Model

STH
Series Combination
Soil Outfit
Instruction Manual
w
Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Multiple Sample Testing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Test Methods . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Available Nutrients . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Soil Sampling & Preparation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Test Procedure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
pH . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Extraction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Nitrate Nitrogen . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Potassium . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Phosphorus . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Humus . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Magnesium . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Calcium . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Sulfate . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Aluminum . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Chloride . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Ferric Iron . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Nitrite Nitrogen . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Ammonia Nitrogen . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
Manganese . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
Units of Measure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
Fertilizer Application Rates . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
Green Plant Tissue Tests . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
Soil Test Reagents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
n INTRODUCTION
This instruction manual is designed for use with the LaMotte STH professional
soil testing outfit. This manual also includes special instructions for testing
nitrate, phosphorus, and potassium in green plant tissues.
*Reagent is a potential health hazard. READ SDS:
lamotte.com. Emergency information:
Chem-Tel USA 1-800-255-3924
Int’l, call collect, 813-248-0585

Note: Some reagents in this kit are dispensed with screw-cap pipets that are
packaged separately.
Place the screw-cap glass pipets (0341) on the following reagents:

5156 *Phosphorus Reagent #2

5101 *Aluminum Test Solution
5140 *Magnesium Test Solution #1

Place the screw-cap plastic pipets (0392) on the following reagents:

5146 *Nitrate Reagent #1

5108PS *Calcium Test Solution
5171 *Sulfate Test Solution
5116PS *Ferric Iron Test Solution
5103PS *Ammonia Nitrogen Test Solution

4
n MULTIPLE SAMPLE TESTING
When extracts from two or more samples are being tested simultaneously use
separate pipets for each extract. Mixing samples will cause false test results.
Multiple test tubes, pipets, and spot plates have been provided to facilitate
proper analytical technique.

n TEST METHODS
Color chart methods are used for all tests except for Potassium. The reaction is
performed in a tube or on a spot plate and the resulting color is compared to a
laminated color chart.
The Potassium test measures the amount of turbidity in a sample relative to
the potassium content.

n AVAILABLE NUTRIENTS
All tests measure the portion of the nutrient in the soil that would be “available”
for the plant to use. Since extraction is not complete, the amount that is
measured is relative, dependent on the extraction procedure.

n SOIL SAMPLING & PREPARATION

Carefully follow the soil sampling procedures discussed in detail in the LaMotte
Soil Handbook (1504). For sampling greenhouse soils, the following specialized
procedure is recommended.
Collect greenhouse samples prior to watering. Remove any mulch covering
the soil, and then use a soil sampling tube or spoon to take a sample from
the entire plant rooting space, top to bottom. A composite sample insures
representative test results. Thoroughly mix 8 to 10 individual samples, and
then spread the composite sample on a sheet of paper or plastic to dry. Allow
the sample to air dry overnight. Do not oven dry the sample. Sift the dried
sample through a wire screen mesh similar to a window screen.

5
n TEST PROCEDURES
pH
pH is a measure of acidity or basicity. Soils can have a pH from 3.5 to 11.0,
but plants grow well in the range of 5.0 to 8.5. In soils with a low pH (acidic),
some nutrients can reach toxic levels and the activity of soil microbes is greatly
reduced. Soils with a high pH (alkaline) generally have a lower micro-nutrient
availability and some levels may be deficient.

PROCEDURE
1. Fill a test tube (0898) approximately one-third full of soil. Use the
Demineralizer Bottle (1155) to add demineralized water to the tube, until it
is filled to the 10 mL line. Cap and shake until the soil is well dispersed.
2. Add 5 drops of Soil Flocculating Reagent (5643WT). Cap and shake to mix.
Allow contents to settle before proceeding to Step 3.
3. Use a 1 mL pipet (0354) to transfer 1 mL of the clear solution above the
soil to one of the large depressions on a spot plate (0159). Transfer a
second 1 mL sample to the other large depression on the spot plate.
4. To the first sample on the spot plate, add two drops of *Duplex Indicator
(2221). Compare the resulting color reaction against the Duplex Color
Chart (1313).
5. The wide range pH test result indicates which narrow range indicator and
color chart should be selected to perform a more precise pH test. Choose
the narrow range indicator and appropriate chart with a mid-point that is
as close as possible to the value obtained in the wide range test.

Indicator pH Range Indicator Code Color Chart Code

Bromcresol Green 3.8-5.4 2207 1328
Chlorphenol Red 5.2-6.8 2209 1329
Bromthymol Blue 6.0-7.6 2210 1331
Phenol Red 6.8-8.4 2211 1332
Thymol Blue 8.0-9.6 2213 1335

Example: If the wide range test result is pH 6.0, choose the Chlorphenol Red
Indicator (2209) & the Chlorphenol Red Color Chart (1329) for Step 5.

6
6. Add two drops of the chosen narrow range indicator to the second sample
on the spot plate. Compare the resulting color reaction against the
appropriate color chart to obtain a precise soil pH reading.
Interpretation of pH Reading:
If the pH is: Then the soil is:
Below 5.5 Strongly Acid
5.5-6.0 Moderately Acid
6.1-7.0 Slightly Acid
Above 7.0 Alkaline

Extraction
The following extraction procedure uses Universal Extracting Solution
(5173PS) to produce a single soil extract which is used in each of the following
tests: nitrate nitrogen, ammonia nitrogen, nitrite nitrogen, phosphorus,
potassium, calcium, magnesium, sulfate, aluminum, iron, and manganese.
The pH, chloride, humus, and plant tissue tests use extraction procedures
described in the individual instructions for those tests.
The Extraction Tubes (0704) are marked at 7 and 14 mL. The instructions
below assume that a number of tests will be performed with the general soil
extract. Therefore 14 mL of extracting solution and eight level measures of the
soil sample are called for in Steps 1 & 2. If only a single test is to be performed
(e.g., nitrate nitrogen), fill the extraction tube to the 7 mL line (Step 1) and add
only four level measures of the soil sample (Step 2).

PROCEDURE
1. Fill an Extraction Tube (0704) to the 14 mL line with Universal Extracting
Solution (5173PS).
2. Use the 0.5 g spoon (0698) to add eight level measures of the soil sample.
Cap and shake for one minute.
Note: When adding samples with high concentrations of carbonates
to the Universal Extracting Solution (5173), swirl tube to mix for 30
seconds before capping to allow gases to escape.
3. Use a piece of filter paper (0465) and a plastic funnel (0459) to filter the
soil suspension into a second extraction tube (0704). (Fold the filter paper
in half and then in half again to form a cone which is fitted into the funnel.)
The filtrate in the second extraction tube is the general soil extract for use
in the 11 individual test procedures listed previously.

7
 Nitrate Nitrogen
The role of nitrogen in plant nutrition is discussed in the LaMotte Soil
Handbook. For interpretation of test results see the LaMotte Soil Handbook.

PROCEDURE
1. Use a 1 mL pipet (0354) to transfer 1 mL of the general soil extract to one
of the larger depressions on a spot plate (0159).
2. Add 10 drops of *Nitrate Reagent #1 (5146).
3. Use a 0.5 g spoon (0698) to add one level measure of *Nitrate Reagent 2
Powder (5147).
4. Stir thoroughly with a clean stirring rod (0519). Allow to stand five minutes
for full color development.
5. Match sample color with the Nitrate Nitrogen Color Chart (1315). Record
as pounds per acre nitrate nitrogen.

Potassium (Potash)
The role of potassium (potash) in plant nutrition is discussed in the LaMotte
Soil Handbook. For interpretation of test results, see the LaMotte Soil
Handbook.
When present in large amounts, ammonia salts will produce a precipitate
similar to that produced by potassium. If fertilizer containing ammonia
salts has recently been applied, or if the soil pH is below pH 5.0, perform the
Ammonia Nitrogen test (page 19) before performing the potassium test. A
high ammonia nitrogen test result will alert the operator to a probable false
high reading in the potassium test; actual potassium levels will be somewhat
lower.
It is important that the temperature of the test sample and the *Potassium
Reagent C (5162) be in the range of 20-27°C (68-80°F). On warm days, prior
to Step 3 below, cool both the test sample in the Potash “A” Tube and the
Reagent C container by placing them in cool water.

PROCEDURE
1. Use a transfer pipet (0364) to fill a Potash “A” Tube (0245) to the lower line
with the general soil extract.
2. Add one *Potassium B Tablet (5161A). Cap and shake until dissolved.

8
3. Add *Potassium Reagent C (5162) until the Potash “A” Tube is filled to the
upper line. Allow the *Potassium Reagent C (5162) to run slowly down the
side of the tube. Swirl the tube to mix. A precipitate will form if potassium
is present.
4. Stand the empty Potash “B” Tube (0246) on the Potassium Reading Plate
(1107), a rectangular piece of white plexiglass with a solid black line down
the middle. Place the tube directly over the black line.
5. Fill a transfer pipet (0364) with the test sample from the Potash “A” Tube.
6. Slowly add the test sample to the Potash “B” Tube, allowing it to run down
the side of the tube. Observe the black line down through the Potash “B”
Tube. Continue to add the test sample until the black line just disappears.
7. Record the value where the level of the liquid meets the scale printed on
the side of the Potash “B” Tube, as pounds per acre Available Potassium.
8. If the test result is equal to or greater than 400 pounds per acre, repeat
the test on a diluted test sample as follows:
A. Fill a Potash “C” Tube (0247) to the lower mark with the general
soil extract.
B. Add Universal Extracting Solution (5173) to the upper mark and
mix.
C. Using this diluted extract follow Steps 1 through 7 above. Multiply
the test result by 2 to obtain pounds per acre Available Potassium.

9
 Phosphorus
The role of phosphorus in plant nutrition is discussed in the LaMotte Soil
Handbook. For interpretation of test results see the LaMotte Soil Handbook.
The Phosphorus test is extremely sensitive. Special precautions should be
taken to prevent contamination. In particular, exposure of the test components
to fertilizer dust must be scrupulously avoided. The operator’s hands and
clothing, the work surface, and the testing area in general must be clean and
free of fertilizer residues.
LaMotte offers the Model NF Test Kit (Code 5090-01) for Phosphorus in
Alkaline Soils, to be used in place of the test described below when the soils are
predominantly alkaline (above pH 7.0).

PROCEDURE
1. Use a transfer pipet (0364) to fill a “Phosphorus B” Tube (0244) to the line
with the general soil extract.
2. Add 6 drops of *Phosphorus Reagent 2 (5156). Cap and shake to mix.
3. Add one Phosphorus Test Tablet (5706A). Cap and shake until dissolved.
4. Immediately compare the color that develops in the test tube against
the Phosphorus Color Chart (1312). Hold the tube about one inch in front
of the white surface in the center of the color chart. View the chart and
sample under natural light for optimum color comparison. The test result
is read in pounds per acre Available Phosphorus.

10
 Humus
Humus consists of the complex remains of fresh plant and animal residue
after extensive chemical and biological breakdown. Humus accounts for 60%
to 70% of the total organic carbon in soils. It can modify the physical properties
of a soil, strongly affecting its chemical and biological properties.

PROCEDURE
1. Use the 0.5 g spoon (0698) to add eight level measures of soil to a soil
extraction tube (0704).
2. Use the Demineralizer Bottle (1155) to fill the tube to the 14 mL line with
demineralized water. Cap and shake to mix.
3. Use a 0.5 g spoon (0698) to add two level measures of *Humus Screening
Reagent Powder (5119). If necessary, add more demineralized water to
return the level of the liquid to the 14 mL line. Cap and shake vigorously for
one minute.
4. Add 15 drops of Soil Flocculating Reagent (5643). Cap and mix gently.
Allow to settle for several minutes.
5. Use a piece of filter paper (0465) and a plastic funnel (0459) to filter the
mixture into a second extraction tube. (Fold filter paper in half and then in
half again to form a cone which is fitted into the funnel.)
6. Compare the clear filtrate in the second extraction tube with the Humus
Color Chart (1384).

Interpretation
The Humus color comparator is labeled with values of 1, 2, 3, 4, and 5. The
results are interpreted as follows:
Humus or Organic Matter in Soil
Humus Reading 1 2 3 4 5
Agricultural Soils Low Medium High
Garden Greenhouse Low Medium High
Soils
Organic Soils Low Medium High

11
 Magnesium
Magnesium is a constituent of chlorophyll, and chlorosis can result from
magnesium deficiency. Like calcium, magnesium cations play a role in base
or cation exchange. Magnesium is subject to more leaching than calcium.
Soils giving a low test reading should receive dolomitic lime or fertilizer which
contain considerable magnesia. Soils giving high magnesium tests and low
calcium tests should receive gypsum or high calcic lime, in order to restore the
calcium-magnesium balance.

PROCEDURE
1. Use a transfer pipet (0364) to transfer ten drops of the general soil extract
to one of the larger depressions on a spot plate (0159).
2. Add one drop of *Magnesium Test Solution 1 (5140). Stir with a clean rod
(0519). A pale yellow color will develop.
3. Add *Magnesium and Manganese Test Solution 2 (5145WT) one drop at a
time with stirring, until the pale yellow color changes to one of the darker
shades indicated on the Magnesium Color Chart (1306). About two drops
are usually required. Under some conditions, a precipitate will form shortly
after *Manganese-Magnesium Test Solution #2 has been added. This will
not effect the test reading. The test result is expressed in relative values
of Magnesium from very low to very high. For approximate corresponding
value in parts per million or pounds per acre, see page 19.

12
 Calcium
Calcium deficiency is seldom a direct limiting factor in plant growth, because
the lack of adequate calcium in a soil causes other growth limiting deficiencies
to occur first. Calcium is the dominant cation in a soil’s base or cation
exchange complex; it prevents excessive soil acidity and stimulates beneficial
biological activity. Low calcium levels may cause high soil acidity, diminishing
the availability of some nutrients (like nitrogen) and permitting toxic levels
of other minerals (like aluminum) to develop in the soil solution. In general,
calcium plays an essential role in maintaining the chemical equilibrium of the
soil solution.
This test measures the amount of calcium present in the base exchange
complex. Calcium test results confirm and supplement soil acidity readings.
Sandy soils normally contain less calcium than clay or organic soils. Sandy
soils should give readings of approximately 500 ppm, clay soils 1000 ppm, and
organic soils such as peats or forest loams 5000 ppm calcium. Lower levels
in clay or organic soils indicate that the active calcium has been replaced by
hydrogen or other ions, as in highly alkaline or highly acid soils.

PROCEDURE
1. Use a transfer pipet (0364) to transfer five drops of the general soil extract
to a flat-bottomed glass turbidity vial (0242).
2. Add one drop of *Calcium Test Solution (5108PS). Swirl gently to mix.
3. Match the milky turbidity of the test sample against the turbidity
standards on the Replaceable Calcium Chart (1303). Lay the chart flat
under natural light and hold the turbidity vial one-half inch above the
black strip in the middle of the chart. View the black strip down through
the turbid sample and compare the resulting shade of gray with the six
standard shades. The test result is read in parts per million replaceable
calcium.
4. If the test sample turbidity corresponds to or exceeds the lightest
standard (2800 ppm), repeat the test on a diluted sample. Transfer one
drop of the general extract to a clean turbidity vial and add four drops of
demineralized water. Then follow Steps 2 and 3 as above. Multiply the test
result by 5 to obtain parts per million replaceable calcium.

13
 Sulfate
Sulfur is essential to the formation of protein and affects various aspects
of plant metabolism. Sulfur-deficient plants are pale green in color with
thin, reedy stems. Negatively charged sulfate ions are easily leached. The
major sources of soil sulfate are fertilizer containing sulfate compounds and
atmospheric sulfur dioxide carried into the soil by precipitation.

PROCEDURE
1. Use a transfer pipet (0364) to transfer five drops of the general soil extract
to a flat-bottomed turbidity vial (0242).
2. Add one drop of *Sulfate Test Solution (5171). Swirl gently to mix.
3. Compare the turbidity of the sample to the turbidity standards of the
Sulfate Chart (1314). Lay the chart flat under natural light and hold the
turbidity vial one-half inch above the black strip in the middle of the chart.
View the black strip down through the turbid sample and compare the
resulting shade of gray with the six standard shades. The test result is read
in parts per million sulfate.

Aluminum
All soils contain significant amounts of aluminum in inorganic colloidal
material and in the form of undecomposed minerals. In neutral, slightly
alkaline, or slightly acid soils, this aluminum is in inert combinations that do
not affect plant growth. In more acidic soils, aluminum can form soluble salts
toxic to plant growth. A high test result indicates an undesirable acid soil.
Plants which normally thrive on acid soils may fail on a soil with a high active
aluminum test reading. A medium test result is generally tolerable—especially
for grasses, corn, oats, potatoes, and tobacco. A low or negative aluminum test
result is preferable.

PROCEDURE
1. Use a transfer pipet (0364) to transfer two drops of the general soil
extract to one of the larger depressions on a spot plate (0159).
2. Add two drops of Universal Extracting Solution (5173).
3. Add one drop of *Aluminum Test Solution (5101).
4. Stir with a clean stirring rod (0519). Allow to stand for one minute.
5. Match the resulting color with the Active Aluminum Color Chart (1301).
The test result is expressed in relative values of active aluminum from very
low to very high. For approximate corresponding values in parts per million
or pounds per acre, see page 19.
14
 Chloride
Chlorides are present in practically all soils. Application of fertilizer may
increase chloride levels. Chlorides are removed from the soil by leaching.
Excessive concentrations are toxic to plants. A high test reading, particularly
where stunted growth has been observed, may indicate poisoning due to high
chloride levels in the soil.

PROCEDURE
1. Use the Demineralizer Bottle (1155) to fill a tube (0970-S) to the 5 mL line
with demineralized water.
2. Use the 0.5 g spoon (0698) to add four level measures of the soil sample
to the tube. Cap and shake vigorously for 2-3 minutes.
3. Use a piece of filter paper (0465) and a plastic funnel (0459) to filter the
mixture into a second tube (0970-S). (Fold filter paper in half and then in
half again to form a cone which is fitted into the funnel.)
4. Use a transfer pipet (0364) to transfer five drops of the filtrate in the
second tube to a flat-bottomed turbidity vial (0242).
5. Add one drop of *Chloride Test Solution (5111) to the vial. Swirl gently to
mix.
6. Match the turbidity or amount of precipitation against the turbidity
standards on the Chloride Chart (1304). Lay the chart flat under natural
light and hold the turbidity vial one-half inch above the black strip in the
middle of the chart. View the black strip down through the turbid sample
and compare the resulting shade of gray with the six standard shades. The
test result is read in parts per million chloride.

15
 Ferric Iron
The role of iron in plant nutrition is discussed in the LaMotte Soil Handbook.
Iron is essential to the formation of chlorophyll, and iron deficiency causes
chlorosis. While most soils contain abundant iron, only a fraction is soluble
and readily available to the growing plant. This is particularly true in neutral or
alkaline soils. Acid soils contain higher levels of available iron.

PROCEDURE
1. Use a transfer pipet (0364) to transfer four drops of the general soil
extract to one of the larger depressions on a spot plate (0159).
2. Use the 0.05 g spoon (0696) to add one level measure of *Iron Reagent
Powder (5275). Mix with a clean stirring rod (0519).
3. Add one drop of *Ferric Iron Test Solution (5116PS). Mix again.
4. Match the resulting color to the Ferric Iron Color Chart (1348). The test
result is read in pounds per acre ferric iron.

Nitrite Nitrogen
Nitrites are formed as an intermediate step in the production of nitrates.
Soils that are well drained and aerated contain only small amounts of nitrite
nitrogen. Excessive nitrites, which are toxic to plants, may result from soil
conditions unfavorable to the formation of nitrate, such as inadequate
aeration. High nitrite readings may also be encountered in soils with large
amounts of nitrates, where a portion of the nitrate nitrogen decomposes to
form nitrites.

PROCEDURE
1. Use a transfer pipet (0364) to add 5 drops of soil extract to a large
depression on a spot plate (0159).
2. Add 1 drop of *Nitrite Nitrogen Reagent 1 (5151WT).
3. Add 1 drop of *Nitrite Nitrogen Reagent 2 (5152WT). Mix with a clean
stirring rod.
4. Add 3 drops of *Nitrite Nitrogen Reagent 3 (5153WT). Mix with a stirring
rod. Wait 1 minute.
5. Match sample color to a color standard on the Nitrite Nitrogen Color Chart
(1310). Record as ppm nitrite nitrogen.

16
6. If sample color matches, or is deeper than, the highest standard, repeat
test on a diluted sample. Transfer one drop of soil extract to a large
depression on a spot plate. Add 4 drops of *Universal Extracting Solution
(5173). Follow Steps 2-5. Multiply final result by 5. Record as ppm Nitrite
Nitrogen.

Ammonia Nitrogen
A fertile soil may be expected to give a low ammonia nitrogen test reading,
unless there has been a recent application of nitrogenous fertilizer in forms
other than the nitrate. The rapid disappearance of ammonia after fertilizer
application indicates the desired transformation of the ammonia to the
more available nitrate compounds. In forest soils ammonia is the most
abundant available form of nitrogen. If there is a satisfactory rate of nitrogen
transformation, the humus layers of a forest soil will produce very high
concentrations of ammonia nitrogen.

PROCEDURE
1. Use a transfer pipet (0364) to transfer four drops of the general soil
extract to one of the larger depressions on a spot plate (0159).
2. Add one drop of *Ammonia Nitrogen Test Solution (5103PS). Stir with a
clean stirring rod (0519). Allow to stand for one minute.
3. Compare the resulting color against the Ammonia Nitrogen Color Chart
(1302). The test result is expressed in relative values of ammonia nitrogen
from very low to very high. For approximate corresponding values in parts
per million or pounds per acre, see page 19.

17
 Manganese
An essential element in the enzyme system of plants, manganese plays a role
in metabolic reactions affecting germination, photosynthesis, and other vital
aspects of plant development. Yellowing and stunted growth results from
manganese deficiency. Some insoluble manganese is present in all soils. Its
solubility or availability is closely related to soil pH. Calcareous soils or soils
which have been heavily limed may be deficient in available manganese.
Application of a soluble manganese salt, such as manganese sulfate, will
correct this problem. Conversely, toxic levels of available manganese may
develop in highly acid soils; this condition may be corrected by liming. Since
available manganese may be leached from the soil or altered to less active
forms by oxidation, this test should be conducted just prior to planting
and during plant growth. Any positive test reading, even a very low reading,
generally indicates the presence of sufficient available manganese to meet
plant requirements. A high test reading is undesirable and indicates a need for
liming.

PROCEDURE
1. Use a transfer pipet (0364) to add 10 drops of soil extract to the large
depression on a spot plate (0159).
2. Use the 0.05 g spoon (0696) to add one measure of Manganese Buffer
Reagent (6310). Mix with a clean stirring rod (0519) until the powder
dissolves.
3. Use the other 0.05 g spoon (0696) to add one measure of *Manganese
Periodate Reagent (6311). Mix with a clean stirring rod for 20 seconds.
Note: The *Manganese Periodate Reagent will not dissolve completely.
4. Match the color in the spot plate to a color standard on the Manganese in
Soil Color Chart (1307-01). Record as ppm Manganese.
Note: Immediately clean the spot plate to prevent staining.

18
n UNITS OF MEASURE
Test results are expressed in the following terms:
Relative Amounts from
Parts per Million (ppm) Pounds Per Acre (lb/acre) Very Low to Very High
Nitrite Nitrogen Nitrate Nitrogen Ammonia Nitrogen
Calcium Phosphorus Magnesium
Sulfate Potassium Aluminum
Chloride Iron Manganese
Pounds per acre represent the number of pounds of soil in an acre to the
plough depth of 6-7 inches, or 2,000,000 lbs. Conversion from pounds per
acre to parts per million, or vice versa, may be accomplished by means of the
following formulas:
ppm x 2 = lb/acre

lb/acre x 0.5 = ppm

In the four nutrient tests which produce relative test results, the following
approximate quantitative values may be assigned to the relative terms:
Approximate Value Expressed in ppm
Low
Very
Low (Medium Very
Test Factor (Low) Low) Medium High High
Ammonia Nitrogen 5 10 40 100 150
Magnesium 5 10 25 80 150
Aluminum 5 10 30 80 125
Manganese NA 5 12 25 40

n FERTILIZER APPLICATION RATES

When interpreting soil test results to establish a fertilizer program, a number
of variables must be considered in addition to the values obtained in the soil
tests. These variables include the composition of the soil, drainage, climate,
previous fertilizer programs and soil test results, and the type of plant to be
grown. Consult local agricultural services for guidelines to fertilizer application
rates for the specific soils in your area.

19
n GREEN PLANT TISSUE TESTS
Testing an extract prepared from fresh plant tissue provides a means of
verifying suspected nutrient deficiencies during plant growth. Plant tissue
testing is discussed in the LaMotte Soil Handbook. The necessary information
for testing nitrate nitrogen, phosphorus, and potassium in green plant tissues
is given below.
These tests are meant to be used in a comparative manner. It is important
to test tissue from healthy plants as well as those from problem plants.
Interpretations should be based on comparison of test results from plants
of the same species and same age, grown in the same general environment.
Since test reactions may vary from species to species, at different stages of
growth, or under different growing conditions, it is not possible to accurately
quantify test results. The color charts should be used in a comparative manner.
Relative values from very deficient to abundant have been assigned to the
range of possible test reactions under each factor below.

PREPARATION of TISSUE EXTRACT

1. Select a small lot of the leaf petioles or succulent portion of the stem.
When testing problem plants, collect tissue from those areas where the
abnormality is most observable.
2. Use a clean, sharp knife or a razor blade to cut the material into fine bits
not more than 1/8” to 1/16” in length and thickness.
3. Fill an Extraction Tube (0704) to the 7 mL line with this material. Do not
pack down.
4. Add *Universal Extracting Solution (5173PS) to the upper line. Cap and
shake vigorously for five minutes.
5. Use a piece of filter paper (0465) and a plastic funnel (0459), filter the
mixture into a second Extraction Tube (0704). This filtrate is the tissue
extract to be used in place of the general soil extract in the nitrate
nitrogen, phosphorus, and potassium test procedures.

20
PLANT TISSUE TEST PROCEDURE
Follow the soil test procedures for nitrate nitrogen, phosphorus, and
potassium, using the tissue extract in place of the general soil extract.
Remember that the color charts should only be used in a comparative manner,
along with the relative values suggested. The most meaningful test results
will be obtained from the comparison of healthy plant and problem plant test
reactions.
Guidelines for Interpreting Plant Tissue Tests
Relative Amount of Nutrient
Test Factor Test Reaction in Plant Tissue
Nitrate Nitrogen Dark Pink Color Abundant
Light Pink Color Adequate
Colorless No Reserve/Probably
Deficient
Phosphorus Deep Blue Color Abundant
Light Blue Color Adequate
Yellow to Colorless Low to Deficient
Potassium Heavy Precipitate Adequate to Abundant
Medium Precipitate Low to Deficient
Trace Precipitate Deficient
No Precipitate Very Deficient

21
n SOIL TEST REAGENTS
This information is provided to enable the soil analyst to correlate LaMotte soil
test results with results obtained using other soil test procedures.

Soil Extraction Procedure The Universal Extracting Solution (5173) is

composed of sodium acetate which has been adjusted to a pH of 4.8
with acetic acid. This solution extracts the soluble nutrients, such as
phosphorus and nitrogen, as well as soluble and exchangeable potassium
and other cations, such as calcium and magnesium.

Potassium Test The Potassium test is based on the fact that potassium
salts give a yellow crystalline precipitate with sodium cobaltinitrite,
*Potassium B Tablets (5161A). *Potassium Reagent C (5162) is
denatured ethyl alcohol which facilitates the formation of the precipitate
in more or less colloidal form.

Phosphorus Test Phosphates react with ammonium molybdate,

*Phosphorus Reagent 2 (5156), to produce salts of a complex ammonium
phosphomolybdate, which produce the blue molybdenum oxide color
when reduced. Phosphorus Test Tablets (5706A), the reducing agent, are
stannous chloride.

Nitrate Test The Nitrate test is based on the so-called Denige’s test
in which two dye intermediates are coupled in the di-azo reaction to
form a color dyestuff. The nitrite required in this reaction is supplied by
reduction of the nitrate in the soil extract. *Nitrate Reagent #1 (5146) is
a solution of potassium acid sulfate. *Nitrate Reagent #2 Powder (5147)
is a mixture of the two intermediates, N(1-naphthyl)-ethylene-diamine
dihydrochloride and sulfanilamide; the reducing agent, which is zinc dust;
and the filler, which is barium sulfate.

Humus Test In the humus test the disodium salt of ethylene diamine
tetraacetic acid, *Humus Screening Reagent Powder (5119), extracts
the dark colored humus fraction from the soil. This is measured against
a special color comparator which has been calibrated to give a general
relationship between this color and the content of organic matter.

Soil pH Test Sensitive short range pH indicators are used to measure the
pH of a distilled water soil extract. Barium Sulfate is used to accelerate
settling of the soil water mixture.

Calcium Test *Calcium Test Solution (5108PS) is sodium oxalate, which reacts
with calcium to form a precipitate of Calcium Oxalate.

22
Ammonia Nitrogen Test *Ammonia Nitrogen Test Solution (5103PS) is
Nessler’s Reagent.
Magnesium Test The dye Titian Yellow, *Magnesium Test Solution 1
(5140), is absorbed on the precipitated magnesium hydroxide which is
formed when *Magnesium and Manganese Test Solution #2 (5145WT),
sodium hydroxide is added. The degree of color in the test reaction
depends on the amount of precipitate formed.

Manganese Test Manganese is oxidized by the *Manganese Periodate

Reagent (6311) to form permanganate.

Aluminum Test *Aluminum Test Solution (5101) is an alcoholic solution

of hematein.

Nitrite Nitrogen Test *Nitrite Nitrogen Reagent 1 (5151WT) is

hydrochloric acid. *Nitrite Nitrogen Reagent 2 (5152WT) is Lombard’s
Solution, which consists of sulfanilic acid, ammonium chloride, and
phenol. *Nitrite Nitrogen Reagent 3 (5153WT) is sodium hydroxide.
A yellow dye is formed when nitrite is present.

Ferric Iron Test *Ferric Iron Test Solution (5116PS) is potassium

thiocyanate, which reacts with iron to give the colored ferric thiocyanate.

Sulfate Test *Sulfate Test Solution (5171) is barium chloride, which

reacts with sulfate to form the precipitate, barium sulfate.

Chloride Test Deionized water is used as the extracting solution.

*Chloride Test Solution (5111) is silver nitrate, which reacts to form the
precipitate, silver chloride.

23
 Helping People Solve Analytical Challenges

802 Washington Avenue • Chestertown • Maryland • 21620 • USA

800-344-3100 • +1 410-778-3100 (Outside USA) • Fax 410-778-6394
Visit us on the web at www.lamotte.com
©2023 LaMotte Company, All Rights Reserved 36070 10.23.2023