Lab - Trace a Route
Objectives
● Determine network connectivity to a destination host
● Trace a route to a remote server using tracert
Background / Scenario
Data travels from a source end device to a destination device. Route tracing software lists the path traversed
by this data.
This route tracing software is typically executed at the command line as:
tracert <destination network name or end device address>
(Microsoft Windows systems)
or
traceroute <destination network name or end device address>
(UNIX, Linux systems, and Cisco devices, such as switches and routers)
Both tracert and traceroute determine the route taken by packets across an IP network.
The tracert (or traceroute) tool is often used for network troubleshooting. By showing a list of routers
traversed, the user can identify the path taken to reach a particular destination on the network or across
internetworks. Each router represents a point where one network connects to another network and through
which the data packet was forwarded. The number of routers traversed is known as the number of hops the
data traveled from source to destination.
Command-line based route tracing tools are usually embedded with the operating system of the end device.
This activity should be performed on a computer that has Internet access and access to a command line.
Required Resources
● PC with internet access
Instructions
Part 1: Determine Network Connectivity to a Destination Host.
To trace the route to a distant network, the PC must have a working connection to the internet. Use the ping
command to test whether a host is reachable. Packets of information are sent to the remote host with
instructions to reply. The PC measures whether each packet receives a response, and how long it takes for
those packets to cross the network.
a. Navigate to the Command Prompt, enter ping [Link] to determine if it is reachable.
b. Now ping one of the Regional Internet Registry (RIR) websites located in different parts of the world to
determine if it is reachable:
Africa: [Link]
Australia: [Link]
South America: [Link]
North America: [Link]
© 2016 - 2020 Cisco and/or its affiliates. All rights reserved. Cisco Public Page 1 of 7 [Link]
Lab - Trace a Route
Note: At the time of writing, the European RIR [Link] does not reply to ICMP echo requests.
The website you selected will be used in next part for use with the tracert command.
Part 2: Trace a Route to a Remote Server Using Tracert.
After you use ping to determine if your chosen websites are reachable, you will use tracert to determine the
path to reach the remote server. Look closely at each network segment that is crossed.
Each hop in the tracert results displays the routes that the packets take when traveling to the final
destination. The PC sends three ICMP echo request packets to the remote host. Each router in the path
decrements the time to live (TTL) value by 1 before passing it onto the next system. To decrement is to count
down. When the decremented TTL value reaches 0, the router sends an ICMP Time Exceeded message
back to the source with its IP address and the current time. When the final destination is reached, an ICMP
echo reply is sent to the source host.
Step 1: Trace a route to [Link].
At the prompt, trace the route to [Link].
C:\Users\User1> tracert [Link]
Tracing route to [Link] [[Link]]
over a maximum of 30 hops:
1 1 ms <1 ms <1 ms [Link]
2 14 ms 7 ms 7 ms [Link]
3 10 ms 8 ms 7 ms [Link]
4 11 ms 11 ms 11 ms [Link]
5 10 ms 9 ms 11 ms [Link]
6 60 ms 49 ms * [Link]
7 43 ms 39 ms 38 ms [Link] [[Link]]
8 33 ms 35 ms 33 ms [Link]
[[Link]]
Trace complete.
In this example, the source host sends three ICMP echo request packets to the first hop ([Link]) with
the TTL value of 1. When the router [Link] receives the echo request packets, it decrements the TTL
value to 0. The router sends an ICMP Time Exceeded message back to the source. This process continues
until the source host sends the last three ICMP echo request packets with TTL values of 8 (hop number 8 in
the output above), which is the final destination. After the ICMP echo request packets arrive at the final
destination, the router responds to the source with ICMP echo replies.
For hops 2 and 3, these IP addresses are private addresses. These routers are the typical setup for point-of-
presence (POP) of ISP. The POP devices connect users to an ISP network.
Step 2: Trace a route to a RIR web site.
a. Now perform a tracert to one of RIR web sites from previous part.
Africa: [Link]
Australia: [Link]
South America: [Link]
North America: [Link]
© 2016 - 2020 Cisco and/or its affiliates. All rights reserved. Cisco Public Page 2 of 7 [Link]
Lab - Trace a Route
b. A web-based whois tool is found at [Link] It can be used to determine the
domains traveled from the source to destination.
Question:
List the domains below from your tracert results using a web-based whois tool, such as
[Link]
© 2016 - 2020 Cisco and/or its affiliates. All rights reserved. Cisco Public Page 3 of 7 [Link]
Lab - Trace a Route
Type your answers here.
© 2016 - 2020 Cisco and/or its affiliates. All rights reserved. Cisco Public Page 4 of 7 [Link]
Lab - Trace a Route
© 2016 - 2020 Cisco and/or its affiliates. All rights reserved. Cisco Public Page 5 of 7 [Link]
Lab - Trace a Route
A
nswer Key
Part 1: Determine Network Connectivity to a Destination Host.
Part 2: Trace a Route to a Remote Server Using Tracert.
© 2016 - 2020 Cisco and/or its affiliates. All rights reserved. Cisco Public Page 6 of 7 [Link]
Lab - Trace a Route
Step 1: Trace a route to [Link].
Step 2: Trace a route to a RIR web site.
List the domains below from your tracert results using a web-based whois tool, such as
[Link]
Answers will vary. Some of the example domains are [Link], [Link], and [Link].
End of document
© 2016 - 2020 Cisco and/or its affiliates. All rights reserved. Cisco Public Page 7 of 7 [Link]
