Growing Marijuana with Aeroponics

What is Aeroponics?
Aeroponics is a system of growing plants that offers many advantages for
marijuana growing. Simply defined, aeroponics grows plants with their roots suspended
in the air in a grow chamber, with no medium, in a closed-loop system. Nutrient-rich
water is sprayed on the roots of the plants as they dangle in the air. The microbes on the
plant are in an oxygen-rich environment, which allows the microbes time to digest the
nutrients and to make them immediately available to the plant’s circulatory system. Well-
circulating CO2 in the room allows further enhance growth.

Other Hydroponics systems include:
 Ebb and Flow
 Nutrient Film Technique (NFT)
 Wick system
 Continuous flow
 Sea of Green (SOG)
 Screen of Green (SCROG)
Buy LED Grow Lights today
These are trusted partners to delivery Best LED Grow Lights worldwide.

KIND LED Grow Lights – 12 Band Spectrum

Dorm Grow LED – High Times Winner
How does aeroponics work?
  Plants are grown in net pots (like those used in deep water culture), hovering over
a misting system;
 The plant roots are sprayed with a mixture of water and nutrients at high pressure
with on/off intervals;
 The intervals are important in order to gain the great advantages of growing
aeroponically – saving electricity, reducing evaporation and waste, as well as reducing
the likelihood of diseases such as root rot.
 The “off” intervals give the plants a down-time that allows the plant time to take
up the nutrients into its circulatory system.

Aeroponics uses less water and fewer nutrients than other grow systems.
The nutrient-rich water stays in a closed-loop system. A good aeroponic system
will have caps over the net-pots, allowing only the stem through the caps, which reduces
evaporation. This system reduces the risk of the nutrients becoming concentrated too
quickly.

Light is also prevented from penetrating the root zone, making it almost
impossible for algae to thrive.

This relatively disease-free environment allows plants to grow at higher densities

so you can grow more plants per square meter than any other system of growth. Your
grow will outpace soil grows, as well as hydroponic systems such as DWC, bubble-
ponics or nutrient film technique (NFT.)
Aeroponics is not for beginners
A grower should be familiar with how marijuana grows and what a healthy plant
looks like, so problems become apparent early in the process. If you are not technically
inclined, this may not be the system for you. As an aeroponic grower, you need to feel
comfortable replacing misters, pumps and hoses as necessary to keep your system in
good working order.

TAG or FAG and High Pressure or Low Pressure Aeroponic Systems

Many sites host active debates regarding what constitutes a true aeroponic grow
(TAG) versus a faux (or fake) aeroponic grow (FAG.) Another way to distinguish
between the two are high pressure aeroponics (HPS) and low pressure aeroponics
(LPS). Generally speaking, a true aeroponic grow utilizes mist to contact the plant roots
in a grow chamber that is separate from a reservoir. In contrast, a faux aeroponic grow or
low pressure aeroponics (LPA) will utilize a spray mist (usually with a larger droplet
size) as well as another water and nutrient delivery system in a combined grow chamber
or reservoir. LPAs produce droplets that are visible to the naked eye. The other water and
nutrient delivery systems available for FAG include top-feeding drippers. In addition,
there are other systems which allow the plant roots to grow into the nutrient solution at
the bottom of a combined grow chamber and reservoir. A FAG might more accurately be
called a hybrid system. Most DIY aeroponics units are low pressure hybrid systems.
 A true aeroponic grow utilizes a reservoir that is separate from the root
chamber.
Other characteristics of a TAG are a high-pressure pump and mister heads that
produce a fog in the root chamber.

 TAGs are also referred to as high-pressure aeroponic systems (HPS.)

 The fog produced in a TAG/HPS consists of droplets smaller than 50 microns;
  A TAG also uses a cycling timer that can spray the nutrients for 1 to 5 seconds and
then shut off for 3 to 5 minutes. This short burst of nutrient solution on the roots coupled
with the downtime will create a root network of tiny root hairs allowing maximum
colonization of microorganisms, which actually do the work of processing the nutrients
into a form that the plant can digest;
 Minimum droplet size + effective on/off misting timing = more root growth =
more surface area for microbes = amazing plant growth! (More on this in the section on
nutrients later.)

Increased Yields
Extensive root growth allows increased yields and combined with the maximum
root-zone air circulation and minimal risk of disease, aeroponic systems display an
advantage over more traditional indoor hydroponic systems.
 The high oxygen environment is responsible for the massive root growth seen in
aeroponic grows. This has been scientifically proven to increase crop yields by as much
as 10x over the use of soil. Aeroponics allows for a very short veg time, so not only will
your yields increase due to healthier plants, but also because you will be able to grow
more crops per year.
However, the very small margin of error in an aeroponic system creates a
disadvantage.
 For instance, if electrical power stops for any reason, plants will wilt and die rather
quickly because there is no water at their roots;
 You’ll need to keep a close eye on your equipment to make sure your plants don’t
have dry spots where the mist isn’t reaching the roots – especially as the root system
develops;
Aeroponics Step by Step Guide
Step 1 – Which Aeroponics System?
So you’ve decided you want to give aeroponics a try. There are many systems on
the market to get you started. You’re only limited by the amount of space you have
available and your budget.

Check out this DIY LED grow light too.

The lowest end systems are DIY or a retail version of a DIY. These are basically
hybrid systems –they don’t have a separate reservoir. When the roots reach the lower
part of the growing chamber, they will be in the nutrient solution. The nutrient solution is
oxygenated so this shouldn’t cause a problem, unless roots get tangled in your equipment
so it can’t perform. An example of a very inexpensive retail system is the Stealth
Aeroponic system. You really won’t save much by constructing this unit yourself,
although you’d save on shipping.

The Aerogarden is an inexpensive starter system that even includes a CFL light.

Designed to grow herbs with shallow roots (like basil and thyme) on a kitchen
countertop, these units have a devoted, albeit small, following in aeroponic marijuana
growers’ forums. Keep in mind that most users of the Aerogarden
recommend supplemental grow lighting – which could be as simple as some CFL’s on
the side.

Moving toward a more professional grow system, that you’ll want to check out
the General Hydroponics Aeroflo2 system. This hybrid system comes in a variety of sizes
from 18 to 60 plant sites. Nutrient solution is sprayed through the long, narrow root
chamber and is constantly flowing along the bottom. This system is designed to run 24/7.
A good example of a higher-end systemis the Botanicare aerojet 4 x 4 tray. This unit has
misters inside the grow chamber and water flows out the bottom and back to the
reservoir. Unlike the other units described, this unit (as well as other smaller units by
Botanicare) has a separate reservoir. This system also has a timer that has a one minute
on/four minutes off setting, so you won’t have to spend extra money on an external
cycling timer. Again, if you aren’t using a cycling timer, you aren’t going to gain all the
benefits possible from aeroponics.

Construct Your Own DIY System:

You can construct your own DIY hybrid aeroponics system in 2 to 3 hours. The
cost will vary depending on what materials you have on hand and how much you spend
on your timer. This system has 6 plant sites, but you can expand or reduce based on what
you want.

Materials needed:
 25 Gallon Rubbermaid Tote (Rubbermaid brand has plastic that is soft enough to
cut easily. Get a dark color so light can’t penetrate the reservoir;
 4 feet of 3/4″ PVC pipe (get a little extra just in case);
 1 PVC T shaped connector– 1/2″ threaded bottom, 3/4″ open sides (not threaded);
 2 PVC T shaped connectors– 3/4″ open sides;
 4 PVC 90 degree elbows– 3/4″ open sides;
 6″ long 1/2″ nipple pipe (look in the section of the hardware store with sprinkler
fittings);
  Water Pump– about 275 to 300 GPH;
 12 sprinkler heads, ¼ inch, 360 degrees circular spray pattern
 6 net pots, whatever size you want to use (3.75 inches or smaller recommended);
 6 foam inserts, same size as net pots;
 PVC primer and glue;
 Teflon plumbers tape (optional for threaded pipe);
 Cycling timer;
The suggested tools for this job are:
 Drill and drill bit – whatever size you need to drill the holes for the sprinkler
heads;
 Hole saw, jigsaw or small hand saw, or serrated knife (for cutting out holes for the
pots in the lid);
 Saw or special pipe cutters for cutting PVC pipe
Instructions:
 ✓ Line up the net pots on the top of the Rubbermaid Tote lid, three on each side of
the lid (depending on how neat you’d like it to look, you may want to space them
evenly.) Trace the open end of the mesh pots on the lid with a marker;
 ✓ Cut holes for the pots. Use a hole saw to cut the holes, or start by drilling a large
hole into one of the circles you drew, then use a jigsaw or other saw or knife to cut along
the inside of the line you made with a marker (you can always cut a larger hole, but
obviously you can’t make one smaller.) Cut a notch large enough to fit the pump cord
through on one of the holes for the pots. Once you are finished cutting out all holes, clear
away any plastic debris so it doesn’t end up in your system when you finish;
 ✓ Lay out your fittings in the bottom of the container. Put the 90 degree pipe
fittings in each corner. Put a T fitting in the center of each of the two long sides of the
rectangle. The T fitting with the threaded ½ inch connector will go between these two T
fittings, with the threaded end pointing toward the bottom of the container (this will
connect to the pump.)
 ✓ Cut lengths of PVC pipe to connect the fittings. Cut them a little longer than
you think will be necessary – you can always cut them shorter. You’ll have six longer
pieces to connect the T fittings to the corner 90 degree fittings, and two shorter pieces to
connect the two center T fittings with the T fitting that is pointed down toward the bottom
of the container.
 ✓ Drill holes for the sprinkler heads in the six longer PVC pipe sections. Clear all
debris from the pipes.
 ✓ Dry fit the pipes to the connector fittings and cut the PVC pipe to fit if you need
to. Make sure the holes for the sprinkler heads are pointing up toward the top of the
container.
 ✓ Prime the interior of the fittings and the exterior of the PVC pipe sections with
the PVC primer.
 ✓ Apply PVC glue to each of the pipe ends and slip into the fittings. Keep in mind
the angle of the fittings as you are putting things together so that sprinkler head holes are
pointing up, the open ends of the fittings are pointed horizontally and the one center T
fitting with the threaded end pointing downward. Once you have glued the pipes to the
fittings, you have less than a minute to make adjustments before the glue sets.
 ✓ Attach the sprinkler heads to the PVC pipe.

 ✓ Attach the 6 inch, ½ inch diameter nipple to the threaded end of T fitting and to
the pump. Use Teflon tape on the threads if you like.
 ✓ Put water in the bottom of the container and test out the system. Make any
adjustments needed.
 ✓ Run the electrical cord for the pump through the notch in the lid.

 ✓ Fill the container with water, adjust pH and nutrients.

 ✓ Place the net pots in the lid, fill with enough properly rinsed hydroton to support
the plants, and add plants.
 ✓ Plug in the pump to a cycling timer and you are good to go!
Step 2 – Which Grow Lights
When choosing lights, your main concern will be how much heat the lights will
generate. You also don’t want the water in your aeroponics system getting too warm.
Anything that will raise water temperature beyond 75°F (24°C) needs to be neutralized. If
the temperature becomes too hot, you may have to cool your reservoir (or combo
reservoir/grow chamber) with an expensive chiller unit.
 While it’s possible to use high intensity discharge (HID) lights successfully with
an aeroponic system, it is advisable to look to cooler light sources such as CFLs or LEDs.
Using cooler lights simply reduces the likelihood that you’ll have to contend with the
negative effects of higher room temperatures.

Step 3 – Nutrients
 Once you have your lighting system secured, think about nutrients and how you’re
going to feed your plants. Whether you choose to grow with synthetic chemicals or with
organics (or a combination of both), it is important to remember that less is more.
Start by researching what types of nutrients you want to use and what concentrations of
those specific nutrients are recommended by other aeroponic growers using the same
brand of nutrient. A good rule-of-thumb is to start with ¼ of the amount the
manufacturer recommends.
 Keep an eye on your plants to make sure they aren’t displaying signs of toxicity or
deficiency;
 Adjust in small increments rather than larger ones to avoid shock to your plants;

 Remember that nutrients don’t just include the macro nutrients— nitrogen (N),
phosphorus (P) and potassium (K) — because micro nutrients are also essential to the
health of the plants;
 Also important are beneficial microorganisms, or microbes. All healthy root
systems occur because colonies of beneficial microbes have formed on the roots. The
microbes actually process the nutrients into a form that the roots can accept. Keep this in
mind before dosing your water with peroxide or other solutions that might harm these
microbes. You want to have a symbiotic relationship with these tiny organisms. You
don’t want to go to war with them.
Again, adjust all nutrients in small increments to avoid damaging your crop.
Patience in learning how much of your nutrient solution is appropriate for your system
will be rewarded with better harvests and easier grows. You’ll need a properly
calibrated EC (electrical conductivity) or TDS (total dissolved solids) meter to
measure the strength of the nutrients in your reservoir. If you have plant nutrient
recommendations in EC units, you should get an EC meter. If your plant nutrient
recommendations are in ppm (parts-per-million) values, a TDS meter is best.
Keep in mind that the density of your nutrients will increase if water in your system
evaporates. If your system does not have caps over the growing medium, you don’t have
a closed system and water will evaporate quickly. It is also possible that light will
penetrate your water. Covering unused plant sites on your system can help minimize
evaporation and light pollution.

Step 4 – Water
You’ve added nutrients. The next step is water. Keep a few things in mind: the pH
of the water, water temperature and how often you need to change the system’s water.
You may want to start with distilled or filtered water. At a minimum, fill
your reservoir and let it sit without a cover. Chlorine is added to most tap water and you
don’t want chlorine on your grow. Allow the reservoir to sit without a cover for at least
24 hours, preferably more. It is highly advisable to keep an extra reservoir with water that
has been allowed to sit like this in your grow room so that the water is available when
needed.Reservoirs should not be translucent – you need to prevent light from
penetrating the water so that algae doesn’t grow. Algae can clog your system and use
available nutrients that your plants need. It’s easier—and best for your crop— to prevent
algae rather than treat your water to rid an otherwise healthy grow of it.
Read more about marijuana pH here, so I won’t go into depth here – I’ll just mention that
the ideal pH is between 5.5 and 6.5.
You’ll also need to monitor your water temperature – there are a lot of opinions
about what water temp is best, but it is generally agreed that a range of 65 to 75°F (18 to
24°C) is good for your plants. Ideally you’ll keep the temp on the warmer end of the
range for cloning and at the lower end for the grow. If your water temperature is too low,
you should be able to correct with relatively inexpensive aquarium heater.

Water chillers, however, are expensive. If your water temperature is too high
you should consider all the variables that might be contributing to the higher temperature
– your lighting system, your air circulation and air temperature.
 Things to consider
 Is your pump motor working too hard or too much (consider cycling 1 minute on,
4 or 5 minutes off)?
 Do you have a reservoir separate from your grow chamber? Can you put your
reservoir on the floor (where it is coolest) and have your plants elevated?
Treating your grow as holistically as possible will always help troubleshooting when
problems arise. Often one thing OR another isn’t completely wrong—it’s that two, three
or more things are off just a bit.

You are going to need to change your reservoir water to prevent the buildup of
salts and to keep your system healthy. Follow the manufacturer’s instructions, monitor
your nutrients and pH, and change as often as necessary (depending upon your set up and
conditions, this could mean every five days, every week, every ten days – many factors
can affect how often the water needs changing.)
Finally, please consider the environment when you dispose of your old
reservoir water. The best place to dump your water is in your own yard or garden, but
not directly on plants (other than grass.) Storm drains in the street take water directly to
rivers, streams, lakes or the sea and the additional nutrients aren’t good for these bodies
of water or the things that live in them. Additionally, sewer systems can’t filter out all the
additional nutrients so they’ll end up back in a river or the sea anyway.
Step 5 – Air
Maintaining optimal room temperature 70°F (21°C) and keeping the air in your
grow room circulating is essential to a healthy grow. Well-placed exhaust fans (in
addition to any exhaust fans you may have for your lights – depending on the size of your
grow room) to pull fresh air into the room (and send the old air outdoors) will bring
needed CO2 into your space. CO2 is the lifeblood of any plant and well-circulating air
assists in moving it into your grow space. Speaking of exhaust – you will probably also
want to consider how all that expelled air from your grow room is going to smell. Don’t
overlook the importance of oscillating fans to strengthen stems and to help your plants
support themselves. Oscillating fans also help prevent mold and keep pests—like
whitefly—at bay. Keep in mind that moving so much air is going to reduce the humidity
in your grow room and you may need to take steps to correct that. You also may choose
to use added CO2 to enhance your grow, depending on your budget or other factors.
Step 6 – Growing plants!
You’re almost ready to bring plants into your grow room. Always remember that
cleanliness and hygiene are essential to the success of your grow. Start with a tight, clean
space before any equipment goes in, clean up after you add each new component to your
grow room and keep your grow room as clean as you would hope your doctor’s office is.
Any and all effort that you can make to assure cleanliness in your space is a problem that
you are preventing. Prevention is always easier than a cure.
Because aeroponic systems’ designs don’t include support for the canopy—often with a 3
to 6 inch hole in the top of a chamber with roots suspended in the air—you need to think
about supporting your plants before you bring those plants into your grow room.

Sea of Green (SOG)

And Screen of Green (SCROG)
cultivation methods should be considered.
 Once your plant is 18 inches tall, it’s going to need some additional support.
Consider the strain you are growing – generally speaking, indica strains don’t grow as tall
as sativa strains do.
If you want to start your plants from seed, use these instructions for germinating
seed in Rockwool.
If you are interested in growing plants from clones, plant the clones in Rockwool
and once they have rooted, plant your cube into some hydroton in your aeroponic system
(don’t forget to cap your net pot!) You may be able to forego the hydroton all together if
your pots are small enough. Follow instructions for lighting and nutrient use specific to
starting seeds and clones.

For the rest of your grow, follow instructions for lighting and nutrient use (modify
as necessary to apply the general principles for using nutes with aeroponics that were
discussed earlier) for vegging andflowering phases.