TEMPERATURE BASED FAN SPEED
& COOLING, MONITORING USING TIVA
LAUNCHPAD (TM4C123GXL)
Project Accociates:
➢Naveen kumar
➢Aditya karanwal
➢Mukul kumar
objective of project
• Our objective of making this project is for reducing the power
consumption. And also to assist people who are disabled and are
unable to control the speed of fan.
• It may also be used for monitoring changes in environment.
• In near future, it can also be used in different
industries and electronic devices.
contents :
• INTRODUCTION
• BLOCK DIAGRAM
• HARDWARE EQIPMENTS
• MICROCONTROLLER TIVA LAUNCHPAD (TM4C123GXL)
• DHT11 (TEMPERATURE SENSOR)
• NOKIA LCD DISPLAY
• DC MOTER
• MOTOR DRIVER (CIRCUIT DIAGRAM)
• JUMPER WIRES
• APPLICATION
• ADVANTAGES
• FUTURE SCOPE
INTRODUCTION
A simple introduction about the temperature controller circuit.
This circuit project is mainly used for indicating temperature,
controlling temperature.
In temperature control circuit, there are two parts consisting of
DHT11 sensor interface with TIVA LAUNCHPAD.
NOKIA LCD display interface with TIVA LAUNCHPAD.
Hardware equipment
• TIVA MICROCONTROLLER (TM4C123GXL)
• DHT11 TEMPERATURE SENSOR
• NOKIA 5110 LCD DISPLAY
• DC MOTOR
• MOTOR DRIVER L293D
CONNECTION
NOKIA 5110 LCD
MICROCONTROLLER
DHT11 SENSOR (TM4C123GXL) DISPLAY
MOTOR
DRIVER
FAN L293D
MICROCONTROLLER TIVA
LAUNCHPAD(TM4C123GXL)
The Tiva-C (TM4C123GXL) LaunchPads
are inexpensive self-contained, single-board
microcontrollers, about the size of a credit
card, featuring an ARM Cortex-M4F 32-bit
CPU operating at 80 to 120 MHz.
DHT11 TEMPERATURE
SENSOR
The DHT11 is a basic, ultra low-cost digital
temperature and humidity sensor.
It uses a capacitive humidity sensor and a
thermistor to measure the surrounding air
and spits out a digital signal on the data pin
(no analog input pins needed).
It's fairly simple to use but requires careful
timing to grab data.
NOKIA 5110 LCD DISPLAY
Nokia 5110 LCD Display Module is a low-
cost monochrome LCD module comprised
of 84 X 48 pixels that can be used to display
rich graphics and text content.
This module is a revision that accepts 3-5V
input. So no extra level shifter is needed. It
uses the TM4C123GXL controller, which is
the same used in the Nokia 3310 LCD.
DC MOTER
5 Volts standard voltage required by chips
and drives in a computer.
The power supply converts 120v alternating
current (AC) into 5 volts of direct current
(DC), as well as 3.3v and 12v.
MOTOR DRIVER L293D
This L293D IC allows DC motor to drive on
either direction. L293D is a 16-pin IC which
can control a set of DC motors
simultaneously in any direction.
At room temperature:
APPLICATIONS
• A Personal computers.
• Exhaust fans in large hotels.
• Washing machines.
• CD and DVD players.
• The circuit can be used for Car Engine to reduce the heat.
• This project can be used in Home.This project can be used in
Industry.
• This will help in saving the energy / electricity
ADVANTAGES
• It is very economical and easy to handle by the user.
• Speed varies automatically, so that it controls the speed
without using it manually.
• It is help full to disabled People.It is very easy to install in
offices, houses, etc.
• Save energy by slowing down its speed in low
temperature
FUTURE SCOPE
• The project will concentrate on electric standing fan
rather than other type of fan such as ceiling fan.
• We can monitor more parameters like humidity, light
and at the same time control them.
• We can send this data to a remote location using mobile
or internet.
Project video:
THANK YOU
