10/30/23, 12:06 PM Concrete Mix Design Using DoE Method
Disclaimer: This is an example of a student written essay.
Click here for sample essays written by our professional writers.
View full disclaimer
/ Essays / Engineering
Share this: Facebook Twitter Reddit LinkedIn WhatsApp
Concrete Mix Design Using DoE Method
[Author]
Click or tap here to enter text.
Click or tap here to enter text.
Click or tap here to enter text.
Contents Page
1. Introduction
2. Design Requirements and Assumptions
3. Mean Compressive Strength
4. Water / Cement Ratio
5. Water Content
6. Cement Content
7. Density of Concrete
8. Aggregate Content
9. Fine aggregate content
10. Coarse Aggregate Content
11. Summary
References
1. Introduction
1.1. In this report I will calculate the exact amount of materials required to produce
1m3 of concrete, designed to the Department of Environment (DoE) method. This method of
concrete design was first introduced in 1950, under the name “Road Note No 4”, which was later
replaced by “Design of Normal Concrete Mixes” in 1975 by the British Department of Environment
(DoE). The design guidance was updated in 1988 to account for changes in the then current British
Standards and is still used today, often being referred to as the British Standard concrete mix design.
1.2. The DoE method for concrete mix design works by calculating the values of 8
fundamental processes:
1. Mean target compressive strength
2. Water/Cement ratio
3. Water content using required slump value and aggregate size
4. Cement content
5. Concrete density
6. Aggregate content
https://www.ukessays.com/essays/engineering/concrete-mix-design-using-doe-method.php#_Toc534298782 1/7
10/30/23, 12:06 PM Concrete Mix Design Using DoE Method
7. Proportion of fine & course aggregate
8. Course aggregate
2. Design Requirements and Assumptions
2.1. Below is a list of design requirements/assumptions that have been used for the
concrete mix design:
- A slump of 10mm to 30mm.
- A characteristic 28-day compressive strength of 30 N/mm2 (5% failures permitted).
- The standard deviation of the tests is σ = 6.1 N/mm2.
- Ordinary Portland cement (42.5 N).
- Crushed sand of 2.7 density and 60% passing through a 600 µm sieve.
- Crushed coarse aggregate 2.6 density and 20mm are used.
3.
Mean Compressive Strength
3.1. The target mean compressive strength ( 𝑓𝑚 )
can be calculated by:
characteristic strength ( 𝑓𝑐 ) + ( risk factor 𝑘 x standard deviation ( 𝜎 ) )
Table 1. Risk factor values used in statistical control (G.D.Taylor, 2000)
Percentage failure permitted Risk factor value
16 1.00
10 1.28
5 1.64
2.5 1.96
2 2.05
1 2.33
𝑓𝑚 = 𝑓𝑐 + ( 1 . 64 x σ )
𝑓𝑚 = 30 + 1 . 64 x 8 = 40𝑁 / mm2
4. Water / Cement Ratio
4.1. The water / cement ratio is determined by using data from table 2.
Table 2. Approximate compressive strength of concrete made with a free Water/Cement
ratio of 0.50 (G.D.Taylor, 2000)
https://www.ukessays.com/essays/engineering/concrete-mix-design-using-doe-method.php#_Toc534298782 2/7
10/30/23, 12:06 PM Concrete Mix Design Using DoE Method
Type of cement Type of coarse Compressive Strength
aggregate (N/mm2)
Age (days)
3 7 28 91
Ordinary Portland Cement Uncrushed 22 30 42 49
(OPC)
Or
Sulphate-resisting Portland Crushed 27 36 49 56
(SRPC)
Rapid-hardening Portland Uncrushed 29 37 48 54
(RHPC)
Crushed 34 43 55 61
1 N/mm2 = 1 MN/m2 = 1 MPa
4.2. One of the requirements of the design mix stated that the mix will use ordinary
Portland cement, with crushed aggregate, therefore, the 28-day strength value of 49 N/mm2 from
the above table can be used to calculate the water / cement ratio:
1. 0.5 is used for the free-water/cement axis as this value is used in table 2.
2. At the point of intersection of compressive strength value of 49 N/mm2 with the free-water /
cement value 0.5 (orange), the nearest curve is offset parallel to the point of intersection (blue).
3. A horizontal line is drawn starting at the desired compressive strength of 40 N/mm2, until it
intersects with the parallel curve, with a vertical line drawn from this point of intersection to
find the desired free-water / cement ratio of 0.57 (red).
UKESSAYS.COM Search
THE ESSAY WRITING EXPERTS GBR Offers Support Alerts Sign In
UK Essays Services Samples Reviews About Us Resources Humanity University Place an Order
https://www.ukessays.com/essays/engineering/concrete-mix-design-using-doe-method.php#_Toc534298782 3/7
10/30/23, 12:06 PM Concrete Mix Design Using DoE Method
Figure 1. Desired free-water / cement ratio (G.D.Taylor, 2000)
5. Water Content
5.1. To calculate the required water content to achieve a suitable concrete
workability, the following factors are used:
- Slump value (10 mm – 30 mm)
- Aggregate size (20 mm)
The values of these factors have been provided in the design requirements and can be found in table
3.
5.2. Using the information provided in Table 3 (below), we can determine that the
required water content is 190 kg/m3by intersecting the value at 20 mm aggregate size and 10 mm –
30 mm slump value for crushed aggregate.
Table 3: Workability and approximate free-water content (G.D.Taylor, 2000)
Slump (mm) Very Low Medium High
Low
10 – 30 – 60 60 –
0 – 10 30 180
Vebe (seconds) 3–6
>12 6 – 12 0–3
1. Water Content
Maximum size of aggregate Type of Water content (kg/m3)
(mm) aggregate
10 Uncrushed 150 280 205 225
Crushed 180 205 230 250
https://www.ukessays.com/essays/engineering/concrete-mix-design-using-doe-method.php#_Toc534298782 4/7
10/30/23, 12:06 PM Concrete Mix Design Using DoE Method
20 Uncrushed 135 160 180 195
Crushed 170 190 210 225
40 Uncrushed 115 140 160 175
Crushed 155 175 190 205
2. Reduction in water content when fly ash is used
Percentage of fly ash in cementitious material Reduction in water content (kg/m3)
10 5 5 5 10
20 10 10 10 15
30 15 15 20 20
40 20 20 25 25
50 25 25 30 30
6. Cement Content
6.1. To calculate the amount of cement required, the following formula is used
water content per 𝑚3
Cement content per 𝑚3 =
free – water / cement ratio
The values for both water content and free-water / cement ratio are known, so it is easily calculated.
190
Cement content per 𝑚3 = 0 . 57
= 333 kg / 𝑚3
7. Density of Concrete
7.1. The DoE method uses a graphical system for calculating the density of the fresh
concrete, using the relative aggregate density and free-water content.
7.2. The relative aggregate density has been provided at 2.6, and the free-water
content is 190 kg/m , therefore the density can be calculated to be 2370 kg/m3, as shown in figure
3
2.
Figure 2. Fresh Concrete Density (G.D.Taylor, 2000)
https://www.ukessays.com/essays/engineering/concrete-mix-design-using-doe-method.php#_Toc534298782 5/7
10/30/23, 12:06 PM Concrete Mix Design Using DoE Method
8. Aggregate Content
8.1. Using the fresh concrete density of 2370 kg/m3, and the aggregate content can
be calculated using the following formula:
Aggregate content = fresh density – ( cement content + water content )
These values have already been calculated, therefore:
Aggregate content = 2370 – 333 + 190Aggregate content = 1847 kg / 𝑚3
9. Fine aggregate content
9.1. The proportion of fine aggregate in the concrete mix will depend on:
- The grading of the sand
- Maximum aggregate size
- Workability of the concrete
- Free-water / cement ratio
9.2. Figure 3 (below) shows the graphical method of calculating the proportion of
fine aggregate, which gives a result of 30% by starting at 0.5 free-water/cement ratio and drawing a
line vertically upwards to the percentage of fine aggregate passing through a 600 µm sieve (60%). A
horizontal line is then drawn to find the proportion of fine aggregate.
Figure 3. Recommended proportions of sand according to percentage passing a 600 µm sieve
(G.D.Taylor, 2000)
Using the total aggregate content 1847 kg/m3, the proportion of fine aggregate can be calculated.
1847 x 0 . 3 = 554 kg / 𝑚3
10. Coarse Aggregate Content
10.1. Once the fine aggregate content has been calculated, we can simply deduct this
value from the total aggregate content to determine the amount of coarse aggregate required.
1847 – 554 = 1293 kg / 𝑚3
11. Summary
11.1. From the calculations above, it can be determined that for each m3 of concrete,
the correct amounts for each component are as follows:
https://www.ukessays.com/essays/engineering/concrete-mix-design-using-doe-method.php#_Toc534298782 6/7
10/30/23, 12:06 PM Concrete Mix Design Using DoE Method
Table 4. Quantity of materials required to produce 1m3 of concrete with a 28-day compressive strength
of 30 N/mm2, designed to the DoE method.
Material Quantity (kg/m3)
Cement 333
Water 190
Fine Aggregate 554
Coarse Aggregate 1293
References
G.D.Taylor, 2000. Materials in Construction – An Introduction. 3rd ed. Essex: Pearson Education
Limited.
Share this: Facebook Twitter Reddit LinkedIn WhatsApp
/ Essays / Engineering
https://www.ukessays.com/essays/engineering/concrete-mix-design-using-doe-method.php#_Toc534298782 7/7
