POLYFLAME

APP Modified Waterproofing Membrane

DESCRIPTION FINISHES
BITUMAT POLYFLAME is a superior, high BITUMAT POLYFLAME is available in three basic
performance, prefabricated, modified bitumen finishes:
membrane consisting of proprietary Black smooth finish with polyethylene
waterproofing compound, reinforced with spun surfaces for covered applications.
bonded non-woven polyester mat. Granule surfacing for exposed
applications.
The BITUMAT proprietary waterproofing compound Fine sanded upper surface for coated
systems.
is formulated with select bitumen modified with
Attactic Polypropylene (APP) for greater QUALITY CONTROL
elasticity, flexibility, and further enhanced with a In addition to stringent regular tests by BITUMAT
blend of Thermoplastic Polymer (TP) and laboratory, our products are tested periodically by
Elastoplastic Copolymer (EPC) for high heat Independent Laboratories.
resistance, greater elongation and low
temperature flexibility. The compound is then STANDARDS
stabilized with opaque Mineral Stabilizers (MS) BITUMAT POLYFLAME complies with the
for impact resistance, UV resistance and performance requirements and tolerance levels of
durability. the listed standards. Some of which modified to
better suit the various climatic conditions around
The superior waterproofing compound is the world.
reinforced with a robust, isotropic, spunbonded, 1. American Society for Testing and Materials,
non-woven polyester mat for increased strength, ASTM D-6222 Type II.
toughness and dimensional stability. 2. European Union of Technical Agreement
(UEAtc)
The proprietary compound, the unique 3. Canadian General Standard Board (CGSB
reinforcement, combined with the famous 37-GP 56M - July 1980).
BITUMAT process technology and rigid quality 4. German Standard DIN 52133.
assurance procedures, yield the most reliable and
dependable waterproofing membrane. INSTALLATION TOOLS REQUIRED:
Gas torch, Knife, Trowel, Measuring tape,
Marking string, Gloves.
USES
BITUMAT POLYFLAME is a universal, all purpose APPLICATION
membrane, excellent in a single layer or multi BITUMAT POLYFLAME is installed by torch
layer roofing systems, underground waterproofing, welding method, loose-laid or fully bonded to
multi-story car parks, pond lining, irrigation canals substrate. When loose-laid, only overlaps are
lining, swimming pools or any structure that bonded together. Peripheres , protrusions and
requires high performance waterproofing. other flashing details are installed according to
specifications.
OUTSTANDING FEATURES
Total impermeability for total waterproofing. COVERAGE RATE (Approx.)
Excellent resistance to aging and weathering. (Rate may vary as per site requirement)
Outstanding bondability and seam integrity.
Flexibility at low temperature. Flat areas : 1.15 M2/M2 per layer with 10
Stability at high temperature. cms. side laps and 15 cms.
Very high resistance to impact & puncture. end laps.
Application friendly (labour cost savings) Base flashing : 100x35 cms. with 15 cm. end
Variety of finishes for exposed and covered laps, 0.40 M2/ linear M
applications. Average wastage : 3 - 5 %
High tensile strength and tear resistance.
Excellent for mechanical anchorage. TORCHING GUIDELINES
The underside of the membrane should be torched
Isotropic properties.
just enough to superficially melt the
bitumen. Excessive heating may damage the
GENERAL DATA reinforcement. Overlaps should be re-heated from
Nominal Roll length : 10 Mt. the top and resealed with a trowel to
Nominal Roll width : 1 Mt. ensure seam integrity.
Nominal Thickness : 3, 4, 5, MM
For details of installation methods and flashing
Reinforcement requirements, consult the relevant BITUMAT
Robust, isotropic, spunbonded non-woven Systems Design and Installation Manual.
polyester core, 200/180 gms/m2 depending on
thickness. Other weights available on request.
POLYFLAME
APP Modified Waterproofing Membrane

TECHNICAL DATA
Property Typical Value Test Method
1. Softening point, °C 155 ASTM D 36
2. Penetration, @ 25 °C, dmm 20 ASTM D 5
3. Low temperature flexibility, °C -6 to -10 ASTM D 5147
4. Heat resistance, compound stability
@ 120 °C for 2 hours & 15 minutes No flow - Pass ASTM D 5147
5. Tensile strength, N/5 cm @ 23+2 °C
Longitudinal 950 (19 KN/m) ASTM D 5147
Transverse 800 (16 KN/m)
6. Tensile strength, N/5 cm @ -18+2 °C
Longitudinal 1200 (24 KN/m) ASTM D 5147
Transverse 950 (19 KN/m)
7. Elongation, % @ 23 + 2°C
Longitudinal 45 ASTM D 5147
Transverse 50
8. Elongation, % @ -18 + 2°C
Longitudinal 24 ASTM D 5147
Transverse 26
9. Load strain product, @ 23 + 2°C
Longitudinal 42,750 CGSB-37-GP-56M
Transverse 40,000
10. Load strain product, @ -18 + 2°C
Longitudinal 28,000 CGSB-37-GP-56M
Transverse 24,700
11. Lap joint strength, N/5 cm
Longitudinal Same as membrane CGSB-37-GP-56M
Transverse UEAtc
12. Tear resistance, N
Longitudinal 600 ASTM D 5147
Transverse 400
13. Tear strength, N
Longitudinal 190 UEAtc
Transverse 210
14. Puncture Resistance, N 1155 ASTM E 154.
Static indentation L4 UEAtc 5.1.9.
Dynamic indentation I4 UEAtc 5.1.10
15. Water Absorption, %Wt @ 23 °C 24 hrs. <1 ASTM D 5147
16. Water Vapour Transmission, ASTM E 96 procedure E
g/m2/24 hrs. <0.5 37.8 °C at 90% RH
17. Dimensional Stability, %
Longitudinal + 0.5 ASTM D 5147
Transverse - 0.5
18. Resistance to Leakage at joints Pass UEAtc
19. Resistance to aging & U.V. No change ASTM
(Weather-O-meter, 2000 hrs) greater than 20% G53
of the original values UNI 8202
The information given in this Technical Data Sheet reflects typical median properties based on laboratory test, and practical experience; subject to the tolerance levels of UEAtc directives.
However, as the product is often used under conditions beyond our control, we can’t warrant but the product itself.
THIS PUBLICATION AUTOMATICALLY SUPERSEDES ALL PREVIOUS PUBLICATIONS RELATING TO THIS PRODUCT.

MSD 09/2003