MBS2 THRU MBS10

Single Phase 0.8 AMPS. Glass Passivated Bridge Rectifiers

Voltage Range
200 to 1000 Volts
Current
0.8 Amperes
MBS
.193(4.90)
.177(4.50)
Features .033(0.84)
.022(0.56)

Ideal for printed circuit board .157(4.00)

Reliable low cost construction utilizing
.276(7.0)
.142(3.60) MAX

molded plastic technique

High surge current capability .102(2.60)
.087(2.20)

High temperature soldering guaranteed: .106(2.70) .053(1.53) .014(0.35)

260℃ / 10 seconds at 5 lbs., (2.3 kg ) .090(2.30) .037(0.95) .006(0.15)

tension

Small size, simple installation .008(0.20) .118(3.0)

Leads solderable per MIL-STD-202

MAX MAX .043(1.10) .083(2.12)
.028(0.70) .043(1.10)

Method 208 Dimensions in inches and (millimeters)

Maximum Ratings and Electrical Characteristics
Rating at 25℃ambient temperature unless otherwise specified.
Single phase, half wave, 60 Hz, resistive or inductive load.
For capacitive load, derate current by 20%
Type Number Symbol MBS2 MBS4 MBS6 MBS8 MBS10 Units
Maximum Recurrent Peak Reverse Voltage VRRM 200 400 600 800 1000 V
Maximum RMS Voltage VRMS 140 280 420 560 700 V
Maximum DC Blocking Voltage VDC 200 400 600 800 1000 V
Maximum Average Forward Rectified Current
On glass-epoxy P.C.B. I(AV) 0.5 A
On aluminum substrate 0.8
Peak Forward Surge Current, 8.3 ms Single
Half Sine-wave Superimposed on Rated Load IFSM 35 A
(JEDEC method )
Maximum Instantaneous Forward Voltage VF 1.0 V
@ 0.4A
Maximum DC Reverse Current @ TA=25℃ 5.0 uA
IR
at Rated DC Blocking Voltage @ TA=125℃ 100 uA
Typical Junction Capacitance Per Leg (Note1) Cj 13 pF
Typical Thermal Resistance Per Leg RθJA 85 ℃/W
Operating Temperature Range TJ -55 to +150 ℃
Storage Temperature Range TSTG -55 to +150 ℃
Note: 1. Measured at 1.0 MHZ and Applied Reverse Voltage of 4.0 Volts D.C.

- 616 -
 RATINGS AND CHARACTERISTIC CURVES (MBS2 THRU MBS10 )

FIG.1- DERATING CURVE FOR OUTPUT RECTIFIED FIG.2-MAXIMUM NON-REPETITIVE PEAK FORWARD
CURRENT SURGE CURRENT PER LEG
0.8 35
AVERAGE FORWARD RECTIFIED CURRENT. (A)

Ta=40 C
Aluminum Substrate

PEAK FORWARD SURGE CURRENT. (A)

0.7 30
Single Half Sine-Wave
(JEDEC Method)
0.6
25

0.5
Glass 20 F=50 Hz F=60 Hz
0.4
Epoxy
P.C.B
15
0.3

10
0.2

1 Cycle
0.1 Resistive or Inductive Load 5.0

0 0
0 20 40 60 80 100 120 140 160 1 10 100
O
AMBIENT TEMPERATURE. ( C) NUMBER OF CYCLES

FIG.3- TYPICAL FORWARD VOLTAGE FIG.4- TYPICAL REVERSE LEAKAGE

CHARACTERISTICS PER LEG CHARACTERISTICS PER LEG
10 100
INSTANTANEOUS REVERSE LEAKAGE CURRENT. (mA)
INSTANTANEOUS FORWARD CURRENT. (A)

Tj=150 0C 10 Tj=125 0C

1
Tj=25 0C
1

0.1
0.1

Tj=25 C
Pulse Width=300ms Tj=25 0C
1% Duty Cycle
0.01
0.01
0.2 0.4 0.6 0.8 1.0 1.2 1.4 0 20 40 60 80 100
INSTANTANEOUS FORWARD VOLTAGE. (V) PERCENT OF RATED PEAK REVERSE VOLTAGE. (%)

FIG.5- TYPICAL JUNCTION CAPACTITANCE

PER LEG
30

Tj=25 C
25
JUNCTION CAPACITANCE (pF)

f = 1 MHz
Vsig = 50mVp-p

20

15

10

5.0

0
0.1 1 10 100 200
REVERSE VOLTAGE. (V)

- 617 -
This datasheet has been download from:

[Link]

Datasheets for electronics components.