Introduction to 007 Signal Detector

Cell phone Detector is to send the audio or video signal through electromagnetic waves. It is
a machine designed to detect and fix the position of the hidden wireless tapping device.

As the technology of wireless tapping develops, the performance of such devices are also
being promoted. They become increasingly difficult to be detected with their small size, low
emitting power, complicated modulation, wide range, high speed, remote controllability and
conceal ability.

Cell phone detector is designed to detect and concisely determine the location of the
working tapping device in the targeted venue. It is one of most advanced portable wireless
signal detectors.

Features:
 Professional, sensitive, with modularly threshold and wide detecting frequency range;
 Sound and light alarm indicator makes it easy to use;
 Applicable to military, government, business and other venues;
 Good electromagnetic compatibility;
 Small and portable.

Specification:
 Detecting frequency range: 20MHz-6000MHz
 Main detecting frequency range: 800MHz-2200MHz
 Detecting sensitivity: ≤0.05mw (in main detecting frequency range)
 Working range: >70Db
 Indicator: 9 grades of LED light indicators / tonal modification sound indicator
 Battery: 9V packed cell

Control Panel Description:

1
Wireless tapping device: the audio/video signals received by the front sensor are sent
through the modulated wave of high frequency to a receiving device in a certain distance
which can restore those signals.

Wireless tap detector: an analogue detecting method of wide frequency range is applied to
the machine. It can detect the field intensity of signals emitted from the tapping device and
concisely determine the location of it according to the change of field strength.

Operational Manuals:
1. The machine should be held in hand when working. The SMA socket on the top is for
antenna. The two oval holes on the upper right of the face board are for loudspeaker. In the
middle of the left side are 10 grades of LED indicators, the first of which indicates the power
and the others indicate the strength of detected signals. The last one shows the strongest
signal. The knob at the bottom is for power and detecting threshold modulation.
Screw the antenna to the socket. Loosen the screws on the back cover. Pull out the inner
battery pool and press the 9V packed cell into it with the poles in the right direction (make
sure the power knob is off before the battery is installed). And then fix the back cover with
tightened screws.

2. Turn the bottom knob to the right until it make a sound of “ka”. The power is turned on
now and all the LED indicators are also lighted. Continue to turn the knob to the right and
the LED indicators will be off one by one from right to left. Meanwhile, the tone of the
loudspeaker goes from high to low. Generally the machine becomes most sensitive when the
third LED indicator from the left is just turned off. When the machine gets closer to the
working tap device, the LED indicators will be turned on one by one and the tone of the
loudspeaker will become higher and higher. There may be still a small distance from the
tapping device and reset the knob to make the machine in the most sensitive state as said
before. When the LED indicators and the tone of the loudspeaker have great change, the
location of the tapping device can be determined.

3. It should be applied to a small space (within 20 m2) to detect close electromagnetic signals
with evident field strength change. The remote signals might be strong, but their field
intensity generally remains the same and can’t be detected by the machine. The user should
be familiar with the electromagnetic circumstance of the targeted venue.

4. Set the detecting threshold before enter the targeted venue and then move around in the
targeted venue. Watch the LED indicators and switch the threshold accordingly. Such office
equipment as telephone, table lamp, fax should be detected when they are on. If the tapping
device is fixed on these equipment, it’s detectable distance is just within 20cm and only
several LED indicators have reflections even when the machine is in the most sensitive state.
If the LED indicators show evident change around any substance, it should be further
surveyed. The reflected electro-wave out of metal substance in the building forms standing
wave, which will make the LED indicators react violently. If there is no substance, there will
be no worries. If there is, it is necessary to move around to do the detection. The more
familiar the user is to the targeted place, the shorter it takes to do the detection. If the user
stands still but the indicators show sudden and violent change, it means that there are
signals emitted nearby. The signals from cell phone, microwave oven, electromagnetic
cooker or other electrical appliance should be excluded. However, the cell phone is possible
to be tapped.

Remarks:
1. The 9V packed cell is commonly used and sufficiently supplied in the market. But the
quality of this kind of battery will decide its price. Please use the battery of high quality.
2. The LED indicator should be on in sequence. If one of the indicator is off while other
indicators on its sides are on, there is fault to the machine and it need to be repaired.
When the rest two LED indicators are on, it usually means the battery almost power off.
3. The sound alarm and LED indicators should act simultaneously. If the sound alarm goes
without the LED indicators’ change or otherwise, the machine needs to be repaired.
When all the LED indicators are on but there is no sound alarm, it is because of the
extremely high frequency and it would turn normal when the threshold is modulated.

2
 [Link]

Remarks:

When it is operation, pls try to adjust

When the detector is more close to the cell phone, the LED lights,
will be flicking more frequently.