Type of part, e.g. stators, rotors, housings
– Type of cleaning agent
• Solvent
• Aqueous
– Environmental and safety concerns
EASA @ 2020 2
Motor Cleaning Methods and Selection Factors June 10, 2020
Methods Addressed
• Solvent cleaning • Enzyme systems
• Steam cleaning • Pyrolysis cleaning
• Pressure washer • Dry ice cleaning
• Parts washing • Grit blasting
machines • Water blasting
• Ultrasonic systems
Also addressed
• Selection of aqueous cleaning agents
• Disposal of aqueous cleaning byproducts
Solvent Cleaning
• Primarily immersion or rinse tanks
• Best suited to small and infrequent cleaning
tasks
• Typical solvent is mineral spirits
• Alternative “solvents” are citric based cleaners
• Waste byproducts may be hazardous
EASA @ 2020 3
Motor Cleaning Methods and Selection Factors June 10, 2020
Solvent Cleaner
Solvent Cleaning
• Declining use due to environmental concerns
(VOCs) and regulations
• Issue of waste disposal
• Health concerns include inhalation and skin
contact
EASA @ 2020 4
Motor Cleaning Methods and Selection Factors June 10, 2020
Aqueous Cleaning Overview
• Most common methods are steam cleaning
and parts washing machines
• Better for human health and the environment
than solvents
• Waste byproduct disposal is still an issue
Steam Cleaning
• Labor intensive: operator is working all the
time
• Pressurized hot water and soap solution is an
effective cleaner
– A time proven technology
– Typical nozzle pressure 90 psi (620 kPa)
• Heating coil can become clogged, and is costly
to replace
– Softening the water extends coil life
10
EASA @ 2020 5
Motor Cleaning Methods and Selection Factors June 10, 2020
Steam Cleaner Coil
11
Steam Cleaning
• Has been method of choice for moderate
cleaning volume requirements
• Can safely clean windings as well as
mechanical components
– Winding insulation can be affected by soap
– Too much pressure can damage delicate parts
• Some parts can air dry
– Windings should always be baked
12
EASA @ 2020 6
Motor Cleaning Methods and Selection Factors June 10, 2020
Pressure washer (aka power washer)
• Similar to steam cleaning
• Cold water and soap solution
• Typical pressure to 200 psi (1400 kPa)
• Lack of heated solution tends to extend
cleaning time
• Grease and oil removal can be difficult
13
Parts Washing Machines
• Oversimplification: Oversized dishwasher
• On the market for over 30 years
– Environmental regulations spurred interest and
sales
• Water and cleaning detergent use is
minimized
– Cabinet storage basin must be periodically
changed out
• 2 to 6 months typical frequency
• Soap can become ineffective if left unchanged
14
EASA @ 2020 7
Motor Cleaning Methods and Selection Factors June 10, 2020
Parts Washing Machines
• Simple three step process
– Parts loaded in washer cabinet and timer set
– Machine cleans automatically through cycle
– Parts unloaded and dried if necessary
• Typical cleaning cycle time is 20-30 minutes
• Turntable rotates parts through jets of low
pressure cleaning spray
15
Parts Washing Machine
16
EASA @ 2020 8
Motor Cleaning Methods and Selection Factors June 10, 2020
Factors in Machine Cleaning
• Soap compatibility with windings and other
components, e.g., commutators, slip rings
• Wash water temperature and cycle time
• Foaming of soap
– Most soaps contain a defoamer (and rust
inhibitor), but…
– May take several tries to obtain a soap that does
not foam
– Use manufacturer’s recommended soaps first
17
Some Machine Options
• Timers for preset heat-up
– It takes time to heat the cabinet water basin
• Fresh water rinse
• Oil skimmers
• Filters to remove particulates so they don’t
get redeposited on parts
• Thermal insulation of the cabinet to retain
heat and reduce energy consumption
18
EASA @ 2020 9
Motor Cleaning Methods and Selection Factors June 10, 2020
Ultrasonic Systems
• Principles of operation
– Ultrasonic waves in a liquid remove deposits
– Typical wave frequency is 28 kHz to 50 kHz
– Imploding bubbles (cavitation) strike surfaces to
create cleaning action
– Detergent allows bubbles to grow faster
– Heat promotes bubble formation and implosion
rate
– Particularly effective on parts with complex
geometries and passages
• Armatures
• Parts with blind holes
19
Ultrasonic Cleaner
20
EASA @ 2020 10
Motor Cleaning Methods and Selection Factors June 10, 2020
Enzyme Systems (Bioremediation)
• Principles of operation
– Microbes are added to break down contaminants into
carbon dioxide and water
– Microbes “eat” the oil and contaminants, i.e.,
bioremediation
– Cleaning solution emulsifies grease and oil
• Considerations
– Generally smaller rinse basin units
– Enzyme formulation well suited to removing oily residue
– Cleaning bath can last indefinitely
– Relatively economical system
21
Other Cleaning Methods
• More aggressive than conventional cleaning,
e.g., abrasive methods
• These include:
– Pyrolysis (burnout oven)
– Carbon dioxide (dry ice)
– Grit blasting
– Water blasting
22
EASA @ 2020 11
Motor Cleaning Methods and Selection Factors June 10, 2020
Pyrolysis Cleaning
• Burnout process may be capable of more than
breaking down winding insulation
• Can be used to remove contaminants or
coatings
• Oven must be designed for the purpose
• Environmental regulations must be followed,
e.g., air permits
23
Pyrolysis Cleaning
• Some process ideas are ill-advised
– Varnish laden bake oven trays
– Parts with heavy paint accumulation
– Large volumes of trade or lead wire
• Sheer volume of combustibles may be too
great for oven
• Follow oven manufacturer’s instructions and
recommendations
24
EASA @ 2020 12
Motor Cleaning Methods and Selection Factors June 10, 2020
Pyrolysis Cleaning
• Oven damage and fines are costly
• Pyrolysis does significantly reduce the volume
of waste byproduct
• Waste byproduct must be lab tested for
regulated hazardous substance content
25
Carbon Dioxide (Dry Ice) Cleaning
• A cryogenic method using CO2 – dry ice
– Dry ice pellets dispensed in pressurized stream of
nitrogen gas
– Dry ice sublimates (changes) from solid to gas upon
impact
– Can be mildly abrasive but leaves no residue
(evaporates)
– Waste byproduct may contain hazardous substances
• Well suited to in-place cleaning of large
apparatus, e.g., generators and motors
– Purchase price of system is very high
• More practical for most to hire a dry ice cleaning firm
26
EASA @ 2020 13
Motor Cleaning Methods and Selection Factors June 10, 2020
Dry Ice Cleaning
27
Grit Blasting
• Abrasive media dispensed in high pressure air
stream
• More aggressive materials:
– Silicon sand, steel grit, aluminum oxide
• Moderate abrasives:
– Glass beads, steel shot, plastic, corncobs
• Air permits usually required due to use of
control equipment
28
EASA @ 2020 14
Motor Cleaning Methods and Selection Factors June 10, 2020
Grit Blasting
• Well suited to cleaning metal parts
• Can easily damage windings or other delicate
parts
• Waste byproduct, and abrasive itself may be
composed of hazardous substances
• Blast cabinets are relatively expensive
– Attendant may be required for blast rooms
29
Water Blasting
• Directs a 15000 to 40000 psi (100 to 275 mPa)
stream of water at parts to be cleaned
– The water can remove:
Dirt Heavy corrosion
Oil Paint – layer by layer
– Aggressive action can be controlled
• Amortisseur bars can be cleaned to bare metal without
harming field coil windings
– Abrasives can be added to make cleaning more aggressive,
e.g. , to:
• Remove scale from pump casings
• Remove wedges and cut through insulation to “cold strip”
windings
30
EASA @ 2020 15
Motor Cleaning Methods and Selection Factors June 10, 2020
Water Blasting
• Cleaner alternative to grit blasting
– No dust – water retains the particles
– Can be used with a steam booth to control
overspray
• Environmental permits for steam booth may
also be applicable to water blaster
• Relative cost is very high
• Safety concerns
– Can literally slice through flesh
– Extremely noisy when contacting blind holes
31
Water Blaster
32
EASA @ 2020 16
Motor Cleaning Methods and Selection Factors June 10, 2020
Aqueous Cleaning Agents
• An expanded discussion as water is common
to so many cleaning methods
• Selection of aqueous cleaning agents
(cleaners)
• Disposal of aqueous cleaning byproducts
33
Selection of Aqueous Cleaners
• Inappropriate cleaner can leave electrically
conductive crystalline deposits on windings
– Acceptable chemical or soap cleaner should be
rinseable and nonconductive
– Seek washing equipment manufacturer’s advice first
• Your primary interests:
– Cleaner’s ability to clean parts
– Prevent winding damage
– Avoid degrading delicate components
• Manufacturer’s primary interests:
– A cleaner that is compatible with the equipment
– Avoid rust or scale buildup
34
EASA @ 2020 17
Motor Cleaning Methods and Selection Factors June 10, 2020
Selection of Aqueous Cleaners
• Environmental issues
– Cleaners with no hazardous components
identified on their MSDS are preferred
– Environmental hazards can affect people as well as
the environment, e.g., by inhalation or skin
contact
• Safety concerns
– The lesser the degree of personal protective
equipment (PPE) required the more desirable
– Cleaners that are neutral or only slightly alkaline
are preferred
35
Disposal of Aqueous Cleaning Byproducts
• Address disposal issues before purchasing or
activating cleaning equipment
• Remember “cradle to grave” liability when
choosing and using a waste disposal firm
• Wastewater disposal directly to sewer is
usually not permissible
– A filter may be required
– Obtain waste authority approval to discharge to
sewer
– You may have to have all wastewater handled by a
disposal firm
36
EASA @ 2020 18
Motor Cleaning Methods and Selection Factors June 10, 2020
Disposal of Byproducts
• Filters can extend life of cleaning solution
• Precleaning parts by manually removing
excess grime is an even better way of
extending cleaning solution life
• Excess grime may be a regulated waste
• An oil water separator extends cleaning
solution life
– May be a requirement for discharge to sewer
– Avoids waste “meatballs” and associated fines and
negative publicity
37
If You Can’t Discharge to Sewer
• Changeout is typically into drums that are
taken away by a waste disposal firm
• Waste reduction techniques:
– Consider allowing contents to settle and extract
clarified solution for reuse
– Commercial evaporator systems are available to
boil off water
• Check with environmental authorities before
trying to use reduction techniques
– May be a prohibited form of “treatment”
– May be a regulated form of “recycling”
38
EASA @ 2020 19
Motor Cleaning Methods and Selection Factors June 10, 2020
If You Can’t Discharge to Sewer
• Wastewater may not be hazardous
– Have a representative sample tested by an
environmental laboratory
– Work with your disposal firm on this
– You may not have to test every time you dispose
• Exercise caution and follow the environmental
regulations to avoid
– Fines
– Negative publicity
– Potential criminal prosecution
39
How to ask questions
Joined using web browser Joined using web browser
+ Zoom plugin
When prompted, reconfirm
Wait to Submit the audio source you’re using
be called written
on question
Ask
question Ask question verbally
verbally
40
EASA @ 2020 20
Motor Cleaning Methods and Selection Factors June 10, 2020
Next webinar
Pump Reliability Essentials
Wednesday, July 15, 2020
12:00pm – 1:00pm CDT
Presented by Gene Vogel
EASA Pump & Vibration Specialist
41
Survey / Recording
Tomorrow, you will be emailed:
• A link to a survey if you would like to provide
feedback.
• A link to a recording of this presentation.
42
EASA @ 2020 21
