Realand Bio Co., LTD.

Fingerprint Access Control Product

Hardware User Manual M-F211
Date: January 2014
 Fingerprint Access Control Hardware Manual (M-F211)
CONTENT
CHAPTER 1 NOTICE FOR USING ......................... - 5 -
1.1 OPERATING ENVIRONMENT ................................... - 6 -
1.2 NOTE FOR INSTALLATION ....................................... - 6 -
1.3 WIRING - BRIEF DESCRIPTION ............................... - 10 -
1.4 INTERFACE DESCRIPTION ..................................... - 15 -
CHAPTER 2 QUICK REFERENCE ....................... - 18 -
2.1 KEY BUTTON: ................................................ - 19 -
2.2 DESCRIPTION OF PRESSING FINGERPRINT . - 20 -
2.3 MENU............................................................ - 22 -
2.4 BASIC OPERATION........................................ - 26 -
CHAPTER 3 USER MANAGEMENT .................... - 34 -
3.1 ENROLL USER .............................................. - 35 -
3.2 USER AUTHENTICATION ..................................... - 45 -
CHAPTER 4 LOG DATA ........................................ - 46 -
4.1. VIEW LOG (LOG QUERY).............................. - 46 -
 Fingerprint Access Control Hardware Manual (M-F211)
4.2. LOG SETUP .................................................. - 50 -
4.3. MESSENGER................................................. - 53 -
4.4. LOG INFO. ..................................................... - 56 -
4.5. TSEGMENT (CLOCK IN/CLOCK OUT STATUS ON
HOMEPAGE) ............................................................... - 57 -

CHAPTER 5 U-DISK .............................................. - 60 -

5.1. DOWNLOAD .................................................. - 60 -
5.2. UPLOAD ........................................................ - 63 -
5.3. DOWNLOAD / UPLOAD THE DATA BY THE
ATTENDANCE MANAGEMENT SOFTWARE .................. - 65 -
CHAPTER 6 SETTING ........................................... - 66 -
6.1. SYSTEM ........................................................ - 66 -
6.2. COMMUNICATION SETTINGS ........................ - 77 -
6.3. SENSOR ........................................................ - 83 -
6.4. ALARM .......................................................... - 85 -
6.5 POWER................................................................... - 87 -
6.6 S-TEST ................................................................... - 92 -
 Fingerprint Access Control Hardware Manual (M-F211)
CHAPTER 7 ACS ................................................... - 95 -
7.1. D-LOCK (DOOR LOCK) .............................. - 96 -
7.2. USER CONTROL .......................................... - 103 -
7.3. HIJACK ........................................................ - 104 -
7.4. PSEGMENT ................................................. - 106 -
7.5. PASS GROUP .............................................. - 108 -
CHAPTER 8 DEVICE INFORMATION .................- 115 -
CHAPTER 9 FAQ ..................................................- 117 -
1. HOW TO REMOVE THE ADMIN PRIVILEGE ON THE
DEVICE MENU? ........................................................ - 117 -
 W E COULD REMOVE THE PRIVILEGE THROUGH
THE SOFTWARE (METHOD 1) .................................. - 117 -
 W E CAN ALSO REMOVE THE ADMIN PRIVILEGE BY
PRESSING A KEY ON THE MAINBOARD. (METHOD 2)- 119 -
 Fingerprint Door Opener

Chapter 1 Notice for using

Thanks for purchasing our Fingerprint Time Attendance Terminal.

Please refer to this user manual carefully before using, which
helps you improve the efficiency of using this product.

 Please ensure what version of the device you have, before

you go through this installation manual:

A. Standard version: 500 fingerprint capacity，no record, no

communication.
B. With record version: 800 fingerprint capacity, 30,000record,
RS485 communication.
C. Network version: 800 fingerprint capacity, 50,000 record,
RS485, TCP/IP communication, USB flash drive function.

- 5 - 【Chapter 1 Notice for using】

 Fingerprint Door Opener
1.1 Operating environment

 Avoid installing the Access Control Device at places where

irradiated by strong light directly. The strong light affects the
collecting of fingerprints which would lead to the failure of
the fingerprint authentication.
 The operating temperature of Access Control Device is 0℃ –
60℃ . Avoid the long term outdoor usage of the terminal.
The normal working of the Access Control Device will be
affected by the long term outdoor usage. If it is necessary to
use outdoor, the sunshade and cooling equipment are
recommended in summer and warm keeping facility is
recommended in winter to protect the Access Control
Device.
1.2 Note for Installation

Please go through the installation manual before the install the

- 6 - 【Chapter 1 Notice for using】

 Fingerprint Door Opener

device. The correct installation method will lead you finish the
successful installation in a short time. If install in a incorrect way,
it will damage the device.

1． Make sure your power supply is on “OFF” status. Else it may

damage the device or the core part of the device if you turn
on the power during the installation.

2． For all the connection cable, the core should not be exposed
for longer than 5MM. It’s better to use the insulating tape on
the connection area, and use different color cable to
differentiate the cables. Refer to the following picture:

- 7 - 【Chapter 1 Notice for using】

 Fingerprint Door Opener

3． When installing in electrostatic environment or dry weather,

Please connect the GND cable first to avoid the device
damage from excessive static electricity.

4． Please connect the power cable after connecting all other

cables. When you found that the device cannot work
normally, please cut off the power and check all the
connection. Note: all wiring operation with live may lead to
damage the device. Warranty does not apply under this
damage.

- 8 - 【Chapter 1 Notice for using】

 Fingerprint Door Opener

5． It’s recommended to install the device on height of 1.4 –

1.5Meter.

6． Please make sure someone is outside the door during you

testing the door opening function to avoid any accident that
you cannot open the door.

7． It’s recommended to use the 12V/2A power supply for this

access control device. PS: it’s recommended to use the
2A/12V DC door lock. If the electric lock spec is lower than
this spec, please consult the engineer. If the power supply
does not meet the above requirement, the lock may not be
active normally.

8． Please strictly follow the “installation manual” to install the

device. Otherwise, any device damage coz the incorrect
wiring is not under the warranty.

- 9 - 【Chapter 1 Notice for using】

 Fingerprint Door Opener
9. If the power supply is far from the device, please do not use
the Ethernet Cable to connect the power supply and the device.
During installation, please do not install the power supply far
from the access control device, otherwise, the long transmission
distance might cause the voltage attenuation.

10. (Optional) when use the RS485 connection, please use the
professional 485 communication cable and the active converter
RS485 with bus structure wiring. When the RS485 transmission
distance is longer than 100 meter, need to add a matching
resistance at the beginning terminal and the end terminal of the
RS485 Bus. (R is around 120Ω.)

11. Please refer to the installation manual for more details.

1.3 Wiring - brief description
Access Control Device (Door Opener), is with user-friendly

- 10 -【Chapter 1 Notice for using】

 Fingerprint Door Opener
design. Such as: Tamper function ( disable to turn off the
device when the it is being removed un-authorized), Cancel
alarm function (When being removed un-authorized, and
install again, the Tamper alarm still cannot be turn off, need
to turn off the alarm by the “Cancel Tamper Alarm, fire
detection (with fire warning sensor interface), open the door
timeout detection, forced open the door detection.

We should install the Access Control Device correctly to use

its powerful function. Here is the access control device
interface:

- 11 -【Chapter 1 Notice for using】

 Fingerprint Door Opener

- 12 -【Chapter 1 Notice for using】

 Fingerprint Door Opener

Lock connection diagram:

- 13 -【Chapter 1 Notice for using】

 Fingerprint Door Opener

- 14 -【Chapter 1 Notice for using】

 Fingerprint Door Opener

1.4 Interface Description

 J7 interface
1. WGIN0 & WGIN1: Wiegand communication input,
can connect to the Wiegand Controller, such as the

- 15 -【Chapter 1 Notice for using】

 Fingerprint Door Opener
Wiegand reader.
2. GND & 12V: power supply. It can supply power to the
Wiegand Controller.
3. WGOUT0 & WGOUT1: Wiegand communication
output. Devices can communicate with the Wiegand
protocol terminal.
4. 485 A & 485B: 485 communication interface, can
connect to 485 converters and then communicate with
the computer.
5. GND & FC_CANCLE: Cancel Tamper Switch, can
connect to the single-pole, single-throw switch.
 J6 interface
1. 12 V & GND: power input (supply power to the
Access Control Device).
2. GND & OPK: connect to the Door Release Button
(Exit Button).
3. GND & SEN: magnetic door contact input.
4. NO, COM, NC: door lock connection, with Normally
Open, Normally Closed connection.

- 16 -【Chapter 1 Notice for using】

 Fingerprint Door Opener
(Please refer to the Lock-Connection diagram on 1.3
Wiring – brief description)
5. ALMI & ALMO: alarm input and output, connect to
the Alarm Siren.
6. B + & B-: doorbell interface, connect to the doorbell,
to inform person inside there’s the visitor outside the
door.
7. GND & CTL: Fire warning sensor input.

- 17 -【Chapter 1 Notice for using】

 Fingerprint Door Opener

Chapter 2 Quick Reference

Picture 1 Access Control Device (Door Opener)

- 18 -【Chapter 2 Quick Reference】

 Fingerprint Door Opener

2.1 Key button:

Keypad Description:

- 19 -【Chapter 2 Quick Reference】

 Fingerprint Door Opener

 POW turn on / turn off device

 ESC Exit or cancel when in Menu
 MENU Enter to MENU (keep long
pressing to enter the MENU)
 OK Confirm option
 ▲ Page up
 ▼ Page down
  Doorbell button

Picture2

2.2 Description of Pressing Fingerprint

Correct pressing method: Press with your finger right on the

- 20 -【Chapter 2 Quick Reference】

 Fingerprint Door Opener
fingerprint collecting window, with the fingerprint’s centre
aligning to the center of the gathering window as much as possible.
Finger pressing method is shown as follows:

Correct

Too perpendicular Too deflective

- 21 -【Chapter 2 Quick Reference】

 Fingerprint Door Opener

Tilting Too low

2.3 Menu
Note:
1) When the device is in homepage, keep pressing
the [MENU] button for 1 second to enter the
main MENU.
2) Press the UP arrow and Down arrow to select the
item you need.
3) OK key is together with the MENU.

- 22 -【Chapter 2 Quick Reference】

 Fingerprint Door Opener
[Main menu]
Include 6 items:
1.User; 2.LogData, 3.U-Disk, 4.Setting, 5.ACS, 6.About. as
the following:

 1. User
Two submenus in the 【User】window: 【1.Enroll】 and
【2.Delete】. you can enroll the fingerprint and RFID
card to the employee. And you can set the admin to
- 23 -【Chapter 2 Quick Reference】
 Fingerprint Door Opener
allow whom could enter the device MENU.

 2.LogData

In the main window of the MENU, select 【LogData】 to

enter the LogData management window.
There’re some submenus in the 【LogData】window:
【ViewLog】, 【LogSetup】, 【Message】, 【LogInfo】,
【 tSegment】.
Note: the 【message】function not for all the series
models. If you can’t find it in your menu, that means no
【message】for your model.

 3.U-Disk

In the main window of the MENU, select 【U-Disk】to

enter the U-Disk management window.
There’re two submenus in 【 U-Disk 】 window:

- 24 -【Chapter 2 Quick Reference】

 Fingerprint Door Opener
【Download】,【Upload】.

 4.Setting

In the main window of the MENU, select 【Setting】to

enter the settings management window.
There’re six submenus in 【Setting】window:【System】,
【Comm.】 , 【Sensor】, 【Alarm】, 【Power】, 【S-Test】.
 5.ACS
In the main window of the MENU, select 【ACS】to
enter the Access Control Setting window.
There’re six submenus in 【ACS】window:【D-Lock】,
【UserCtrl.】, 【Jijack】, 【PSegment】, 【PGroup】,
【PZone】.
 6.About
In the main window of the MENU, select 【About】to

- 25 -【Chapter 2 Quick Reference】

 Fingerprint Door Opener
enter the System info window. You could check the
device system info in 【About】window.

2.4 Basic Operation

 Power on
Connect Device to the Power Supply, pressing the 【POW/ESC】
button to turn on the device. (It’s defaulted to auto power on
when connect to the power supply.)

Note: The power for the Access Control Device must

be the DC 12V.

 Enter Menu
Keep Long pressing the [MENU / OK] button for 1 second
to enter the main menu, and select the item you need.

Note: If you’ve registered managers, you need to get

through the admin verify before enter the MENU. If the
admin have left the company or you don’t remember what
you admin you set to the device, you could connect the

- 26 -【Chapter 2 Quick Reference】

 Fingerprint Door Opener
Software to the Device to cancel the privilege.
 User Management

User
Manangerment

Enroll Delete

Fingerprint Card Fingerpint+Card

Picture 2 Sub-menu of User

Operation: Press the ▲,  keys to select the item you need
 press the [MENU / OK] key to enter the selected menu.
Select [Enroll] or [Delete] to enroll or delete fingerprint,
proximity card.
in the sub-menu [Enroll], we can set the User ID, Name,
Role(privilege), Note to the employee  select to enroll the

- 27 -【Chapter 2 Quick Reference】

 Fingerprint Door Opener
Fingerprint, Card, FP+Card.
Note:
1) Name and Note contents could be uploaded by the
Software. This Device doesn’t have the keypad to
enter the words.
2) User ID, you can only use the ▲,  keys to set the
number, there’s no keypad for you to enter the
number.
【Delete】is to delete the employee enroll info on the
device.
Please refer to Chapter 3 for more info.

 LogData
Operation: Press the ▲,  keys to select the item you need
 press the [MENU / OK] key to enter the selected menu.

- 28 -【Chapter 2 Quick Reference】

 Fingerprint Door Opener

Log
managem
ent

ViewLog LogSetup Message LogInfo TSegment

Picture 3 sub-menu of LogData

【View Log 】You can query access or manage log By
entering the User ID or fingerprint verification.
【Log Setup】Can set log Warnings, the number of warnings
access, re-verify time and delete logs.
【Message】can set 10 groups notice message. This could
be uploaded by the software.
【Log Info】can check the logs in the device.
【 TSegment 】 Can set 24 different duty time for the
attendance, such as: 08:00-12: 00 (Duty On); 13:00-17:00
(Duty Off)

- 29 -【Chapter 2 Quick Reference】

 Fingerprint Door Opener
 U disk management
Operation: Press the ▲,  keys to select the item you need
 press the [MENU / OK] key to enter the selected menu.

U-Disk

Downlo Upload
ad data
Person Firmwa
Upload
All nel re
Setting
New Histori New Enroll Enroll upgrad
s
GLog c GLog SLog Info info. e
Up..

Picture 4 sub-menu of U-Disk

【Download】can download the New GLog, Historic GLog,
New Slog, Historic Slog, All Enroll Info Down.., Personnel
Enroll info from the device.
【Upload】can upload the All Enroll Info Up.., Personnel
Enroll info., Upload settings, Firmware Upgrade to the
device.

- 30 -【Chapter 2 Quick Reference】

 Fingerprint Door Opener
[Upload] can upload personal data / full registration data,
sound files, configuration files, the firmware upgrade.

 Setting
Operation: Press the ▲,  keys to select the item you need
 press the [MENU / OK] key to enter the selected menu.

Setting

Commun
System Sensor Alarm Power S-Test
ication

Picture 5 sub-menu of Setting

【System】Can set the Device MENU display language,
UI-theme, Date&Time format, Volume, User ID length, verify
mode etc. Please refer to Chapter 6 for more info.
【Com.】 can set the Device ID, TCP/IP address, TCP/IP
port, RS485 comm parameter.
【Sensor】can adjust the sensor detection.

- 31 -【Chapter 2 Quick Reference】

 Fingerprint Door Opener
【Alarm】Can set 24 Groups timing bell.
【Power】Can set to Auto return time, Power off time, Auto
off, Standby time, Alarm in standby, Auto power on, Enable
shutdown.
【S-Test】can check the sensor detection, RFID card, LCD
display, Voice out, Keypad works well or not.
 ACS (Access Control Settings)
Operation: Press the ▲,  keys to select the item you need
 press the [MENU / OK] key to enter the selected menu.

ACS

PSegmen
D-Lock UserCtrl Hijack PGroup PZone
t

Picture 6 sub-menu of ACS

【D-Lock】door lock settings.
【user control】user-specific settings.

- 32 -【Chapter 2 Quick Reference】

 Fingerprint Door Opener
【Hijack】settings for the hijack.
【PSegment】duty time for pass through.
【PGroup】Group time for pass through
【PZone】Zone time for pass through.

 About (System info.)

Picture 7 Hardware system info

- 33 -【Chapter 2 Quick Reference】

 Fingerprint Door Opener

Chapter 3 User Management

When device in homepage window, keep long pressing the
【MENU/OK】for 1 second to enter the device MENU (if you’ve
set the admin to the device, need get through the admin
verify first.):

Picture 8 main menu

Operation: Press the ▲,  keys to select the item you need
 press the [MENU / OK] key to enter the selected menu.

- 34 -【Chapter 3 User Management】

 Fingerprint Door Opener

.
Picture 9 User Management
3.1 Enroll User

3 verify mode for the Access Control Device: Fingerprint,

RFID Card, Fingeprint+RFID card.

Every employee can enroll one User ID only. This User ID is

the unique mark for different employee The User ID on the
Device and Software, must be in corresponding.

- 35 -【Chapter 3 User Management】

 Fingerprint Door Opener
 Fingerprint Enroll
puch 3
User Finger times
User Enroll for the ESC
ID print same
finger

Picture 10 Enroll Fingerprint

Refer to the following details:
1).enter the User window.
2).select the enroll way

- 36 -【Chapter 3 User Management】

 Fingerprint Door Opener
Picture 11 User Enroll
3).set the User ID, Role, on the User enroll window. (name
and note content need to finish on the software and upload
to the device). Press 【MENU/OK】to finish the User ID setting,
press  to select the role, long press【MENU/OK】to enter the
setting window. Press ▲, to select the role, press
【MENU/OK】 to finish the setting.

Picture 12 User Enroll

- 37 -【Chapter 3 User Management】

 Fingerprint Door Opener
4). Select the verify type: Fingerprint, RFID card,
Fingerprint+RFID. (No Password verify on this Access
Control Device.)

Picture 13 choose the verify mode

5). Select to enroll the fingerprint, open the Fingerprint
enrollment window  press the same finger on the sensor
for 3 times. After the device give the “Beep Beep Beep”
sound, the device will auto save the enroll info. Enroll card
user.

- 38 -【Chapter 3 User Management】

 Fingerprint Door Opener

Picture 14 Fingerprint enroll

if you need to enroll more fingerprint for this user, press

nd rd
【MENU/OK】to enroll the 2 , 3 , .. fingerprint for this user.
Same operation in above.

 RFID card Enroll

Steps 1 – steps 4 same as the previous “Fingerprint enroll”.

- 39 -【Chapter 3 User Management】

 Fingerprint Door Opener

Picture 15 Card enroll

Step 5: enter the Card enroll window, put the RFID card in
the RFID card inductive area.
After enrollment, the LCD shows the RFID card NO. and
there’s a “Beep Beep Beep” sound from the device. And it
will save the enrollment info automatically.

- 40 -【Chapter 3 User Management】

 Fingerprint Door Opener

Picture 16 RFID card enroll

notice：
 If you don't enroll any admin to the device, so anybody
could enter the device MENU to change the settings. If
you’ve enroll the admin to the device, you could enter the
MENU only after get through the admin verification.
 [Manager] has the highest authority, you can operate
all functions of the device MENU.

- 41 -【Chapter 3 User Management】

 Fingerprint Door Opener
 【log Query】can only enter the MENU – LogData
menu (including check the attendance logs and delete the
attendance logs) and [Device Information].
 【Registrar】 can only enter the MENU – User to enroll
new user and delete the user info.

 FP+CARD
Select “FP+Card” to enter the FP + Card enroll window:
The first 4 steps are same as the Fingerprint enroll.

- 42 -【Chapter 3 User Management】

 Fingerprint Door Opener

Picture 17 FP+Card enroll

Step 5: enter the FP+Card enroll menu: first enroll the
fingerprint to the employee, after the “Beep Beep Beep”
sound, the device will auto save the enrollment. Then, press
【POW/ESC】, and put the Card on the inductive area, after
device read the Card NO., there would be a “Beep Beep
Beep” sound, and device auto save the enrollment.

- 43 -【Chapter 3 User Management】

 Fingerprint Door Opener
 Delete enroll
Tips: the Access Control Device has the max capacity for the
fingerprint enrollment. When it comes to the max, there’s a
warning from the device.
When the employee resign, please delete his/her enroll info.

select
User Delete User ID item to ESC
delete

Picture 18 Delete enroll

Picture 19 Delete enroll

- 44 -【Chapter 3 User Management】

 Fingerprint Door Opener
Get the User ID you need to delete by “verification” or use
the key ▲,  , click the 【MENU/OK】【MENU/OK】to confirm
the delete.
3.2 User Authentication
 Fingerprint verify
Verify the fingerprint in 1:N mode, Press the finger on the
sensor directly and correctly.
When verify successfully, devices voice prompt “Thank you”.
And display “Verify OK” on LCD. If failed, it prompts “Press
again”.
 Card verify
Punch card on the Card induction area.
When verify successfully, devices voice prompt “Thank you”.
And display “Verify OK” on LCD. If failed, it prompts “Invalid
card”.

- 45 -【Chapter 3 User Management】

 Fingerprint Door Opener

Chapter 4 Log Data

When device in homepage window, keep long pressing the
【MENU/OK】for 1 second to enter the device MENU (if you’ve
set the admin to the device, need get through the admin
verify first.),  【LogData】:

Picture 20 Log Data

4.1. View Log (Log Query)

- 46 -【Chapter 4 Log Data】

 Fingerprint Door Opener

MENU Log Data View Log

Picture 21 View Log

Figure 21 Check Log

 View GLog (check attendance logs)

- 47 -【Chapter 4 Log Data】

 Fingerprint Door Opener
select【View GLog】 press【MENU/OK】  Enter the User
ID enter window (press ▲, to select “View GLog” or
View SLog)  press 【MENU/OK】to confirm.

Picture 23 View GLog

Slog: is the records of people that enter the MENU

and record of the MENU operation. Each time, the admin
enter the MENU, and change the settings, it will keep a

- 48 -【Chapter 4 Log Data】

 Fingerprint Door Opener
record of this operation.

Form 1 Description for the Slog

Item Description Item Description

V-F Fingerprint verify OI Over time IN

V-C RFID card verify OO Over time OUT

V-FC FP+ RFID CARD O OUT

AA Duress verify I BACK

N Attend U1 Definition 1

CI Clock In U2 Definition 2

CO Clock Out

Form 2 Description for GLog

Item Description Item Description

E_U Enroll user D_SL Delete admin log

- 49 -【Chapter 4 Log Data】

 Fingerprint Door Opener
E_SM Enroll super admin. D_EL Delete all enroll

E_EM Enroll registrar S_S System setting

E_VM Enroll log query S_T Time setting

E_DF Delete fingerprint S_L Log setting

E_DC Delete card S_C Comm.setting

D_GL Delete Glog

4.2. Log Setup

menu Log Data Log Setup

Picture 24 Log Set Up

- 50 -【Chapter 4 Log Data】

 Fingerprint Door Opener

Picture 25 Log setting interface

 Slog wrn (admin. Log warning)
Admin log capacity is 1000, when it rest 100, and admin
enter the MENU, device will prompt “Slog overflow”. The
Slog Wrn is defaulted to “100”, we can press 【MENU/OK】to
change it.
 Glog wrn (attendance log warning)

- 51 -【Chapter 4 Log Data】

 Fingerprint Door Opener
Attendance record capacity is 50,000. When it rest 1000,
and employee verify, it will prompt “GLog overflow”. The
“GLog wrn” is defaulted to “1000”. We can press 【MENU/OK】
to change it.

 RE-verify (min.): interval time of attendance for same

User ID
It’s interval time for the same User ID to take the attendance.
It’s defaulted to 3mins. Max is 255mins. If we set it to 3mins,
that means we cannot take the attendance more than 1 time
in 3 mins.

For example: Amaris, ID=001, we set the re-verify time to

5mins. And she put her finger on sensor for attendance at
9:00:15, and she put finger again at 9:04:30, the device will
save the record of 9:00:15 only. When she put finger at
9:04:30, the LCD display “Already in”, and not save this
record. But the device will still open the door.
 GLog Delete

- 52 -【Chapter 4 Log Data】

 Fingerprint Door Opener
Delete all attendance records in the device. Please backup
the data by USB flash drive or software first, before you
delete them.
 Slog Delete
Delete all the admin MENU operation records.
 Delete Enrolls
Delete all the enroll info on the device, including the
fingerprint, RFID card no, etc.
4.3. Messenger

MENU Log Data Message

Picture 26 Message

- 53 -【Chapter 4 Log Data】

 Fingerprint Door Opener

Figure 27 Message setting

Select the message group by pressing the ▲,.

- 54 -【Chapter 4 Log Data】

 Fingerprint Door Opener

Picture 28 Message setting

Message Setting method: need to use the Attendance

Management Software on your computer to set this
message info to the device, enter “Device Management ” 
“Add device” and connect software to the device  Message
 and set the message content, and upload to the device.
Please refer to the software manual for more info.

- 55 -【Chapter 4 Log Data】

 Fingerprint Door Opener
4.4. Log Info.

menu Log Data Log Info

Picture 29 Log Info

Figure 30 log info menu

 User： user amount that already enrolled in the device.

- 56 -【Chapter 4 Log Data】

 Fingerprint Door Opener

 Admin: admin amount that already enrolled in device.

 Fingerprint: fingerprint amount that already enrolled in

device.

 RFID card: RFID card amount that already enrolled in

device.

 GLog: attendance records that stored in the device.

 Slog: admin menu operation log amount.

4.5. tSegment (Clock in/clock out status on homepage)
it is the setting for the device auto change the status
Clock in, Clock out, overtime in, overtime out, etc. status
on the homepage. And this status will be along with the
attendance records on the software report.
MENU Log Data tSegment

Picture 31 tsetment
- 57 -【Chapter 4 Log Data】
 Fingerprint Door Opener

Picture 32 tsegment

Press ▲、 keys to select the item and press 【MENU/OK】

to change the status according to your requirement  press
【MENU/OK】to esc the settings. Device will auto save the
settings.
For example: when I set it to 8:00-9:00 CLK-IN, the device

- 58 -【Chapter 4 Log Data】

 Fingerprint Door Opener
homepage will shows “CLK-IN” during 8:00-9:00.

- 59 -【Chapter 4 Log Data】

 Fingerprint Door Opener

Chapter 5 U-disk
When device in homepage window, keep long pressing the
【MENU/OK】for 1 second to enter the device MENU (if you’ve
set the admin to the device, need get through the admin
verify first.),  【U-Disk】:

Picture 33 U-DISK

5.1. Download

- 60 -【Chapter 5 U-disk】
 Fingerprint Door Opener
Plug the USB flash drive to the device  U-Disk 
download:

Picture 34 download
 New GLog
Download the new attendance records that have never
been download before. When finish downloading, there’s a
“LogData” folder on your USB flash drive. And in this folder,

- 61 -【Chapter 5 U-disk】
 Fingerprint Door Opener
there’s a file “NewGlog_0001_20130216110320.csv”. the file
name would be changed according to different date.

 Historic GLog
Download all the attendance records that stored in the
device. When finish downloading, there’s a “LogData” folder
on your USB flash drive. And in this folder, there’s a file
“HisGLog_0001_20130216.csv”. the file name would be
changed according to different date.

 NEW Slog
Download the new admin menu operation logs that
never been downloaded before. Download the latest
management records, When finish downloading, there’s a
“LogData” folder on your USB flash drive. And in this folder,
there’s a file “NewSlog_0001_20130216110320.csv”. the file
name would be changed according to different date.

 Historic Slog

- 62 -【Chapter 5 U-disk】
 Fingerprint Door Opener
Download all the admin menu operation logs that stored
in the device. When finish downloading, there’s a “LogData”
folder on your USB flash drive. And in this folder, there’s a
file “HisSLog_0001_20130216.csv”. the file name would be
changed according to different.

 All Enroll Info

Download all the enroll info on the device, including the
fingerprint, RFID card no., etc. When finish downloading,
there’s a “UserData” folder on your USB flash drive. And in
this folder, there’s a file “AllEnrollData.fps”.

 Personnel enroll info

Download personnel enroll info. For example, Amaris
00000000001, after downloading Amaris’s enroll info, there’s
a “UserData” folder on your USB flash drive. And in this folder,
there’s a file “OD_000000000000000001.db”.

5.2. Upload

- 63 -【Chapter 5 U-disk】
 Fingerprint Door Opener
Plug the USB flash drive to the device  U-Disk  upload:

Picture 35 Upload
 All Enroll Info

Upload the enroll info data on the USB flash drive to the
Access Control device.

 Personnel Enroll Info

- 64 -【Chapter 5 U-disk】
 Fingerprint Door Opener

Upload someone’s enroll info from the USB Flash Drive to

the Access Control device. After upload successfully, the
device LCD will display his/her User ID. For example,
00000000001, it upload USER=1 enroll info..

 Firmware Upgrade
Upgrade the firmware to the device via the USB Flash drive.
Before upgrade, please backup the enroll info and
attendance records of the device. This action may cause the
device clear up all the info on the device.
Note: there’s risk for upgrade the firmware. If you are not
profession, it’s suggested not to upgrade the firmware.
During upgrade, you must keep the device energized –
power on, cannot enter the MENU, cannot plug off the USB
Flash drive before finish the upgrade. Else, it would damage
the device and may cause the device could not power on.
5.3. Download / Upload the data by the Attendance
management software

- 65 -【Chapter 5 U-disk】
 Fingerprint Door Opener
Chapter 6 Setting
When device in homepage window, keep long pressing the
【MENU/OK】for 1 second to enter the device MENU (if you’ve
set the admin to the device, need get through the admin
verify first.),  【Setting】:

6.1. System

MENU Setting System

Picture 36 System

- 66 -【Chapter 6 Setting】
 Fingerprint Door Opener

Picture 37 system
NOTE: Press ▲、 keys to select the item, and press
【MENU/OK】to enter the setting window.

 Language

Item Description
language Set device LCD display language

- 67 -【Chapter 6 Setting】
 Fingerprint Door Opener
Defaulted English

Form 3 LCD display Language Setting

 UI-theme (optional)

Picture 38 UI Themes

- 68 -【Chapter 6 Setting】
 Fingerprint Door Opener
Form 4 UI- Themes settings Descriptions
UI-Theme
Descriptions
settings
There’s defaulted to be 3 different background
Background here. And it’s defaulted to be the NO.2
background.
There’s defaulted to be 3 different time font.
Time Font And it’s defaulted to be the NO.3 font.(the time
showing on the home page of the LCD)
Set the title of the LCD homepage. It’s
Set main
defaulted to “Welcome” on the top left corner of
title
the LCD homepage.
Set standby
Set the title of the standby page.
title
Set the color for the LCD homepage title bye
Main title
modifying the RGB color value. (that is change
color
the color of the “Welcome” color)

- 69 -【Chapter 6 Setting】
 Fingerprint Door Opener
Set the color for the time (hour and minute font
color) by modifying the RGB color value. Such
Time color
as, the time is 11:12:35 now, and this item will
change the color for the 11:12
Set the color for the time (second font color) by
Second modifying the RGB color value. Such as, the
color time is 11:12:35 now, and this item will change
the color for the 35.
Set the color for the date (date font color) by
modifying the RGB color value. Such as, the
Date color
date is 2012/11/14 WED now, and this item
will change the color for the 2012/11/14.
Set the color for the date (week font color) by
modifying the RGB color value. Such as, the
Week color
date is 2012/11/14 WED now, and this item
will change the color for the WED.
The lunar item only defaulted for the Chinese
Lunar color
devices. Others language are defaulted to NO.

- 70 -【Chapter 6 Setting】
 Fingerprint Door Opener

Menu title Set the color for the title of the submenu by
color modifying the RGB color value.
Menu item Set the color for the item name of the submenu
color by modifying the RGB color value.
Set the color for the selected item.
Example: we select “1.System”, so the color is
different from other items.

Checked
color

Set the color for the ID number when in

V-ID color
attendance.

- 71 -【Chapter 6 Setting】
 Fingerprint Door Opener

V-name Set the color for the employee name when in

color attendance.
Set the color for the message. (Available for
some models only.)
V-message
The message will show in the following window
color
during attendance. for example “Happy
Birthday!”, the defaulted color is blue.

- 72 -【Chapter 6 Setting】
 Fingerprint Door Opener

Standby
Set the standby background color.
Bg-color
Standby Set the color for the font in standby
Font-color background.

- 73 -【Chapter 6 Setting】
 Fingerprint Door Opener
Restore
Restore all the UI-Theme to the default
default
settings.
settings

 Date & Time

Form 5 Date & Time Setting
Item Description

Date & Time Set the correct date and time according
to your local time zone.

 Date format
Form 6 Time Format Setting Description Table
Item Description

Time format Set Time format: YMD, DMY,MDY.

Default Y/M/D

 Volume Value

- 74 -【Chapter 6 Setting】
 Fingerprint Door Opener
Form 7 Volume value setting
Item Description

Volume value Volume from 0-6

default 3

 Admin. amount
Table 8 Total amount for the admin
Item Description

Admin. Max amount for enroll the admin on

device. Max:10
Default 5

 User ID Length
Form 10 User ID length
Item Description
User ID Length Set the User ID length, you could set
from 1-18.

- 75 -【Chapter 6 Setting】
 Fingerprint Door Opener
Default 11

 Verify mode
Table 11 Verify Mode
Item Description

Verify mode F / C: can use fingerprint or card for

verify.
F + C: must use fingerprint and card
together.
C: can use card verify only.
Default Any (could be Fingerprint / Card)

 Initial
Table 12 Initial device
Item Description

Initial When initial the device, it will clear up all

the data from device, including the enroll
info and the attendance records.

- 76 -【Chapter 6 Setting】
 Fingerprint Door Opener
6.2. Communication Settings

menu Setting. Comm.

Picture 39 Comm. Parameter setting

Picture 40 Communication parameter settings

 Device ID

- 77 -【Chapter 6 Setting】
 Fingerprint Door Opener
Form No. 13 Device ID.
Item Description

1~9999 Set fingerprint door openers

identification number.
Default 1

Note: Device ID is the unique mark for different Access

Control Devices. When you need to connect your software to
more than 1 device, the Device ID is the mark for different
devices. And differentiate the data and records from different
devices.
 Com. key
Form 14 Comm. Key setting
Item Description
0~99999999 Set TCP / IP communication access
password.
default 0 (means no password)

- 78 -【Chapter 6 Setting】
 Fingerprint Door Opener

 Port NO. (optional)

Form 15 TCP / IP port number settings
Item Description

1~65534 Set device TCP / IP communication

port.
Default 5500

Note: when you connect software to the Access Control

Device, need to put this port to the software connection
setting. Else, it cannot connect successfully.
 IP address (optional)
Form 16 IP Address Setting
Item Description
192.168.1.225 Set the IP address for TCP/IP
communication
default 192.168.1.225

- 79 -【Chapter 6 Setting】
 Fingerprint Door Opener

Note: The IP address of device must be unique on your

local LAN.
 subnet mask (optional)
Form 17 subnet mask Description Table
Item Description

255.255.255.0 Set subnet mask for the TCP/IP

communication.
default 255.255.255.0

 default gateway (optional)

Form 18 Default Gateway Setting
Item Description
192.168.1.1 Set default gateway for the TCP/IP
communication.
default 192.168.1.1

- 80 -【Chapter 6 Setting】
 Fingerprint Door Opener

Note: The subnet mask and default gateway must be

corresponding to your local LAN subnet mask and default
gateway.
 server IP(optional )
Form 19 servers IP Setting
Item Description
192.168.1.083 Set the server IP address.
when you need to use the UDP –
real-time monitoring function, need to set
your computer IP address to the “Server
IP”. For example, my Computer IP is
192.168.1.160, and I need to connect
software from my computer to the
device, and use the UDP function, so I
need set Server IP= 192.168.1.160.
please refer to push technology
description for more details.

default 192.168.001.083

- 81 -【Chapter 6 Setting】
 Fingerprint Door Opener

 server port (optional)

Item Description
0~65534 Server port for TCP/IP communication

default 5055

 RS485(optional)
Form 20 RS485 communication setting
Item Description
YES/NO Enable RS485 or not
default NO

 baud rate (optional)

Form 21 Baud Rate Setting
Item Description
9600 Baud rate for TCP/IP communication

- 82 -【Chapter 6 Setting】
 Fingerprint Door Opener
19200 Communication port baud rate is set
to19200bps
38400 Communication port baud rate is set
to38400bps
57600 Communication port baud rate is set
to57600bps

115200 Communication port baud rate is set

to115200bps
default 115200

 GLog RT Push (optional)

Form 22 Live Upload Settings Description Table

Item Description
RS485/UDP Support real time upload or not
default NO

6.3. Sensor

- 83 -【Chapter 6 Setting】
 Fingerprint Door Opener

Menu Setting sensor

Picture 41 Sensor setting

Picture 42 Sensor settings

 Automatic learning
Form 23 sensor setting
Item Description

- 84 -【Chapter 6 Setting】
 Fingerprint Door Opener
YES Device will auto refresh user’s
fingerprint to the latest.
default YES

 Auto bright

When the Device is being using for a long time, and the
sensor is not sensitive as beginning, we can use this sensor
to adjust it.
6.4. Alarm

- 85 -【Chapter 6 Setting】
 Fingerprint Door Opener

Picture 43 Timing bell setting

Timing bell Settings: set a time, and the device will ringing at
that time.
Method 1 :
Select the group by the key ▲,  and set the time
according to your requirement.
For example, I set it Time=11:45 cycle=Day, Delay=005. So
every day the device will ring for 5 seconds at 11:45.
Method 2 :

- 86 -【Chapter 6 Setting】
 Fingerprint Door Opener
We could connect the device to the software and set it
through the software: Device management – add device –
device control – bell and set the time and upload to the
device.

6.5 power
When device in homepage window, keep long pressing the
【MENU/OK】for 1 second to enter the device MENU (if you’ve
set the admin to the device, need get through the admin
verify first.),  【Setting】 【Power】:

- 87 -【Chapter 6 Setting】
 Fingerprint Door Opener

Picture 44 Power
 auto return time (seconds)
Form 24 auto return time
Item Description

5~255 For example, we set it to 25

seconds. When you enter the MENU

- 88 -【Chapter 6 Setting】
 Fingerprint Door Opener
and 25seconds without any
operation, the device will ESC
the menu to the Homepage of the
LCD automatically.
default 9

 Power off time

You could set 24 shutdown time.
For example, when you set it to 19:00, the device will
shut down at 19:00 automatically.
 Auto off
Form 25 auto off setting
Item Description

0~255（min） When set it to 50mins, the device

will turn off after turn on for

- 89 -【Chapter 6 Setting】
 Fingerprint Door Opener
50minutes.

default No

 Sleep Time (min)

Form 26 Sleep Time Setting
Item Description

0~255（min.） Set how many minutes after the door

opener still goes to sleep

Factory setting No

 Alarm in sleep mode

Form 27 alarm in standby setting
Item Description

- 90 -【Chapter 6 Setting】
 Fingerprint Door Opener
YES When the device is on standby mode
during the alarm time, enable the
alarm or not?
default Yes

 Enable shutdown
Form 28 to enable shutdown
Item Description

Yes Enable the power key or not? When

you disable it, and people press
the power key“POW/ESC", s/he
cannot turn on the device.
default yes

- 91 -【Chapter 6 Setting】
 Fingerprint Door Opener

6.6 S-Test
When device in homepage window, keep long pressing the
【MENU/OK】for 1 second to enter the device MENU (if you’ve
set the admin to the device, need get through the admin
verify first.),  【Setting】 【S-test】:

Picture 45 S-test
 Check Sensor

- 92 -【Chapter 6 Setting】
 Fingerprint Door Opener
Move the cursor to the “Check Sensor” and press “OK” to
check the sensor. Press the finger on the sensor according
to the LCD tips. When there’s the fingerprint image on the
LCD, that means the sensor works well.

 Card RFID
Move the cursor to the “Check RFID” and press “OK” to
check the RFID detection. Put the RFID card on the
detection zone according to the LCD tips. When the RFID
num shows on the LCD , that means the RFID function
works well.

 Check LCD
Move the cursor to the “Check LCD” and press “OK” to check
the LCD. Check the LCD color according to the tips. When
all the color matches the LCD tips, that means the LCD
works well.

 Check Soundtest

- 93 -【Chapter 6 Setting】
 Fingerprint Door Opener
Move the cursor to the “Check Sound ” and press “OK” to
check the sound. Check if there’s the sound comes out, if
yes. That means the speaker works well.
 Check keyboard
Move the cursor to the “Check Keyboard” and press “OK” to
check the keyboard. Press the keyboard according to the
LCD tips.

- 94 -【Chapter 6 Setting】
 Fingerprint Door Opener

Chapter 7 ACS
When device in homepage window, keep long pressing the
【MENU/OK】for 1 second to enter the device MENU (if you’ve
set the admin to the device, need get through the admin
verify first.),  【ACS】:

Picture 46 Access control setting

- 95 -【Chapter 7 ACS】
 Fingerprint Door Opener
7.1. D-Lock (door lock)
When device in homepage window, keep long pressing the
【MENU/OK】for 1 second to enter the device MENU (if you’ve
set the admin to the device, need get through the admin
verify first.),  【ACS】【D-lock】 :

Picture 47 door lock setting

 Open delay

- 96 -【Chapter 7 ACS】
 Fingerprint Door Opener

Item Description
1-255
open delay(s)

After this value, the device send a close

door signal to the door.

No Device sends out the close door signal

immediately after sending out the open door
signal.
default 5

 Check door status

Item Description

YES Detect door sensor status. (if need to set a

time out alarm/ illegal open alarm, need to
set “check door status” to “YES”)

- 97 -【Chapter 7 ACS】
 Fingerprint Door Opener
NO Not detect door sensor status.

default NO

 time out alarm

Item Description

1-255 Detect the door sensor status within the

setting time. If the door sensor status is
not same as the door sensor setting status,
Device will send out a alarm signal.
For example, if we set it to 5s, when door
keep open for more than 5s, the device will
send out an alarm. And the Alarm that
connected to the “ALM0” and “ALM1” will
be active.
No No alarm signal.

default No

 Illegal open alarm

- 98 -【Chapter 7 ACS】
 Fingerprint Door Opener

Item Description
1-255 Detect the door sensor status within the
setting time. If the door sensor status is
not same as the door sensor setting status,
Device will send out a alarm signal.
For example, if we set it to 1s, when door is
opened illegally for 1s, the device will send
out an alarm. And the Alarm that connected
to the “ALM0” and “ALM1” will be active.
No No alarm signal.

default No

 External bell

Item Description

Yes When set to [Yes], the timing bell will send

to the connected external alarm which is
connected to the “ALM0” and “ALM1”.

- 99 -【Chapter 7 ACS】
 Fingerprint Door Opener
No The timing bell can be ringing in the device
speaker only. It cannot send the signal to
the external alarm.
Factory No
setting
Note: ALM0 & ALM1 can connect to one equipment only.
For example: when this interface is connected to the Belling,
the “Fire alarm” function will not be active. If you need
connect to the fire alarm, please set the “external bell” to “NO
 Fire alarm

Item Description

YES Set to “YES”, and the interface “CTL1”

connect to the fire alarm (low-level input).
Device will open the door automatically and
send out the signal to the alarm that
connected to the “ALM0” and “ALM1”.
(NOTE: the open delay cannot set to
“NO”)

- 100 -【Chapter 7 ACS】

 Fingerprint Door Opener
No This function is disabled.

default No

 Wiegand

Item Description

26 Wiegand 26 signal on Wiegand 26

interface.
34 Wiegand 34 signal on Wiegand 34
interface.
66 Wiegand 66 signal on Wiegand 66
interface.
default 34

 Auto. unlock lock 1 - pGroup

Description: After verify, in the available passing

through time, the Lock 1 will keep open / keep closed.

- 101 -【Chapter 7 ACS】

 Fingerprint Door Opener

Please refer to the installation manual for the NO/NC

lock connection.

Item Description

1—30 It’s the pass through group

default No

 Lock control

Item Description

status Displays the current state of the lock

settings
Lock control Default to " master" (" slave " invalid, do
not set)
NO Normally open
NC Normally closed

- 102 -【Chapter 7 ACS】

 Fingerprint Door Opener
Normal Normal status

7.2. User control

When device in homepage window, keep long pressing
the 【MENU/OK】 for 1 second to enter the device MENU
(if you’ve set the admin to the device, need get through
the admin verify first.),  【ACS】【UserCtrl】 :

Setting Default Description

setting
User 0000000000 Set the settings to the selected
Control 1 User ID.
User 0 Set the current User ID to a
group Pass group.
Manager could set the “ACS”
“pSegment””pGroup”and”pZone
” according to the requirement.
Validity No Select [Yes]. And active the
period access control to the current

- 103 -【Chapter 7 ACS】

 Fingerprint Door Opener
User ID.

Begin 2010/01/01 The user's valid range.

00：00
End 2090/12/31
00：00
Locks Master-slave Determine whether the user has
Permissi (options are the privilege to open the door.
on divided into:
Master,
slave,
master-slave
, and no.)
7.3. Hijack
When device in homepage window, keep long pressing
the 【MENU/OK】 for 1 second to enter the device MENU
(if you’ve set the admin to the device, need get through
the admin verify first.),  【ACS】【Hijack】 :

- 104 -【Chapter 7 ACS】

 Fingerprint Door Opener

Picture 48 Hijack setting

Item Default Description

Enable No Enable anti-hijack or not

anti-Hijack
Hijack FP 2 For example: Amaris (ID=001),
NO. enroll 5 fingerprint. And when she
registered the second fingerprint
(00000000001-2), this fingerprint I
the Hijack FP. When we enable the

- 105 -【Chapter 7 ACS】

 Fingerprint Door Opener
anti-hijack function on the Access
Control Device, and some
stranger forced her to open the
door, she use the NO=2 fingerprint
to verify. The device will mark this
record as the anti-hijack. If we
enable the alarm, the device will
send out a signal to the alarm.

Open Yes When people use the hijack fp to

verify, the door will open or not?
Alarm No When people use the hijack fp to
verify, the Access control device
will send out a signal to the alarm?
If we set it to “YES”, then the
device will send out the alarm
signal, and the alarm connected to
“ALM0”&”ALM1” will be aactive.
7.4. pSegment

- 106 -【Chapter 7 ACS】

 Fingerprint Door Opener
When device in homepage window, keep long pressing
the 【MENU/OK】 for 1 second to enter the device MENU
(if you’ve set the admin to the device, need get through
the admin verify first.),  【ACS】【pSegment】 :

Picture 49 Pass segment setting

- 107 -【Chapter 7 ACS】

 Fingerprint Door Opener

Note: it’s not editable for the group0 and group 31.
Group0: 00:00-23:59 (it means it’s available to pass through
all day long). Group31:00:00-00:00 (it means it’s unavailable
to pass through all day long).

00. 00：00-23：59

01. 6：00-9：00

02. 11：00-14：00

03. 17：00-19：00

… …

Pass-time 31 00：00-00：00

7.5. Pass group

There’re 32 groups (0-31 groups) for pass group. Every pass

- 108 -【Chapter 7 ACS】

 Fingerprint Door Opener
group can set with 10 pass Segment.

Picture 50 P.Group setting

Select any Group NO. and press 【MENU/OK】to set the 10
p.segment to that pass group.

Note: in the selected Group, you can press 【MENU/OK】

to set different p.segment to it. Group0 and Group31 are not
editable. 10 P.Segment set to Group0 is
P.Segment0(00:00-23:59), that means can pass through all

- 109 -【Chapter 7 ACS】

 Fingerprint Door Opener
day long. 10 P.Segment set to Group31 is
P.Segment31(00:00-00:00), that means cannot pass through
all day long.

1 2 3 4 5 6 …

0 P.Seg P.Segm P.Se P.Seg P.Seg P.Segm …

ment0 ent0 gme ment ment ent0
nt0 0 0

1 P.Seg P.Segm P.Se P.Seg P.Seg P.Segm …

ment1 ent2 gme ment ment ent31
nt6 7 31

2 P.Seg P.Segm P.Se P.Seg P.Seg P.Segm …

ment2 ent4 gme ment ment ent31
nt6 31 31

- 110 -【Chapter 7 ACS】

 Fingerprint Door Opener

3 P.Seg P.Segm P.Se P.Seg P.Seg P.Segm …

ment2 ent3 gme ment ment ent31
nt4 5 6

3 P.Seg P.Segm P.Se P.Seg P.Seg P.Segm …

1 ment31 ent31 gme ment ment ent31
nt31 31 31

7.6. Pass Zone

P.Zone, we could set 32 P.Group to every P.Zone. and in
every P.Zone, there’s setting for Monday to Sunday. We
could set different P.Zone according to different requirement.

- 111 -【Chapter 7 ACS】

 Fingerprint Door Opener

Picture 51 pass zone setting

Select any PZone NO. and press 【MENU/OK】to set the
p.Group to that pass Zone.

Note: in the selected P.Zone, you can press 【MENU/OK】

to set different p.Group to it. p.Zone0 and p.Zone31 are not
editable. P.Zone0 : 7days set to p.Group0, means can get
through all the whole week. P.Zone31 : 7days set to
p.Group31, means cannot get through all the whole week.

- 112 -【Chapter 7 ACS】

 Fingerprint Door Opener

Sun Mon Tue Wed Thu Fri Sat

P.Zone P.Gro P.Gro P.Gro P.Gro P.Gro P.Gro P.Group

0 up 0 up 0 up 0 up 0 up 0 up 0 0

P.Zone P.Gro P.Gro P.Gro P.Gro P.Gro P.Gro P.Group

1 up 1 up 1 up 1 up 1 up 1 up 1 1

P.Zone P.Gro P.Gro P.Gro P.Gro P.Gro P.Gro P.Group

2 up 31 up 2 up 2 up 2 up 2 up 2 31

P.Zone P.Gro P.Gro P.Gro P.Gro P.Gro P.Gro P.Group

3 up 3 up 3 up 3 up 3 up 3 up 3 3

P.Zone P.Gro P.Gro P.Gro P.Gro P.Gro P.Gro P.Group

31 up 31 up 31 up 31 up 31 up 31 up 31 31

- 113 -【Chapter 7 ACS】

 Fingerprint Door Opener
 How to set the pass through time to the Users?

We could set the pass through time to different users

according to different requirement, so we could have strict
limit that which users can get through the door at what time.
For example:
User A. work for night shift all the week, she cannot get
through the verify at day time.
User B. normal work at day shift, can get through during his
working time. Saturday & Sunday rest.
User C. work for day shift all the week, cannot get through
the verify at night.for the entire week on duty day and cannot
access in night.

P.Zone Pass through time

A 1 00:00-9:00;17:00-23:59

B 2 6:00-9:00;11:00-14:00;17:00-19:00

C 3 6:00-19:00

- 114 -【Chapter 7 ACS】

 Fingerprint Door Opener

Chapter 8 Device Information

Picture 52 Device Hardware & Firmware Info.

When device in homepage window, keep long pressing
the 【MENU/OK】 for 1 second to enter the device MENU
(if you’ve set the admin to the device, need get through
the admin verify first.),  【ACS】【pSegment】

- 115 -【Chapter 8 Device Information】

 Fingerprint Door Opener
Item Description

S/N Device serial number.

Date Equipment production date.

Add Device MAC address.

Soft Device firmware version.

Engine Device Algorithm version.

Fingerprint Device Fingerprint capacity.

General Log Device record capacity.

- 116 -【Chapter 8 Device Information】

 Fingerprint Door Opener

Chapter 9 FAQ
1. How to remove the admin privilege on the device
menu?
 We could remove the privilege through the software
(Method 1)
It’s recommend that enroll at least 2 admin to the device.
so when lose one admin, still can enter the menu of the
device.
When you lose the only one admin, and cannot enter to
the Device MENU, please connect the device to the
software, and cancel the privilege on the software.
Details:
1) Connect the device to the software through the
USB connection. (if your device supports TCP
communication, you could use the TCP
connection also.)
2) Run the software, enter the “Device
Management” window, connect the device to the

- 117 -【Chapter 9 FAQ】

 Fingerprint Door Opener
software, and click “Cancel privilege”, as the
following:

Picture 53 cancel privilege by Software

3) When you need to enroll the admin to the device

again, please refer to the enrollment details
- 118 -【Chapter 9 FAQ】
 Fingerprint Door Opener
above.

 We can also remove the admin privilege by pressing a

key on the mainboard. (Method 2)
1) Turn off the device
2) Open the back case, find the SW2 key on the
mainboard as the following:

- 119 -【Chapter 9 FAQ】

 Fingerprint Door Opener

Picture 54 cancel privilege on Hardware.

3)Turn on the device, and press the SW2 key again.

- 120 -【Chapter 9 FAQ】

 Fingerprint Door Opener
4)And there’s a tips on the LCD now:

Picture 55 cancel privilege on hardware

And press “OK” to remove the admin privilege.

- 121 -【Chapter 9 FAQ】