Welotec - TK800 Router Series Manual
1) Go via the menu item network to the submenu cellular.
2) Select the cellular tab
Welotec GmbH • [Link] • info@[Link] Page 20 of 168 pages
Welotec - TK800 Router Series Manual Welotec - TK800 Router Series Manual
Default factory settings [Link]
iP: [Link]
Net mask: [Link] 2.12.1. Automatic monitoring of the router
username: adm
Password: 123456
Serial parameter: 115200-N-8-1
ICMP Ping
2.11.2. Web method
1) Via the administration menu, go to the submenu Config Management:
INTERNET
TK800
TK800 Router ICMP Detection Server
ICMP Antwort
Internetverbindung besteht
2) Click Restore Default Configuration to reset the TK800 to its default settings. After a few seconds you will receive the following message. ICMP Ping
The router is now successfully reset.
(schlägt fehl)
3) After a click on reboot the router restarts and is in factory settings.
INTERNET
TK800
TK800 Router
ICMP Detection Server
Watchdog greift
The watchdog monitors the router for internet connection. The router itself checks whether an internet connection is available as desired. For
this, it sends ICMP packets to an individually defined server (ICMP detection server). If this query fails, the router will automatically restart the
dial-up, then the modem, and if necessary the entire system. The watchdog provides a reliable internet connection in the mobile network. This
ensures that the router is almost always reachable.
Welotec GmbH • [Link] • info@[Link] Page 18 of 168 pages Welotec GmbH • [Link] • info@[Link] Page 19 of 168 pages
Welotec - TK800 Router Series Manual Welotec - TK800 Router Series Manual
signal strength
[Link] to factory settings
Signal: 1-9 2.11.1. Hardware method
(bad signal, the router cannot operate properly. Please check the antenna
connection and the local signal strength of the mobile network.) explanation of symbols
= LED on = LED off = LED flashing
Signal: 10-19
(router is operating normally)
1) Press the ReSeT button while turning the TK800 on:
Signal: 20-31 STATUS WARN
(perfect signal level)
PWR ERR
RESET
2) As soon as the eRRoR LeD lights up (approx. 10 seconds after switching on), release the ReSeT button:
STATUS WARN
PWR ERR
RESET
3) After a few seconds, the ERROR LED will no longer light up. Now press the RESET button again until the Error light flashes and then release
the button:
STATUS WARN
PWR ERR
RESET
4) Now the LED lights ERROR and STATUS are flashing, which means that the reset to the default setting was successful.
STATUS WARN
PWR ERR
RESET
Welotec GmbH • [Link] • info@[Link] Page 16 of 168 pages Welotec GmbH • [Link] • info@[Link] Page 17 of 168 pages
Welotec - TK800 Router Series Manual Welotec - TK800 Router Series Manual
2.9.2. Manual configuration [Link] status lights
Configure your PC to be located in the same subnet as the router ([Link]). The subnet mask must be [Link]. The following explanation of symbols
figure shows the procedure for configuring the IP address on a PC with the Windows 10 operating system.
= LED on = LED off = LED flashing
There are two SiM card LeDs. When the router starts up, the SiM card LeD for SiM card 1 lights up; in all other cases, the SiM card reception
indicator lights up:
System start: System start successful:
STATUS WARN STATUS WARN
PWR ERR PWR ERR
After configuring the IP address of the PC and connecting to the router, open a web browser. SIM SIM
Then enter „[Link] in the address bar of your browser. After confirming with the „Enter“ key a pop-up window appears as login
page of the router. enter the user name (default:“adm“) and the password (default:“123456“) and confirm with „Enter“. Now you will be
1 2 VPN 1 2 VPN
redirected to the configuration website. Configure the router according to your requirements.
To check if you are connected to the internet, select network > cellular > status from the navigation panel. Here you can see the data of the
MODEM MODEM
mobile radio unit in the router. Alternatively, just open a webpage in your browser.
iP: [Link] Dialing: Dialing successful:
username: adm
Password: 123456
STATUS WARN STATUS WARN
PWR ERR PWR ERR
SIM SIM
1 2 VPN 1 2 VPN
MODEM MODEM
Reset successful: Firmware update:
STATUS WARN STATUS WARN
PWR ERR PWR ERR
SIM SIM
1 2 VPN 1 2 VPN
MODEM MODEM
Welotec GmbH • [Link] • info@[Link] Page 14 of 168 pages Welotec GmbH • [Link] • info@[Link] Page 15 of 168 pages
Welotec - TK800 Router Series Manual Welotec - TK800 Router Series Manual
2.6. Installation of the power supply 2.9. setting up the router
Remove the terminal block from the top of the router. Loosen the relevant screws on the terminal block and lead the cores to the correspon-
ding terminals. The terminals are marked accordingly on the top of the router. Tighten the screws again and then reinsert the connector block 2.9.1. Automatic Configuration (DHCP)
into the router.
Configure the PC so that it works as a DHCP client (obtain IP address automatically). Connect the PC to the FE0/2 or FE1/1 - FE1/4 interface
use the grounding screw on the unit to ground the unit. (only TK8X5 variants) using a network cable. The router assigns IP address, default gateway and DNS server to the PC. The following figure
shows the configuration process via DHCP on a PC with the Windows 10 operating system, which can be accessed via the Network and Sha-
ring Center in Windows 10.
To eliminate electromagnetic interference, the housing of the router must be earthed via the grounding screw.
2.7. cable connections
Connect the router to your PC via a network cable (RJ45). We recommend the Fe 0/2 port for all TK8x2 models and the Fe 1/4 port for all
TK8x5 models.
2.8. connection of serial interfaces and I/os
To connect the serial interfaces and the I/Os, you will find a connection block on the front panel of the device. The individual contacts for this
are marked on the front of the device. Connect the cables according to these labels. The contact „iN“ represents the digital input here, while
the output is labeled „Relay“. „CoM“ represents the ground. During installation, remove the connection block from the device and connect the
individual cores to the corresponding terminals. Then plug the terminal block back into the device.
Terminal screws
After configuring the IP address of the PC and connecting to the router, open a web browser.
RXD
Then enter „[Link] in the address bar of your browser (e. g. Google Chrome). After confirming with the „Enter“ key, a pop-up
TXD
window appears as login page of the router. enter the user name (default:“adm“) and the password (default:“123456“) and confirm with
GND „Enter“. Now you will be redirected to the configuration website. Configure the router according to your requirements.
A(RS-485+) To check if you are connected to the internet, select network > cellular > status from the navigation panel. Here you can see the data of the
mobile radio unit in the router. Alternatively, just open a webpage in your browser.
B(RS-485-)
IN
COM
iP: [Link]
username: adm
RELAY
Password: 123456
This chapter only describes routers with serial interfaces and i/o‘s TK8XXX-eX.
Welotec GmbH • [Link] • info@[Link] Page 12 of 168 pages Welotec GmbH • [Link] • info@[Link] Page 13 of 168 pages
Welotec - TK800 Router Series Manual Welotec - TK800 Router Series Manual
2.3. Installation guide 2.4. Installing the sIM card
The TK800 supports dual SiM. To insert the cards, press the yellow „eject“ button e. g. with a small screwdriver on top of the device. The respec-
2.3.1. Preparations tive SiM card slot is pressed out. if the TK800 is not operated in dual SiM mode, use the SiM card slot „SiM1“.
Then insert the SiM card. The SiM card slot is not hot-plug capable. The router must be restarted after inserting the SiM card.
Prepare the power supply (12 - 48 V DC). Ensure that the device can operate under the specified ambient conditions (operating temperature
range -25 - +70 °C, humidity: 5 - 95 % relative humidity). The device should not be exposed to direct sunlight and should be installed separa-
tely from heat sources and environments with strong electromagnetic interference. The router can be mounted on a DiN rail (mounting rail) or
used at the workplace.
2.3.2. Mounting the device
Mounting rail:
Select a location with enough space on the mounting rail. Then place the upper part of the mounting on the mounting rail. Afterwards, press
the lower side of the mounting rail receptacle downward until the device is locked. This is illustrated in this image:
2.5. Installation of the antennas
Plug the antennas into the SMA connectors and turn the outer mounting on the antenna cable until the connection is secure.
For optimal performance, the antennas should be placed at least 20 cm apart from each other.
2
To disassemble press the device from the top toward the bottom, and then pull the bottom side of the device from the mounting rail (see
Figure).
Welotec GmbH • [Link] • info@[Link] Page 10 of 168 pages Welotec GmbH • [Link] • info@[Link] Page 11 of 168 pages
