PRODUCT DATA SHEET
SikaGrout®-215 M
HIGH STRENGTH, NON-SHRINK CEMENTITIOUS GROUT FOR MARINE STRUCTURE AND CON-
CRETE REPAIR
DESCRIPTION
CHARACTERISTICS / ADVANTAGES
A non-shrink, cementitious grout, specially developed
for marine environment structure and concrete repair. ▪ Easy to use, just add water.
With a special blend of shrinkage-reducing and plasti- ▪ Adjustable consistency.
cizing/water-reducing agent, SikaGrout®-215 M is a ▪ Excellent resistant to salt water and oil.
shrinkage compensated material. ▪ High final strength.
▪ Impact resistant.
USES ▪ Shrinkage compensated.
▪ Non-flammable, non-toxic, and non-corrosive.
▪ For structural repair, especially in marine environ- ▪ Marine structure: Also recomended for repairing
mental such as honeycombing, spalling of column, structure underwater and in tidal zone grouting with
beam, precast wall panel and structural members. high strength requirement.
▪ For structural grouting of column and machine base ▪ Repair application of : - Bridge piers,
plates, anchor rods, bearing plates, precast wall pan- - Concrete Piles,
el flow. - Harbour walls,
- Jetty Pillars.
PRODUCT INFORMATION
Packaging 25 kg bag
Appearance / Colour Powder / Grey
Shelf life 6 months from date of production if stored in undamage and unopened
original sealed bags
Storage conditions Store in dry condition between +10 °C - +30 °C
Density ~2.18 kg/L
Product Data Sheet
SikaGrout®-215 M
June 2020, Version 03.01
020201010010000063
1/3
TECHNICAL INFORMATION
Compressive Strength 1 day ~28.0 N/mm2 (ASTM C-109)
3 days ~45.0 N/mm2
7 days ~62.0 N/mm2
28 days ~73.0 N/mm2
Tensile Strength in Flexure 28 days >8.0 N/mm2 (ASTM C-348)
Tensile Adhesion Strength 28 days ~1.5 N/mm2
Concrete failure, over roughened
concrete surface
28 days ~2.5 N/mm2
Over mechanically roughened old
grout surface
Expansion 1 - 3 h (at +27 °C) 0.30 - 1.40 % (ASTM C-940)
APPLICATION INFORMATION
Mixing Ratio 4.25 L per 25 kg bag (water per powder = 17 % by weight)
Consumption ~1 880 kg/m3 of mortar.
Yield 13.30 L per 25 kg bag
Layer Thickness Recommended thickness is 20 - 100 mm
Flowability Flow cone (mm) ≥ 200 mm (ASTM C230/230M)
Product Temperature < +30 °C, max.
Ambient Air Temperature +10 °C - +35 °C
Substrate Temperature +10 °C - +35 °C
Pot Life 25 min
Setting Time 4 - 6 hours
APPLICATION INSTRUCTIONS MIXING
SUBSTRATE QUALITY / PRE-TREATMENT Put the measured quantity of water (depends on the
required consistency) into a mixing vessel. add slowly
SURFACE PREPARATION the total contents of SikaGrout®-215 M while mixing.
▪ Surface must be clean and free oil of all dirt, oil, Mix continuosly for 3 minutes to achieve an even con-
grease, cement laitance, loose material and other sistency. Use a mechanically low speed drill (400-600
bond-inhibition materials. rpm) with mixing paddle or in appropriately sized mor-
▪ Concrete must be sound and roughened to promote
tar mixer.
mechanical adhesion.
▪ Prior to pouring, surface must be well wetted to sat- APPLICATION
urated surface dry.
Within 25 minutes after mixing, place grout into forms
FORMING from one side to avoid air entrapment. Do not vibrate.
For flowable grout, construct forms to retain grout Use a suitable head box of 150-200 mm and maintain
without leakage. Forms should be lined or coated with the grout head all times to ensure a continuous flow.
bond-breaker for easy removal. If tight form is dificult Gentle tapping or pulling loops of wire from one side
to achieve, use SikaSet Accelarator as water plug may assist the flow of the mortar under difficult work-
(refer to PDS SikaSet Accelarator). ing condition.
Product Data Sheet
SikaGrout®-215 M
June 2020, Version 03.01
020201010010000063
2/3
CURING TREATMENT LOCAL RESTRICTIONS
Wet cure for a minimum of 3 days with wet hessian,
plastic sheet or apply a curring compound (Antisol). Note that as a result of specific local regulations the
declared data and recommended uses for this product
CLEANING OF EQUIPMENT may vary from country to country. Consult the local
Product Data Sheet for the exact product data and
Clean all tools and application equipment with water uses.
immediately after use. Hardener and/or cured materi-
al can only be remove mechanically. ECOLOGY, HEALTH AND SAFETY
IMPORTANT CONSIDERATIONS For information and advice on the safe handling, stor-
age and disposal of chemical products, users shall
▪ Minimum application thinkness : 10 mm refer to the most recent Safety Data Sheet (SDS) con-
▪ Recommended thinkness of SikaGrout®-215 M in taining physical, ecological, toxicological and other
one pour is 20 mm to 100 mm. If the thinkness ex- safety-related data.
ceeds 100 mm, special procedure must be taken to
anticipate temperature rise. Iced water, add coarse LEGAL NOTES
aggregate to the mix (max. 40% by powder weight),
or both of them may be used to eliminate temperat- The information, and, in particular, the recommenda-
ure rise. tions relating to the application and end-use of Sika
▪ Variations in cement could cause shade differences products, are given in good faith based on Sika's cur-
in colour of the mortar. rent knowledge and experience of the products when
properly stored, handled and applied under normal
BASIS OF PRODUCT DATA conditions in accordance with Sika's recommenda-
tions. In practice, the differences in materials, sub-
All technical data stated in this Data Sheet are based strates and actual site conditions are such that no war-
on laboratory tests. Actual measured data may vary ranty in respect of merchantability or of fitness for a
due to circumstances beyond our control. particular purpose, nor any liability arising out of any
legal relationship whatsoever, can be inferred either
from this information, or from any written recom-
mendations, or from any other advice offered. The
user of the product must test the product’s suitability
for the intended application and purpose. Sika re-
serves the right to change the properties of its
products. The proprietary rights of third parties must
be observed. All orders are accepted subject to our
current terms of sale and delivery. Users must always
refer to the most recent issue of the local Product
Data Sheet for the product concerned, copies of which
will be supplied on request.
PT. Sika Indonesia Head Office and
Manufacturing
Jl. Raya Cibinong-Bekasi Km.20
Limusnunggal-Cileungsi
Bogor 16820-Indonesia
Tel. +62 21 8230025, Fax +62 21
8230026
SikaGrout-215M-en-ID-(06-2020)-[Link]
Product Data Sheet
SikaGrout®-215 M
June 2020, Version 03.01
020201010010000063
3/3
