HAND TACHOMETER MANUAL TM-5000/5010/E HAND TACHOMETER MANUAL TM-5000/5010/E

HAND TACHOMETER INSTRUCTION MANUAL Please note that misuse of this device 3. Measurement [Link]
In-contact Adaptor A t t e n t io n may lead to injury to the user or 1) Press the measurement button to turn the unit on, the LCD will then light up. When storing this device, please avoid areas which are very humid, exposed
damage to the device. to direct sunlight, high temperature, subject to vibration, dust, dirt, saline,
(Only while the measurement button is pressed, measurement is performed)
or organic gases.
Remote Sensor 2) To measure, press the measurement button for at least 1 second.
3) When measuring using the reflective tape, the " " mark will appear confirming
TM-5000/5010/E TM-5013 TM-4015 Customer Service that the photosensor is working. SPECIFICATIONS (MAIN UNIT)
4) If the measurement is out of range, the "----" mark will appear.

LINE SEIKI CO., LTD. TM-5000 TM-5010/E

Model
Thank you for purchasing our hand tachometer. [Link]-contact type measurement 6.0 - 99999.9 rpm
Please read this instruction manual carefully before using to Address: 37-7 Chuo-cho, 2-Chome 0.10 - 1666.66 rps
1) The distance between reflective tape and tachometer main unit (or remote sensor)
Meguro-ku, Tokyo 152-0001 Japan 0.60 - 9999.99 m/min
ensure the correct usage of this device. Contact : Tel: +81-50-1741-6630 Fax: +81-3-37104552 is 5 to 30 cm. and the angle of incidence of the light is within +/- 30 degrees. Measuring
6.0 - 99999.9 rpm 1.00 -16666.6 cm/s
Please keep this instruction manual for future reference. E-mail : webtrade@[Link] 2) Press the measurement button, confirm that the " " mark is displayed on the Range 0.39 - 6561.65 inch/s
Web : [Link] screen, then read the rotational speed. 1.9 - 32808.3 f/min
3) When the measurement button is released, the display is held for about 3 mins. 0.65 - 10936.1 y/min
The unit automatically turns off after 3 mins. of inactivity.
[Link] type measurement Resolution 0.1 rpm 0.1 rpm fpm, others 0.01
Safety P reca u tio n s 1. Preparations 1) Use the rubber tip correctly by touching it perpendicular to the center of the axle +_ 0.01% +_ 1 digit rpm m/min
of the rotating object under test. To measure the peripheral speed of the items Accuracy (for other units, the conversion accuracy is +_ 0.05% +_ 1 digit)
1. Installing the batteries
For safe usage of this device, please observe all statements regarding such as belts, replace the rubber tip with the surface speed wheel.
precautions and warnings in this instruction manual. 1) Press and slide down the battery cover at the back side of the main unit. 2) To attach the surface speed wheel, pull out the rubber tip with your hand and press Sampling Time 1.0 - 10.0 seconds
2) Install the four batteries (AAA 1.5V) noting the polarity as indicated inside. the surface speed wheel axle so that the boss of the wheel axle is inserted into
3) After installing the batteries, replace and slide back the cover. the slit of the adaptor axle. Pull the surface speed wheel gently to confirm that Display : 6 digits, 7 segment LCD
Attention 2. Using the reflective tape (for non-contact type) it does not come off. Battery alarm : mark
3) When measuring the circumferential velocity, the surface speed wheel should touch Reflective light : mark
Do not use this device near machines that emit strong Cut off a length of 1 to 3 cm. of the reflective tape. Remove the kraft paper Display
the measured object so that the surface speed wheel turns in parallel with it. Display unit: r/min, r/s, m/min, cm/s
electromagnetic fields or objects that store static electricity. backing and stick the reflective tape on the object whose rotational speed is to be Display unit : r/min
3. Auto-power off y/min, inch/s, f/min
Do not drop this device or submit it to strong impact. measured.
After the measurement button is released, the display is held for about 3 minutes Memory display: MAX, MIN, MEM1~8
Do not use or store the device where it can be exposed to Wipe off oils or stains from the surface where the reflective tape will be attached.
direct sunlight, dust, high temperature and high humidity. Stick the reflective tape as near as possible to the outer edge of the object whose then the unit automatically turns OFF if no further measurements are made during After 3 mins. from last measurement or key operation
Auto Power-off
Inspect the device before conducting measurements. rotational speed is to be measured. that time. (Applicable for both TM-5000 and TM-5010/E)
Use the battery case to ensure that the battery is properly
installed.
3. Installing the In-contact Adaptor (for contact type) * Note
Make sure that lights coming from a stroboscope and/or fluorescent lights do not
Data Hold Time
Measurement data: until the next data is defined
Memory data: same as battery life
Remove the battery when the device will not be used for a Loosen the lock screw at the back of the unit, insert the in-contact adaptor to the reach the photoelectric part and reflective tape attached to the rotating object to
upper side of the main unit and tighten the lock screw using a screw driver. Use a Measuring Non-contact measurement using the main unit or with remote sensor (use with reflective tape)
long period of time. prevent measurement errors. Before starting rotation of the object under test,
coin if a screw driver is not available. The lock screw must be tightened securely Method Contact measurement using the in-contact adaptor (use with rubber tip, surface speed wheel)
Do not attempt to disassemble or modify this device. please confirm that the measurement on the reflective tape is 0.0 rpm. If the
to ensure that the in-contact adaptor does not fly off while in use. measurement is affected by external light, change the position of the unit. Measuring 50 - 300mm(using reflective tape)
Distance
4. Installing the remote sensor 4. Functions
Set the switch in the battery compartment to off position. Insert the connector of 1. Changing of Measurement Units (TM-5010/E only) Power Supply 4 pcs. of AAA alkaline battery(continuous measurement of 20 hrs.)
the remote sensor to the modular telephone style connector on the left hand side.
Changing of rotational speed units to peripheral speed units can be done by Operating
5 - 40 °C Non-Freezing
pressing the Rotational/Peripheral Units Group selection key. Temperature
[Link] and Functions Pressing the Unit Selection key changes the units of rotational speed or peripheral Storage
speed into other units of measurement. -10 - +60 °C Non-Freezing
Temperature
After the installation of batteries, the default unit is r/min which will be displayed on
Storage
the screen. 35 - 85%RH Non-Condensing
Rubber Tip Surface speed wheel (circumference 1/10 m or 1/10 y) Humidity
Combination of adaptor with TM-5000 or TM-5010 is available. 2. Maximum / Minimum Values (TM-5010/E only)
Dimension/ 122(H) x 58(46)(W) x 28(D)mm / approx. 130g (including batteries)
For TM-5000, display is 1/10 m/min. Pressing the Measurement Mode switch will change the data displayed on the Weight
For TM-5010/E, calculations are done internally to display screen. "MAX" display represents the maximum value and "MIN" represents the
the units m/min, cm/sec, f/min, inch/sec and y/min,
minimum value.
Remote Sensor
which can be read directly.
The maximum and minimum values are values measured from the start of
MODELS
In-contact adaptor measurement until the measurement button is released. TM-5000 main unit
In-contact measurement or surface speed measurement is possible using the Pressing the measurement button clears the previous maximum and minimum AAA alkaline battery, 4 pcs.
rubber tip or the surface speed wheel in combination with TM-5000 or TM-5010. measurement values. TM-5000 Reflective tape, 10 pcs.
Attention! Instruction manual
When using at high speed, be very careful that the portion being measured don't get dragged on. 3. Memory (TM-5010/E only)
TM-5010/E main unit
By pressing the 8 point memory data input key, the measured values and unit can
AAA alkaline battery, 4 pcs.
Photoelectric part
be stored in the 8 point memory. At each press of the 8 point memory data input TM-5010/E Reflective tape, 10 pcs.
key, data are stored accordingly into No. 1 to No. 8. MEM and the current memory
Unit display Instruction manual
No. is displayed on the screen. After memory No. 8 is displayed, no additional
Memory number display data can be inputted. In-contact adaptor
TM-5013
r/min cm/s m/min r/s r/min
MAX MEM

Photoelectric detector indicator rotational speed mode Pressing the 8 point memory data read/clear key will recall the stored data. While Rubber tip, 3 pcs.
MIN

(r/min r/s) the data are being called, MEM will blink and the memory no. is displayed on the Surface speed wheel (1/10 m)
Measurement display
linear speed mode screen. When the data from a memory no. is called out and the 8 point memory In-contact adaptor
Measurement button
While it is pressed, measurement is performed. (m/min cm/s y/min inch/s f/min) read/clear key is pressed, ALLCLR will be displayed on the screen. When TM-5014 Rubber tip, 3 pcs.
Connector for remote sensor probe Rotational / Linear speed ALLCLR is displayed on the screen, pressing the 8 point memory data input key Surface speed wheel (1/10 y)
Units Group selection key will clear the memory and the display will return to the measured value.
Remote sensor
MEAS

Measurement mode switch When the memory is being recalled and ALLCLR is displayed, not pressing any TM-4015
MAX MIN

By pressing this button, display changes as follows: (21mm diameter, maximum cable length 1m)
key for 20 seconds will return the display to the measured value.
.../min

Measurement value > MAX value > MIN value .../s Unit selection key
Connector for remote sensor probe 8-point memory data CALL
r/min r/s 5. Battery Replacement
input key RoHS
TM-5000 CLR TM-5010
The remote sensor can be used by m/min cm/s y/min
turning the slide switch inside the battery
LINE SEIKI
8-point memory data LINE SEIKI
When the mark at the left portion of the screen starts to blink, please replace
read/clear key the batteries.
box located at the back of this unit. f/min inch/s This device conforms to the following EMC regulations:
Please refer to '1.1 Installing the Batteries' for the battery replacement procedure.
TM-5000 TM-5010 Please replace all batteries with new ones.
EMI : EN50081-1
Be careful not to mix different types of batteries - i.e. manganese batteries and
EMS : EN50082-1
alkaline batteries together. Test was performed without using the remote sensor.
* The instrument cannot measure accurately after low battery indicator is This manual was last revised Dec. 8, 2022.
displayed. Please replace the battery immediately. *Subject to change without prior notice.
All Rights Reserved,Copyright © 2022,LINE SEIKI CO.,LTD.