8 7 6 5 4 3 2 1
REVISIONS
NOTES: UNLESS OTHERWISE SPECIFIED
1. REFER TO PARTS LIST SECTION OF INSTALLATION INSTRUCTIONS FOR PART NUMBER REV. DESCRIPTION CHECKED DATE
REQUIRED. - RELEASED PER ECO 23771 J. WHITE 11/17/17
2. AUTOPILOT SHALL BE LOCATED IN THE PILOTS PRIMARY FIELD OF VIEW LATERALLY ±35° A REVISED PER ECO 23971 J. WHITE 5/17/18
AND VERTICALLY +25°. VERIFY THE PILOT CAN SEE ALL SWITCHES AND ARE WITHIN
REACH OF THE PILOT WITHOUT STRAINING.
D D
3. WHERE NO SUPPORT STRUCTURE IS PROVIDED, ATTACH .75 X .75 X .63 THK 2024-T3511
OR 6061-T6 ALUM EXTRUDED ANGLE TO FWD SIDE OF INSTRUMENT PANEL AND SECURE
TRAY AS SHOWN. SECURE ANGLE WITH A MINIMUM 2 EACH FASTENERS ABOVE AND
BELOW MOUNTING TRAY ASSEMBLY AND VERIFY INSTALLATION IS SECURE.
4. MAINTAIN A MINIMUM EDGE DISTANCE OF 2X THE HOLE DIAMETER WHEN DRILLING
ATTACHING HOLES IN EXISTING STRUCTURE AND BRACKETS.
5. LOCATE ALL NON DIMENSIONED PARTS APPROXIMATELY AS SHOWN. FASTENER
MINIMUM EDGE DISTANCE IS 2 TIMES FASTENER DIAMETER. MINIMUM PITCH DISTANCE
BETWEEN FASTENERS IS 4 TIMES FASTENER DIAMETER.
6. INSERT ONE SPACER AS REQUIRED ON EACH SIDE OF THE COMPUTER TRAY BETWEEN
THE TRAY AND THE EXISTING AVIONICS SUPPORT STRUCTURE, TO ELIMINATE ANY GAPS
THAT WOULD CAUSE DEFORMATION OF THE COMPUTER TRAY OR AVIONICS SUPPORT
STRUCTURE. DISCARD REMAINING SPACERS AS REQUIRED.
7. THE TRAY MUST BE PROPERLY BONDED TO THE AIRFRAME, REFERENCE INSTALLATION
INSTRUCTIONS FOR PROCESS.
C 8. ATTACH SIDES OF AUTOPILOT COMPUTER TRAY, NEAR THE BACK, TO EXISTING C
SUPPORT STRUCTURE. WHERE NO SUPPORT STRUCTURE IS PROVIDED, MANUFACTURE
SUPPORT TO SECURE A/P COMPUTER TRAY TO EXISTING COMPUTER MOUNTING
TRAY(S). MANUFACTURE SUPPORT FROM THE FOLLOWING MATERIAL(S): 5052-H32 / AMS-
4016 (AMS-QQ-A-250/8), 2024-T3 / AMS-QQ-A-250/4, OR 6061-T6 / AMS-QQ-A-250/11 AL
ALLOYS; .010 - .125 THK. ATTACH SUPPORT USING ANY COMBINATION OF: MS24693-S( )
SCREWS, AN960-6 WASHERS, NAS1149FN632P WASHERS, AN365-632 NUTS, MS21042-06
NUTS, MS20426AD( ) RIVETS, AND / OR MS20470AD( ) RIVETS AS REQUIRED PER INSTL.
PERMISSIBLE TO SHIM AS REQUIRED. FINAL DIMENSIONS OF SUPPORT STRAPS AND
SHIMS WILL BE DETERMINED BY AIRCRAFT INSTRUMENT PANEL CONFIGURATION. FINISH
ALL FABRICATED PARTS USING CHEM FILM PER MIL-C-5541, TYPE I, CLASS 1A, ALODINE.
9. PERMISSIBLE TO REPLACE ITEMS 8 AND 9 WITH MS21059 OR MS 21071-06 NUTPLATES.
10. FOR AUTOPILOT INSTALLATION, USE EXISTING INSTRUMENT PANEL CUTOUT. IF NO
CUTOUT IS EXISTING THEN REFERENCE VIEW B AS REQUIRED.
11. TOGGLE SWITCH PANEL CUTOUT IS FOR FULL INSTALLATIONS ONLY. FOR SYSTEM
CONVERSION, UTILIZE EXISTING TRIM AND AP MASTER SWITCHES.
12. ITEM 10 SCREWS USED TO MOUNT CONNECTOR TO ITEM 5 MOUNTING TRAY PLATE.
B B
REF 11 SEE NOTE 13 SWITCH, TOGGLE - - S-TEC
13. FOR SWITCH PART NUMBERS AND WIRING INFORMATION, REFERENCE PARTS LIST SCREW, 82° PHILLIPS FLAT HEAD, SELF
4 10 1111C400-6A - AN531-4R6 S-TEC
SECTION OF INSTALLATION INSTRUCTIONS AND WIRING INTERFACE DRAWING. TAPPING, STEEL
4 9 1201C6-031A WASHER, PLAIN, FLAT, STEEL (CAD) - NAS1149FN632P S-TEC
4 8 1406C632A NUT, NYLON, SELF-LOCKING, 6-32 - MS21044N06 S-TEC
SCREW, 100°, PFH, 6-32 X .50L, STEEL
4 7 1104C632-8A - MS24693-S28 S-TEC
(CAD PLATED)
6 6 1107S440-6 SCREW, PAN HD, 4-40 X 3/8 SS MS51957-15 S-TEC
PLATE, REAR, MOUNTING TRAY, AP-
1 5 59485-01 - S-TEC
2112
2 4 44636-02 SPACER, MOUNTING TRAY (.040 THK) - - S-TEC
2 3 44636-01 SPACER, MOUNTING TRAY (.032 THK) - - S-TEC
1 2 031028 MOUNTING TRAY ASSEMBLY - - S-TEC
1 1 SEE NOTE 1 DFCS COMPUTER - - S-TEC
QTY ITEM PART NUMBER DESCRIPTION S-TEC / MATL ALT PN / SPEC VENDOR / MFG
PARTS LIST
ACFT MODEL(S): INT. NEXT ASSY: THIRD ANGLE TOLERANCES
DRAWN
8/25/17
- PROJECTION (UNLESS OTHERWISE SPECIFIED) C. WHITWORTH One S-TEC Way
N/A +.006
HOLE: -.001 ENGINEER
8/25/17 Mineral Wells, TX A
A C. WHITWORTH
DECIMAL: .XXX: ±.010 APPROVED
DECIMAL: .XX: ±.03
S. JOSEPH 11/17/17 TITLE:
FORM (SWorks) 86359 REV -
DECIMAL: .X: ±.1
ALL SHEETS MAINTAIN THE SAME REVISION LEVEL.
ANGLES:
SURFACE
±1°
125
INSTALLATION, 01326
DIMENSIONING AND TOLERANCING
ROUGHNESS:
SHALL BE IAW ASME Y14.5M-1994. COMPUTER
EXPORT COMPLIANCE: TRANSFER OF S-TEC DATA (DOCUMENTS, SOFTWARE, DRAWINGS,
SPECS, ETC) BY ANY MEANS TO A FOREIGN PERSON OR ENTITY, WHETHER IN THE UNLESS OTHERWISE SPECIFIED
UNITED STATES OR ABROAD, MAY REQUIRE U.S. GOVERNMENT AUTHORIZATION. REMOVE ALL BURRS, ALL DIMENSIONS ARE IN INCHES,
BREAK SHARP EDGES SIZE CAGE CODE Drawing No.:
MILLIMETERS IN BRACKETS.
NOTICE: THE INFORMATION CONTAINED HEREIN IS CONFIDENTIAL AND PROPRIETARY R.015 MAX. INSIDE
INFORMATION, AND AS SUCH, CANNOT BE COPIED OR DISCLOSED TO OTHERS WITHOUT
THE PRIOR WRITTEN CONSENT OF THE S-TEC CORPORATION.
CORNER RADII .015 MAX.
DIMENSIONAL LIMITS APPLY B NA 761575
AFTER FINISH/PLATING. SCALE: 1:8 DO NOT SCALE DRAWING SHEET 1 OF 3
8 7 6 5 4 3 2 1
CWHITWORTH
8 7 6 5 4 3 2 1
REVISIONS
4X FOR REVISION HISTORY SEE SHEET 1
12 10
P2 CONNECTOR
2
D D
P1 CONNECTOR
2X 3
2X 4
C 5 C
1 6
6X
B B
7 9 8
4X 4X 4X
4X R.020
1.47
6.15
A A
VIEW B
FORM 86359 REV -
SIZE CAGE CODE SWorks Drawing No.: REV
B NA 761575 A
SCALE: 1:8 DO NOT SCALE DRAWING SHEET 2 OF 3
8 7 6 5 4 3 2 1
8 7 6 5 4 3 2 1
REVISIONS
FOR REVISION HISTORY SEE SHEET 1
D D
11 1.00
REF
11 13
2X .5000 THRU
C C
B B
A A
FORM 86359 REV -
SIZE CAGE CODE SWorks Drawing No.: REV
B NA 761575 A
SCALE: 1:1 DO NOT SCALE DRAWING SHEET 3 OF 3
8 7 6 5 4 3 2 1
