MasterSeal® 610
Water based bitumen emulsion
DESCRIPTION TYPICAL PROPERTIES
MasterSeal 610 is a non-fibrated, water based bitumen
emulsion. It is dark brown in colour and dries to a black Flashpoint: Non flammable
flexible protective coating. The finished film is tough and Specific gravity: 1.20 +- 0.01@ 25°C
waterproof and forms a barrier to water and vapour Application Temperature 5°C to 50°C
transmission. Service temperature: -10°C to 85°C (de-
pending on Operating
TYPICAL APPLICATIONS conditions)
• General waterproofing and damp proofing of concrete, Chemical resistance: Excellent to water, dilute
asbestos cement, roofing felt, slate tiles, wood, etc. acids,
• Metal protection: provides protection for structural alkalis, chloride and
steelwork, pipes, etc. sulphate ions
• Insulation: provides a vapour barrier for cold Flexibility: Provides a firm flexible
storage rooms, etc. coating
• Protection to a variety of buried structures such as
concrete foundations and retaining walls. PERFORMANCE:
Concrete coated with MasterSeal 610 will prevent the
ADVANTAGES absorption of saline solutions. On uncoated surfaces,
• Chemical resistance. salts in groundwater will penetrate and can cause
• Versatile. reinforcement corrosion and concrete deterioration.
• Economical
• Easy to apply. APPLICATION:
• Cold applied. Agitate before use. As settlement can occur,
the drum should be rolled before decanting
PACKAGING material.
MasterSeal 610 is available in 16 and 200 litre drums Apply by brush, broom or squeegee. Apply one or
two coats, depending on the degree of protection
COMPOSITION required. Apply subsequent coats at right angles to
A blend of selected asphalts and bitumens emulsified in
the first, allowing 12 to 24 hours between coats.
water
Where being utilised to damp proof solid floors or
where a screed is to be applied over MasterSeal
APPLICATION PROCEDURE 610 , apply a second coat at right angles and
SURFACE PREPARATION lightly grit to form a key. Allow at least 24 hours
Ensure surface to be treated is sound and free of all oil, before application of concrete screed, ensuring this
grease or conventional curing compounds. MasterSeal is greater than 50mm in thickness.
610 can be applied directly to concrete surfaces cured
utilising non-degradable curing compounds such as COVERAGE
MasterKure 181. 3-6 m² per litre per coat depending on substrate
If the surface is dusty it should be primed with a coat of porosity.
MasterSeal 610 diluted with an equal quantity of clean
water and allowed to dry, before applying further coats of EQUIPMENT CARE
MasterSeal 610 . MasterSeal 610 can be applied to
After use, if the MasterSeal 610 has not dried, it
damp surfaces, although both coating and surface must
may be possible to clean tools using soapy water. If
be allowed to dry before the MasterSeal 610 will cure to
the MasterSeal 610 has dried remove as much as
form a waterproof film.
possible by physically scraping and then remove
remainder with paraffin, white spirit or CLEANING
SOLVENT NO. 2.
December 2020 Page 1 of 3
MasterSeal® 610
Water based bitumen emulsion
STORAGE: mouth, skin and foodstuffs. Treat splashes to eyes
Store under cover, out of direct sunlight and protect and skin immediately. If accidentally ingested, seek
from extremes of temperature. In tropical climates medical attention. Reseal containers after use. Use
the product must be stored in an air-conditioned in well ventilated areas and avoid inhalation. For fur-
environment. As with all bituminous emulsions, ther information refer to the material safety data
some settlement will occur with prolonged storage. sheet.
It is, therefore, necessary to invert the drums
monthly to disperse the settlement. NOTE
Shelf life is up to 6 months in unopened containers, Field service, where provided, does not constitute
when stored as above. supervisory responsibility. For additional information
Failure to comply with the recommended storage contact your local representative.
conditions may result in premature deterioration of Reserves the right to have the true cause of any dif-
ficulty determined by accepted test methods.
the product or packaging. For specific storage ad-
vice consult MBCC's Technical Services Depart-
QUALITY STATEMENT
ment.
This statement is made under condition that the material
and usage thereof conform to the terms of our published
SAFETY PRECAUTIONS
literature and recognized good workmanship
As with all chemical products, care should be taken
during use and storage to avoid contact with eyes,
Whilst any information contained herein is true, accurate and represents our best knowledge and experience, no warranty is
given or implied with any recommendations made by us, our representatives or distributors, as the conditions of use and the
competence of any labor involved in the application are beyond our control
CONTACT
Should you require any further information, please do not hesitate to contact us:
Jordanian Swiss Company for Manufacturing and Marketing Construction Chemicals,
Web: [Link]
[Link]/en-jo
Email : Info-Jo@[Link]
Tel: +962-6 5521672
P.O. Box 752 ,11118, Amman, Jordan
Fax: +962 6 5523148
December 2020 Page 2 of 3
