Viking Installation Guide
Viking Range Corporation
111 Front Street
Greenwood, Mississippi 38930 USA
(662) 455-1200
For product information,
call 1-888-VIKING1 (845-4641)
or visit the Viking web site at
[Link]
Microwave Built-In Trim Kit
F20196C (010708J)
TINSEB453MRRO
IMPORTANT - PLEASE READ AND FOLLOW BASIC SPECIFICATIONS
•Before beginning, please read these instructions completely and carefully.
•Be sure to DISCONNECT THE PLUG of the microwave oven from the electrical outlet before installing the built-in trim kit. Remove Microwave Oven Built-In Trim Kits
the turntable from the oven cavity. VMOS200 VMTK270/271 VMTK300/301 VMTK360/361
•Because the kit includes metal parts, caution should be used in handling and installation to avoid the possibility of injury. Overall Width 24” (60.9 cm) 26-1/2” (67.3 cm) 29-1/2” (74.9 cm) 35-1/4” (89.5 cm)
•Do not remove permanently affixed labels, warnings, or plates from the product. This may void the warranty. Overall Height from Bottom 13-3/8” (33.9 cm) 18-1/4” (46.3 cm) 18-1/4” (46.3 cm) 18-1/4” (46.3 cm)
•Please observe all local and national codes and ordinances.
Overall Depth from Rear 19-3/8” (49.2 cm) N/A N/A N/A
•The installer should leave these instructions with the consumer who should retain for local inspector’s use and for future
reference. Oven Interior Width - 17-3/8” (44.1 cm) N/A N/A N/A
Height - 10-1/2” (26.6 cm)
Depth - 18-5/8” (47.3 cm)
THIS BUILT-IN KIT IS DESIGNED FOR USE ONLY WITH VIKING MICROWAVE OVENS SPECIFYING BUILT-IN KIT Overall - 2.0 cu. ft.
VMTK270/271, VMTK300/301, OR VMTK360 FOR PROFESSIONAL UNITS AND DMTK270 OR DMTK300 FOR Cutout Width N/A Min. - 24-3/8” (61.9 cm)
DESIGNER UNITS ON THE RATING LABEL ON THE LEFT SIDE WALL OF THE OVEN CAVITY.
Max. - 24-11/16” (62.7 cm)
IF YOUR LOWER CONVENTIONAL OVEN IS NOT LISTED IN THE USE AND CARE MANUAL OF THE MICROWAVE Cutout Height N/A Min. - 16-3/4” (42.5 cm)
OVEN, THEN DO NOT INSTALL THE MICROWAVE OVEN ABOVE IT OR IN ANY AREA WHERE HEAT AND STEAM
Max. - 17” (43.2 cm)
ARE GENERATED; FOR EXAMPLE, NEXT TO OR ABOVE A CONVENTIONAL RANGE.
Cutout Depth N/A Min. 20” (50.8 cm)
PARTS INCLUDED IN THE VMTK KIT PARTS INCLUDED IN THE DMTK KIT Electrical Requirements 120VAC/60 Hz N/A N/A N/A
Max. Amp Usage 1.65 KW; 13.5 amps N/A N/A N/A
1) Front Frame Assembly - QTY 1 1) Frame Assembly - QTY 1
Approximate Shipping Wt. 55 lbs. (24.7 kg) 14 lbs. (6.5 kg) 15 lbs. (6.9 kg) 16 lbs. (6.9 kg)
Front Frame Sub-Assembly;
Back Frame Sub-Assembly
Microwave Oven Built-In Trim Kits
2) Exhaust Duct Assembly - QTY 1 DMOS200 DMTK270 DMTK300
Overall Width 24” (60.9 cm) 26-1/2” (67.3 cm) 29-1/2” (74.9 cm)
Overall Height from Bottom 13-3/8” (33.9 cm) 18-1/4” (46.3 cm) 18-1/4” (46.3 cm)
2) Exhaust Duct Assembly - QTY 1
Overall Depth from Rear 19-3/8” (49.2 cm) N/A N/A
Oven Interior Width - 17-3/8” (44.1 cm) N/A N/A
Height - 10-1/2” (26.6 cm)
Depth - 18-5/8” (47.3 cm)
3) Screw A (1/2” length) - QTY 2
Overall - 2.0 cu. ft.
Cutout Width N/A Min. - 24-3/8” (61.9 cm)
3) Screw A (1/2” length) - QTY 2
Max. - 24-11/16” (62.7 cm)
4) Screw B (1 1/2” length) - QTY 4
Cutout Height N/A Min. - 16-3/4” (42.5 cm)
Max. - 17” (43.2 cm)
4) Screw B (1 3/4” length) - QTY 4 5) Screw C (3/8” length) - QTY 4 Cutout Depth N/A Min. 20” (50.8 cm)
Electrical Requirements 120VAC/60 Hz N/A N/A
Max. Amp Usage 1.65 KW; 13.5 amps N/A N/A
Approximate Shipping Wt. 55 lbs. (24.7 kg) 14 lbs. (6.5 kg) 15 lbs. (6.9 kg)
2 3
CABINET OR WALL CUTOUT CABINET INSTALLATION
Cutout Dimensions 1. Place the oven adjacent to the wall or cabinet opening. Plug the power cord into the electrical outlet.
Height (A)
Minimum 16 3/4” (42.5 cm) 2. Carefully guide the assembled oven into the prepared opening. Slide the oven on the Exhaust Duct Assembly. See
Maximum 17” (43.2 cm) Illustration 3. Avoid pinching the cord between the oven and the wall. Adjust the position of the oven so that the
Width (B) feet of the oven are fitted into the recesses of the Exhaust Duct Assembly. See Illustration 4.
Minimum 24 3/8” (61.9 cm)
Maximum 24 11/16” (62.7 cm)
Depth (C)
Illustration 4
Minimum 20” (50.8 cm)
ELECTRICAL OUTLET LOCATION Illustration 3
Outlet should NOT be in the shaded area as
indicated on Illustration 1
6”
(15.2 cm)
OVEN
NOTE 1: If the Depth (C) dimension is greater Foot
than 21” (53.3 cm), the outlet location may be in 4” SIDE
any area on the rear wall. (10.2 cm) Recess
NOTE 2: The floor of the opening should be
constructed of plywood strong enough to support
the weight of the oven and floor load Exhaust Duct Assembly
(approximately 100 pounds). The floor should be 4”
level for proper operation of the oven. Be sure to (10.2 cm)
check the local building code as it may require that
the opening be enclosed with side, ceiling and rear
partition. The proper functioning of the oven does FRAME INSTALLATION
not require the enclosure. VMTK ONLY
Illustration 1
EXHAUST DUCT ASSEMBLY
1. Place the Exhaust Duct in the opening. Position the FRAME ASSEMBLY to be square with the oven. Carefully place the FRAME ASSEMBLY on the oven.
When the Exhaust Duct Assembly is in the Illustration 2 Check that it is level and then secure with two SCREWS B. See Illustration 5. Secure the bottom portion of the FRAME
opening correctly, the flanges will be tightly ASSEMBLY with the two remaining SCREWS B. See Illustration 5.
against the lower edge of the opening. See
Illustration 2.
2. Secure the Exhaust Duct Assembly with the
two (1/2”) screws A. IMPORTANT: Secure Illustration 5
screws in outer hole.
Flanges Screw B
Screw B
Screw B
Exhaust Duct Assembly
Screw B
Screw A Detail A
4 5
DMTK270 ONLY DMTK300 ONLY OVER OVEN INSTALLATION
Position the BACK FRAME ASSEMBLY to be square with Position the BACK FRAME ASSEMBLY to be square with
the oven. Carefully place the BACK FRAME ASSEMBLY the oven. Carefully place the BACK FRAME ASSEMBLY
on the oven. Check that the oven is level and secure the on the oven. Check that the oven is level and secure the
lower portion FIRST with two of the Screw B. Adjusting upper portion FIRST with two of the Screw B. Secure the
the BACK FRAME ASSEMBLY up or down may be bottom portion of the BACK FRAME ASSEMBLY with the
necessary in order to locate the thru holes on the exhaust remaining two Screws B. See Illustration 5
duct assembly. Secure the upper portion of the BACK
FRAME ASSEMBLY with the remaining Screw B. See
Illustration 5
2” (5.1 cm) For 27” W. and 30” W. lower oven
4” (10.2 cm) For 36” W. lower oven
Illustration 5
Screw B
Place the FRONT FRAME ASSEMBLY through the microwave onto the BACK FRAME ASSEMBLY. Secure the FRONT
FRAME ASSEMBLY to the BACK FRAME ASSEMBLY with Screws C. See Illustration 6
NOTE: The center tab denotes correct orientation of the FRONT FRAME. See Detail B.
Illustration 6
Detail B
Screw C
6 7
