SLA6868MZ and SLA6870MZ

High Voltage 3-Phase Motor Drivers

Features and Benefits Description

▪ Built-in pre-drive IC
The SLA6868MZ and SLA6870MZ inverter power module
▪ MOSFET power element
(IPM) ICs provide a robust, highly-integrated solution for
▪ Alleviate noise generation by adjusting an internal resistor
optimally controlling 3-phase motor power inverter systems
▪ CMOS compatible input (5 V)
and variable speed control systems used in energy-conserving
▪ High-side gate driver using bootstrap circuit or floating
designs to drive motors of residential and commercial
power supply

ns
appliances. These ICs take 230 VAC input voltage, and up to
▪ Built-in protection circuit for controlling power supply
3 A (continuous) output current. They can withstand voltages
voltage drop (UVLO on VCC)

ig
of up to 500 V (MOSFET breakdown voltage).
▪ Overcurrent protection (OCP), overcurrent limiting (OCL),
and thermal shutdown (TSD) The SLA power package includes an IC with all of the necessary

es
▪ Output of fault signal during operation of protection circuit power elements (six MOSFETs), pre-driver ICs (two), and

D
▪ Output current 1.5, 2.5, or 3 A bootstrap diodes (three), needed to configure the main circuit
▪ Small SIP (SLA 24-pin) of an inverter. This enables the main circuit of the inverter to

ew
Packages: Power SIP be configured with fewer external components than traditional
designs.
Not to scale

rN
Applications include residential white goods (home
applications) and commercial appliance motor control:
• Air conditioner fan
fo
• Small ventilation fan
Leadform
• Dishwasher pump
d

2171 Leadform 2175

de

Functional Block Diagram

en

VB1 VB2 VB3

m

VCC1
m

VBB
UVLO UVLO UVLO UVLO
o

HIN1
ec

Input High-Side
HIN2 Logic Level Shift Driver
HIN3
R

COM1
W1
SD1 W2
ot

V
VCC 2 U
UVLO
N

LIN1
Input Logic Low-Side
LIN2
(OCP Reset ) Driver
LIN3
COM2 OCP
Thermal
LS 2
Shutdown
SD2 OCP and OCL LS1
OCL
RC

A. S̄¯¯D̄¯1̄¯ , S̄
¯¯D̄
¯2̄¯ terminals are used for both input and output.
B. S̄¯¯D̄
¯1̄¯ , S̄¯¯D̄
¯2̄¯ , and Ō¯¯C̄¯L̄¯ terminals are open-collector output. RC terminal is open-drain input.
C. Blanking Time (tblank) is used in Overcurrent Limiting (OCL) and Overcurrent Protection (OCP).
If the time exceeds the limit, the signal will be output (open-collector output turns on), and protection
Figure 1. Driver block diagram. operation will start up.

28610.09, Rev. 6
SANKEN ELECTRIC CO., LTD.
http://www.sanken-ele.co.jp/en/
SLA6868MZ and
SLA6870MZ High Voltage 3-Phase Motor Drivers

Selection Guide
MOSFET Breakdown Output Current
Part Number Voltage, VDSS(min) Continuous, IO(max) Pulsed, IOP (max)
(V) (A) (A)
SLA6868MZ 500 2.5 3.75
SLA6870MZ 500 3 4.5

ns
Absolute Maximum Ratings, valid at TA = 25°C

ig
Characteristic Symbol Remarks Rating Unit

es
MOSFET Breakdown Voltage VDSS VCC = 15 V, ID = 100 μA, VIN = 0 V 500 V
Logic Supply Voltage VCC Between VCC and COM 20 V

D
Bootstrap Voltage VBS Between VB and HS (U,V, and W phases) 20 V
SLA6868MZ 2.5 A

ew
Output Current, Continuous IO
SLA6870MZ 3 A
SLA6868MZ 3.75 A
Output Current, Pulsed

Input Voltage
IOP

VIN
SLA6870MZ
HINx and LINx pins
rN
PW ≤ 100 μs, duty cycle = 1%
4.5
–0.5 to 7
A
V
fo
Pull-up Voltage for Shutdown Pins VSDX S̄¯¯D̄¯x̄¯ pins 7 V
Pull-up Voltage for Overcurrent Limiting Pin VOCL 7 V
d

Allowable Power Dissipation PD TC = 25°C 32.9 W

de

Thermal Resistance (Junction to Case) RθJC All elements operating 3.8 °C/W
Case Operating Temperature TCOP –20 to 100 °C
en

Junction Temperature (MOSFET) TJ 150 °C

Storage Temperature Tstg –40 to 150 °C
m
o m
ec
R
ot
N

All performance characteristics given are typical values for circuit or

system baseline design only and are at the nominal operating voltage and
an ambient temperature, TA, of 25°C, unless otherwise stated.

28610.09, Rev. 6 2
SANKEN ELECTRIC CO., LTD.
SLA6868MZ and
SLA6870MZ High Voltage 3-Phase Motor Drivers

Recommended Operating Conditions

Characteristic Symbol Remarks Min. Typ. Max. Units

ns
Main Supply Voltage VBB Between VBB and LS – – 400 V
VBB Snubber Capacitor CSB 0.01 – 0.1 μF

ig
Logic Supply Voltage VCC Between VCC and COM 13.5 15 16.5 V

es
Zener Voltage for VCCx Pins VZ Between VCC and COM 18 – 20 V

Pull-up Voltage VSDx, VOCL 4.5 5 5.5 V

D
Pull-up Resistor S̄¯¯D̄¯¯
x̄ Pins RUP2 3.3 – 10 kΩ

ew
Pull-up Resistor OCL Pin RUP1 1 – 10 kΩ

Pull-up Resistor RC Pin RR 33 – 390 kΩ

Capacitor S̄¯¯D̄¯¯

Capacitor RC Pin
x̄ Pins CSDX

CC
rN 1

1
–

–
10

4.7
nF

nF
fo
Dead Time tdead TJ = –20°C to 150°C 1.5 – – μs

IINMIN(on) TJ = –20°C to 150°C 0.5 – – μs

d

Minimum Input Pulse Width

IINMIN(off) TJ = –20°C to 150°C 0.5 – – μs
de

Switching Frequency fPWM – – 20 kHz

en
m
o m
ec
R
ot
N

28610.09, Rev. 6 3
SANKEN ELECTRIC CO., LTD.
SLA6868MZ and
SLA6870MZ High Voltage 3-Phase Motor Drivers

Typical Application Diagram

Shows configuration for implementing current
¯¯C̄
limiter function: Ō ¯L̄¯ and S̄¯¯D̄¯1̄¯ pins tied together

1 2 3
SLA6868MZ
SLA6870MZ

10
VB1 VB2 VB3

ns
VCC1 HO 1
4
24
5V DZ1 HS1

ig
RUP1
CSD1

es
HVIC HO 2
5
SD1 12
HS2 M

D
9
HIN 1
8
HIN 2
7
HIN 3 HO 3

ew
6 11
COM1 HS3

rN
13
CSB
23
VCC 2
fo
DZ2
LO 1

17
d

OCL
MC U LVIC
de

20
LIN1
19 LO 2
LIN2
en

18 16
LIN3 RS
m

RR
LO 3
5V
15
m

RC 14
5V
CC RUP2
o

22
SD2
CSD2
ec

21
COM 2
R

15 V
ot
N

NOTE:
▪ The external electrolytic capacitors should be placed as close to the IC as possible, in order to avoid malfunctions from
external noise interference. Put a ceramic capacitor in parallel with the electrolytic capacitor if further reduction of noise
susceptibility is necessary.

28610.09, Rev. 6 4
SANKEN ELECTRIC CO., LTD.
SLA6868MZ and
SLA6870MZ High Voltage 3-Phase Motor Drivers

Typical Application Diagram

Shows configuration without current limiter
¯¯D̄¯1̄¯ and S̄¯¯D̄¯2̄¯ pins tied together
function: S̄

1 2 3

SLA6868MZ
SLA6870MZ

ns
10
VB1 VB2 VB3
4
VCC1 HO1

ig
24
ZD HS1

es
5V

HO2

D
Rup
Rup1
5
SD1 12
9
HS2 M
HIN1

ew
8
HIN2
7
HIN3 HO3

6 11

CSD
23
COM1
HVIC
HS3

rN 13
fo
VCC2

ZD

LO1
d

17
OCL
de

20
LIN1
19 LO2
en

LIN2
18 16
LIN3 RS
m

RR
LO3
VRC
m

15
RC 14

CC
o

22
SD2
ec

21
COM2 LVIC
R

15V
ot
N

NOTE:
The external electrolytic capacitors should be placed as close to the IC as possible, in order to avoid malfunctions
from external noise interference. Put a ceramic capacitor in parallel with the electrolytic capacitor if further
reduction of noise susceptibility is necessary.

28610.09, Rev. 6 5
SANKEN ELECTRIC CO., LTD.
SLA6868MZ and
SLA6870MZ High Voltage 3-Phase Motor Drivers

ELECTRICAL CHARACTERISTICS, valid at TA=25°C, unless otherwise noted

Characteristics Symbol Conditions Min Typ Max Units
SLA6868MZ – 4.2 7 mA
Logic Supply Current ICC VCC = 15 V, TC = –20°C to 125°C
SLA6870MZ – 2.7 5.0 mA
Bootstrap Supply Current IBX VBX = 15 V, VHIN = 5 V – 135 380 μA
VIH VCC = 15 V – 2.9 3.4 V
Input Voltage
VIL VCC = 15 V 1.6 2.1 – V

ns
Input Voltage Hysteresis VIhys VCC = 15 V – 0.8 – V
Input Current IIN VIN = 5 V – 230 500 μA

ig
VUVHL 9.0 10.0 11.0 V
High side, between VBx and U, V, or W

es
VUVHH 9.5 10.5 11.5 V
VUVHhys High side, hysteresis – 0.5 – V

D
Undervoltage Lock Out
VUVLL 10.0 11.0 12.0 V
Low side, between VCC2 and COM2

ew
VUVLH 10.5 11.5 12.5 V
VUVLhys Low side, hysteresis – 0.5 – V
VSDX(on),
SDx and OCL Output Voltage

Overtemperature Detection Threshold

VOCL
TDH
rN
VSDX = VOCL = 5 V, RUPX = 3.3 kΩ –

120
–

135
0.6

150
V

°C
fo
Temperature (Activation and TDL VCC = 15 V, high-side and low side 100 115 130 °C
Deactivation)
TDhys – 20 – °C
d

Overcurrent Protection Trip Voltage VTRIP VCC = 15 V 0.9 1.0 1.1 V

Overcurrent Limit Reference Voltage VLIM VCC = 15 V 0.5035 0.53 0.5565 V
de

Overcurrent Protection Hold Time tp VRC = 5 V, RR = 360 kΩ, CC = 0.0047 μF – 2.0 – ms

en

Blanking Time tblank VCC = 15 V 1.4 2.0 2.6 μs

Bootstrap Diode Leakage Current ILBD VR = 250 V – – 10 μA
m

SLA6868MZ – 1.1 1.3 V

Bootstrap Diode Forward Voltage VFBD IF = 0.05 A
SLA6870MZ – 0.8 1.3 V
m

Bootstrap Diode Recovery Time trrb IF / IRP = 100 mA / 100 mA – 70 – ns

o

Bootstrap Diode Series Resistor RBD 168 210 252 Ω

ec

MOSFET Breakdown Voltage VDSS VCC = 15 V, ID = 100 μA, VIN = 0 V 500 – – V

MOSFET Leakage Current IDSS VCC = 15 V, VDS = 500 V, VIN = 0 V – – 100 μA
R

SLA6868MZ VCC = 15 V, ID = 1.5 A, VIN = 5 V – 2.0 2.4 Ω

MOSFET On State Resistance RDS(on)
SLA6870MZ VCC = 15 V, ID = 1.25 A, VIN = 5 V – 1.4 1.7 Ω
ot

SLA6868MZ VCC = 15 V, ISD = 1.5 A, VIN = 0 V – 1.1 1.5 V

MOSFET Diode Forward Voltage VSDF
N

SLA6870MZ VCC = 15 V, ISD = 1.25 A, VIN = 0 V – 1.0 1.5 V

28610.09, Rev. 6 6
SANKEN ELECTRIC CO., LTD.
SLA6868MZ and
SLA6870MZ High Voltage 3-Phase Motor Drivers

SLA6868MZ SWITCHING CHARACTERISTICS, valid at TA=25°C, unless otherwise noted

Characteristics Symbol Conditions Min Typ Max Units
tdH(on) – 790 – ns
trH – 60 – ns
Switching Time, High Side trrH VBB = 300 V, VCC = 15 V, ID = 2.5 A, 0 V ≤ VIN ≤ 5 V – 115 – ns
tdH(off) – 725 – ns

ns
tfH – 20 – ns
tdL(on) – 680 – ns

ig
trL – 70 – ns
Switching Time, Low Side trrL VBB = 300 V, VCC = 15 V, ID = 2.5 A, 0 V ≤ VIN ≤ 5 V – 120 – ns

es
tdL(off) – 605 – ns

D
tfL – 20 – ns

ew
SLA6870MZ SWITCHING CHARACTERISTICS, valid at TA=25°C, unless otherwise noted
Characteristics Symbol
tdH(on)
trH
rN
Conditions Min
–
–
Typ
755
65
Max
–
–
Units
ns
ns
fo
VBB = 300 V, VCC = 15 V, ID = 2.5 A, 0 V ≤ VIN ≤ 5 V,
Switching Time, High Side trrH – 100 – ns
inductive load
tdH(off) – 680 – ns
d

tfH – 15 – ns
de

tdL(on) – 645 – ns
en

trL – 70 – ns
VBB = 300 V, VCC = 15 V, ID = 2.5 A, 0 V ≤ VIN ≤ 5 V,
Switching Time, Low Side trrL – 105 – ns
inductive load
m

tdL(off) – 560 – ns
tfL – 20 – ns
om
ec
R
ot
N

28610.09, Rev. 6 7
SANKEN ELECTRIC CO., LTD.
SLA6868MZ and
SLA6870MZ High Voltage 3-Phase Motor Drivers

IN
trr
ton toff
td(off) tf
VDS td(on) tr

ns
90% 90%

ig
ID

es
10% 10%

D
Switching Characteristics Definitions

ew
rN
fo
d
de
en
m
o m
ec
R
ot
N

28610.09, Rev. 6 8
SANKEN ELECTRIC CO., LTD.
SLA6868MZ and
SLA6870MZ High Voltage 3-Phase Motor Drivers

Truth Table
Mode Hin Lin H-side MOSFET L-side MOSFET
L L Off Off
H L On Off

ns
Normal
L H Off On
H H On On

ig
L L Off Off

es
H L On Off
TSD
L H Off Off

D
H H On Off

ew
L L Off Off
H L On Off
OCP

H
L

L
H
H
L
rN Off
On
Off
Off
Off
Off
fo
H L Off Off
Ō¯¯C̄¯L̄¯ ( = L )1
L H Off On
d

H H Off On
de

L L Off Off
H L Off Off
en

UVLO ( VCC )2
L H Off Off
H H Off Off
m

L L Off Off
m

H L Off Off
UVLO ( VB )3
L H Off On
o

H H Off On
ec

L L Off Off
R

H L On Off
S̄¯¯D̄¯2̄¯ ( = L )
L H Off Off
ot

H H On Off
1The OCL feature is enabled when the Ō ¯¯C̄¯L̄¯ and S̄¯¯D̄¯1̄¯ pins are tied together externally. If these pins are not tied when an
N

OCL condition occurs, device operation continues in Normal mode.

2Returning to the Normal mode of operation from a V
CC UVLO condition, a high-side MOSFET resumes switching
on the rising edge of an HINx input. On the other hand, a low-side MOSFET resumes switching on the first logic high
of a LINx input after release of the UVLO condition.
3Returning to the Normal mode of operation from a V UVLO condition, a high-side MOSFET resumes switching on the rising
B
edge of an HINx input.

Note: To prevent a shoot-through condition, the external microcontroller should not drive HINx = LINx = H at the same time.

28610.09, Rev. 6 9
SANKEN ELECTRIC CO., LTD.
SLA6868MZ and
SLA6870MZ High Voltage 3-Phase Motor Drivers

OCP Timing Diagram

LIN

LO

ns
VTRIP

ig
LS1

es
tblank
OC P

D
Release

S D2

ew
tp

RC
rN 3.5 V

Slope defined by RC, CC

fo
d
de
en

Low-Side TSD Timing Diagram

m
o m
ec
R
ot
N

Open-collector output transistor

turned on in low state

28610.09, Rev. 6 10
SANKEN ELECTRIC CO., LTD.
SLA6868MZ and
SLA6870MZ High Voltage 3-Phase Motor Drivers

High-Side UVLO Timing Diagram

ns
ig
es
D
ew
rN
fo
d
de

Low-Side UVLO Timing Diagram

en
m

LIN
mo

UVLH UVLH
VCC2
ec

UVLL
R
ot

LO
N

Open-collector output transistor

SD2 turned on in low state

28610.09, Rev. 6 11
SANKEN ELECTRIC CO., LTD.
SLA6868MZ and
SLA6870MZ High Voltage 3-Phase Motor Drivers

OCL Timing Diagram

Ō¯¯C̄¯L̄¯ and S̄
¯¯D̄¯1̄¯ pins connected externally

Enable resumption of high-side

operation at next HIN rising edge

ns
HIN
Enable resumption of low-side

ig
operation at next LIN rising edge

es
LIN High-side High-side
shutdown shutdown

D
HO

ew
3.3 μs 3.3 μs

Low-side shutdown

LO
rN
fo
VTRIP (1 V)

LS1 VOCL (0.5 V)

d

2 μs 2 μs
de

2 μs
en

OCL, VTH (2.1 V) VTH (2.9 V) VTH (2.9 V)

SD1
m

VTH (2.1 V)
m

T= 50 Cf T= RL×Cf T= RL×Cf

o

VTH (2.9 V)
SD2
ec

T= 50 C2
T= R2×C2
R

3.5 V
RC
ot

T= 50 CC
T= RR×CC
N

5 μs

28610.09, Rev. 6 12
SANKEN ELECTRIC CO., LTD.
SLA6868MZ and
SLA6870MZ High Voltage 3-Phase Motor Drivers

Shut Down Timing Diagram

S̄¯¯D̄
¯1̄¯ and S̄¯¯D̄¯2̄¯ pins connected externally; current-limiter function not in use

ns
HIN(a)

ig
LIN(a)

es
D
ew
Slope defined by RC, CC

rN
fo
d
de
en
m

(a) Each HINx or LINx pin drives a independent side of a phase, that is, the high-side and the
low-side swtiching devices of a U, V, or W motor coil phase are each driven separately, by the
m

corresponding dedicated HINx or LINx input

o
ec
R
ot
N

28610.09, Rev. 6 13
SANKEN ELECTRIC CO., LTD.
SLA6868MZ and
SLA6870MZ High Voltage 3-Phase Motor Drivers

Pin-out Diagram

Leadform 2171 Leadform 2175

1 3 5 7 9 11 13 15 17 19 21 23

2 4 6 8 10 12 14 16 18 20 22 24
Pad Side

ns
1 3 5 7 9 11 13 15 17 19 21 23

ig
es
2 4 6 8 10 12 14 16 18 20 22 24

D
ew
Terminal List Table
Number Name
rN Function
Pad Side
fo
1 VB1 High side bootstrap terminal (U phase)
2 VB2 High side bootstrap terminal (V phase)
d

3 VB3 High side bootstrap terminal (W phase)

de

4 VCC1 High side logic supply voltage

5 ¯¯D̄¯1̄¯
S̄ High side shutdown input and UVLO fault signal output
en

6 COM1 High side logic GND terminal

7 HIN3 High side input terminal (W phase)
m

8 HIN2 High side input terminal (V phase)

m

9 HIN1 High side input terminal (U phase)

10 VBB Main supply voltage
o

11 W1 Output of W phase (connect to W2 externally)

ec

12 V Output of V phase
R

13 W2 Output of W phase (connect to W1 externally)

14 LS2 Low side source terminal (connect to LS1 externally)
ot

15 RC Overcurrent protection hold time adjustment input terminal

16 LS1 Low side source terminal (connect to LS2 externally)
N

17 Ō¯¯C̄
¯L̄¯ Output for overcurrent limiting
18 LIN3 Low side input terminal (W phase)
19 LIN2 Low side input terminal (V phase)
20 LIN1 Low side input terminal (U phase)
21 COM2 Low side GND terminal
22 S̄¯¯D̄¯2̄¯ Low side shutdown input and overtemperature, overcurrent, and UVLO fault signals output
23 VCC2 Low side logic supply voltage
24 U Output of U phase

28610.09, Rev. 6 14
SANKEN ELECTRIC CO., LTD.
SLA6868MZ and
SLA6870MZ High Voltage 3-Phase Motor Drivers

Package Outline Drawing

Leadform 2171
Dual rows, 24 alternating pins; vertical case mounting; pin #1 on pad side

Exposed

ns
heatsink pad
31.3 ±0.2
31 ±0.2

ig
24.4 ±0.2
16.4 ±0.2 4.8 ±0.2

es
0.6
Gate protrusion
1.7 ±0.1

D
Ø3.2 ±0.15 Ø3.2 ±0.15

2X Gate protrusion

ew
16 ±0.2 B 2.45 ±0.2
BSC
12.9 ±0.2 Heatsink

rN
exposed
9.9 ±0.2 2X Exposed this side
tie bar
Branding Area
fo
R1
REF
5 ±0.5
d

9.5 +0.7
– 0.5 +0.15
0.5 – 0.05
de

4.5
View A 1.27 ±0.7 A REF 4.5 ±0.7
0.6 +0.15
en

– 0.05
m

2 4 6 8 10 12 14 16 18 20 22 24
o m

1 3 5 7 9 11 13 15 17 19 21 23
0.7 MAX
ec

0.7 MAX
Deflection at pin bend
A Measured at pin tips View A
R

B To case top
Leadform: 2171
Terminal core material: Cu
ot

Terminal plating: Ni
Recommended attachment: Solder dip (Sn-Ag-Cu)
N

Dimensions in millimeters
Branding codes (exact appearance at manufacturer discretion):
1st line, type: SLA6868MZ or SLA6870MZ

2nd line, lot: YMDD#

Where: Y is the last digit of the year of manufacture
M is the month (1 to 9, O, N, D)
DD is the date
# is the tracking letter

Leadframe plating Pb-free. Device composition

complies with the RoHS directive.

28610.09, Rev. 6 15
SANKEN ELECTRIC CO., LTD.
SLA6868MZ and
SLA6870MZ High Voltage 3-Phase Motor Drivers

Package Outline Drawing

Leadform 2175
Dual rows, 24 alternating pins; pins bent 90° for horizontal case mounting; pin #1 in outer row

Exposed

ns
heatsink pad
31.3 ±0.1
31 ±0.2

ig
24.4 ±0.2
16.4 ±0.2 4.8 ±0.2
0.6

es
Gate protrusion
1.7 ±0.1

D
Ø3.2 ±0.15 Ø3.2 ±0.15

2X Gate protrusion

ew
16 ±0.2 B 2.45 ±0.1
BSC
12.9 ±0.2

rN 9.9 ±0.1 3 ±0.3 2X Exposed

BSC tie bar
Branding Area

2.2 ±0.6
BSC
fo
R1
4.4 REF
REF
d

0.6 +0.2 1.27 ±0.2 A 2.2 ±0.6

View A – 0.1 BSC 0.5 ±0.1
de
en

1 2 3 5 7 9 11 13 15 17 19 21 23
4 6 8 10 12 14 16 18 20 22 24
m
o m

0.7 MAX
0.7 MAX
ec

Deflection at pin bend

A Measured at pin exit from case View A
R

B To case top
Leadform: 2175
Terminal core material: Cu
ot

Terminal plating: Ni
Recommended attachment: Solder dip (Sn-Ag-Cu)
N

Dimensions in millimeters
Branding codes (exact appearance at manufacturer discretion):
1st line, type: SLA6868MZ or SLA6870MZ

2nd line, lot: YMDD#

Where: Y is the last digit of the year of manufacture
M is the month (1 to 9, O, N, D)
DD is the date
# is the tracking letter

Leadframe plating Pb-free. Device composition

complies with the RoHS directive.

28610.09, Rev. 6 16
SANKEN ELECTRIC CO., LTD.
SLA6868MZ and
SLA6870MZ High Voltage 3-Phase Motor Drivers

Because reliability can be affected adversely by improper • Please select suitable screws for the product shape. Do not
storage environments and handling methods, please observe use a flat-head machine screw because of the stress to the
the following cautions. products. Self-tapping screws are not recommended. When
Cautions for Storage using self-tapping screws, the screw may enter the hole
• Ensure that storage conditions comply with the standard diagonally, not vertically, depending on the conditions of hole

ns
temperature (5°C to 35°C) and the standard relative before threading or the work situation. That may stress the
humidity (around 40% to 75%); avoid storage locations products and may cause failures.

ig
that experience extreme changes in temperature or • Recommended screw torque: 0.588 to 0.785 N●m (6 to 8
humidity. kgf●cm).

es
• Avoid locations where dust or harmful gases are present • For tightening screws, if a tightening tool (such as a driver)

D
and avoid direct sunlight. hits the products, the package may crack, and internal
• Reinspect for rust on leads and solderability of the stress fractures may occur, which shorten the lifetime of

ew
products that have been stored for a long time. the electrical elements and can cause catastrophic failure.
Cautions for Testing and Handling Tightening with an air driver makes a substantial impact.
When tests are carried out during inspection testing and In addition, a screw torque higher than the set torque can
other standard test periods, protect the products from
power surges from the testing device, shorts between
the product pins, and wrong connections. Ensure all test
rN
be applied and the package may be damaged. Therefore, an
electric driver is recommended.
When the package is tightened at two or more places, first
fo
parameters are within the ratings specified by Sanken for pre-tighten with a lower torque at all places, then tighten
the products. with the specified torque. When using a power driver, torque
d

Remarks About Using Silicone Grease with a Heatsink control is mandatory.

de

• When silicone grease is used in mounting the products on Soldering

a heatsink, it shall be applied evenly and thinly. If more • When soldering the products, please be sure to minimize
en

silicone grease than required is applied, it may produce the working time, within the following limits:
excess stress. 260±5°C 10±1 s (Flow, 2 times)
• Volatile-type silicone greases may crack after long periods 380±10°C 5±0.5 s (Soldering iron, 1 time)
m

of time, resulting in reduced heat radiation effect. Silicone • Soldering should be at a distance of at least 1.5 mm from
m

greases with low consistency (hard grease) may cause the body of the products.
cracks in the mold resin when screwing the products to a Electrostatic Discharge
o

heatsink. • When handling the products, the operator must be

ec

Our recommended silicone greases for heat radiation grounded. Grounded wrist straps worn should have at
purposes, which will not cause any adverse effect on the least 1 MΩ of resistance from the operator to ground to
R

product life, are indicated below: prevent shock hazard, and it should be placed near the
operator.
ot

Type Suppliers • Workbenches where the products are handled should be

G746 Shin-Etsu Chemical Co., Ltd. grounded and be provided with conductive table and floor
N

YG6260 Momentive Performance Materials Inc. mats.

SC102 Dow Corning Toray Co., Ltd. • When using measuring equipment such as a curve tracer,
the equipment should be grounded.
Cautions for Mounting to a Heatsink • When soldering the products, the head of soldering irons
• When the flatness around the screw hole is insufficient, such or the solder bath must be grounded in order to prevent
as when mounting the products to a heatsink that has an leak voltages generated by them from being applied to the
extruded (burred) screw hole, the products can be damaged, products.
even with a lower than recommended screw torque. For • The products should always be stored and transported in
mounting the products, the mounting surface flatness should Sanken shipping containers or conductive containers, or
be 0.05 mm or less. be wrapped in aluminum foil.

28610.09, Rev. 6 17
SANKEN ELECTRIC CO., LTD.
SLA6868MZ and
SLA6870MZ High Voltage 3-Phase Motor Drivers

ns
ig
es
D
• The contents in this document are subject to changes, for improvement and other purposes, without notice. Make sure that this is the
latest revision of the document before use.

ew
• Application and operation examples described in this document are quoted for the sole purpose of reference for the use of the prod-
ucts herein and Sanken can assume no responsibility for any infringement of industrial property rights, intellectual property rights or
any other rights of Sanken or any third party which may result from its use.
rN
• Although Sanken undertakes to enhance the quality and reliability of its products, the occurrence of failure and defect of semicon-
ductor products at a certain rate is inevitable. Users of Sanken products are requested to take, at their own risk, preventative measures
fo
including safety design of the equipment or systems against any possible injury, death, fires or damages to the society due to device
failure or malfunction.
d

• Sanken products listed in this document are designed and intended for the use as components in general purpose electronic equip-
de

ment or apparatus (home appliances, office equipment, telecommunication equipment, measuring equipment, etc.).
When considering the use of Sanken products in the applications where higher reliability is required (transportation equipment and
en

its control systems, traffic signal control systems or equipment, fire/crime alarm systems, various safety devices, etc.), and whenever
long life expectancy is required even in general purpose electronic equipment or apparatus, please contact your nearest Sanken sales
m

representative to discuss, prior to the use of the products herein.

The use of Sanken products without the written consent of Sanken in the applications where extremely high reliability is required
m

(aerospace equipment, nuclear power control systems, life support systems, etc.) is strictly prohibited.
o

• In the case that you use Sanken products or design your products by using Sanken products, the reliability largely depends on the
ec

degree of derating to be made to the rated values. Derating may be interpreted as a case that an operation range is set by derating the
load from each rated value or surge voltage or noise is considered for derating in order to assure or improve the reliability. In general,
R

derating factors include electric stresses such as electric voltage, electric current, electric power etc., environmental stresses such
as ambient temperature, humidity etc. and thermal stress caused due to self-heating of semiconductor products. For these stresses,
ot

instantaneous values, maximum values and minimum values must be taken into consideration.
In addition, it should be noted that since power devices or IC's including power devices have large self-heating value, the degree of
N

derating of junction temperature affects the reliability significantly.

• When using the products specified herein by either (i) combining other products or materials therewith or (ii) physically, chemically
or otherwise processing or treating the products, please duly consider all possible risks that may result from all such uses in advance
and proceed therewith at your own responsibility.
• Anti radioactive ray design is not considered for the products listed herein.
• Sanken assumes no responsibility for any troubles, such as dropping products caused during transportation out of Sanken's distribu-
tion network.
• The contents in this document must not be transcribed or copied without Sanken's written consent.

28610.09, Rev. 6 18
SANKEN ELECTRIC CO., LTD.