SIL-C

Line, Feeder & Generator Protection Relay

Primary & Secondary Distribution Protection

• The SIL-C is a feeder relay with current, voltage and frequency functions • Synchronization through IRIG-B optional depending on model.
for primary and secondary distribution with auxiliary power supply of • The SIL-C is provided with 11 configurable inputs and 5 configurable
24- 230 Vdc/ac. outputs.
• 4 current channels and up to 5 voltage channels for conventional VTs. • The SIL-C is fitted with the demand of power (Load Data Profiling) with
• Capability of measuring up to 1.000 volts when it is connected directly the following characteristics:
to the low voltage line. » Number of records: 2160.
• Metallic box with high electromagnetic compatibility level (EMC) and » Recording mode circular.
wide range of operating temperature. » Sampling rate (interval): configurable through communications
• Protection of decoupling, load shedding and loss of main (islanding). (1-60 min).
Loss of Main (islanding) occurs when part of the public utility network • Alarms panel is available.
loses connection with the rest of the system. If this situation is not • SIL-C is provided with non-volatile RAM memory in order to store up to
detected, then the generator could remain connected, causing a safety 3072 events and disturbance fault recording (DFR), maintaining date &
hazard within the network. Automatic reconnection of the generator time thanks to its internal RTC (real Time Clock).
to the network may occur causing damage to the generator and the » 5 records in data and COMTRADE format (300 cycles each
network. SIL-C protection relay detects this situation thanks to its record): 1 to 8 pre-fault cycles + 292 to 299 postfault cycles.
voltage and frequency functions focused on the Rate of change of » 25 records in data and COMTRADE format (60 cycles each
frequency (ROCOF) method. record): 1 to 8 pre-fault cycles + 52 to 59 postfault cycles.
• Signaling/control of the circuit breaker (52 function) and the recloser » 50 records in data and COMTRADE format (30 cycles each
(79 function). record): 1 to 8 pre-fault cycles + 22 to 29 postfault cycles.
• In case a CB is manually closed, a switch on to an existing fault may » 100 records in data and COMTRADE format (15 cycles each
occur. This fault condition is critical if the overcurrent protection function record): 1 to 8 pre-fault cycles + 7 to 14 postfault cycles.)
does not clear the fault until the adjusted time delay is finished. It is • Each oscillographic record contains 10 analogue channels and up to
necessary, in those cases, to clear the fault quickly by means of SOTF 96 configurable digital channels. The oscillography is downloaded by
function. communications port. The SICom communications program allows
• To allow the communication, relays are provided with a local micro USB the oscillography record to be downloaded and saved in COMTRADE
front port and with remote communication with different options (ports format (IEEE C37.111-1991).
and protocols) on the rear side:
» Rear RS485 Port: IEC60870-5-103, Modbus RTU or DNP3.0
Serial (selectable by general settings).
» Rear RJ45 Port: Modbus TCP/IP, DNP3.0 TCP/IP or IEC60870-
5-104 (selectable by general settings) + SNTP Protocol + Web
Server.

82
Functions diagram SIL-C

BUS SIL-C

3 or 4
27 27V1 59 59N/G 47 24 81 81R 78

32 60VTS

3
67NI 67N/51N 67/51 SOFT 50 50N 46 46BC 37 49 SHB

60CTS
AFD* 64REF

1 67GI 67G/51G 50BF

50G

CLP

52
HLT 79 52 74TCS 68 86 25*

3
27-L* 59-L*

49T

tº SER ALRM PGC HMI LDP DFR

RTC MET STTG CMMD CNT

LINE

1 1 1 1 * Optional

IRG-B* ETHERNET* RS485* USB

ANSI CODE PROTECTIONS

50 Instantaneous phase overcurrent 27 Instantaneous Phase undervoltage (Bus Bar)
67/51 Inverse Time Directional* Phase Overcurrent 27L Instantaneous phase undervoltage (Line)
50N Instantaneous calculated neutral overcurrent Instantaneous Positive sequence undervoltage (Bus
27V1
Bar)
50G Instantaneous measured neutral overcurrent 32 Directional Overpower
67N/51N Inverse Time Directional* Calculated Neutral
Overcurrent 81O/U Under/Overfrequency

67G/51G Inverse Time Directional* Measured Neutral 81R Rate of change of Frequency (ROCOF)
Overcurrent
78 Out of Step (Vector Shift)
67NI Directional isolated calculated neutral overcurrent
24 Overfluxing
67GI Directional isolated measured neutral overcurrent
CLP Cold Load pickup
SOTF Switch On To Fault
79 AC Reclosing device
46 Phase balance current protection
HLT Hot Line Tag
46BC Broken Conductor Detection
52 Breaker Wear Monitoring
64REF Restricted earth fault
25 Synchro Check
37 Instantaneous phase undercurrent
50BF Circuit Breaker Failure
49 Thermal overload
74TCS Trip Circuit Supervision
49T External Trip
60CTS Phase CT Supervision
SHB Second Harmonic Blocking
60VTS Phase VT Supervision
59 Instantaneous phase overvoltage (Bus Bar)
Instantaneous Calculated/Measured neutral 86 Trip Lockout
59N/G overvoltage (Bus Bar)
68 Zone Selection Interlocking (ZSI)
59L Instantaneous phase overvoltage (Line)
PGC Programmable logic control
47 Phase Balance voltage protection (Bus Bar) * ANSI 67, ANSI 67G and ANSI 67N can be converted into ANSI 51,
ANSI 51G and ANSI 51N respectively by setting the “Directionality”
parameter to NO.
ADDITIONAL FUNCTIONS
SER Sequential Event Recording
CNT Counters
DFR Disturbance Fault Recording
RTC Real Time Clock
LDP Load Data Profiling
ALRM Alarm panel
MET Metering
PGC Programmable Logic Control
STTG Settings Groups
HMI Human Machine Interface
CMMD Commands

83
Technical parameters SIL-C

Function enable: No/Alarm/Trip/SHB Trip Function enable: No/Alarm/Trip/SHB Trip

Current tap: 0.010 to 30.000 xIn (step 0.001xIn) Curve Type: IEC 60255-151 and IEEE curves.
Time delay: 0.000 to 300.000 s (step 0.001 s)
Function 50-1 IEC (Definite time, standard inverse, very inverse,
Activation level: 100% extremely inverse, long-time inverse, short time
Function 50-2 inverse) and IEEE (Moderately inverse, very inverse,
Deactivation level: 95%
extremely inverse).
Temporized deactivation
Time delay: 0.000 to 300.000 s (step 0.001 s)
Timing accuracy: ± 35 ms or ± 0.5% (greater of both) Time dial (TMS): 0.05 to 25.00 (step 0.01)
Function enable: No/Alarm/Trip/SHB Trip
If Curve type IEC: 0.05 to 1.00 (step 0.01)
Current tap: 0.050 to 30.000 xIn (step 0.001xIn)
Time delay: 0.000 to 300.000 s (step 0.001 s) If Curve type IEEE: 0.10 to 25.00 (step
Function 50N-1 Activation level: 100% 0.01)

Deactivation level: 95% Current tap: 0.050 to 20.000 xIn (step 0.001xIn)

Temporized deactivation Directionality: No/Forward/Reverse

Function 67N/51N-1
Timing accuracy: ± 35 ms or ± 0.5% (greater of both) Polarization voltage: 0.08 to 2.00 xUn (step 0.01xUn)
Function 67N/51N-2 Operating angle: 0 to 359º (step 1º)
Function enable: No/Alarm/Trip/SHB Trip
Current tap: 0.010 to 30.000 xIn (step 0.001xIn) Halfcone angle: 10 to 170º (step 1º)

Time delay: 0.000 to 300.000 s (step 0.001 s) Curve, current activation level: 110%

Function 50G-1 Activation level: 100% Curve, current deactivation level: 100%

Deactivation level: 95% Defined time, current activation level: 100%

Temporized deactivation Defined time, current deactivation level: 95%

Voltage activation level: 100%
Timing accuracy: ± 35 ms or ± 0.5% (greater of both)
Voltage deactivation level: 95%
Function enable: No/Alarm/Trip/SHB Trip
Temporized deactivation
Curve Type: IEC 60255-151 and IEEE curves.
Timing accuracy for IEC and IEEE curves selection:
IEC (Definite time, standard inverse, very inverse,
extremely inverse, long-time inverse, short time ± 30 ms or ± 5% (greater of both)
inverse) and IEEE (Moderately inverse, very inverse,
extremely inverse). Timing accuracy for defined time curve selection:
Time delay: 0.000 to 300.000 s (step 0.001 s)
± 35 ms or ± 0.5% (greater of both)
Time dial (TMS): 0.05 to 25.00 (step 0.01)

If Curve type IEC: 0.05 to 1.00 (step 0.01)

If Curve type IEEE: 0.10 to 25.00 (step

0.01)
Current tap: 0.010 to 20.000 xIn (step 0.001xIn)
Function 67/51-1
Directionality: No/Forward/Reverse
Function 67/51-2 Polarization voltage: 0.08 to 2.00 xUn (step 0.01xUn)
Operating angle: 0 to 359º (step 1º)
Function 67/51-3
Halfcone angle: 10 to 170º (step 1º)
Function 67/51-4 Curve, current activation level: 110%
Curve, current deactivation level: 100%
Defined time, current activation level: 100%
Defined time, current deactivation level: 95%
Voltage activation level: 100%
Voltage deactivation level: 95%
Temporized deactivation
Timing accuracy for IEC and IEEE curves selection:

± 30 ms or ± 5% (greater of both)

Timing accuracy for defined time curve selection:

± 35 ms or ± 0.5% (greater of both)

84
Technical parameters SIL-C

Function enable: No/Alarm/Trip/SHB Trip Function enable: No/Alarm/Trip/SHB Trip

Curve Type: IEC 60255-151 and IEEE curves. Directionality: No/Forward/Reverse
IEC (Definite time, standard inverse, very inverse, Low Current Tap: 0.010 to 30.000 xIn (step 0.001xIn)
extremely inverse, long-time inverse, short time
inverse) and IEEE (Moderately inverse, very inverse, High Current Tap: 0.010 to 30.000 xIn (step
extremely inverse). 0.001xIn)

Time delay: 0.000 to 300.000 s (step 0.001 s) Low Voltage Tap: 0.08 to 2.00 xUn (step 0.01xUn)

Time dial (TMS): 0.05 to 25.00 (step 0.01) High Voltage tap: 0.08 to 2.00 xUn (step 0.01xUn)
Function 67GI
If Curve type IEC: 0.05 to 1.00 (step 0.01) Time delay: 0.000 to 300.000 s (step 0.001 s)
If Curve type IEEE: 0.10 to 25.00 (step Operating angle: 0 to 359º (step 1º)
0.01)
Halfcone angle: 10 to 170º (step 1º)
Current tap: 0.010 to 20.000 xIn (step 0.001xIn)
Activation level: 100%
Directionality: No/Forward/Reverse
Deactivation level: 95%
Function 67G/51G-1 Polarization voltage: 0.08 to 2.00 xUn (step 0.01xUn)
Temporized deactivation
Operating angle: 0 to 359º (step 1º)
Function 67G/51G-2 Timing accuracy: ± 30 ms or ± 5% (greater of both)
Halfcone angle: 10 to 170º (step 1º)
Function enable: No/Alarm/Trip/ SHB Trip
Curve, current activation level: 110%
Current tap: 0.050 to 20.000 xIn (step 0.001xIn)
Curve, current deactivation level: 100%
Time delay: 0.020 to 300.000 s (step 0.001 s)
Defined time, current activation level: 100% Function 64REF Neutral SHB Tap: 5 to 50% (step 1%)
Defined time, current deactivation level: 95%
Activation level: 100%
Voltage activation level: 100%
Deactivation level: 95%
Voltage deactivation level: 95%
Temporized deactivation
Temporized deactivation
Timing accuracy: ± 35 ms or ± 5% (greater of both)
Timing accuracy for IEC and IEEE curves selection:
Function enable: No/Alarm/Trip/SHB Trip
± 30 ms or ± 5% (greater of both)
Current tap: 0.010 to 30.000 xIn (step 0.001xIn)
Timing accuracy for defined time curve selection:
Time delay: 0.000 to 295.000 s (step 0.001 s)
± 35 ms or ± 0.5% (greater of both)
Safe Time: 0.020 to 300.000 s (step 0.001 s)
Function enable: No/Alarm/Trip/SHB Trip Function SOTF
Activation level: 100%
Directionality: No/Forward/Reverse
Deactivation level: 95%
Low Current Tap: 0.050 to 30.000 xIn (step 0.001xIn)
Temporized deactivation
High Current Tap: 0.050 to 30.000 xIn (step
0.001xIn) Timing accuracy: ± 35 ms or ± 0.5% (greater of both)
Low Voltage Tap: 0.08 to 2.00 xUn (step 0.01xUn) Function enable: No/Alarm/Trip
High Voltage tap: 0.08 to 2.00 xUn (step 0.01xUn) Current tap: 0.100 to 2.400 In (step 0.001xIn)
Function 67NI ζ heating: 3 to 600 min (step 1 min)
Time delay: 0.000 to 300.000 s (step 0.001 s)
Operating angle: 0 to 359º (step 1º) ζ cooling: 1 to 6 xζ heating (step 1)
Function 49
Halfcone angle: 10 to 170º (step 1º) Alarm: 20 to 99% (step 1%)
Activation level: 100% Trip level: 100%
Deactivation level: 95% Deactivation level: 95% of alarm level
Temporized deactivation Timing accuracy: ± 5% respect of theorical value.
Timing accuracy: ± 30 ms or ± 5% (greater of both) Function enable: No/Yes
Current Tap: 5 to 50% (step 1%)
Reset Time: 0.000 to 300.000 (step 0.001 s)
Function SHB Block Threshold: 0.010 to 30.000xIn (step 0.001xIn)
Activation level: 100%
Deactivation level: 95%
Temporized deactivation
Function enable: Yes/No
Settings group: 1 to 4 (step 1)
No load time: 0.020 to 300.000 s (step 0.001 s)
Function CLP
Cold load time: 0.020 to 300.000 s (step 0.001 s)
Open breaker activation 0.8% In and reset
threshold: 1% In

85
Technical parameters SIL-C

Function enable: No/Alarm/Trip/SHB Trip Function enable: No/Alarm/Trip

Curve Type: IEC 60255-151 and IEEE curves. Voltage tap: 0.15 to 2.00 xUn (step 0.01xUn)
Minimum level: 0.00 to 1.00 xUn (step 0.01xUn)
IEC (Definite time, standard inverse, very inverse,
extremely inverse, long time inverse, short time Time delay: 0.060 to 300.000 s (step 0.001 s)
inverse) and IEEE (Moderately inverse, very inverse, Reset time: 0.020 to 300.000 s (step 0.001 s)
Function 27V1
extremely inverse).
Activation level: 99%
Time delay: 0.000 to 300.000 s (step 0.001 s)
Deactivation level: 101%
Time dial (TMS): 0.05 to 25.00 (step 0.01)
Temporized deactivation
If Curve type IEC: 0.05 to 1.00 (step 0.01)
Timing accuracy: ± 30 ms or ± 0.5% (greater of both)

If Curve type IEEE: 0.10 to 25.00 (step Function enable: No/Alarm/Trip

0.01) Voltage tap: 0.08 to 2.00 xUn (step 0.01xUn)
Function 46 Current tap: 0.050 to 20.000 xIn (step 0.001xIn) Minimum level: 0.00 to 1.00 xUn (step 0.01xUn)
Curve, current activation level: 110% Time delay: 0.060 to 300.000 s (step 0.001 s)
Curve, current deactivation level: 100% Function 27L (*) Reset time: 0.020 to 300.000 s (step 0.001 s)
Defined time, current activation level: 100% Activation level: 99%
Defined time, current deactivation level: 95% Deactivation level: 101%
Temporized deactivation Temporized deactivation
Timing accuracy for IEC and IEEE curves selection: Timing accuracy: ± 30 ms or ± 0.5% (greater of both)

± 30 ms or ± 5% (greater of both) Function enable: No/Alarm/Trip

Voltage tap: 0.08 to 2.00 xUn (step 0.01xUn)
Timing accuracy for defined time curve selection:
Time delay: 0.045 to 300.000 s (step 0.001 s)
± 35 ms or ± 0.5% (greater of both) Function 59-1 Reset time: 0.020 to 300.000 s (step 0.001 s)
Function enable: No/Alarm/Trip Function 59-2 Activation level: 101%
Tap: 15 to 100 % (step 1%) Deactivation level: 99%
Time delay: 0.030 to 300.000 s (step 0.001 s) Temporized deactivation
Function 46BC
Activation level: 100% Timing accuracy: ± 30 ms or ± 0.5% (greater of both)
Deactivation level: 95% Function enable: No/Alarm/Trip
Timing accuracy: ± 30 ms or ± 0.5% (greater of both) Voltage tap: 0.08 to 2.00 xUn (step 0.01xUn)
Function enable: No/Alarm/Trip Time delay: 0.045 to 300.000 s (step 0.001 s)
Current tap: 0.010 to 30.000 xIn (step 0.001xIn) Function 59N/G-1 Reset time: 0.020 to 300.000 s (step 0.001 s)
Minimum level: 0.000 to 1.000 xIn (step 0.001xIn) Function 59N/G-2 Activation level: 101%
Time delay: 0.060 to 300.000 s (step 0.001 s) Deactivation level: 99%
Function 37
Activation level: 100% Temporized deactivation
Deactivation level: 105% Timing accuracy: ± 30 ms or ± 0.5% (greater of both)
Temporized deactivation Function enable: No/Alarm/Trip
Timing accuracy: ± 30 ms or ± 0.5% (greater of both) Voltage tap: 0.08 to 2.00 xUn (step 0.01xUn)
Function enable: No/Alarm/Trip Time delay: 0.045 to 300.000 s (step 0.001 s)
Voltage tap: 0.08 to 2.00 xUn (step 0.01xUn) Reset time: 0.020 to 300.000 s (step 0.001 s)
Function 47
Minimum level: 0.00 to 1.00 xUn (step 0.01xUn) Activation level: 101%
Time delay: 0.060 to 300.000 s (step 0.001 s) Deactivation level: 99%
Function 27-1
Reset time: 0.020 to 300.000 s (step 0.001 s) Temporized deactivation
Function 27-2
Activation level: 99% Timing accuracy: ± 30 ms or ± 0.5% (greater of both)
Deactivation level: 101% Function enable: No/Alarm/Trip
Temporized deactivation Voltage tap: 0.08 to 2.00 xUn (step 0.01xUn)
Timing accuracy: ± 30 ms or ± 0.5% (greater of both) Time delay: 0.045 to 300.000 s (step 0.001 s)
Reset time: 0.020 to 300.000 s (step 0.001 s)
Function 59L (*)
Activation level: 101%
Deactivation level: 99%
Temporized deactivation
Timing accuracy: ± 30 ms or ± 0.5% (greater of both)

86
Technical parameters SIL-C

Function enable: No/Alarm/Trip Function enable: No/Alarm/Trip

Activation level: 0.02 to 2.00 xSn (step 0.01xSn) Curve Type: Inverse A, Inverse B, Inverse C and
Function 32-1 Defined Time.
Operating angle: 0 to 359º (step 1º)
Function 32-2 Time delay: 0.020 to 300.000 s (step 0.001 s) Time delay: 0.020 to 300.000 s (step 0.001 s)
Function 32-3 Activation level: 100% Time dial (TMS): 0.10 to 25.00 (step 0.01)
Deactivation level: 95% Activation level: 0.50 to 2.00 xUn/Fn (step 0.01 xUn/
Function 32-4 Fn)
Instantaneous deactivation
Time delay: 0.020 to 300.000 s (step 0.001 s)
Timing accuracy: ± 30 ms or ± 0.5% (greater of both)
Reset Time: 0.00 to 300.000 s (step 0.001 s)
Function enable: No/Alarm/Trip
Function 24-1
Curve, activation level: 110%
Type: Underfrequency or overfrequency
Function 24-2 Curve, deactivation level: 100%
Activation level: 45.000 to 65.000 Hz (step 0.001 Hz)
Defined time, activation level: 100%
Time delay: 0.020 to 300.000 s (step 0.001 s)
Defined time, deactivation level: 95%
Reset time: 0.020 to 300.000 s (step 0.001 s)
Temporized deactivation
Function 81-1 Function blocked if phase B voltage is lower than 20
volts P-N (35 volts P-P) Timing accuracy for curves selection:
Function 81-2 Activation level: 100%
± 30 ms or ± 5% (greater of both)
Function 81-3 Underfrequency reset level: activation level +
50mHz Timing accuracy for defined time curve selection:
Function 81-4
Overfrequency reset level: activation level - 50 mHz ± 30 ms or ± 0.5% (greater of both)
Temporized deactivation Dead tap: 0.08 to 2.00 xUn (step 0.01xUn)
The frequency measurement is an average value Live tap: 0.08 to 2.00 xUn (step 0.01xUn)
of the frequency measured during 8 cycles. The
accuracy of the Time Delay is the adjusted value Voltage supervision time: 0.060 to 300.000 s (step
plus the necessary time to achieve the measurement 0.001 s)
during 8 cycles.
Voltage difference: 0.05 to 2.00 xUn (step 0.01xUn)
Function enable: No/Alarm/Trip Function 25 (*)
Phase difference: 2 to 90 º (step 1º)
Type: Increase/Decrease
Frequency difference: 0.060 to 10.000 Hz (step
Activation level: 0.100 to 5.000 Hz/s (step 0.001 0.001 Hz)
Hz/s)
Synchro check time: 0.020 to 300.000 s (step 0.001
Function 81R-1 Time delay: 0.060 to 40.000 s (step 0.001 s) s)
Reset time: 0.020 to 300.000 s (step 0.001 s) Number of recloses: 0 to 4 (step 1)
Function 81R-2
Function blocked if phase B voltage is lower than 20 Reclose time 1, 2, 3, 4: 0.020 to 2000.000 s (step
volts P-N (35 volts P-P) 0.001 s)
Function 81R-3
Activation level: 100% Hold Enable: No/Yes/No Time
Function 81R-4
Temporized deactivation Function 79 Hold time: 0.000 to 2000.000 s (step 0.001 s)
The frequency measurement is an average value Reset time: 0.020 to 2000.000 s (step 0.01 s)
of the frequency measured during 8 cycles. The
accuracy of the Time Delay is the adjusted value Safe time: 0.020 to 2000.000 s (step 0.001 s)
plus the necessary time to achieve the measurement
Locking possibilities: pulse inputs, level inputs,
during 8 cycles.
commands.
Function enable: No/Alarm/Trip
Maximum number of openings: 1 to 100,000 (step 1)
Activation level: 1 to 25º (step 1º)
Maximum accumulated amperes: 1 to 100,000
Reset time: 0.020 to 300.000 s (step 0.001 s) M(A2) (step 1)

Function 78 Function blocked if phase B voltage is lower than 20 Repetitive number of openings: 1 to 100,000 (step 1)
volts P-N (35 volts P-P)
Time for repetitive number of openings: 1 to 300 min
Temporized deactivation (step 1 min)

Measurement accuracy: ±1º or ±10% (greater of Function 52 Maximum opening time: 0.020 to 300.000 s (step
both) 0.001 s)
Maximum closing time: 0.020 to 300.000 s (step
0.001 s)
Circuit breaker status monitoring:
Current measurements: Open breaker activation and
reset threshold: 0.8% In (Without using contacts)
Using contacts: 52a or 52b and 52a and 52b

87
Technical parameters SIL-C

Function enable: No/Yes 32 samples/cycle

Time delay: 0.020 to 300.000 s (step 0.001 s) 10 analog channels and 96 configurable digital
Function 74TCS
channels
Continuity in circuits A and B through configurable
inputs Configurable DFR Start
Function enable: No/Yes Configurable number of records depending on the
size:
Time delay: 0.020 to 300.000 s (step 0.001 s)
Timing accuracy: ± 30 ms or ± 0.5% (greater of 5 records in data and COMTRADE format (300
Function 60CTS both) cycles each record): 1 to 8 pre-fault cycles + 292 to
299 postfault cycles.
Open breaker activation and reset threshold: 0.8%
In
25 records in data and COMTRADE format (60
Disturbance fault cycles each record): 1 to 8 pre-fault cycles + 52 to
Detection of the loss of one phase CT
recording (DFR) 59 postfault cycles.
Function enable: No/Yes
Time delay: 0.020 to 300.000 s (step 0.001 s) 50 records in data and COMTRADE format (30
cycles each record): 1 to 8 pre-fault cycles + 22 to
V1, V2 and VP Tap: 0.08 to 2.00 xUn (step 29 postfault cycles.
0.001xUn)
Function 60VTS
I1, I2 and 3I0 Tap: 0.010 to 20.000 xIn (step 100 records in data and COMTRADE format (15
0.001xIn) cycles each record): 1 to 8 pre-fault cycles + 7 to 14
Timing accuracy: ± 30 ms or ± 0.5% (greater of postfault cycles.)
both)
COMTRADE IEEE C37.111-1991
Function enable: No/Yes
Up to 100 fault reports (data format) with maximum
Time delay: 0.020 to 1.000 s (step 0.001 s) 29 events each one
Function 50BF
Open breaker activation and reset threshold: 0.8% Demand of power with the following characteristics:
In
- Number of records: 2160
Available through configurable inputs thanks to the Load Data Profiling
Function 49T (LDP) - Recording mode circular
programmable logic
- Sampling rate (interval): configurable through
It allows to latch (lock out) the contact trip due to communications (1-60 min)
Function 86
programmable logic (PGC: RSFF or SRFF).
11 configurable inputs
Available through configurable inputs and outputs
Function 68
thanks to the programmable logic (PGC). The voltage of the inputs is the same as the auxiliary
power supply
OR, OR_1PULSE, OR_PULSES, OR_BLINKING,
OR_TIMER UP, OR_TIMER DOWN Inputs Burden: 24 Vdc: <20 mW
NOR, NOR_1PULSE, NOR_PULSES, NOR_ 230 Vdc: <200 mW
BLINKING, NOR_TIMER UP, NOR_TIMER DOWN
24 Vac: <50 mW
AND, AND_1PULSE, AND_PULSES, AND_
BLINKING, AND_TIMER UP, AND_TIMER DOWN 230 Vac: < 500 mW

NAND, NAND_1PULSE, NAND_PULSES, NAND_ 5 configurable outputs

BLINKING, NAND_TIMER UP, NAND_TIMER DOWN Output 1: NO-NC; the rest of the outputs: NO.
Outputs
Programmable logic XOR, OR_1PULSE, XOR_PULSES, XOR_BLINKING, 250 V AC – 8 A; 30 V DC – 8 A
control (PGC) XOR_TIMER UP, XOR_TIMER DOWN
Contact current short duration: 30A – 200ms
SRFF, SRFF_1PULSE, SRFF_PULSES, SRFF_
BLINKING, SRFF_TIMER UP, SRFF_TIMER DOWN, Frequency 50/60Hz
SRFF_NON VOLATIL
Burden of current inputs:
RSFF, RSFF_1PULSE, RSFF_PULSES, RSFF_
BLINKING, RSFF_TIMER UP, RSFF_TIMER DOWN,
RSFF_NON VOLATIL <0.015 VA (1 A) & <0.375 VA (5 A)
R_EDGE, R_EDGE_1PULSE
F_EDGE, F_EDGE_1PULSE Burden of voltage inputs:

4 settings groups
Settings tables < 70 mVA
Selectable by input, communications, user
commands or general setting.
Energizing Burden of power supply unit:
SER 3072 events Quantities

24-230 Vdc/Vac: < 20 VA

Burden for binary inputs:

24 Vdc: <20 mW
230 Vdc: <200 mW
24 Vac: <50 mW
230 Vac: < 500 mW

88
Technical parameters SIL-C

Phase currents (IA, IB, IC), neutral (IN, 3I0), positive 24-230 Vac/dc (24-220 Vdc (±20%) / 100-230 Vac
sequence (I1) and negative sequence (I2) I2/I1 Power supply (±15%))
Maximum current (Imax), thermal Image (TI), Second
harmonic (IA2H, IB2H IC2H), Current Total Harmonic Burden: 24-230 Vdc/Vac: < 20 VA
Distortion (THD-A, THD-B and THD-C). Operating temperature: -40 to 70ºC
Current Fundamental values (DFT) Environmental
Storage temperature: -40 to 80ºC
measurements conditions
Sampling: 32 samples/cycle Relative humidity: 95%
2% precision in a band covering ±20% of nominal Metallic box
current and ±4% in the rest of the range
Panel mounted
Current measurement range: From 0.01 to 30 times
the nominal current Mechanical Vertical assembly: HxWxD: 198x107x145.01 (mm)
Phase voltage (VA, VB, VC), Line Voltage (VL)*, characteristics Horizontal assembly: HxWxD: 107x198x145.01 (mm)
phase-phase voltage (UAB, UBC, UCA), neutral
voltage (VR, 3V0), positive sequence (V1) and IP-54
negative sequence (V2), Maximum voltage (VMAX) The required screws to fix the relay should be M4
and V/f.
(*) Optional depending on model
Fundamental values (DFT)
NOTE: ANSI 67, ANSI 67G and ANSI 67N can be converted into ANSI 51,
Sampling: 32 samples/cycle ANSI51G and ANSI 51N respectively by setting the “Directionality” parameter
to NO.
Voltage Measured voltage: 1% precision in a band covering
measurements ±20% of nominal voltage and 4% in the rest of the
range (ambient temperature)
Calculated voltage: 2% precision in a band covering
±20% of nominal voltage and 4% in the rest of the
range (ambient temperature)
- With VTs: 3-250 V measured voltage (6-250 V
calculated voltage)
- Direct connection: From 12 to 1000 V
Current Angles: IA, IB, IC, IN and 3I0.

Voltage Angles: VA, VB, VC, VR, VL*, 3V0, UAB,

UBC and UCA.
Angle measurements
Power factor: Cos PHI-A, Cos-PHI-B and Total
Cos-PHI-C
Accuracy: ±2º
Total and per phase active power
Total and per phase reactive power
Power
measurements Total and per phase apparent power
2% accuracy in rated values with power factor
between 1 and 0.7 (phase shift from 0 to ±45º).

Energy Positive and negative active energy

measurement Positive and negative reactive energy
Busbar Frequency, Line Frequency, df/dt

Frequency Minimum voltage: 20V P-N (35 P-P)

measurements Accuracy: ±0.005 Hz
Frequency measurement range: From 45 to 65 Hz
Local port (micro-USB): Modbus RTU
Remote port RS485: Modbus RTU, DNP3.0 and
IEC60870-5-103 (selectable by general settings)
Communications
Remote port RJ45 (10/100 Base-Tx): DNP3.0 TCP/
IP, Modbus TCP/IP or IEC60870-5-104 (selectable
by general settings) + SNTP Protocol + Web Server
+ IRIG-B (*)

89
Dimensions and cutout SIL-C

Horizontal assembly

CUT-OUT
PATTERN

90
Dimensions and cutout SIL-C

Vertical assembly

CUT-OUT
PATTERN

91
 A
Connections diagram SIL-C

Phase-phase + residual voltage, 3 current transformers

C B

A
BUS B
C

A1 A2 A3 A4 A5 A6 A7 A8
A B C N
MEASUREMENT

INPUTS
COMMON

VOLTAGE
INPUTS

B3
B4
COMMON

B5
B6
B7
B8 SIL-C
B9 Protection Relay
B10

52 B11
B12
OUTPUTS

LINE
SAFETY
GND GROUND
AC/DC
POWER

B1 Power Supply
AUX.

COM B2

3 VTs CONFIGURATION (PHASE-PHASE) + RESIDUAL VOLTAGE

3 STANDARD CURRENT TRANSFORMERS

(*) Example of connections diagram

92
 A
Connections diagram SIL-C

3 VTs (Phase-neutral) + residual voltage + 1 VT for synchonism , 4 current transformers

C B

A
BUS B
C

A1 A2 A3 A4 A5 A6 A7 A8
A B C N
MEASUREMENT

INPUTS
COMMON

VOLTAGE
INPUTS

B3
B4
COMMON

B5
B6
B7
B8 SIL-C
B9 Protection Relay
52 B10
B11
B12
OUTPUTS

LINE
SAFETY
GND GROUND
AC/DC
POWER

B1 Power Supply
AUX.

COM B2

3 VTs CONFIGURATION (PHASE-NEUTRAL) + RESIDUAL VOLTAGE

(*) Example of connections diagram + 1 VT FOR SYNCHRONISM
4 STANDARD CURRENT TRANSFORMERS

93
Selection & Ordering data SIL-C

SIL-C
Feeder & Generator Protection Relay
PHASE CURRENT MEASUREMENT
0 1 A or 5 A
NEUTRAL CURRENT MEASUREMENT
0 1 A or 5 A
VOLTAGE MEASUREMENT
0 Up to 1000 V (direct connection) or 250 V (with VTs)
POWER SUPPLY
C 24-230 Vac/dc
ADDITIONAL FUNCTIONS
0 -
1 +25 + 27-L + 59-L
COMMUNICATIONS
A A: USB (Modbus RTU) + RS485: (Modbus RTU, IEC60870-5-103 or DNP3.0
Serial)
B B: USB (Modbus RTU) + RS485 (Modbus RTU, IEC60870-5-103 or DNP3.0
Serial) + RJ45 (Modbus TCP or DNP3.0 TCP or IEC60870-5-104)) + Web
Server + SNTP Protocol + IRIG-B
INPUTS AND OUTPUTS
1 11 Inputs + 5 Outputs
MECHANICAL ASSEMBLY
C Vertical Assembly
D Horizontal Assembly
E Vertical Assembly with anticorrosive treatment
F Horizontal Assembly with anticorrosive treatment
LANGUAGE
A English, Spanish, German and French
E English, Spanish, Turkish and Russian
F English, Spanish, German and Portuguese
ADAPTATION
B (2) 50 + SOTF + 50G + 50N + (4) 67/51 + (2) 67G/51G + (2) 67N/51N + 67GI
+ 67NI + 64REF + 46 + 46BC + 49 + 49T + 37 + (2) 27+ 27V1 + (2) 59 + (2)
59N/G + 47 + (4) 32 + (4) 81U/O + (4) 81R + 78 + (2) 24 + 79 + 74TCS +
60CTS + 60VTS + 50BF + SHB + CLP + 52 + 86 + HLT

Example of ordering code:

0 0 0 C 0 A 1 C A B SIL C 0 0 0 C 0 A 1 C A B
SIL-C

(*) ANSI 67, ANSI 67G and ANSI 67N can be converted into ANSI 51, ANSI 51G and ANSI 51N respectively by setting the “Directionality” parameter
to NO.

94
95