1710-2690 / 1710-2690 MHz
MHz
6177100
6177100A 6177100G
Double Ultrawideband antenna, dual polarisation, 4 connectors
Wide range of electrical tilt, variable 0°-12° on each antenna XXpol / 65° Az
MET and RET versions, AISG1.1 or 3GPP/AISG2.0 18.0 / 18.0 dBi
Single RET module to control all tilt angles,
fully inserted inside the antenna (field replaceable)
Model number options: 6177100 Manual Electrical Tilts (MET) Antenna
6177100A Remote Electrical Tilts (RET) Antenna (AISG1.1)
6177100G Remote Electrical Tilts (RET) Antenna (3GPP/AISG2.0)
Access Ports Description (Connectors)
The antenna has 4 connectors located at its bottom face. Identification marking is shown next page.
Ultra wide band (1710-2690 MHz) left ports 2 x 7-16 DIN female Long Neck
Ultra wide band (1710-2690 MHz) right ports 2 x 7-16 DIN female Long Neck
Electrical Specifications (general)
The antenna contains two radiating arrays housed in a single mechanical structure.
Isolation between arrays >30 dB
Electrical Specifications of each internal antenna
Frequency Band 1710...1880...2170...2690 MHz
DT 5590 - Ed D- page 1/2 - We reserve the rights to modify our products without prior notice - Several patents pending regarding this product.
Gain 16.9...17.2...17.6...18.0 dBi
Input impedance 50 Ω
VSWR <1.5
Polarisation ±45°
Horizontal Beamwidth (-3 dB) 65°
Vertical Beamwidth (-3 dB) 6°
Electrical Downtilt range 0° to 12° (continuously adjustable)
Isolation between ports >30 dB
Upper Sidelobe Rejection
>18 dB
(20° sector above main beam)
Null fill (first null below main beam) <18 dB typical
Front to back ratio >30 dB
Maximum Power (per port) 160 W
rd
Intermodulation 3 order for 2 x 20 W carriers <-153 dBc
Mechanical
Dimensions (see drawing) Height: 1394 mm Width: 265 mm Depth: 114 mm
Weight 13 kg (excluding mounting accessories)
Shroud Outdoor plastic, Grey RAL7035
Wind Speed Operational: 160 km/h Survival: 200 km/h
Wind load at 160 km/h (EN1991-4-1) Frontal: 524 N Lateral: 196 N Rear: 516 N
Environmental
Operating Temperature Range -40°C to +60ºC
Environmental ETS 300 019
RoHS compliant Yes
Mounting Kit Options (Installation accessories to be ordered separately)
Description Part number Weight
Brackets for pole 48 to 115 mm 0900181/00 3.4 kg
Brackets for pole 70 to 150 mm 0900182/00 3.9 kg
Kit to add mechanical tilt to above brackets 0900396/00 2.3 kg
Wall mounting brackets with azimuth pan 0900183/00 1.6 kg
Wall mounting brackets with mechanical tilt and azimuth pan 0900885/00 3.3 kg
w w w. a m p h e n o l - ja yb e a m . co m
1710-2690 / 1710-2690 MHz
MHz
6177100
6177100A 6177100G
Electrical Downtilt Control
Electrical downtilt is controlled separately for each array. The tilt indicators are covered by a removable transparent cap.
Manual control: A knob at the end of the tilt indicator allows change of the tilt without need for a tool. The marking
pattern (AISG compliant) printed at the bottom of the antenna shows the mapping between tilt control and internal arrays.
To access the knob or to read the downtilt angle, the cap is removed by turning it counter clockwise. It is re-installed by
opposite rotation.
Remote control: The remote control of the electrical tilt is managed by a module (MDCU) totally inserted at the bottom of
the antenna. One single module controls individually the tilt of each array (no need of daisy chain cables between the
actuators). For RET control, the transparent cap must be in place and locked.
The MDCU module does not add any additional length at the bottom of the antenna. The tilt angle indicator stays always
visible and the antenna still has manual tilt control (manual override).
RET module part number (only one needed per antenna) :
MDCU-A0000 For AISG1.1 protocol (one unit included in 6177100A)
MDCU-G0000 For 3GPP/AISG2.0 protocol (one unit included in 6177100G)
An antenna ordered as a RET version is delivered fitted with its factory pre-commissioned MDCU module. It is fully RET ready
and does not need any further action at installation step to become operational.
An antenna delivered as MET can be easily upgraded to RET by simply plugging the MDCU module into the antenna.
Antenna bottom Dimensions (in mm)
DT 5590 - Ed D- page 2/2 - We reserve the rights to modify our products without prior notice - Several patents pending regarding this product.
265 114
Location of the MDCU
for RET control
1394
1127,5
Tilt indicator covered by a transparent cap.
Manual adjustment is accessed by removing the cap.
For RET control, the cap must be in place.
: 1710 - 2690 MHz
: 1710 - 2690 MHz
Installation
Do not install the antenna with the connectors facing upward.
In order to operate RET control, the transparent caps
covering the tilt adjustment indicators must be
engaged and locked. Do not cut them from the
antenna.
Packaging
Carton box
1.61 x 0.365 x 0.23 m (0.135 m3)
23 kg (with pole bracket 0900181/00 in the box)
w w w. a m p h e n o l - ja yb e a m . co m
