SPECIFICATIONS] GENERAL Power source Power consumption. AC 110/220/240V,, 50/60Hz .270W Semiconductors.........1-1C (Integrated circuit), 47-Transis- tors, 24-Diodes, 1-LED Dimensions. .442(W) x 144(H) x 380(D) mm Weight 14.5 kg MAIN AMPLIFIER Circuit... Two-step differential amplifier, pure complementary system, OCL (Output Condenser-Less) Continuous power output 2x SOW/4-ohms.....Both channels drive, at 1kHz 2x 35W/8-ohms......Both channels drive, at IkHz Total harmonic distortion, 0.02% at 25W Intermodulation distortion 0.05% at 25W Damping factor Power band width More than 25 (at IkHz , 4-ohms) THz ~ 70kHz at 0.3% distortion, 25W Frequency tesponse.....1SHz ~ 90kHz (+1.54B) Input sensitivity and input impedance.........800mV/S0k ohms PRE AMPLIFIER Circuit... Three-step direct coupled equalizer circuit whose first step serves as differential amplifier. Type “NF” tone control circuit. BF opTonica | SERVICE MANUAL MODEL SM-3000H “In the interests of usersafety the set should to its original condition and only parts identi specified be used.” restored to those i Input sensitivity and input impedance PHONO 1. ..2.5mV, SmV/47k ohms PHONO 2 2.5mV/22k ohms, 47k ohms, 100k ohms AUX I and 2...... 1SOmV/47k ohms TAPE PLAYBACK 1 and 2 150mV/47k ohms TAPE PLAYBACK 1 and 2 (DIN socket) 1 and 2.....150mV/47k ohms Output level and loaded impedance REC 1 and 2....... 150mV/47k ohms REC 1 and 2 (DIN socket) Max. allowable input for PHONO 30mV/80k ohms 300mV(RMS, 1kHz) 850mV(P-P, IkHz) Deflection of “RIAA” curve for equalizer circuit from standard SRIAA™ CUIVE sommes 40.34B Frequency response... SHz ~ 90kHz (TUNER, AUX, TAPE PLAYBACK) Tone control Bass +104B at 100Hz, turnover... 600Hz +#104B at 60Hz, turnover..... 300Hz Treble... +294B at 10kFz, turnover...... 1 SkH2 #94B at 20kHiz, turnover...... 3kHz Filter, Low cut 30Hz, 12dB/oct High cut, THz, 6dBjoct SHARP CORPORATION osaka, JAPANCABINET TOP REMOVAL (Refer to Figure 1) @ Remove 8 screws attached to washer located at side decoration panel of cabinet. Remove 2 screws attached to washer of CABINET TOP. Gently lift up the CABINET TOP. OPERATION PLATE REMOVAL (Refer to Figure 1) @ Remove all knobs provided at the OPERATION PLATE. © Remove 6 screws located at OPERATION PLATE. 2) Remove 12 screw of CABINET BOTTOM Caution: These (@) mark of two screws are 49 x 8 mm. Another ten screws are_ 36x 6 mm. Figure 2 PREPARATION FOR USE: MAINS VOLTAGE SELECTION (Refer to Figure 3) Be sure to check the pre-set voltage selector before operating the set. If the voltage is different from your local voltage, change it in the following manner: 1, Loosen a screw and slide the cover as illustrated in Figure 3. 2. Put a fuse in the fuse holder which has an indication of your local voltage. Note: In case the local voltage is 110V, two pieces of fuses should be used. 3. Replace the cover in its original position. CIRCUIT DESCRIPTION EQUALIZER AMP! Figure 3 The equalizer circuit is driven by three kinds of power sources. The transistor at the final stage is given a high voltage of 70V to assure the amplifier of satisfactory dynamic range. ‘The equalizer circuit consists of high-precision parts (resistor, capacitor etc.) so that RIAA diviation is limited to the maximum (within £0.34B) and the impedance of RIAA elements is kept high to suppress possible distortion at the high frequency band.CIRCUIT DESCRIPTION Passing through C301 and R303, the output of cartridge enters the differential amplifier consisting of Q303 and Q30S (Low Noise Transistor). Q301 and D301 is constant-current circuit and serves as load for Q303. ‘The output of Q303 enters Q307 (Emitter Follower Circuit) via R317. (C309 and C311 located at the base circuit of Q307 is high frequency oscillation proventive circuit). The output of Q307 is amplified by Q309 (Class “A” Amplifier). The gain of equalizer circuit mostly depends upon Q309. ‘Since RIAA characteristic is determined by C315, R335, R337 and C319 (Negative Feedback Circuit), these parts should be qualified cones. Notes: R333... It serves to make easier the discharge of C317 and also to restrict shock noise caused when the function switch is operated. €303.... It serves to prevent SW broardcasts etc. from mixing| in the unit (this is caused due to high gain of equalizer circuit). TONE AMPLIFIER The tone circuit makes use of the high gain of IC (Integrated Circuit) which incorporates differential one-stage ditectcoupled three-stage circuit, in order to lower the distortion factor. There are two kinds of power source to drive the tone circuit and the potential of input/output part is kept zero. ‘The capacitor used for the input/output part is low leak type to reduce residual noise, Figure 4 Trl tf if e CIRCUIT DESCRIPTION After being controlled by the volume control (VR302), the signal enters the terminal 6 of IC401 via C40S. The signal amplified by IC401 comes out of the terminal 2 and enters the filter circuit via 439, The negative feedback circuit consists of the parts of tone circuit Tone control of low or high frequency band is made by varying NF amount by the variable resistor (VR303, VR304). Frequency turnover is made by the switches (SW401; low frequency ‘band, SW402; high frequency band) to vary the capacitance of capacitor. The variable/defeat circuit consists of the switch (SW403) that switches over the tone control NF circuit and NF circuit having a flat frequency characteristic FILTER CIRCUIT There are two type of filter circuit, one; 7kHz, -6 dB/oct and another; 30 Hz, -12 dB/oct. CIRCUIT DESCRIPTION The high cut filter consists of R461 and C450, and the cutoff frequency is 7kHz and the attenuation, 6 dBjoct. The low cut filter is a filter of NF (including C443 and R449) type making use of the emitter follower, and the cutoff frequency is 30 Hz and the attenuation 12 dB/oct.MAIN AMPLIFIER ‘The main amplifier consists of all-stage direct-coupled pure complementary output capacitorless circuit, FEATURE OF PURE COMPLEMENTARY OCL CIRCUIT Since this circuit is not using output capacitor, the frequency characteristic is kept uniform even at very low frequency band and the output impedance is low in any of frequency bands resulting in that the value of damping factor is made larger so that the braking efficiency of speaker is increased. With this circuit, since a 100 percent NF is assured when the frequency of signal is zero and the value of NF is determined at only one place when the frequency of signal is at low band, the function of ‘circuit is stabilized. CIRCUIT DESCRIPTION ‘The main amplifier is OCL circuit in which the class “A” drive circuit consists of 2 stage differential amplifier circuit from the filter circuit is amplified by differential amplifier (Q502, Q503) via R502 and C504, amplifier consists of PNP type low noise transistor (2SA836D), a high value of S/N ratio is assured, And this amplifier functions to keep zero the center voltage (speaker terminal voltage) as well as to amplify signals. The zero adjustment of potential is to be made by using semi-variable resistor (VR5O1). Signal thus amplified by the differential amplifier is further amplified by differential amplifier (Q504 and Q505). Moreover, the signal is amplified for the half cycle at the driver amplifier stage consisting of Q510 (NPN type transistor) and Q511 (PNP type transistor). Then, the signal is further amplified for the half cycle at Q901 (NPN type transistor) and Q902 (PNP type transistor) to be supplied to the speaker. Q501 and Q506 is constant- current circuit and its amperage is determined by DSO1. Q5O1 functions to protect the differential amplifier (Q502 and Q503) against fluctuations of temperature and voltage resulting in that the center voltage (speaker terminal voltage) is kept constant. (Q506 is constant-current circuit to supply constant current so that the load applied to the class “A” driver Q50S will be reduced thus the gain being increased. As a result of the gain of QSOS being increased by Q506, plenty of NF is produced and so the dis- tortion is lessened. NF factor of NF circuit is determined by R520 and RS17, and the higher NF factor, the higher is the gain. NF factor at the low frequency band is determined by C511 and R517. Q507 and D506 are to cause the bias of class “B” drive stage and to produce idling current of 30 ~ 80:mA so that crossover distortion due to class “B” operation is eliminated. The idling current is to be adjusted by semi-variable resistor (VR502). Q508, Q509, DS02 and D503 are short circuit, etc. at the output section and they detect voltage which will be caused at R528 and R531 (emitter resistor) if current runs excessibely ~ if the detected voltage is higher than as rated, the collector-emitter of Q508(Q509) becomes conductive. DS02(D503) and QS08(Q509) are being located between the base of Q510(Q511) and the center (speaker output) and serve as constant-current circuit, and this results in that the power transistor (Q901,, Q902) is assured of a rating current. SLAD (Spike-less Amplifier Design) CIRCUIT This circuit is a unique circuit out of those in this unit and it actually consists of D504, D505, R527 and R529. In the case of power transistor of class “B” amplifier operation, the most part of input signal is cut off for the half cycle and there arises charge or discharge at the junction according to its capacitance. Therefore, spike-ike voltage is generated or the switching time is disordered against the high frequency signal resulting in that cross-distortion of high frequency band is enlarged. SLAD circuit is for the purpose to prevent such phenomenon as above. Ty Figure 7PROTECTIVE CIRCUIT (Relay Circuit) This circuit is a speaker protection circuit displaying three functions as follows. CIRCUIT DESCRIPTION 1. If DC voltage is produced at the speaker terminal, is enters to the base of Q801 via R813 and R814, When DC voltage is positive, Q801 becomes conductive and when it is negative, Q802 becomes conductive. As a result, a current runs in R807 and the base voltage of Q804 is decreased so that Q804 becomes conductive. Then the base voltage of Q80S is increased and Q80S loses its conductivity, resulting in that no current runs in the relay. With no current running in the relay, the relay switch is put in “OFF” mode, thus no current running in the speaker. 2. When the power switch is set to “ON”, voltage is applied to the base of Q804. Since this base voltage is made lower when (C805 is being charged, no current runs in the relay and the relay switch is put in “OFF” mode (no current runs in the speaker). The duration of charging is determined by the values of C805, R807, R808 and R809. 3. The base of Q803 is given positive voltage by R802 and negative voltage by D801 and R801 as a result of which the base voltage is made to be ~3.5V. When the power switch is set to “OFF”, since positive capacitance is larger than nega! capacitance, the positive voltage is maintained for a while. Thus, the base voltage of Q803 is gradually increased from nega (-3.5V) to positive, Q803 is made conductive, the base voltage of Q804 is decreased, no current runs in the relay to put the relay switch in “OFF” mode and thus the speaker is cut off. It takes about one second for the speaker to be cut off after the power switch is turned off. Figure 8 AF ALIGNMENT FRQGERERE | _atewnen [Mew | Oupw india | Scum] Aauomer Reman Output DC 100mV DC ‘Voltmeter is con- ‘Vohume is mini- Sette Yammer | Notmrseriecor | um potion 1 (Offset Voltage) speaker terminal ‘Other knobs are vases ov Eiweee Inomat pos ton Idle Current 100mVv DC ‘Voltmeter is con- poteren et Vormeter | ycceeaees™ | mum postion 2 imitter of Other knobs are, VRSO2A, Egs8eand | mnormatgoat, | VRS0a8 asmv retin |POWER TRANSISTOR REPLACEMENT. Figure © If it is necessary to replace audio output transistors, then follow these procedures to prevent reoccurrence of transistor failure. 1. Carefully remove transistor and mica isolator and clean all the silicone grease off the mica and the mounting area on the chassis. If the mica is damaged, then it must be replaced. 2. Remove the defective transistor and clean out the transistor mounting hole. 3. Put new silicone grease on the transistor mounting area of the chassis and on both side of the mica isolator. Mount the new transistor, being careful to tighten each. transistor mounting screw evenly. Driving one screw tightly and then the other is likely-to-cause metal filings which may damage the mica or prevent necessary heat dissipation on chassis. 4, Before applying power to the new transistor, with an ‘ohmmeter check to see that there is no short between the transistor case and chassis. 5. As transistor VS2SA757-B/-1 and VS2SC897-B/-1 are almost similar in the shape. So pay attention to the mark of transistor when replacing the power transistor RIPPLE FILTER TRANSISTOR REPLACEMENT. DRIVER TRANSISTOR REPLACEMENT rosnooseaszz ® ~~ N yeas es xBPsozer0s000 Figure 10 Figure 17ALL OPERATIONAL MODES (1) TROUBLE SHOOTING GUIDE (Csvmerom] — [__svmerom [ PROBABLE CAUSE ] WHAT TO DO OR CHECK POINT NO SOUND, ‘AG POWER OK ‘BROKEN OR SHORTED SPEAKER |—xf CHECK CONTINUITY OF SPEAKER ALL MODES CORD NETWORK OF VOICE COIL GORD, AND VOICE COIL REPAIR SROKEN CORD OR RE- PLAGE SPEAKER NOAWAL AT DC }__»[NOT OPERATE RELAY | —+[ CHECK RELAY, 801 ~ GB05 AND DETECTED. VOLTAGE AT 6806 (EMITTER! ‘DEFECTIVE OC |___o{ DEFECTIVE MAIN SUPPLY AMPLIFIER} —»[ REFER TO NEXT DETECTED. NO AC POWER NO POWER AT WALL SOCKET Prov inolcator | | ~WOFONER AT WALL Sot Is.ore DEFECTIVE ONOFF SWITCH OR LINE CORD ‘LOOSE AG PLUG CONTACT BLOWN FUSE ]_—-[iF THE FUSE BLOWS AS SOON AS IT IS REPLACED. “SHORTED POWER TRANSFORMER 901 SHORTED CAPACITOR 6802, C901 ‘SHORTED POWER TRANSISTOR _}—e! a901 ~a908 CHECK CONTINUITY BETWEEN THE SOLLECTOR AND EMITTER, IFT IS SOHN OM CLOSE TO 0 OH TIS Derective ++[SHORTED POWER SUPPLY CIRCUIT |—e{ cHEGK CONTINUITY OF POWER OF POWER AMPLIFIER Surety Gincult L.LGROKEN PRIMARY WINDING OF |—»l CHECK CONTINUITY OF TRANS: POWER TRANSFORMER FORMER POWER INDICA: |-p-+{ DEFECTIVE POWER SUPPLY CIR- || DIVERGENCE OF VOLTAGE speci TOR IS ON, BUT utr FIED IN "SCHEMATIC DIAGRAM” NO SOUND L.fetown Fuse ]__+{TF THE FUSE BLOWS AS SOON AS IS REPLACED. {ypecccrive om snonTeo owen —|—+[as01 ~ ase TRANsisvon t+[Derective on SHORTED Device |—+[SPEAKER SYSTEM, HEADPHONE] Ar ourrur LL [DEFECTIVE AUDIO AMPLIFIER | —x{ DIVERGENCE OF VOLTAGE SPECI. 1 IN "SCHEMATIC DIAGRAM L{BEFECTIVE TRANSISTOR | +[asora 1a) ~ ast1A (8) (WEAK SOUND LOW AG SUPPLY VOLTAGE ] +f GHEGK THE VOLTAGE SELECTOR [ALC MODES faeam L[oEFECTIVE POWER CIRCUIT |__+[ DIVERGENCE OF VOLTAGE sPeGi FIED IN “SCHEMATIC DIAGRAM NO SOUND AT AUX, TUNER DEFECTIVE FUNCTION SWITCH OR |—#l SWa0IA, B, C, SO9O4A (8), SOQ0BA AT ONE Socker i MODE, ‘AT PHONO-1 OR DIVERGENCE OF VOLTAGE SPECI. PHONO? SE FIED IN "SCHEMATIC DIAGRAM" L.{DEFECTIVE FUNCTION SWITCH, IMP ©, 6, SW909, S908, SODOBA' SWITCH, ATT SWITCH OR SOCKET (8), soso7A (a) AT TAPE MODE ]-+[Derective TAPE swiTcH OR SOCKET ‘SWA08A (6), S0902A (B), S0803A (8)ALL OPERATIONAL MODES (2)) SYMPTOM ‘SYMPTOM. PROBABLE CAUSE WHAT TO 00 OR CHECK POINT [DISTORTION REPLACE SPEAK. |—*{DEFECTIVE VOICE COIL, CONE OR REPLACE SPEAKER IN ALL, ER AND OK DAMPER OF SPEAKER MODES OF JOPERATION INSUFFICIENT VOLTAGE OF POWER }—y={ VOLTAGES NOT AS SPECIFIED CIRCUIT. ONE CHANNEL 1S }—#{DEFECTIVE AUDIO FREQUENCY OK, OTHER IS. CIRCUIT DISTORTED [AGING OR WEAK IC OR TRANSISTOR }—*/ 10401, Q5O1A (8) ~ QS5ITA (BI, 901 ~ A904 ‘OPEN OR SHORTS INNEGATIVE _}—*1R520A (B), ABI7A (B), CBTTA (6), FEEDBACK CIRCUIT TONE CIRCUIT HUM IN ALL HIGH LEVEL OF _}—*{DEFECTIVE CONSTANT VOLTAGE }—»{180i, 1602, 7801, 20802 MODES: RIPPLE IN DC GIRCUIT. SOURCE RIPPLE IN POWER |—*{DEFECTIVE CONSTANT voLTAGe |—»{ C903, coos SUPPLY CIRCUIT, CIRCUIT. OF PREAMPLIFIER, ‘SHORT CIRCUIT OF EARTH OF | +[AF UNIT TO CHASSIS, 1901 TO POWER AMPLIFIER OR OTHER CHASSIS AUDIO UNIT TO CHASSIS, ESPE CIALLY HEADPHONE JACK TO CHASSIS. LOUDNESS. VOLUME CONTROL ISINOVER _|—»[NORMAL CONTOUR. REVOLUTION SWITCH DOES NoT DEFECTIVE LOUDNESS CONTOUR | —»[sw404, C401 ~ C404, R407 ~ RAI0 WORK AT '5W404 SWITCH OR CIRCUIT ALL CONTROL BASS CONTROL }—*[DEFECTIVE VAGO3A (a) OR CIRCUIT DOES NOT WORK TREBLE CONTROL, DEFECTIVE VR304A (6) OR CIRCUIT BALANCE CONTROL| | +[DEFECTIVE VRa01A (8) OR CIRCUITFigure 12 TAPE 1/TAPE 2/PRE MAIN/INPUTS CONNECTION BOARD WIRING SIDEFigure 14 MAIN AMP./EQUALIZER AMP./AC & RELAY UNIT BOARD WIRING SIDEsg = ns + eats ar te fi reel patos ree | lng SLL (+ “te nef = rage ry a Go Sl 9: ma poy wat 5 . wel Tog len] [Pie] [tL Gee 8] eee | Len ITF eo a3 coe i t @raaeen ‘ nase Lee can Bee a8 5] aunEeen (la, re aT [me t dee Tas aa faeeeo ol poe ee oa ee ae Fle“ " ; =) ald. of mt bell... fe > Flq plage go 1 eet Nal Sh 4 cas mes cared _ ‘ ; ? IE cnet & d c T x a a = wes arene @\9 pie e@ersvesrey ee oo — Laas fe aRour ES we seatthie Yat ae) 1. cost a 7 Be role ee ro ees ro ri? Pos TO PGB PS-30 o s8888 8 a ° R68. Bthrg 34 ross Oo Thaee PM Me _——Ss my int Racy, ——- = a —s dw 4 o Ue Whhes 7 Cie ma Sm Mme aed ee ne a[ee ot me Ome Teas) sielemem ee ele 8) « he Figure 13 MAIN VOLUME BOARD WIRING SIDEPRE AMP BALANCE MAIN VOLUME ass TREBLE MAIN AMP (L) 901 100K REC/Po (own) $902 sos02f, bert ca39LR = C443. Tous eaarse 1] ")soa} [esoil... wn saree ale "ssi 3{3 2 T 4la4 | 4 ass 's|5) 2a $ 180K SIE mv 1 , sexs] Om w—t Swa08n eeabse ee 7 ‘ BE eon FEI 7 Ssesv + Ue va} sqpors | | te To ee asoa] , p51, Lan tes 2 ca 7 wt tal Psioa Sh isw\ 9 rd: ‘T i + i 2|8}-—9 + om ‘RSOqA 5068 #2) nsfesa leone asl jaw 44 on I efiy ca ° 7 - E = 5 rapa | nase 7 | VR SOB 10K . | + : : : : — Reed Tt " AMP(R) 33968 caso ese case Ses aus aso18 ; OFyaae 19x nt "sox ii )soe| fase: zj2| | 3 sors, als veortov ‘oarov a3 t 95028 5} ' rsoze S048 95038 s}6, Q40),Q402 2SC1345E X 2 soa?) We EQUAL IZE 333” jaso1e 6038 Jg904 foo. 2307] Slnisani f Eee Sree Shey t Soe Leche "3 sos s2o0| i ' f OS01A,8, 05098.8, 25067308 su (Q5024,8, 0503.6, 2508360 a roxas [sosa. 5044,6, 5054.8, OSIOA\P, 2SCI2I2AB at osoe Sw 3018 5068.€, 5118.6. 2Sa743A8 | Q8078,8, 05084, 2sciaisae ro34-4|sosa4 T DSOIA,B, HV-46 X2 s| 5024.8, 0503A,8, 152075 , DS04A.8, O5O5A,8, 182348 7 sea. KOM z 75% 2901 enw HA VJ v901 RED R927 HP AC & RLY UNIT Ee Re sor Sw SOIC oe L R + ‘SP-A a OOF O Jfiises voviev Un, ibov 4 n330 se-8 Btw O-+0 ;TM904 pasa. Ez0riey, v @ loose R340 * E 901,0903 2sca97B 9902,0908 25a7578 = dso! GL-50RG : = +t NO. [FUNCTION] POSITION 71 vl! Sw301a-c [FUNCTION | AUXZ- AUX! 87 gor, ; | PHONO? = PHONO!- TUNER Q301.Q302 2SA836D Q801~Q803 2SCIZI3AB 2 aah e ‘Sw302 ‘MODE R-L-L+R 303-0308 2scis4se Q80s~806 2sA675A8 2]3 FWoRWAL- REVERSE 9309,0310 2SCI212aB 807 2SA743B 3/4 D301, D302 HVE 808 2sci2i23 — || ome TURNOVER | 600ti2 - 300Hz Q809 2sci2izaB ‘ 6 sw402 TURN OVER] |.5KHz- 3KHz e0!,0802 182076 at ad 27 ‘SW403 | TONE | VARIABLE-DEFEAT 803.0804 HV-46 8 = eos 33-3 “t a 3} W404 __| LOUONESS [OFF - ON De0s S8-3R rT ['swaos | AF MUTING|OdB -2048. vaor 151887 se SWAO6 | LOWFILTER [oF - 30Mz Dae Isi9ai wae bow 70801,20802 82140 ‘SWA07 | HIGHFILTER| oF - TKHE 790! amy SWA08A-8 | TAPE [DUBRINGI=2-TAPE I-SOURCE MONITOR |-TAPE2 - DUBBING2=1 ewe swsor_|POWER [ON-OFF | poss sos —|POWER __{ON= OFF _—__ FTN wey PRE/MAIN |NORMAL- SEPARATED NOTES 212 RES BRN enor we 1 ALL RESISTORS ARE SHOWN IN OHMS +5% PS Sat ' re . es PGsor |= 4 CcapaclTORS ARE SHOWN IN, MICROFARADS Mov/eeov/[ | o Pronotattloas-6dB Basar sue 2aov| (© SW8OIA 33 : SPEAKERS [B- OFF-A- A¥B 3. VOLTAGE READINGS ARE MEASURED WITH VTVM r! ale UNDER NO SIGNAL \ ww D5OR yw Razs tbo; 4. SWITCHES ARE SHOWN UNDERLINED POSITION ale sis B 7 = 1 cer ‘C820 og | eee Be. Bisoidov ov woal/S07 e162 7 6 8 yrer t me (Specifications or wiring diagrams of this model are subject to change for the improvement without prior notice.) Figure 15 SCHEMATIC DIAGRAM 7 18sO *P REF. NO, Ic4o1 de sb qe a PART NO. RHAX0427AGZZ de ob ds wp DESCRIPTION Tone Amp. qe oh a ep Figure 16 EQUIVALENT CIRCUIT LHLDW1027AGZ2Z LHLDWIOSOAFZZ LHLDWIOSTAFZZ LHLDW1052AFZZ Figure 17 MISTAKABLE LEAD WIRE HOLDER QCNCMO066IAFZZ (9 Pim) QCNCMO63FAFZZ (6 Pin) QCNCMOS4GAFZZ (7 Pin) Note: This drawing is QCNCMOGSGAFZZ. Figure 18 MISTAKABLE PLUG 19REPLACEMENT PARTS LIST “HOW TO ORDER REPLACEMENT PARTS” To have your order filled promptly and correctly, please furnish the following informations 1, MODEL NUMBER 2. REF. NO. 3. PART NO 4, DESCRIPTION PART No. pescriprion [cove | REF pant no. vescriprion | cove MISCELLANEOUS PSPAZ9004AGZZ Washer, Retaining, Transistor | AA PLETFOLOIAFZ2 —asulatr,Partiton aA GCAB-3001AFSA Cabins az QACCNOOOIAGZZ. Cord, Mans Supply ap GCOVAIOSBAFSA. Guide Lever Switch a QACCS9OOISED0. Cord. Mans Suply AG GETAU30SoAFZ2 Pte, Botiom aN QACCVOOOIAGZ2. Cord, Mains Suply AN GLECPO002SCOO Leg aD QACCz0002TAOF Cord, Main Supply AG HDECWOOSOAFSS Board, Right @ LeftHand | aR | FOI, Side ro2, HPNLC3219AFSA Plate, Operation BB | PG3, OCC MOS LCALZZ aed bli Ein oe TKNBNOZ?2AESA Knob, VOLUME AP | Foe IKNBNODTBAFSA._—_Keob, FUNCTION AN | Fon, IKNBNODTAAFSA. Knob, SPEAKERS/BASS/ | AL | PG28'| QCNCMOSSEAFZZ Pug, Pin a> TREBLE/BALANCED ro26 MODE/TAPE MONITOR ror, JKNBPOOSEAFSA Knob, POWER/TURNOVER/ | AH | PGE, LOWCUT/HIGHCUT/ PG(30} QCNCMOS4FAFZZ — Plug, 6 Pin AD. LOUDNESSIMUTING =| LANGQO439AFSA Bracke, Terminal at | Fa] QcNeMosscarzz —Piug,7 Pin ae LANGRO3SOAr22 Bracket Operation Pate | AK QENCMOGOFAFZZ Pigs 6 ar TANGTO(SIAF22 Bracket, Suengthen Left & | AE QencMosAGArZ2 Phe, 1 Pin AG Tent Hand Side QENCHOGSIAFZZ Plu. 9 Pin aH LANGTOAS2AFZZ Bracket, Printed Wiring | AC | FG34QCNEMOISEAFZZ. Pug S Pin ac Beud FG35OCNCMOTAFAPZZ_— Puts 6Pin ac LANGTOAS3APZZ.— Brett ac | 03, TANGTOASEAFZZ Bracket, PHONO Terminal | AB | soil, Pw $013, LBSHCOOO4AFZZ Bushing, Mains Supply Cord | Ac | Sota: | QCNCWOSOPAFZZ Socket, Pin ac LBSHCOOO7AF22 Bushing, Main Supply Cord | AB | S018, LeHSMO20IAF22. Pate, Mounting ak | $020, LHLDWiO27AGz2 Holder Led Wire aA | 8023 LHLDWI0SoarZ2 Holder Led Wie ae | sor, LHLDWLOSLAZ2 Holder Led Wise ab | S02, LHLDWi0s2AFZ2 Holder, Lead Wie aa | 503, LHLDW9003¢Ez2 Holder Lad Wise a | S06, LHLDZ90S0AF0O Holder, LED AV | So10, OCHCNOS LCAEZZ Sa Sosket 3 2a) id LXNZS0G0SEFN Nut, Headphonesaux2 | aA | S015, ack soir, LXx.w23017CEFN Washer, GND Termina) | aa | S019 POOVS30S0AFO0 Cover, Sie, Front, AP | S016 Qcnewos2DAFZz Socket, 4Pin ac POOVS30S1AFOO Cover, Shield Rear AM | 8025.1 Gene POOVS30S24F22 Bracket, Purtion, Power | AD | Soze' | QCNCWOSSEAFZZ. Socket, Pin cS Switch sor, POOVW3I01AFZZ Cover, Fuse Holder, Acrytic | AF | S08, PRDAROOSBAGZ2, Heats, Stl Transistor | AA | SO12, (Q807, 0808) S021; | acnowossrarZz. Socket, 6 Pin ac PRDAROIOOAFOO Heatsink, Large, Power | AW | $030, Transstor S031, PRDAROLOIAFFW Heats Small Transtor | AB | S032 PSHEFOOSBAGOO Feit, caine AA | S08" QCNCWOSSGAFZZ Socket, Pin ac FSHEFOLIOAFZ2 Fel Masking, Lover Switch | AA | S036 PSPANOO04AF09- ‘Spacer, Headphone Jack, AB | so39 | QCNCWO63FAFZZ Socket, 6 Pin oo TAUX 2 ack $037, PSPAPOOI2AGZ2 Washer Handphone Jack, | AA | S038 she, Hen $038.1 goncwossuarZz Socket, 8 Pin ar PSPAZOOSOAFZ2 nto, Power Transistor | 4B | S081REF. ‘No. $042 $034 $035 PART NO. QCNCWOS6IAFZZ QCNCWOTLEAFZZ. QCNCWO72FAFZZ QCNCWOROFAFZZ, QFS-DI6LAAGNI OFS.C2S2CAGNI F801 , F802 QFSHD1001AGZz, QHWS-3001 AGEN QUAKz0021AG2z QUAKE0027AGZZ QLUGLOSIICEZZ QLUGPOIOSAGZz QLUGPO11CEFW QPLGA020SAGZz OPLGSOISOAFZz 3902 3901 ‘QPWBED0S2AFZZ (QPWBEOOS3AFZZ QPWBEOOS4AFZz QPWBEDOSSAFZZ QPWBEDO6OAFZz QPWBFO3S2AF ZZ QPWBFO3S3AFZZ QPWBFO3S4AFZZ QPWBFO423AFZZ 0901, 0906, 0907 0904, | 80905 | Qsocy24s0aFzZ, asocrssiarzz asocrzsoarzz | asocensoarzz QSW-BOOSOAFZZ $0902, $0903 swaol ‘$W402_QSW-BOOSOAFZZ ‘sw403 ‘sw404 ‘sw40s ‘$W406 sw407 ‘sw901 sW302 swaos (A.B) sos w301 (A.B, sw902 (QSW-BOOSIAFZZ, (QSW-BO0S1AFZZ (QSW-B00S1AFZZ (QSW-BOOSIAFZZ QSW-BO0SLAFZZ (QSW-B9OS9AFZZ (QSW-ROLOLAFZZ, aswnoiosaezz Josmnoniarez QSW-SOISOAFSA 906 aswsorsoarsa swoo Gonsolstarsn 0, N90!) ANZoIsOAFSA PARTS LIST DESCRIPTION Socket, 9 Pin Socket, 5 Pin Socket, 6 Pin Socket, Fuse, 160mA Fuse, 254, RATED LINE VOLTAGE. Holder, Fuse Jack, AUX 2 Jack, HEADPHONES Lug Terminal, 4 Pin Lug Terminal, Test Point Lug Terminal Plug, Mains Supply Cord Plug, Short Circuit, PHONO 1/ PHONO 2 Printed Witing Board, Power Amp. Printed Wiring Board, TONE, ‘Amp. Printed Wiring Board, Volume Printed Wiring Board, Equalizer Printed Witing Board, Power Supply Printed Wiring Board, PRE/ MAIN CONNECTION Printed Wiring Board, TAPE-1/ TAPE-2 Printed Wiring Board, IMP./ PHONO-2/PHONO-1/ATT Printed Witing Board, Fuse Socket, PRE/MAIN CON- ‘NECTION, PHONO-1/ PHONO? Socket, TUNER/AUX Socket, Power Transistor Socket, TAPE+I/TAPE-2 Switch, TURNOVER, 300H2/600H2 Switch, TURNOVER, 1L.Sktlz/3kH2 ‘Switch, VARIABLE/DEFEAT Switch, LOUDNESS Switch, MUTING ‘Switch, LOWCUT ‘Switch, HIGHCUT Switch, POWER ‘Switch, MODE Switch, TAPE MONITOR ‘Switch, SPEAKERS Switch, FUNCTION Switch, NORMAL/ SEPARATED Switch, ATT ‘Switch, IMP Terminal, GND cope AF AE, AE, ac AE AE, AB AA AH AF Ac AA AA AK Ac AM AP AN An AL AD AD AD AD AG AG AD Ak AL AL AK AK AK AK AK AK AN As AL AK AF AF AD 2 PART NO. DESCRIPTION Terminal, SPEAKERS Washer, Rubber Headphone Jack | oranzossoarzz xownicoa-asias C442 eee Aluminum Electrolytic £301.) vcpoaraacszam —023MFD. 1000, +20 206, C904 SCE S ED IEE Loe Electrolytic RESISTORS R337) gp vzooorarzz na eo TP] vnseranex 22h shn 0108, S03 | vmwcrappionx 1c. 2¥. 10 10%, (A,B) Re TSU Zaa Wire Wound CONTROLS ¥RO0! | pyecooo4aGz2 BALANCE ¥R302 | qypsoiiaar2z VOLUME VAS03 | aya.consoarz BASS Mia VRO06 | ayR.coosoaF22. TREBLE YRSO? | gyRaon4sAG22 deren Adjust | wvewoor2acz2 center Vonage Ad (AB) TRANSISTORS 9301, Constant Current 9302 quate Circuit | vsasasnenes cove AN AA AA AA ac AE AX AD AD AA AA AB AB AB AC ac AD AL AL AL AL AF AG AEPARTS LIST SEE pant no. escrierion cove) SEF pant no. Descnirrion cone 0303, 9304 | VS28C1345-E-1 Equalizer, Differential Amp. ‘AE DIODES 830s, . aoe] wsciese1 enti oteein'amn. | at |.) suvaccit — Bu.consnrcuren | gy 9307, i Equalizer, Emitter Follower rout aoe | vssciseses POE Ae | S01 | vaivaccitt constant Curent Creat | AD 30, ; Qa10 | YSISCIZIIWABE—Egentze,Cls"A" AM. | AH) BSE? | vprszoreid Vota Detector ac Q401, Loweut Filter, Emitter _ aos’ | YS2SCI3SEL Perret ae |DS03 | vupiszoreisd —Yolage Deter Ac Os01 power Ap, Constant 5 (A,B) Rea Ae LT Current Circuit AG | D804 | iipis2348-H-1 Spike-less Amp. AD O80? | veagasseea —PowerAmp.Dierentat— | gp | ME we ‘mss SOS | yuisaaeeii1 — Spketess Amp a0 03 jy Poet Ap Dilferenia . tay | YSSARED AE | DS06 | yuvmvaosvii4 Bis Creu ao 9504 Power Amp., Differential By 2506) vsascarawane Power np, ast | Deol vupiszonsiet Detector AG Qs0s can Power Amp. Differential D802 VHD1S2076//-1 ‘Surge Current Provention AG Ga | YSISC2I2W AR ad AM) EOS.) varvnvasciet Ripple FierCreit aD oe ve Ap Conn 2806 | ysasanaaanya Powerman consamt |g | OH pss Rete ax ocar D805 VHDSS-3R///-F Rectifier aM 2807 | ysascr2i3Aei power Amp, Bas Creat | aF | peo) VIDISIBNH/;a Rese a 508 D808 VHDISI941//-1 _—_—Rectfier AD VSISCI213AB-1 Power Amp, Votage Detector] AF a Power Amp. Voge Ds D801 yuesziaqid Ripple Fier Cnc Ac 2509 | vsrsA673ABs1 Power Amp, Volage Detector] AG | DOO” VHRGLSORG// —ndkatr ne wo VS2SC1213WAB4 Power Amp., Driver Amp. AH (A,B) COILS O81 | vsasareaanid poner Amp.Diveramp. | aL | : ReIL2OnS0A22 4 ao SSS) vsascizisaps —Motection Creu Senter | gp | (A: 2) Q803 | VS2SC1213AB-1 Protection Circuit, Power Off | AF | rgo2 | V?-LH470M0000 aie ap Gos WSrSAc73Ab/1 Proven Geaut,Sechng |G Gos YS8A673A8/1 Protection Great Switching | AG Q806 = VS2SA673AB/-1 Protection Circuit, Switching | AG ‘TRANSFORMER GsorWSISA7/I Mae SuppcvcancRipe | AK titer 1901 RTRNPO:B5AFZ2_ Power oe 0808 VS2SC1212B1 Malm SupptyCheut, Ripple | Att Pier 809 VSISCI212WABE Main Supply Crcu.Rigte | AH INTEGRATED CIRCUIT rier 01.) ysascasras pane Amp ag | 1101 RIAXOA27ACZ Tone Amp ae O302, 9902. | ysasarsrn¢d Power Amp. at nctay nev to | rtvzonsoarzz aw a) 2800-1 Pin es