8.

Level 3 Repair

8-1. Components Layout

Confidential and proprietary-the contents in this service guide subject to change without prior notice
Distribution, transmission, or infringement of any content or data from this document without Samsung’s written authorization is strictly prohibited.
8. Level 3 Repair

Confidential and proprietary-the contents in this service guide subject to change without prior notice
Distribution, transmission, or infringement of any content or data from this document without Samsung’s written authorization is strictly prohibited.
 Confidential
Z3 EUR REV0.0

BT/WIFI
ANT

SHUB_UART(WLAN)

Dual SIM BT/WIFI

microSD card
(KOR X) SWB-E43
Single SIM

Hall IC 1 (COVER

Hall IC 2 (COVER
OPEN/CLOSE)
DETECTION)
NFC_ANT CAM_SPI
(FROM CAM MCU)

NF C
S3NSE N4XS1
MIC MAIN MIC

WLAN_UART
WLAN_PCIE

HALL_INT2

HALL_INT
BT_UART
BT_PCM
MIC Sub MIC
Switch TDMB
LNA MIC
FC8080 TDMB_SPI 3th MIC

SIM1
RF SW

FM Radio

NFC_HRM_I2C
RTC6213N SPK AMP
FM_GRIP_I2C

SIM2
CS35L40

ESE_SPI
KOR ONLY

AMP_I2S RCV AMP DISPLAY (Z3 : 6.9")

Legacy RF RF IF
SPK_AMP_I2C
CS35L40

MAIN Block COP R_SPI

DDI: S6E3HAB((LSI)
ANT MIPI_4LANE
TOUCH:Y79A(LSI)
TRANSCEIVER TSP_I2C

CP
BTP_SPI

S5510 Marconi BTP Sensor

DISPLAY
(Rx digital, TX Digital) DISP_I2C PMIC - Optic Wide Scanning
S2DOS05 QBT2000
CP_PCIE GEN3
Will Removed
OIS_I2C
CP_SPI (Will be removed) WIDE CAM
SUB6 RF WIDE_AF_I2C WIDE : 108MP 2PD
Power WIDE
RF IF BUCK

S5123
SUB6 Block IPC_GPIOs CAM MIPI_3LANE
CAM_I2C
AF F#1.8
ANT CP_I2S (For Audio)
TELE MIPI_4LANE

AP
CAM_I2C
TELE CAM
TELE : 48MP F#3.5
OIS/AF

SiP UWIDE_CAM MIPI_3LANE

UWIDE_I2C
MAIN_3RD CAM
Ultra WIDE : 12M F#2.2
LPDDR4

EXYNOS9830
TOF MIPI_2LANE ToF CAM Power TOF
TOF_VT_CAM_I2C F1.0 BUCK

(2020)
VTCAM_MIPI_3LANE
FRONT CAM Power FRONT
CP PMIC_I3C 40M AF F# 2.2 BUCK
AF

CAM PMIC
SUB_PMIC_I2C S2MPB02

2ND CAM PMIC

SUB_PMIC2_I2C
UFS_MIPI_2LANE S2MPB03
UFS 3.0 Direct Charging
HAPTIC DRV.
CP PMIC Memory
MOTOR_I2C
MOTOR_INT CS40L25 Block
S2MPM06
I-POP 10x10 4.0t WPC VOUT

AP/PMIC CLK LPDDR5 MFC_AP_I2C WPC RTx

CP CLK MFC_AP_INT P9320 WPC
52MHz CLK
CLK
Buffer Switched Cap
TCXO RFIC CLK
Devider
MP19
Power
5G CLK
MST SW MST COIL
USB
AP/CP UART
WCINOKB
IF PMIC Devider Out Devider Out
BUCK BOOSTER MAX77705 OVP VOUT
MEM_I2C Direct
S2ABB02 REV
Charging
SW charger
USB O TG
UMIC V_BATTERY Direct Charger
Fuel Gauge
PCA9468

PMIC_SPEEDY_SUB

PMIC_SPEEDY
SBU1/2

DP_AUX
CC 1/2

USB 2.0/UART

USB OVP
VBUS
C-TYPE FPF3188
USB3.1SS or DP
SLAVE PMIC AP/CP PMIC
S2MPS22 S2MPS19 AUX SW
SBU_OUT
DG2730DN
   Z3 REV0.1 Confidential/ 對外秘

2G LB GSM_LB
B5/B8/B12/B13/B17/ PRX LB1 DRX_LB1 B5/B8/B12/B13/B17/B18/B19/B20/B26/B28
B18/B19/B20/B26/B28/N28 B20

B28A
GSM LB / B5 / B8 / B12 / B13 / B17
DRX LB1 B18 / B19 / B20 / B26 / B28
N28
B28B
SUB 

LB LFEM
B12+B13
ANT 1
B29

B14

LB LPAMiD HQRX4WJB-361
TRX ANT LMB FRC B71 DRX LB
LB DRX MHB2 B1/B4/B66/B32/B40_6RX
(B5/8/12/13/17/18/19/20/26/28)
HFQTWDVFA-501
B5/B8/B12/B13/B17/
B18/B19/B20/B26/B28
TX2 LB2
B26

B8

TRX ANT HB/N78 DRX FRC
LNA_AUX2 LNA_AUX1
GSM_HB
DRX MHB3
B2/B3/B25 DRX HB MHB2

2G PA
TRX1

TX2 LB1 B40 LNA3

TX2 MHB1 DRX MHB1 B7 4RX

MB DRX MHB6 B7/B38/B40/B41 B7/B40

VRF_VCC_ET_LTE2
S5800
ET DAC1
Legacy

SUB3 MHB2 SUB

MHB LFEM
DRX MHB1 B7 4RX
VRF VCC ET LTE S5800 ANT 5
ET DAC0 B7/B41 LNA1
Legacy PRX UHBLAA2 PRX TR IN N78 4RX

HQRXRHJB-483
B41
DRX MHB4 B3 4RX
PRX B7/38/40/41
DRX MB MHB2
4RX HB
2G LPF B3 LNA2

PRX B1/B3 B25 TX B1/B2/B3/B4/B25/B34/B39 TX1 MHB2 B66 LNA4

DRX N78 4RX B3 TX/ B4 TX / B66 TX

B1 4RX / B4 4RX
B1 TX / B2 RX DRX MHB5
4RX B39
B40 4RX / B66 4RX

B39 RX
MB LNA2 DRX MHB5 B1_4RXD/B4_4RXD/B40_4RXD TRX2
LNAOUT4
B34 RX B1 / B4 / B34 / B66 PRX MHB2
B40 TRX
B1 RX / B4 RX / B66 RX
TRX2
B2 RX
B32/n75/n76
MB LNA1 LNAOUT3
B3 RX / DCS 2G HB / B2 / B3 / B25 / B39 PRX MHB3
B25 RX / PCS B39

B40 RX HB LNA2 LNAOUT1 DRX MHB4 B39/B3_4RXD DRX LB1 2G HB/B2/B3/B25/B39

B40 RX PRX MHB7

OMH LPAMiD
B34

HB LNA1 LNAOUT2
LNA3 B3

SUB 
B41 RX
B41P
B7 / B38 / B41 PRX MHB6
B7 RX

B40/B41 B1

ANT2
AFEM-9130-SG1
SUB2 MHB1
B25

B7/B38/B40/B41 TX1 MHB3 DRX MHB1 B7 4RXD DRX LB1 B1/B4/B34/B66

RFIC DRX ANT
B7 TX B66

LNA4

MHB LFEM
MB LNA3 MHB1
HB LNA AUX4
B3 4RX PRX MHB4
B7

MB AUX1
B34 DRX LB1 B7/B38/B41
HQRX4WJB-452 (ES2)
B7
LNA AUX3

5510
B32 / B1 4RX/B4 4RX/B66 4RX/B40 4RX PRX MHB5
MB AUX2
LNA AUX2
LNA2
HB AUX1
  GPS L1 SUB2
B1/4/66 MIMO2

LNA AUX1
B25/3 MIMO1

HB AUX2 B7 4RX / B38 4RX / B41 4RX PRX MHB1

DRX LB1 B32/B40
 
WIFI1 2.4G
INTERPOSER
B21

LNA1
AUX B32AUX MHB2
AUX B21 TRX1

DRX N78 B34 BPF
B32 DRX
B32/B40 DRX B40 DRX

N41 PRX LFEM ANT N41
B3 4RX

B1 4RX HPF

LNA

B40 4RX

B7 4RX / B38 4RX / B41 4RX
TX1_MHB1 TX1 TR OUT N41
N41_TX_IN PA
B7 4RX TX2_MHB3 TX2 TR OUT N41
B41 BPF

DRX N78 DRX UHBLAA3
SUB
PRX TR IN N78 4RX PRX N78 4RX PRX N78 4RX
ANT 6

DRX LNA_IN N78 DRX N78 4RX DRX UHBLAA2

VRF_VCC_APT_NR

TX1 TR OUT N78 TX1_UHB
N78_TX_IN
TX2 TR OUT N78 TX2_UHB

PRX N78 PRX UHBLAA3

CP
S5123

SUB 
ANT 3

VRF_VCC_APT_NR VRF_VCC_APT_NR VRF_VCC_APT_NR

S5800
Legacy

N41 SRS N41 SRS N41 SRS N41 SRS

TRX ANT N78 TRX ANT N78 TRX ANT N78 TRX ANT N78 TRX ANT N78

 VX_Setup(2018-09-03)_HHP
Created date of PCB data : 2019/12
/24 10:28:41

Model :
Revision :
Manufacture Count :
Charge :
Contact :
Date :
Routing :
L1030

Resin :
V1003

C1039
MIC3000

ANT1003 ANT1000
F1006

ANT1005

ANT1004 ANT1006
V1000

V1011
L1033

BOTHHOLE10000 V1004
L1032

L1028

L1027

C1040
C1038

C1037

L1026
L1037
L1031 V1006
C1041
ANT1007
V1007

V1017

V1005

R3015 C3060
C1044
TP3033

L1042

SOC8000
L1041

C1042

C1081
L1077

C1087

L1007
F1007

C3037
L1039

L1043 L1034 C1043

C3043
C1045

C1095
C3040

C3039
C1005

C1086

L1048 V1010 L3018

C1094

PAM1001
C3010
L3019

C1056
F1003
L1035

F1008
C3042

L1001
C8000

C8008

C8009

C8001

C8007

C8006

C8002

C8010
L8003

V3001

SC104
TH1001
L8001 L1003 L1004
C1084
U1004

ANT3003

R3021 R6004 C3059

C1004 U3003
L1038
C1058

C1076
F1004

L1061
L1062

L3017

R4006 R4007
C1008

L1063
C1026

C1025
L1019

R4005 R4004
L1017

U9007 U9006
C1059 L3013
C1083

C1055 R1001
C1003 L1005
R8000

C3026

R6005
C1088

C1089

C1085
C1091

L1085
C1051
C3058

C1007
C1028
F1001

L1078
R3017

R3014

U1001

U9004

L1023 L1022 C1082 C1079 L1081

C1014
U1007 L1083
L3011
C1090
C1053

L1086
C1019

C1092

C8043
ZD3001

ZD3000

C1080

C1052 C3025
C1078

L1087

L1080

U1003 U1008 L1084

C3057 C1054 C1096
L1079 C1093

V3006

C1015 L1006 C1018 V3007

TP1001

TP1002
L1015

C1016
ZD2003

C1012
F1002

L4049
U1006

L1013
L1010
BOTHHOLE10001

C3070
C1013

C1017

L1008

RFS1000

RFS3000
F3002
L2002

C1677
C3076
L3012

C2016
C1011

L1012

L1066

INT8000
L1057 L1056
ZD2002
C1021

R2003
TH1000

L3005
L1011 C1020 L1065
V1008 V10013
C1029
L3006
ANT1017

R1000
L3007

C3024 C3011 L3001

L1016

L3009
L3004

PAM1000
C3016

C3012 V3004
C3074

L1018
U3002

C3017
C1022

ANT3000
C3009

R3009

U9005
ANT1002

L1020 L1021 C1027 C1024

F3000
L3000

R3010

V3005
V1001

C3018
L3003

L3002
ANT1016

C3013

ZD2000 TP3014

R10000
TP3015

R10002
C3023

TP3026

C10020 TP3027

ZD2004
V10014

TP3021
R3006

R3007

C3006
C3005

L1069

L1067

C10019
C3001

C3004
SC101
R3004

R3005

TP3019
R2000
ANT3006

TP3000 TP3011 TP3012 TP3018

TP3005 TP3001 TP3002

C3002 TP3020
U3001

TP3003 TP3006 TP3004 TP3023

R3000
ANT3005 C2019
C2018

ANT1014
C3000

TP3022
TP3013
C3020

C3008
C2022 TP3024
C2021

C3003 C3055
L3029
L2001

C3050 TP3025
TP3010

C3007 L3027 V3003 C1075

V3002
R3008 TP3016
C3030

C3029

C4001

C4000

R3011

TH3000

C3035

R3012

R3002 TP3008
R3003

ANT1015
TP3009
L8006

SOC8002

L3021
C2015

C3041
R3001

HDC4000
C2014

TP3007
L1076
L3026 C3038
F3004 BOTHHOLE10002
L3024

L3022
ZD2005

TP3017
CON2000 C3027
C3021
C3028

C3045
R7008

C3022

U3005 L8002
L3010 L3008
L3023

L3025
U7005

C8011 R4056

L8009 C6071
R7011
V10000

C6011
C6133

C6006
C6134

C6030
C6013

R6001

R6002

C8032
V10016
ZD8000
C6001 C6000
C8057
C6069

C6012
C8031

C8059

C8028
JTAG4001

C8030 C8029
C6039

L6009
L8008
C6032

TP_PON
C6010

C8027 C6070
L6007
U6002
V10007

V10005

C6034

C6020

L6013
L6005 BOTHHOLE10004
C6015

L6011 C6002 C6005 C5083 C5009

L6001

TP6007

C5026 C5011
C5060

L6000

C5014
TP_POK
C5023
BOTHHOLE10003

C5093
C5104

C5029

C5028

C6132
TP6010
C5022

C6131
C5088
JTAG4003

C5025
INP1200

C5036
C5086

C5037
C5021 C5020
C5019

C5048
C5041
C5085
C5108

C5056

C6060

C6059

C5062
C5084
C5054

C6082
R6003

C5050
TA6000
C5051
C5098

C5047
C5024

C5097 C5089
C6052 C5027
C5052

ZD6003
C5001

C5039

C5038
C5004
C5053
C5006

C5012
C5010

C5099
C9003

C9085
C5094

C5087
C5005

C5002

C5003
C6081

C5007

C9086
C5013

C6053

C5095
C9103

C9080

C5000

C5055
C9011

C9014

C9082
C5049
C9065
L6003

L6004
L6012

L6010

C9013 C9081

C9012 C9064 C9091

C6051
C6048
L9008
C9077

C9070

C6054

L9006
C9095
U9001
C9034

L6008
C9087

C6036 C6035 C6014 C6017

JTAG4002

C9040

C9017

C9018

C9019

L6017

L9001
C6061

C6024

L6006
C6033
C9069

VBUS_IF_5P0_JTAG
C9045

L9007

C6022

INP1100
C6023

L9002
U6000
C6045

C6008
C9058

L6002
GND
L9003
C6047

C9104
L6016
C6044
C6038

C9056 C9025 C9067

C7064

R10005

R10004

C10018

C9036
R10006
C7054

C7033

R4008
ZD7001

C7038
C7059

C9074

C8021 C7017 C7044

R7001

C7026
C7067

C9007

R4009
C9016
L7002 L7001
C7007

C7015

C6043
C7055
R7006

C8020 C7043
C7061

C7062

C8019 C6025
C7023

L6019
JTAG4000

L9005
C6128

L9004 L9000
C9015

C9068

C7011
C9024

C6056
R6009

C6096

C7045
C2011
U7001

ZD6002
C7012

D6001
C7002

C7008
C7016

R4016 C6037 C6031 C6019

C7003

C6046 C6049 C6040

C9076
C9059
C9005

C9004

R4017
U7007
C7036
C6121

C9044
V10012

R4060

R6012

C6063
C6080

C6016

C7037
D6000 C9033
C7013

L6014
L6020
C7056

C7005 OSC6000
C6029

L6015
C7068
R6016

R6029

C9050
V10008

TA9000
R6017

R6015

C7004
L7003

C6127
R7002
C6104
U7002 C9031 C6027
C7019

C9037

C7066
C9020
L7004

C6026
C6004

C9055
TA6002

TA6001

C7027
C7057

C7058

C9030
C9061
C7029

C7065
C9006 L6018
V10009

C6003
C7052

C9054

C9051

C9073

C9029
C7025 C6064
L7000
C7083

C6073

C6021

U7000
C9060

C6028
C9075
C7014

C9002
C7010

C7009

C7035

C7000

C9008

C9046

C9000
C7053
BOTHHOLE10005

C7021

C7034

C6077

C9052
C6066

C6065
C7018

C9066
C6062
ZD7000
C7039

C7041

C7001 V10010
ZD6001

ZD6000

C9047

C9053 C9009
C9001 C9062
C6088

C9057
R7005

R7004

R7000 C6076 C6083

R7003 C6090
C7040 C7042 C7020
C7006
BOTHHOLE10007

BOTHHOLE10006
 Model :
Revision :
Manufacture Count :
Charge :
Contact :
Date :
Routing :
Resin :
U3009

V10003

C1073 C1074
ANT1001
F1009

V1018

C1009 C1010 V1002

ANT3002

C3044

L3020
ANT1008

C8048
V1009

SOC8004
L4050

U3004

L3016 C3036
C3068
ZD3004
U3006

ZD3002
C7060

U7006
C3064
C3056

R3020
ANT3004

C3067
C7063
C3066 R3016
ZD3003
V1013
ANT1012

L3032
C3063
L3030

R3019
ZD3005
ZD3006
V1016 C3065
R4025
R3018
R4026
SIM2000

C1098

C1097

C8049

L3031 C3069

TP10007

SC102
C8051

C8050
L1000

R8002
F1005
C1001 L8016
C8052

C8053
C8042

C8045

C1000
C1035 L1029 C1036
C8058

C8044

L8014
F1000

C8046

R8003
C8054

C8055
R8001

L8013

C8056
ANT3001

C3015
V10002

OSC3000
V3009

CON2002

R7009
C7075

C7074

C7076

R7016

C7047

SC105
C7046 C7082
L7006
U7004
L7007
U7009
C7077
U9003
ANT1013

C7048
C7073

C7071 C7051
L7005

TP3030 TP3029
C3053

R7013

R7012

C3052

U7008
C3049
C7079
C7080

TP3031 TP3032
R4021
C3054

C7049
C7069
C3051
L3028

C7050
L8005

C7072
R4022

C7070

C3062
U3007 TP3028
C7084
U3008

U7003
R7015

L7008
ANT10001

C7081 U7010
C3046 C3048 R7014
C3047

C3061
C7078
V10004

C4010

R4048

R4037

TP9007
TCXO_EN

C1030

R10008

R10003

R10001
U1002

V10006
TP6012

R4027

R4028

R4029
C5061

R4001
C5059

C5057

L1024
R4000

C9039

C9038

C9043

C9042

C8047

C4012
L8015

C5067
C5107
C6041 C6042
TP_NFC_CLK_REQ

TP6018

R6006
C5069
C4008

C4007

C4006
TP4008

TP8000
C1031
C1077
ZD2001

C1034
R2001

C5096
C4011
R4049

L1002
C5075
C5064
L1068

C1071

L1064
C2017 C5030
UCP4000

TP9013

C6068
TP6022

L1052
C5043

C5017 C5042
C1069
C5046

C5045

C1067
C5101

C5092
C1062
C5080
L1014
C1066

TP4007

C5072

C5076

R4018
C5032

U1005 R4019
C1065

TP4006

C5077
TP9017
C6009
C5073

TP4000

TP9018
C5033
R4040

TP9016
C5034
C1064 C1068
TP6009

TP4001

R4039
C5044
R4057

C5066
C5100
R4059

C2020 R2006 L1053 R4031

R4058
C5091
U2001

C5079
TP2020
R2002
U2002
SC106

V4000

R2004
R4030

C5078
TP2019

C5016
R9038

R9037

R4038
R2007 R5000
C2013

R4051 C4009
C6078

C6130

R6028

R6030

C6122

C6123

R6034

R4032
C9097

C9096

TP2018

TP2017
C5090
C6119

TP2014 TP2015

TP2016 C5082 R9036

U6006
R9035

R9034

C5035 C5081
R6020
C2002

C2009 TP2000 R9040 C9099 C5065

C5063
L2000

C9101

C9100

R9039 C9098 C5102

U2000

C5074
R6032

R6033

C5103
C2010 C5018
R9042

R9041
C5031

C6072
C5068

C5058

C5070

C5071

R9001
C6007

TP2004 TP2005 TP2006 TP2008 TP2011 TP2012 TP4004

R4036 R4047 C5105

C2008
TP6001
TP9012

R4035 R4046 C2006 TP6006 R4020 C6055 TP2007 TP2009 TP2010 TP2013 TP4002 TP4005 TP6011

C9010
R9006

R4034 R4045
R9015
R4043

TP4003

C9021
C9094
TH9000
C9079

R9021
R4033 R4044
C2007 R9024
C6074

R9013 R9022
C2012

C8022

C8023
TP6016

C9049

L8000

TP6017
C8024

C8025
C9048

TP9004 TP9008 U9000

C7024
R4014

R4015

C8034

R9020 R9023
C8039

TP9021 TP9006 C9041 L8004 C8018

R9014 R9029
C8040 C8038 C8041 TP_GND4001 TP_GND4000

TP7001 R4012
R6000

TP2003
C2005

TP9011 R4013
TP6000
U9002

VBAT_4000 VBAT_4001
TP9014
R4010
TP2002
C6018

SOC8003
R4011

SOC8001
C8037
C2000

C9072 TP_CC4001
C8016

C8015

TP2001
R4024 R4041 R4042
L8011
R9000

C9022
TP6014 R4023
TP7000

TP_UB0 TP_UB1
C9063 TP_CC4000

C7031
C8026

L8007

TP7002
L8010

C8013

C8014

C8017

C2004 TP9015

TP4009
TP6004

C6079 R9012 C8036

SC103
TP6021 TP_USB_ID

L8012 C8033 C7022 C8035 C8003

UME2000
C8012
TP6013

TP6005 TP6015 R9011 TP6019

TP6008 TP6002 C9027 TP_VBUS

C2001 R6023 R6021

R6008

TP6003
R6018 R6013
C6093

C6089

C6126 TH6000 R6031

TP6020

C6120
C6087 C6086
C6092

C2003
R6024 R6022 L6023 C6110
TP9002

C6100
C6116

C6115

C9035
C6111

C6112
C6095

C6118
C6091

C9023 C6099
U6005 C6102 C6107
TP_DN

U6007
C6108

C6125

R6010
C6124

TP9025
R6011
L6024

U6008
TP_DP

C9028 C6109 R4050

C6094
C6098

C6097

C6106
C6117

V6000 C6129
C6114

L6025 C6105
R9043

C9102

R6026

R6027

TP7004
R9016

R9017

R9018

R9019
C9032

C9026

TP9024
C4003

C4002

C4005

C4004

TP9009
R9010

R9030
R9033

R9032

TP9001 TP9022 TP9023

R9008
L6026
R6035
R6014
C6103
C6101

TP9010
R9025

R9026

R9027

C6113
TP9019 TP9000 R9028 R9007 R9031
R6019
TP9005
R6025

TP_D_P

TP_D_N
 VX_Setup(2019-04-23)_HHP
Created date of PCB data : 2019/12/11 17:14:39

Model :
Revision :
Manufacture Count :
Charge :
Contact :
Date :
Routing :
Resin :
L128

L129

C110
ANT107

SOC10000 SOC100
C158

L148
L144
F101
C157

L150

L149 C161
U105

L203 L204 L145

C170 L151
C156

L143
C133

L132
C159

L142
L153
ANT200

ANT201
U104

L209

L133
L130 C124 C168
C165
U107
C127

C125
ANT108

L155
L210
C223

ANT106

C128
C126

C226
SUS101
C113

L113
C108
C120

C171
U102
U103

L105
AU201
L141

L103
L109

U100 C111 L116

SUS103

SUS102

C114
L104

L108 C106
L123
C112
C104
C107

C135

L114
L101

ANT121

V100

V102
V101

L112
L136
C163

C154

V116
ANT117

L152

ANT102 ANT100 ANT101

 VX_Setup(2019-04-23)_HHP
Created date of PCB data : 2019/12/11 17:14:39

Model :
Revision :
Manufacture Count :
Charge :
Contact :
Date :
Routing :
Resin :

SC100
L121
C117

V110
R211 ZD202 ZD207 ZD205 ZD212 R209 ZD209

R210 ZD201 ZD206 ZD204 ZD213 R208 ZD208

ANT110
ANT120

ZD200

ZD203

V118

V119

C208 L200
U201

C242
L201

C210
U209 V113
ANT109
ANT114

R222
V112

U206
C213
L205

C211
R213 V111
R212

ANT113
C118

L122

V200
C209
C243
ANT119

V115
ANT112

TH201
R220

R221

C241

C240

USB100
TH200
V108

V114 V107
ANT118
 BOTHHOLE18001
C16003

TP16000
C16072
C16002 L16015 L16023 C16001 C16066
TP16002
L16051

L16119
U16018

C16053

R20018

C20031
PAM16000

C16077

L16059

TP16001
C16052
TP16003

C16074
C16054

C16183
L16120

R20015
L16117
C16187

C16188

TP20003
TP16007 TP16008

C16073
L16118

TP20001
C16182
C16139

C16140
AP_XCLKOUT
L16012
PAM16002
C16141

U16012

C16062
C16017 C16051 C16133
C16009
L16054

L16062
L16007
L16021 L18003 L16090

L16058
C16137

C16186
C16185
L16009

C16091

L16060
L16073
C16006

C16058
C16078
L16101

C16056
C16055

C16000
C16164
C16138

C16163
C16142
C16161
C16007

L16107
C16162
C16004

C16022

L16025
L16027

C16016
C16018

L16014

L16016

F16000
C17030 L17002 L16030

L16001
C17027 L17006 L16074 L17018 L16041

TH20000
L16018

R20016

C20029
C16166
L16020

C16167
U16002 SOC18001
L17020 L17004 L16044 L16035
C16165 C16048
L17015 L17008 L16075 L17019

C16020

C16023
C16021
C16019
L17014 C17031 C17020 C16096 C17029 C16043 C16030
L16039

SC18002
C16168 C17004
C16024 C16026
C16042

C17032
C16159

L17022
SC18003

L16010
C16158

C16169
C16174 C16157

C16035
C16037
L16037
L16042
L16045
L17011
L17012
C16045 L16091

L16031
L16036
C16160

L16000
L16040 L16071 L16066
L16106

C17025
L17013

F16001
C16170

L16108
L16105 L16115 C16134

PAM16001
C16088 C16087
L16116
L16032 C16038

C16034
L16034
C16039 L16109 L16064

C16145
U20006

L17024

L17023

R16000
C16149
C16150
L16038 C16047
L16110 L16067

L16103
U20008

C16041
L16043
C16144
C16044

L17017

L17016

U16001
C16154
C16153
U17000
L16029

C16151

C16029
U20010

L16033
F16005

L17010

L17009

L18001
C16155
L17003 L17001

C16015
L16017
C16143

C17017

C17014
L16069

L16004
C16152 L16070

C16147

C16156
C16146 L16068

C17005

L16065
F17000

L16019
C16031
C16148 C17010 C16071
L16063
L16102
L16104
C17012 C17003 C16079

L18000
C16069

F16006
C17009 C17002 C17013

SOC18000
L17000
C17011
C17008 U16015

C16076
C17007
C20019

C20020
C17001
C17018
C17015

TP1007

TP1005
TP1006
TP1004

TP16010

TP16009
C17000 C17006

C16075
L17005 L17007

L16061
R20008

R20020
OSC20000

L16053
C20003
C17016

C17022
R19012
R19011
C16028

C16025
C16027
L16024
C16061

NFC_EN
ESE_SPI_MISO C20025 L16013 C16057
TP17000

C17021
L20000
F17001

U20000
R20010

C20026
ESE_SPI_MOSI

TP20002
ESE_SPI_CS_N
SWDIO
ESE_SPI_CLK
C19003

ZD19003

ZD19001
C19005

ZD19004

NFC_IRQ
R19010

C19025

TA19004
TA19002

C19004
C19006

L19000
C19007
TA19003

C19009
SOC19000 C19020

R19003
U19001

C19023

C18002
R20001
C19013 R20000
R20011
R19004
C19029 C19012

C20027
C20018

TP19000
C20028
C20017
DEBUG_CLK
C19010

C18003
C20023

R19006
NFC_FIRM

L19001

C19022

C19016
R19007
C19021
R20014
C19017
R20009 C20022 C19014
C19015
C19011

eSE_RST

TP20000
C19019

C19018
TA19001
ZD19002 C19008

ESE_INTERNAL
TP19001
TP_DEMOD
TCK
TP19002
BOTHHOLE18000
TA19000
 C20014

C20016
C20015

C20012

C20013
C20010

U20001

R20006
L20002
C20024

L20001
C20021
C20000
C20009

C20008
C19028 C20005

C20007
R20002
C20006 R20003
C18010 R18007

U19003
C20004

TA19005
C18011 R18008

C19002

C19001
C18009 R18006

R19002
ZD19000
C18008 R18005

C19027

C19026
R19000 C18007 R18004
C18006 R18003
R19001 C19000
C18005 R18002
C20046

R20019
C18004 R18001
R18010

C20033
R18009 C20036

INP2100
L16050
U20004

C16060
C20040
C20035
C16059
C20034

U16006

C20032
C16050
L16057
L20004

F16003

U20002
C20050
CON18000 L16056

C20041
SC18001
C16049 C20047
C20042

C20037
C20043
C16176

U16017

R20022
R20023
C16065 C16068
U20005

C20051
C18014

R20024
C16177
C16081 C20039

U17001
U16008
U16016 C16180 R20021

R18013

C20038
C17034
C16175

C16064
C16178

ZD18000
L16113

C20044
R17003

R17002

L20005

C20045
U16010
C16084

C16080
L16089

C16090

L19002
U19002

ZD16000
C19024

U20003
L19003

R20005

R18000
R20004
L20003
R18011
R18014
C20048

C20049
R18012
 GA13000 V13000
TP14004

C13015

SC13000
C13012
V13001

R14013

R14014

L13001
ZD13001
TP13000

TP13004 TP13006 TP13009

TP14000 TP14001
U13001
R15000

C13010
R15002

R15003
R15001

TP13011

SOC13000
CON13001

TP13010

U13000
SOC13002
C13011
R14000
C13000

C13007
R13002

ZD13000

L13000

ZD13002

R14005
C13006

C14033
C14019
ZD14003

TP13003

C14032
C14035

R14006
ZD14005

ZD14004
ZD14000

TP13002 TP13005
C14039
R14012

TP13008
R14004

R14003

C14023
C14026

C13009 TP14008

C14029
C14041 C14038 TP13001

R14007 R14009 R14011

R14008

TP13007
C14025

C14024
C14028

C14027

C14020 C14031 C14030 C14016

TP14007

C14040 R14010
TP14006

ZD14006 C14034 TP14005

L14008

U14001
TP_DISP_DET

V14001

SOC13001 SOC14000
C13016
TH13000

R13003

R13001
C13004

C13017

TP14002 TP14003
 ZD13003 C14021 L14009
C14007
BOTHHOLE14000
TA13000 L14007
L14001

C13001
C13003
C13002
C14009
R14015

ZD14002
ZD14001

C14022
C14008

C14037
C14000 L14006
L14010

C14018
C14014
C14012

L14002
L14003
L14005
C14013

C14015
U14000

R13000

C13005
CON13000

C14006
C13008
C14017

R13004
C14003
C14004

R14002
R14001

L14004
C14005 C14002
C14011 L14000
C14001

C14010
C13013

C13014
INP1500
8. Level 3 Repair

8-3. Flow chart of Troubleshooting.

Oscilloscope Digital Multimeter

Power Supply + driver, ESD Safe Tweezer

8960 & Spectrum Analyzer Soldering iron

Confidential and proprietary-the contents in this service guide subject to change without prior notice
Distribution, transmission, or infringement of any content or data from this document without Samsung’s written authorization is strictly prohibited.
8. Level 3 Repair

8-4-1. Power on

Mobile phone does not power on

YES

Check the Battery NO Charging the battery by TA.

Voltage level. If the voltage has not reached over 3.5V,
Is it more than 3.5V? replace the battery first.
Even if changed the battery, the battery
voltage has not reached, replace the PBA

YES

Power-on the phone and Yes

check the power-on Replace the Front assembly including display.
sound
or motor Vibration.
Sound or Vibration is
ok?

No

When pressing Power NO

key, check if the Power
Replace the POWER KEY FPCB
key FPCB pad on front
is shorted
df

#1 Check the TP7007 is 1.8V

#2 Check the output voltage of U7002 and U7008
crack,open,etc) - R7030 = 3.3V
YES
- TP_UB6000 = 1.8V

※ Each voltage level has ±10% margin

→ Replace the PBA If the voltage level is
abnormal,
NO
Check the signal of
AP_PS_HOLD = 1.8V #4 Check the Clock OSC7000.
Frequency is 38.4MHz
※ Test condition (Oscilloscope setting)
: 20.0ns/div (time division) , 500mV/div (voltage)
YES
 Replace the PBA

check the initial operation (8-4-3)

YES

END

Confidential and proprietary-the contents in this service guide subject to change without prior notice
Distribution, transmission, or infringement of any content or data from this document without Samsung’s written authorization is strictly prohibited.
8. Level 3 Repair

8-4-2. Motor

Motor does not work

Replace the motor to a new one

No
Is there stil the same problem? END

Yes

Are the contact points damaged? Yes Replace ANT170,ANT171 on the USB PBA to new ones
or
(ANT170,ANT171 on the USB PBA) the USB PBA to a new one.
DSE

No

Are the components damaged? Yes Replace L170,L171 on the USB PBA to new ones
or
(L170,L171 on the USB PBA) the USB PBA to a new one.

No

Replace the ASSY SMD(Master+Interposer+Slave) to a new one

END

Confidential and proprietary-the contents in this service guide subject to change without prior notice
Distribution, transmission, or infringement of any content or data from this document without Samsung’s written authorization is strictly prohibited.
8. Level 3 Repair

8-4-3. initial

Initial Failure

Re-download Software

Replace the PBA

YES

END

Confidential and proprietary-the contents in this service guide subject to change without prior notice
Distribution, transmission, or infringement of any content or data from this document without Samsung’s written authorization is strictly prohibited.
8. Level 3 Repair

8-4-4. SIM PART

SIM Card does not work

Yes
Is the SIM card damaged?
Replace the SIM card to a new one.

No

Yes
Is SIM3000 on the master PBA damaged? Replace SIM3000 on the master PBA to a new one.

No

Replace the ASSY SMD(Master+Interposer+Slave) to a new one

END

Confidential and proprietary-the contents in this service guide subject to change without prior notice
Distribution, transmission, or infringement of any content or data from this document without Samsung’s written authorization is strictly prohibited.
8. Level 3 Repair

8-4-5. OTG

OTG does not work

YES
Is USB200 on the USB PBA damaged? Replace USB200 on the USB PBA or the USB PBA to a new one

No

YES
Does it show abnormal voltage at the point below?
Replace the USB PBA or USB CTC FPCB to a new one
C23028 and C23025 on the Right Slave PBA : 5V

``
No

Does it show abnormal voltage at the point below? YES

Replace the ASSY SMD(Master+Interposer+Slave) to a new one
C7133 on the Master PBA : 5V

No

Does it show abnormal voltage at the point below? YES

Replace U7011 on the master PBA to a new one
C7134 and C7005 on the Master PBA : 5V

No

Replace U7003 on the master PBA to a new one

END

Confidential and proprietary-the contents in this service guide subject to change without prior notice
Distribution, transmission, or infringement of any content or data from this document without Samsung’s written authorization is strictly prohibited.
8. Level 3 Repair

8-4-6. Hall IC

Hall Sensor of Certify_Hall does not work

Yes
No
No
Check the voltage
L23000,C23000 =1.8V Replace U7002

Yes
No

Check the voltage No

C10092Magnet
without =1.8V Replace U23000
HALL_INT =1.8V
with Magnet
HALL_INT =0V

Yes
No

END

Hall Sensor does not work

Yes
No
No
Check the voltage
L220,C220 =1.8V Replace U10000

Yes
No

Check
Check the
the voltage
voltage No
C10092 =1.8V
without Magnet Replace U220
HALL_INT2 =1.8V
with Magnet
HALL_INT2 =0V
Yes
No

END

Confidential and proprietary-the contents in this service guide subject to change without prior notice
Distribution, transmission, or infringement of any content or data from this document without Samsung’s written authorization is strictly prohibited.
8. Level 3 Repair

8-4-7. 6Axis sensor

6Axis Sensor does not work

Yes
No
No
Check the voltage
C13011,C7100 =1.8V Replace U7008

Yes
No
No
Check U13001’s package, smd status
(crack, open, short, etc.) Replace U13001

Yes
No
No
Check 6Axis Replace U13001
MOSI, SCK, SCL, SDA pin (If there is still out of order, replace UCP500)
(SPI is OK?)

Yes
No

END

Confidential and proprietary-the contents in this service guide subject to change without prior notice
Distribution, transmission, or infringement of any content or data from this document without Samsung’s written authorization is strictly prohibited.
8. Level 3 Repair

8-4-8. Magnetic sensor

Magnetic Sensor does not work

Yes
No
No
Check the voltage
C4011,C7100 =1.8V Replace U7008

Yes
No
No
Check U4003’s package, smd status
(crack, open, short, etc.) Replace U4003

Yes
No
No
Check R5032, R5036 Replace U4003
(I2C is OK?) (If there is still out of order, replace UCP500)

Yes
No

END

Confidential and proprietary-the contents in this service guide subject to change without prior notice
Distribution, transmission, or infringement of any content or data from this document without Samsung’s written authorization is strictly prohibited.
8. Level 3 Repair

8-4-9. Barometer sensor

Barometer Sensor does not work

Yes
No
No
Check the voltage
C13009,C7100 =1.8V Replace U7008

Yes
No
No
Check U13000’s package, smd status
(crack, open, short, etc.) Replace U13000

Yes
No
No
Check R5047, R5048 Replace U13000
(I2C is OK?) (If there is still problem, replace UCP500)

Yes
No

END

Confidential and proprietary-the contents in this service guide subject to change without prior notice
Distribution, transmission, or infringement of any content or data from this document without Samsung’s written authorization is strictly prohibited.
8. Level 3 Repair

8-4-10. Proximity/Ambient Light sensor

Proximity + Ambient Light Sensor does not work

Yes
No
Check the voltage No
L4003, C4004, R4001, C4010 Replace U7008
=1.8V

Yes
No
No
Check the voltage
L4002,C4006,C9057 =3.4V Replace U9001

Yes
No
No
Check U4001’s package, smd status
Replace U4001
(crack, open, short, etc.)

Yes
No
No
Check R5039, R5042 Replace UCP500
(I2C is OK?)

Yes
No

END

Confidential and proprietary-the contents in this service guide subject to change without prior notice
Distribution, transmission, or infringement of any content or data from this document without Samsung’s written authorization is strictly prohibited.
8. Level 3 Repair

8-4-11. Display

LCD is still off after PWR ON

Yes
No

Check Display Connector on No

MAIN PBA Reconnect the SOC14000

Yes
No
Check No
VDD_DDI_3P0=3.0V (C14030) Resolder or Replace the PMIC (U14000)
VDD_DDI_1P8=1.8V (C14029 )
VDD_DDR_1P6=1.6V(C14041)

Yes
No

No
Check Resolder or Replace the PMIC (U14000)
ELVDD 4P6=4.6V (C14032,C14033)
ELVSS_-4P4 = -1.4 ~ -6.6V (C14020,C14031)
ELAVDD_7P8 = 5.8 ~ 7.9V (C14040)

Yes
No

Replace the UB

Yes
No

END

Confidential and proprietary-the contents in this service guide subject to change without prior notice
Distribution, transmission, or infringement of any content or data from this document without Samsung’s written authorization is strictly prohibited.
8. Level 3 Repair

8-4-12. TSP

Touch Screen does not work

Yes
No

Check TSP Connector on No

MAIN PBA Reconnect the SOC14000

Yes
No
Check No
VDD_TSP_1.8V (C14023) Resolder or Replace U14000
VDD_TSP_3.0V (C14022,C14037)

Yes
No

Replace the UB

Yes
No

END

Confidential and proprietary-the contents in this service guide subject to change without prior notice
Distribution, transmission, or infringement of any content or data from this document without Samsung’s written authorization is strictly prohibited.
8. Level 3 Repair

8-4-13. VT CAMERA

“VT Camera” function does not work

Yes
No

Check the Camera connector No

on Main PBA Reconnect the SOC9003

Yes
No

Check the voltage No

C9103, C9088 : 2.8V
C9104 : 1.05V Resolder or Replace U9014

C9087 : 1.8V

Yes
No
No
Check the VTCAM_MCLK is
Reconnect the PBA
19.2Mhz (C9105)

Yes
No

Replace the camera module

END

Confidential and proprietary-the contents in this service guide subject to change without prior notice
Distribution, transmission, or infringement of any content or data from this document without Samsung’s written authorization is strictly prohibited.
8. Level 3 Repair

8-4-14. Rear CAMERA

“Camera” function does not work

Yes
No

Check the Camera connector No

Reconnect the
on Main PBA
SOC9004,SOC9000,SOC9001,SOC9002

Yes
No

Check the voltage

TOF :
Wide :
C9140 : 2.7V
C9020 : 1.05V
C9139,L9019, C9037 : 1.2V
C9029: 2.8V,
C9136 : 1.8V
C9026 : 1.05V No
C9117 : 3.3V Resolder or Replace U9001, U9002,
C9012,C9019 : 3.3V
U9005,U9007,U9010,U9009,U9011
C9025 : 1.8V
Ultra Wide :
C9094 : 2.95V
Tele :
C9092 : 2.15V
C9017 : 2.9V
C9090 : 1.025V
C9054, C9052, C9015 : 1.8V
C9091 : 1.8V
C9053,C9018 : 1.1V
C9013 : 2.8V

Yes
No No
Check the CAM_MCLK is Replace UCP500-1
19.2Mhz (C9004,C9089,C9142)

Yes
No

Replace the camera module

END

Confidential and proprietary-the contents in this service guide subject to change without prior notice
Distribution, transmission, or infringement of any content or data from this document without Samsung’s written authorization is strictly prohibited.
8. Level 3 Repair

8-4-15. Finger Print

Finger Print Sensor does not work

Yes
No
No
Check the connection of
Display Reconnect or Replace the SOC14000

Yes
No
Check the voltage No
C14021 = 3.7V Check U7002 or L14009 or
C14034 = 1.8V
VPH_PWR(VBAT)

Yes
No
Replace Front A’ssy(UB A’ssy)

END

Confidential and proprietary-the contents in this service guide subject to change without prior notice
Distribution, transmission, or infringement of any content or data from this document without Samsung’s written authorization is strictly prohibited.
8. Level 3 Repair

8-4-16-1. Main MIC

Check main microphone function

In voice call Handset / Loud SPK mode
or voice recorder mode

Check IF USB Board NO

Set the SOC200 connection
Connection (SOC200)

YES

Check the signal of

NO
C250 = 1.8V
Resolder or replace the U7002

YES

Replace the IF USB Board

YES

END

Confidential and proprietary-the contents in this service guide subject to change without prior notice
Distribution, transmission, or infringement of any content or data from this document without Samsung’s written authorization is strictly prohibited.
8. Level 3 Repair

8-4-16-2. Sub(2nd) MIC

nd
Check sub(2 ) microphone function
In camcording mode

YES

Check the signal of

NO
C8009, C8010 = 1.8V
Resolder or replace the U7008

YES

Resolder or replace the MIC8000

YES

END

Confidential and proprietary-the contents in this service guide subject to change without prior notice
Distribution, transmission, or infringement of any content or data from this document without Samsung’s written authorization is strictly prohibited.
8. Level 3 Repair

8-4-16-3. 3rd MIC

Check 3rd microphone function

In camcording mode. (Audio zoom)

YES

Check the signal of

NO
C8012 = 1.8V
Resolder or replace the U7008

YES

rd
Resolder or replace the 3 MIC FPCB

YES

END

Confidential and proprietary-the contents in this service guide subject to change without prior notice
Distribution, transmission, or infringement of any content or data from this document without Samsung’s written authorization is strictly prohibited.
8. Level 3 Repair

8-4-17. Speaker part

Check the speaker function,

Play MP3 with maximum volume level

YES

`
Check IF USB Board
NO
Set the SOC200 connection
Connection ( SOC200)

YES

Check the contact

NO
C-clips(pins) of replace IF USB Board
ANT240, ANT241

YES

Check the signal of

NO
C23018, C23019, C23020,
Resolder or replace the U23003 (SPK amp)
C23016 ,C23017 = 11V

YES

Check the signals of NO

replace IF USB Board
L240, L242

YES

Replace the SPK module

YES

END

Confidential and proprietary-the contents in this service guide subject to change without prior notice
Distribution, transmission, or infringement of any content or data from this document without Samsung’s written authorization is strictly prohibited.
8. Level 3 Repair

8-4-18. Receiver part

Check the Receiver function,

In voice call Handset mode

Check the contact

NO
C-clips(pins) of
Resolder or replace the ANT8005, ANT8003
ANT8005, ANT8003

YES

Check the signals of

NO
Resolder or replace the U8000 (RCV amp)
C8001, C8002, C8000 =
11V

YES

Check the signals of NO

L8002, L8001 Resolder or replace the L8002, L8001

YES

Replace the RCV module

END

Confidential and proprietary-the contents in this service guide subject to change without prior notice
Distribution, transmission, or infringement of any content or data from this document without Samsung’s written authorization is strictly prohibited.
8. Level 3 Repair

8-4-19. BT/WIFI

BT/WIFI is not working

Yes
No
No
Check BT or WIFI fuction ON Enable BT or WIFI function.

Yes
No
No
Check the Voltage on Check the U7002
C3000 = 1.8V
(Crack, open, damaged, etc)

Yes
No

Check the Voltage on No

C3001,C3009,L3026 = Resolder or change C3001,C3009,L3026
3.7~4.3V(VBAT)

Yes
No
Check the status of No Resolder or change the
ANT2004,ANT2005,ANT2012,
ANT2004,ANT2005,ANT2012,ANT3001,
ANT3001,ANT3003,ANT3004,
ANT3003,ANT3004,ANT3005,ANT3006
ANT3005,ANT3006

Yes
No

Check the Status of No Resolder or Replace of

V2006,V2013,V3003,L3038,C2017, V2006,V2013,V3003,L3038,C2017,C3014
C3014

Yes
No

Resolder or change U3001

Yes
No

END

Confidential and proprietary-the contents in this service guide subject to change without prior notice
Distribution, transmission, or infringement of any content or data from this document without Samsung’s written authorization is strictly prohibited.
8. Level 3 Repair

8-4-20. GPS

GPS is not working

Yes
No
No
Check GPS function ON Enable GPS Function in the setting.

Yes

No 1. Resolder or Replace
Check the Antenna ANT2004, ANT2005
connection 2. Replace REAR

Yes
No
well.Check(crack,open,etc)
V2003,L2020,C2017,L2021,C2018,L2015, No
C2019,L2016,F2001,C2119,L2085,L2076,L2081, Resolder or change the wrong element
C2126,L2077,U2020,L2075,L2078,C2123,L2027, (open, crack, deviation, etc)
C2116,L22004,L22008,F22001,L22005,C22142

Yes
No
well.Check(crack,open,etc)
V2001,L2009,L2005,L2007,C2004,L2008,F2002, No
L2024,L2023,L2086,U2021,L2079,L2127,C2125,L2144, Resolder or change the wrong element
C2121,L22140,L22006,F22000,L22007,C22003 (open, crack, deviation, etc)

Yes
No
No Check OSC7000
Check 38.4MHz Clock at output
of OSC7000 (short, open, crack, etc.)

Yes
No
No Check AP PMIC(U7002)
Check the voltage on
L2075=1.7V (short, open, crack, etc.)

Yes
No
Resolder or change U22001

Yes
No

END

Confidential and proprietary-the contents in this service guide subject to change without prior notice
Distribution, transmission, or infringement of any content or data from this document without Samsung’s written authorization is strictly prohibited.
8. Level 3 Repair

8-4-21. NFC

NFC is not working

Yes
No
No
Check NFC function ON Enable NFC Function

Yes
No
No
Check the NFC FPCB Antenna Replace NFC Antenna

Yes
No
No
Check the Antenna connect Resolder or Replace SOC22000
SOC22000

Yes
No

Check the voltage on No

C22039 = 1.8V Check AP PMIC_C(U7008)
Check reference clock at (short, open, crack, etc.)
C22082

Yes
No

Check the NFC signal Check L22000, L22001, C22069, C22081,

No C22075,C22078,C22074,C22080,C22076
at SOC22000
(Keystring *#6328378# -> C22079,C22077 R22006,R22001
PRBS test -> start) (crack, open, damaged, etc.)

Yes
No

Resolder or Replace U22000

Yes
No

END

Confidential and proprietary-the contents in this service guide subject to change without prior notice
Distribution, transmission, or infringement of any content or data from this document without Samsung’s written authorization is strictly prohibited.
8. Level 3 Repair

8-4-22. MST

MST is not working

Yes
No
No
Check the battery level
Battery >= 5% Charging the Battery

Yes
No
No
Check MST FPCB Antenna Replace MST Antenna

Yes
No
No
Check the Antenna contact
SOC22000 Resolder or Replace SOC22000

Yes
No
No
Check voltage at C22116
Resolder or Replace U24003, U24004
Check signal at ZD22002
(*#0*# -> MST test -> turn on
continous)
Yes
No

END

Confidential and proprietary-the contents in this service guide subject to change without prior notice
Distribution, transmission, or infringement of any content or data from this document without Samsung’s written authorization is strictly prohibited.
8. Level 3 Repair

8-4-23. Charging Part

Wire Charging (Normal/Fast)

TA / USB Insert

Charging Sequence Start NO

Slave PCB C23028 and C23025 = 5V or 9V Reconnect TA or USB or Replace USB PCB or USB CTC

FPCB

YES
NO
Resolder or Replace U7000

NO
Check the voltage Master PCB C7133 = 5V or 9V Replace the ASSY SMD(Master+Interposer+Slave) to

a new one

YES
NO
Resolder or Replace U7000

NO
Check the voltage Master PCB C7134 or C7005 = 5V or 9V Replace U7011 to a new one

YES
NO
Resolder or Replace U7000

NO
Replace U7003 (Normal or 15W) or U7006 (25W) to
Battery is Charging?
a new one

YES
NO
Resolder or Replace U7000

END

Confidential and proprietary-the contents in this service guide subject to change without prior notice
Distribution, transmission, or infringement of any content or data from this document without Samsung’s written authorization is strictly prohibited.
8. Level 3 Repair

8-4-24-1. Charging Part

Wireless Charging (Normal/Fast)

Contact Wireless charger

Check C22116 > 5V

NO Check SOC22000
Replace MFC/MST/NFC combo ANT

YES
NO
Resolder or Replace U7000

Check whether one of these short or not:

NO TA22002, TA22003, TA22004, TA22000, TA22001
Charging Sequence Start , C22116, C22100 (slave)
Check C22100 = 5.5V or 10V
If yes, replace damaged part.

YES
NO
Resolder or Replace U7000

Check again about NO Resolder or Replace

U22003 (Slave)
charging status

YES
NO
Resolder or Replace U7000

END

Confidential and proprietary-the contents in this service guide subject to change without prior notice
Distribution, transmission, or infringement of any content or data from this document without Samsung’s written authorization is strictly prohibited.
8. Level 3 Repair

8-4-24-2. Wireless Power Sharing

Place Phone to Phone(Galaxy Gear or Buds)

Yes

Check whether one of these short or not:

No TA22002, TA22003, TA22004, TA22000, TA22001
Charging Sequence Start C22116, C22100 (slave)
VOUT(C22100) = 4.5V ~ 8V(5V or 7.5V) If yes, replace damaged part.
If not,
Resolder or Replace U7003(master)
Yes

No
Check the VRECT(C22116) =
Resolder or Replace U22003(slave)
4.5V ~ 8V

Yes

No
Check SOC22000
Is the function OK? Replace MFC/MST/NFC combo ANT

Yes

END

Confidential and proprietary-the contents in this service guide subject to change without prior notice
Distribution, transmission, or infringement of any content or data from this document without Samsung’s written authorization is strictly prohibited.
8. Level 3 Repair

8-4-25 GSM 850/900, CDMA BC0/10, WCDMA B5/8, LTE B5/8/12/13/14/17/18/19/

20/26/28/29/71, NR n5/71 RX

NORMAL CONDITION
Catch the channel?

No

Yes
Check C21007 ≤ -65dBm Check the SUB PBA / FRC or ANT

No
Yes
Resolder or change
Check C21004 ≤ -65dBm
L21004, L21007

No

No
Check component
soldering status ok? Resolder or change
U21004 U21004

Yes

Yes
Check if all C21010 and Resolder or change
C21011 ≤ -65dBm C21010, C21011

No

Check the SDR(U22001)

Confidential and proprietary-the contents in this service guide subject to change without prior notice
Distribution, transmission, or infringement of any content or data from this document without Samsung’s written authorization is strictly prohibited.
8. Level 3 Repair

8-4-26. CDMA BC1, GSM 1800/1900, WCDMA B1/2/4, TDSCDMA B34/39, LTE
B1/2/3/4/25/39/66 B7/30/38/40/41 RX

NORMAL CONDITION
Catch the channel?

No

Yes
Check C21007 ≤ -65dBm Check the SUB PBA / FRC or ANT

No
Yes Resolder or change
Check L21011 ≤ -65dBm L21008, C21008, C21009, U21003,
L21015, L21011, L21016

No

No
Check component
soldering status ok? Resolder or change
U21007 U21007

Yes

No

Check C21036 or C21037, Resolder or change

orL21021, or L21022 ≤ -65dBm C21036 or C21037or L21021 or L21022

Yes

Check the SDR(U22001)

Confidential and proprietary-the contents in this service guide subject to change without prior notice
Distribution, transmission, or infringement of any content or data from this document without Samsung’s written authorization is strictly prohibited.
8. Level 3 Repair

8-4-27. CDMA BC0/10, GSM 850/900, WCDMA B5/8, LTE

B5/8/12/13/14/18/19/20/26/28/29/48/71, NR n5/71 DRX

NORMAL CONDITION
Catch the channel?

No

No Resolder or change
Check C2004 ≤ -65dBm ? ANT2001, V2001, L2005,
L2009, L2007

Yes

No
Check C2034 ≤ -65dBm ? Resolder or change
F2002, C2034, L2057

Yes

No
Resolder or change
Check C2006 ≤ -65dBm ? C2006, F2000, L2011

Yes

No
Check component
soldering status ok? Resolder or change
U2001 U2001

Yes

Check the SDR(U22001)

Confidential and proprietary-the contents in this service guide subject to change without prior notice
Distribution, transmission, or infringement of any content or data from this document without Samsung’s written authorization is strictly prohibited.
8. Level 3 Repair

8-4-28. LTE B48 RX

NORMAL CONDITION
Catch the channel?

No

No Check the ANT,

Check C2030 ≤-65dBm V2005, L2031, C2036, L2026,
C2021, RFS2001, L2032, C2030
C2237, RFS2004, L2152, C2236
Yes
No
Resolder or change
Check C2032 ≤-65dBm
C2031, C2032

Yes

No
Resolder or change
Check C2122 ≤-65dBm
C2120, C2115, C2122

Yes

No
Check component
soldering status ok? Resolder or change
U2017 U2017

Yes

Check the SDR(U22001)

Confidential and proprietary-the contents in this service guide subject to change without prior notice
Distribution, transmission, or infringement of any content or data from this document without Samsung’s written authorization is strictly prohibited.
8. Level 3 Repair

8-4-29. NR n41 RX

NORMAL CONDITION
Catch the channel?

No

No
Check the ANT, V2003, L2020, C2017,
Check C2019 ≤-65dBm
RFS2000, L2021, C2018, C2019

Yes
No
Resolder or change
Check C2052 ≤-65dBm No
F2001, C2052

Yes

No
Resolder or change
Check C2049 ≤-65dBm
U2009, C2051, U2008, C2049

Yes

No
Resolder or change
Check C2095 ≤-65dBm
U2006, C2094, L2066, L2067, C2095

Yes

No
Resolder or change
Check C2022 ≤-65dBm
C2208, F2005, C2022

Yes

No
Check component
soldering status ok? Resolder or change
U21002 U21002

Yes

Check the SDR(U22001)

Confidential and proprietary-the contents in this service guide subject to change without prior notice
Distribution, transmission, or infringement of any content or data from this document without Samsung’s written authorization is strictly prohibited.
8. Level 3 Repair

8-4-30. CDMA BC1, WCDMA B1/2/4, TDSCDMA B34/39, LTE B1/2/3/4/25/66

B7/30/38/40/41 TX

NORMAL CONDITION
Catch the channel?

Check C21027 or C21028

Check the SDR(U22001)
> -22dBm
No

Yes

Check component
Resolder or change
soldering status ok?
U21007
U21007 No

Yes

Resolder or change
Check C21008 > -22dBm U21003, L21015, L21011, L21016
No

Yes

Resolder or change
Check C21007 > -22dBm L21007, C21007, L21008, C21008,
C21009
No

Check the SUB PBA / FRC or ANT

Confidential and proprietary-the contents in this service guide subject to change without prior notice
Distribution, transmission, or infringement of any content or data from this document without Samsung’s written authorization is strictly prohibited.
8. Level 3 Repair

8-4-31. GSM 1800/1900 TX

NORMAL CONDITION
Catch the channel?

No

Check the
Check C21080 > -22dBm SDR(U22001),L21069,C21080,
C21088
No

Yes

Check component
Resolder or change
soldering status ok?
U21015
U21015

No
Yes

Resolder or change
Check C21081 > -22dBm
C21081,L21071,L21073
No

Yes

Check component
Resolder or change
soldering status ok?
U21007
U21007 No

Yes

Resolder or change
Check C21008 > -22dBm C21008,L21011,L21015,L21016,U21
No 003,C21009

Yes

Resolder or change
Check C21007 > -22dBm
L21007,C21007,L21008,
No

Check the SDR(U22001)

Confidential and proprietary-the contents in this service guide subject to change without prior notice
Distribution, transmission, or infringement of any content or data from this document without Samsung’s written authorization is strictly prohibited.
8. Level 3 Repair

8-4-32. GSM 850/900 TX

NORMAL CONDITION
Catch the channel?

No

Check the
Check L21067 > -22dBm SDR(U22001),L21067,L21068

No

Yes

Check component
Resolder or change
soldering status ok?
U21015
U21015

No
Yes

Resolder or change
Check C21084 > -22dBm
C21084,L21070,L21072
No

Yes

Check component
Resolder or change
soldering status ok?
U21007
U21007 No

Yes

Resolder or change
Check C21008 > -22dBm C21008,L21077,C21004,L21004,U21
No 003,,C21009

Yes

Resolder or change
Check C21007 > -22dBm
L21007,C21007,L21008,
No

Check the SDR(U22001)

Confidential and proprietary-the contents in this service guide subject to change without prior notice
Distribution, transmission, or infringement of any content or data from this document without Samsung’s written authorization is strictly prohibited.
8. Level 3 Repair

8-4-33. CDMA BC0/10, WCDMA B5/8, LTE B5/8/12/13/14/18/19/

20/26/28/29/71, NR n5/71 TX

NORMAL CONDITION
Catch the channel?

No

Yes
Check if all C21014 and
Check the SDR(U22001)
C21023 ≤ 0dBm

No
Yes Resolder or change
Check C21006 ≤ 0dBm C21015, F21002, U21005,
C21024,C21006

No

Check component No
Resolder or change
soldering status ok? U21004
U21004

Yes
Yes
Resolder or change
Check C21004 ≤ 23dBm
C21004, L21077

No

Yes
Check C12007 ≤ 23dBm Resolder or change
C21007, C21008, U21003

No

Yes
Check C12007 ≤ 23dBm Resolder or change
C21007, C21008, U21003

No

Check the ANT

Confidential and proprietary-the contents in this service guide subject to change without prior notice
Distribution, transmission, or infringement of any content or data from this document without Samsung’s written authorization is strictly prohibited.
8. Level 3 Repair

8-4-34. B48 TX

NORMAL CONDITION
Catch the channel?

No

No
Check C2111 > -22dBm Check the SDR(U22001)

Yes

No
Check L2070 > -22dBm Resolder or change
C2111, L2070

Yes

No
Check component Resolder or change
soldering status ok? U2017
U2017

Yes
No
Resolder or change
Check C2120 > -22dBm C2122, C2115, C2120

Yes

No Resolder or change
Check C2036 > -22dBm o C2032, C2031, C2030, L2032,
RFS2001, C2021, L2026, C2036

Yes

No
Check component Resolder or change
soldering status ok? L2031, V2005
L2031, V2005

Yes

Check the ANT

Confidential and proprietary-the contents in this service guide subject to change without prior notice
Distribution, transmission, or infringement of any content or data from this document without Samsung’s written authorization is strictly prohibited.
8. Level 3 Repair

8-4-35. NR n41 TX

NORMAL CONDITION
Catch the channel?

No

Check the SDR(U22001),

Check L21078 > -22dBm C21119, L21078

No

Yes

Check component Resolder or change

soldering status ok? U21002
U21002
No

Yes

Resolder or change
Check C2094 > -22dBm C2022, F2005, C2208, C2095,
L2067, L2066, C2094
No

Yes

Check C2052 > -22dBm Resolder or change

No U2006, C2049, U2008, C2051,
U2009, C2052
Yes

Resolder or change
Check C2017 > -22dBm F2001, C2019, C2018, RFS2000,
No C2017

Yes

Check component
Resolder or change
soldering status ok?
L2020, V2003
L2020, V2003
No

Yes

Check the ANT

Confidential and proprietary-the contents in this service guide subject to change without prior notice
Distribution, transmission, or infringement of any content or data from this document without Samsung’s written authorization is strictly prohibited.
8. Level 3 Repair

8-4-36. Dex Station

Dex Station does not work

No
Does the phone show the charging UI? Replace U7003 on the master PBA to a new one.

YES

No
Does the phone show the DEX UI?
Replace U7009 on the master PBA to a new one.

YES

YES
Is USB100 on the USB PBA damaged? Replace the USB PBA to a new one.

No

Replace the ASSY SMD(Master+Interposer+Slave) to a new one

END

Confidential and proprietary-the contents in this service guide subject to change without prior notice
Distribution, transmission, or infringement of any content or data from this document without Samsung’s written authorization is strictly prohibited.
8. Level 3 Repair

8-4-37. mmWave Trouble shooting

Daseul Calibration fail

No Check SOC10000.
Top Module Check OK?
If it is OK, replace FPCB or the module for the top.

YES

No
Left Module Check OK?
Check SOC13002.

If it is OK, replace FPCB or the module for the left.

YES

No Check SOC22001.
Right Module Check OK?
If it is OK, replace FRC or the module for the right.

YES

No
Phasor 0/1/2 Spec fail? Replace PBA

YES

Replace FPCB or the module like below.

Phasor 0: Ones for the top

Phasor 1: Ones for the left

Phasor 2: Ones for the right

END

Confidential and proprietary-the contents in this service guide subject to change without prior notice
Distribution, transmission, or infringement of any content or data from this document without Samsung’s written authorization is strictly prohibited.