DEPARTMENT OF PROSTHODONTICS AND CROWN & BRIDGE
FINAL YEAR
SECTION-A
LONG NOTE(2*8)
1. Define “ PATH OF INSERTION” and “PATH OF REMOVAL” in a removal cast
partial denture. Discuss the factors affecting the same and the role played by the
surveyor?
2. What are jaw relation? Discuss the biological significance of following during the
complete denture preparation?
SHORT NOTE(3*3)
1. Richmond crown
2. Relining and Rebasing
3. Selective grinding
MCQ (TOTAL-10 MARKS)
1. There are many landmarks in the oral cavity which helps in the designing complete
dentures. One of the important landmarks is fovea palatini. What is its relations to the
vibrating line?
a) Behind the vibrating line
b) In front of vibrating line
c) On the vibrating line
d) Has no relations to vibrating line
2.A patient presents for provision of complete dentures. Examination reveals an
unfavorable ridge slope. What is the most likely reason?
a) He has recent extraction
b) He has edentulous for a long time
c) Unfavorable ridges are never seen
d) Submerged tooth may be present
[Link] primary denture support area for a mandibular complete denture is?
a) The vestibule
b) The buccal shelf
c) The palatopharyngeal fold
d) All the above
4. There are many impression techniques which are used in recording impressions of the
edentulous areas. Which impression techniques will be used in a patient with a sharp
mandibular ridge?
a) Minimum pressure impression techniques
b) Selective pressure impression techniques
c) Excessive pressure impression technique
d) All the above of impression techniques
5. A loss in vertical dimension in complete denture will cause mandible to move?
a) Backward in relation to upper jaw
b) Forward in relation to upper jaw
c) No change in the position
d) In eccentric movements
6. While recording the rest postion of the mandible , the patient’s?
a) Heads should be upright and unsupported
b) Heads should be supported by the head set
c) The neck should be extended
d) Head can be any position
7. After the provision of complete denture the first review appointment for evaluating the
new dentures should be carried out after?
a) 3 hours after the delivery
b) 12 hours after the delivery
c) 24 hours after the delivery
d) 48 hours after the delivery
8. The average root surface area of the maxillaryfirst molar is(in mm2)?
a) 133
b) 233
c) 333
d) 433
9. Male component of pier abutment is placed on?
a) Mesial side of pontic
b) Distal side of pontic
c) Mesial side of the abutment
d) Distal side of the abutment
[Link] movement is better resisted by a tooth preparation if?
a) Diameter is smaller
b) Diameter is larger
c) Diameter is large and length is small
d) Do not depend upon the diameter of tooth
SECTION-B
LONG NOTE (2*8)
1. Discuss in details the fixed partial failures?
2. Define facebow? Discuss the different types of pontic?
SHORT NOTE(3*3)
1. Pier abutment
2. Implant biomaterials
3. Neutral zone
MCQ(TOTAL-10MARKS)
1. Extra retention in abutment teeth is obtained with?
a) Dovetail
b) Slots, pins and grooves
c) Outline form
d) Increasing tooth reduction
2. Ante’s law provides an aid for?
a) Selection of pontic
b) Selection of connector
c) Selection of retainers
d) Selection of abutments
3. The distance between the implant and the superior aspect of the inferior alveolar canal
should be?
a) 1mm
b) 3mm
c) 2mm
d) 4mm
4. Which is an appropriate procedure for disinfection of alginate impression?
a) Placing under running water
b) Spraying with gluteraldehyde and sealing in a bag for 10 min
c) Complete immersion in bleach in a plactic bag for 1hour
d) Placing it in autoclave
5. Which elastomer have longest working and setting time?
a) Polyether
b) Polysulfide
c) Condensation silicones
d) Addition silicons
6. The position of the upper occlusal rim in the articulator is adjusted by
a. Arbitrary means
b. By using facebow
c. By incisal pin
d. By adjusting intercondylar distance
7. For implant placement, ideal amount of bone under soft tissue is?
a) 8mm vertical and 4mm horizontal
b) 10mm vertical and 6mm horizontal
c) 12mm vertical and 6mm horizontal
d) 14mm vertical and 8mm horizontal
8. What is the suitable material for making impression pf partial dentate patient would
be?
a) Irreversible hydrocolloids
b) Reversible hydrocollids
c) Elastomers
d) Plaster of paris
9. Cavosurface margin angulation in chamfer finish line is?
a) Always 90 degrees
b) 90 degree or less than 90 degrees
c) 90 degree or more than 90 degrees
d) 120 degrees
10. The taper that should be present in a prepared tooth as abutment for FPD?
a) 10 degrees
b) 6 degrees
c) 2 degrees
d) 4 degrees
