CONSTRUCTION OF GIRLS HOSTEL FOR THE LIAQUAT

UNIVERSITY OF MEDICIAL & HEALTH SCIENCE

JAMSHORO, SINDH

GIRLS HOSTEL (COVERED AREA = 31373 SFT)

BILL OF QUANTITIES
APRIL 2024

Head Office: Office # B-6, 2nd Floor, Masood Arcade, IJP Road, Islamabad.
Tel:051 4848375, Fax: 0514848375, E-mail: [email protected]
Regional Office: 287-A, Street # 6, Cavalry Ground, Lahore. Tel: 042 37250130
 CONSTRUCTION OF GIRLS HOSTEL FOR THE LIAQUAT UNIVERSITY OF MEDICIAL & HEALTH
SCIENCE JAMSHORO,SINDH
(COVERED AREA = 31019 Sft)

BILL OF QUANTITIES
Rates Based on Composite Schedule of Rate (GENERAL-2012) Sindh

Sr. No. DESCRIPTION AMOUNT

1. CIVIL WORKS

a Cost of Schedule Items 55,177,481

b Add/ Deduct _________ % above/ below on Scheduled Items

c Cost of Non-Schedule Items

TOTAL OF CIVIL WORKS-A

2. PUBLIC HEALTH WORKS

a Cost of Schedule Items 1,517,461

b Add/ Deduct _________ % above/ below on Scheduled Items

c Cost of Non-Schedule Items

TOTAL OF PHE WORKS -B

3. ELECTRICAL WORKS

a Cost of Schedule Items 5,774,179

b Add/ Deduct _________ % above/ below on Scheduled Items

c Cost of Non-Schedule Items

TOTAL OF ELECTRICAL WORKS-C

TOTAL (A+B+C)

5% SST

GRAND TOTAL WITH SST

Amount in Words:

___________ _______
Contractor Client
 CONSTRUCTION OF GIRLS HOSTEL FOR THE LIAQUAT UNIVERSITY OF MEDICIAL & HEALTH SCIENCE
JAMSHORO,SINDH
(COVERED AREA = 31019 Sft)

BILL OF QUANTITIES
CIVIL WORKS
Rates Based on Composite Schedule of Rate (GENERAL-2012) Sindh

Sr.
Item No. Description Unit Qty Rate Amount
No.
1 C-1/18(b) Excavation in foundation of Building Bridges and other
structures including dagbelling dressing,refilling around
structrure with excavated earth Watering and ramming lead
upto 5 ft in Ordinary Soil. %0Cft 26518.00 3176.25 84,227.79
2 C-1/19 Cutting hard rock such as granite, ballast, hard lime stone or
sand stone etc. with chisels and hammers for small foundations.

%0Cft 23458.70 28672.05 672,609

3 C-18/92 Providing Anti -termmite treatment by spraying /sprinkling
/spreading Neptachlar 0.5% Emulsion as an overall pre -
construction treatment in slab type construction under the slab
and along attached perches or entrances etc, complete as per
directions of Engineer Incharge. P.Sft 48714.14 9.74 474,475.71
4 C-4/5(i) Cement concrete plain including placing compacting, finishing
and curing, complete (including screening and washing at stone
aggregate without for all shuttering.(Mix 1:4:8)
%Cft 2748.63 11288.75 310,286.22
5 R.C work in roof slab, beams columns rafts, lintels and other
structural members laid in situ or precast laid in position
complete in all respects (I) Ratio (1 : 2: 4 ) 90 Lbs.cement 2 Cft.
Sand 4 Cft. Shingle 1/8" to 1/4" gauge .(Foundation, Beams,
Slabs, Stairs )
(i) C-4/6 a-i Ground Floor
P.Cft 20375.47 337.00 6,866,534
(ii) C-4/6 a-i +6 (d) First Floor

P.Cft 10623.81 349.10 3,708,771

(iii) C-4/6 a-i +6 (d) Second Floor

P.Cft 2550.68 361.20 921,307

6 Reinforced cement concrete in roof slab, beams, columns
lintels, girders and other structural members laid in situ or
precast laid in position, or prestressed members cast in situ,
complete in all respects:- Type B (nominal mix 1: 1.5: 3)
Columns
(i) C-4/6 a-ii Ground Floor

P.Cft 7024.32 349.00 2,451,489

(ii) C-4/6 a-ii +6 (d) First Floor

P.Cft 3548.12 361.10 1,281,227

(iii) C-4/6 a-ii +6 (d) Second Floor

P.Cft 230.52 373.20 86,029

7 C-5/4-I(e) Pacca brick work in foundation and plinth in cement sand mortar
1:6. %Cft 20702.91 11948.36 2,473,658.44
8 C-1/21 Filling, watering and ramming earth in floors with surplus earth
from foundation lead upto one chain and lift upto 5 feet. %0Cft 16658.90 1512.50 25,196.58
9 C-5/5-I(d) Pacca brick work in Ground Floor cement, sand mortar Ratio
1:5 %Cft 13844.45 12902.08 1,786,222.18
10 C-5/5-I(c) Pacca brick work in Ground Floor cement, sand mortar Ratio
1:4 %Cft 2680.50 13227.41 354,560.90
11 C-5/5-I(d) + 6 Pacca brick work in First Floor cement, sand mortar Ratio 1:5
%Cft 13698.33 13340.71 1,827,454.31
Sr.
Item No. Description Unit Qty Rate Amount
No.
12 C-5/5-I(c) + 6 Pacca brick work in First Floor cement, sand mortar Ratio 1:4
%Cft 2176.04 13666.04 297,378.84
13 C-5/5-I(d) + 6 Pacca brick work in Second Floor cement, sand mortar Ratio
1:5 %Cft 252.00 13915.46 35,066.96
14 Cement plaster 1:6 upto 12' height:- b) 1/2'' thick.
Ground Floor
(i) C-9/12(b) Ground Floor
%Sft 63527.33 2206.60 1,401,794
(ii) C-9/12(b)+29 First Floor

%Sft 57403.73 2347.57 1,347,593

(iii) C-9/12(b)+29 Second Floor

%Sft 9858.00 2488.54 245,320

15 Cement plaster 1:4 upto 12' height:- b) 3/8" thick.
Ground Floor

(i) C-9/11(a) Ground Floor

%Sft 62423.08 2197.52 1,371,760
(ii) C-9/11(a) +29 First Floor
%Sft 56448.23 2338.49 1,320,036
(iii) C-9/11(a) +29 Second Floor
%Sft 9858.00 2479.46 244,425
16 C-9/40.A Preparing the surface and painting with plastic emulsion paint of
+ approved make I/c rubbing the surface with sand Paper, filling
40-B the voids with chalk / plaster of paris and then painting etc.
complete. Three Coats
%Sft 123291.66 2237.95 2,759,205.75
17 C-9/(38.A+38.B) Preparing the surface and painting with weather coat I/c
rubbing the surface with rubbing brick / sand Paper, filling the
voids with chalk/ plaster of Paris and then painting with weather
coat of approved make.:- three coats %Sft 37662.81 2567.95 967,162.00
18 C-4/5(i) Cement concrete plain including placing compacting, finishing
and curing, comlete (including screening and washing at stone
aggregate without for all shuttering.(Mix 1:4:8) %Cft 9197.58 11288.75 1,038,291.53
19 C-4/5(f) Cement concrete plain including placing compacting, finishing
and curing, comlete (including screening and washing at stone
aggregate without for all shuttering.(Mix 1:2:4)
%Cft 4238.87 14429.25 611,636.53
20 C-8/16-c Providing and laying 2" thick topping cement concrete (1:2:4 )
including Surface finishing and dividiing into panels: %Sft 3351.50 3275.50 109,778.38
21 C-8/16-a +C-8/18 Providing and laying 3" thick topping cement concrete (1:2:4 )
including Surface finishing and dividiing into panels: (Roof)
%Sft 15483.75 4638.70 718,244.71
22 C-8/16-a Providing and laying 1" thick topping cement concrete (1:2:4 )
including Surface finishing and dividiing into panels:(a) 1" thick
Ground Floor. (Mosaic) %Sft 13079.50 1915.13 250,489.43
23 C-8/55 Laying mosaic topping 1/2" thick in pannels of approved any
pattern of one part of white cement to two parts of marble chips
of required shade and size and of approved pigment in the ratio
of 1: 12 of cement used in topping including rubbing and
polishing etc. complete. Ground Floor %Sft 13079.50 12316.49 1,610,935.31
24 C-8/41 Mosaic dado or skirting one part of grey cement and 2 parts of
marble chips laid ovver 1/2" thick cement plaster 1:3 complete
with finishing.Ground Floor %Sft 1232.27 11174.93 137,705.25
25 C-8/16-a Providing and laying 1" thick topping cement concrete (1:2:4 )
+ including Surface finishing and dividiing into panels:(a) 1" thick
C-8/18 First Floor. (Mosaic Floor) %Sft 13375.37 2142.01 286,501.76
26 C-8/55 Laying mosaic topping 1/2" thick in pannels of approved any
+ pattern of one part of white cement to two parts of marble chips
C-8/18 of required shade and size and of approved pigment in the ratio
of 1: 12 of cement used in topping including rubbing and
polishing etc. complete. First Floor
%Sft 13375.37 12543.37 1,677,722.15
27 C-8/41 + Mossaic dado or skirting one apart of white cement and two
C-8/18 parts of marble chips laid over 1/2" thick plaster 1:3 complete
with finishing 1/2"thick. First Floor %Sft 1140.40 11401.81 130,025.96
Sr.
Item No. Description Unit Qty Rate Amount
No.
28 C-7/18 Khuras on roof 2'x2'x6" (600 x 600 x 150 mm)
Each 20.00 358.68 7,173.60
29 C-10/21 Providing and fixing, approved quality mortice lock.
Each 76.00 1786.13 135,745.88
30 C-11/5-(c) Preparing surface and painting of doors and windows any type,
(including edges).Three Coats.
%Sft 140.00 2116.41 2,962.97
31 C-18/83(a) Supplying & fixing in position Aluminium channels framing for
hinged doors or Alcop made with 5 mm thick tinted glass glazing
(Belgium) and Alpha (Japan) locks I/c handles, stoppers etc. (a)
Deluxe model (White) P.Sft 252.00 1450.76 365,591.52
32 C-17/24 Making & fixing steel grated door with 1/16" thick sheeting
including angle iron frame 2" x 2" 3/8"and 3/4" square bars 4"
centre to centre with locking arrangemtent. P.Sft 70.00 726.72 50,870.40
33 C-18/84(a) Supplying & fixing in position Aluminium channels framing for
slidding windows & ventilators of Alcop made with 5 mm thick
tinted glass glazing (Belgium) & Aluminium fly screen I/c
handles stoppers & locking arrangement etc. complete. (a)
Deluxe model (White). P.Sft 3558.82 1592.69 5,668,097.03
34 C-9/34 Extra labour rate for making grooves of 1" x 1/4" or 3/4" x 1/2"
plastered surface with true edges both vertically and horizontly
with uniform depth and, with groove base smoothly finished etc.
complete as per instruction of Engineer Incharge. P.Rft 10751.00 7.71 82,890.21
35 C-10/24 Providing and fixing deodar wooden wardrobe including boxing
with back shelves , shutters drawers and brass fittings such as
handles locking arranjgement, hanger rod shoe rod and mirror
measuring 2' x 1' Complete as per approved design.
P.Sft 3726.00 2364.63 8,810,611
36 C-11/9 Bitumen coating to plastered or cement concrete surface.
(Two Coat)
%Sft 2630.89 778.09 20,470.70
37 C-8/22 1 1/2" thick mosaic flooring consisting of 1/2" mosaic topping of
one part of grey cement to two part of marble chips laid over
1"thick flooring of 1:2:4 cement concrete including rubbing and
polishing complete. (O.H.W.T) %Sft 422.50 9258.67 39,118
38 C-8/39(b) Mosaic dado or skirting one part of grey cement and 2 parts of
marble chips laid ovver 1/2" thick cement plaster 1:3 complete
with finishing.(O.H.W.T)
%Sft 303.55 10580.93 32,118
39 C-18/88 Providing & fixing Aluminium sheet 6" to 9" with V-Notch for
expansion joints I/c fixing with nails / screws.
P.Rft 224.00 207.51 46,482.24
40 C-Publich Health Providing "expansion joint" in concrete work of 9'' wide
Part B/J/Page-56 corugated PVC water stop (with bulb) i.c soldering cost of
material and labour etc complete. P.Rft 78.00 86.00 6,708
41 C-Publich Health Providing C.I Manhole Cover & Frame i/c cost of Material etc.
Part B/J/Page-35 P.Kg 168.00 140.00 23,520
Total of SOR Items 55,177,481.02
 CONSTRUCTION OF GIRLS HOSTEL FOR THE LIAQUAT UNIVERSITY OF MEDICIAL & HEALTH SCIENCE
JAMSHORO,SINDH
(COVERED AREA = 31019 Sft)

BILL OF QUANTITIES

CIVIL WORKS
Non-Scheduled Items

Sr.
Item No. Description Unit Qty Rate Amount
No.
1 NSI Providing and laying hard grade ribbed deformed (minimum
yield point 60,000 psi) reinforcement bars of all sizes with &
including the cost of straightening, cutting, bending laying in
position, making joints, wastage,overlaps, steel chairs, etc.
including the cost of binding wire and labor charges for binding
of steel reinforcement overlaps other than those shown on
drawings, steel chairs, precast chairs, removal of rust from bars
placing in position on cement concrete complete in all respect
Amreli Steel, Agha Steel, Razaque Steel or equivalent approved
by engineer incharge. P.Kg 205395.50
2 NSI Providing and laying sweat earth with new earth excavated from
outside including watering ramming compacting in layers up to
12'' thick etc completed as directed by engineer Incharge
including 15 km carriage etc. P.Cft 56015.85
3 NSI Supplying laying River sand or pit sand of approved quarry and
levelling dressing, watering ramming and compacting by manual
compactor method etc complete. %Cft 6070.40
4 NSI Providing and laying Ceramic Matt Tiles Texture Light color for
flooring size 12"x18”x3/8" laid over 3/4" thick cement sand
mortar (1:2) i/c filling joints in white cement and matching
pigment i/c cutting charges complete in all respect as approved
& directed by the Engineer/ Incharge. (Shabbir Tile, Master or
Equivalent)
P.Sft 1566.74
5 NSI Providing and laying Ceramic Tiles Texture Light color for
skirting / dado size 12"x18”x3/8" laid over 3/4" thick cement
sand mortar (1:2) i/c filling joints in white cement and matching
pigment i/c cutting charges complete in all respect as approved
& directed by the Engineer/ Incharge. (Shabbir Tiles, Master or
Equivalent)
P.Sft 4852.75
6 NSI Providing and fixing 3/4" thick China Verona full width area
above 2 Sft laid in white cement matching pigment 3/4" thick
cement sand mortar (1:2) i/c filling joints in white cement &
matching pigment, making gola on exposed edges complete in
all respect as approved by the Engineer/ Incharge.(Stairs,
Podium, Planter and Vanity) P.Sft 2211.16
7 NSI Providing and fixing steel Fire Rated Emergency Exit Door
,Door manufactured as per NFPA 252 & UL 10C standards
Steel Door (MS) Size: 60" x 98" Double Leaf door, Filled with
fire-rated material With Inner Steel Stiffeners for
reinforcement.Door Leaf 1.2-1.5mm, Door Frame 1.5- 2.0mm,
Accessories: Hinges, Panic Bar On single Leaf, SS Handle,
Glass 12x24 ft, and Door closer on single Leaf. complete in all
respect as approved & directed by the Engineer/ Incharge.
(TECHNO (PVT) LTD or Equivalent) Each 2.00
Sr.
Item No. Description Unit Qty Rate Amount
No.
8 NSI P/F 1-1/2" thick solid flush door comprising of 2.5 mm thick
Commercial ply compressed over 2.5 mm thick commercial ply
over 1" thick packing wood in style and rails under proper
pressure i/c french polish Master, Happy or Equivalent Brand
the cost of nails, sliding bolt, tower bolt , handles, glue, sawing
charges, Painting charges, sand papering and 3/8" thick
matching wooden lipping as approved and directed by the
Engineer Incharge. P.Sft 1722.00
9 NSI Providing and fixing M.S. grill fabricated with MS Square
polished Vertical/horizontal Bars of specified size @ 4" c/c '
passed through punched holes in MS Patti of 1-1/4"x1/8" i/c the
cost of 1-1/4"x1/8'' MS patti for Frame of windows and painting
Master, Happy or Equivalent 3 coat complete in all respect as
approved and directed by the Engineer Incharge. (ii) 1/2"
Square Bars P.Sft 3558.82
10 NSI Providing and fixing PVC Doors 38mm thickness i/c deluex
matching color PVC frame matt or glossy finish having color
(white-Gray-Marble Gray-Oak Wood- Dard Oak Wood, Coffee
Wood Honey Pine Wood-Mahagony-Marry Gold-Chocolate
Brown-Honey Dew) i/c all accessories i/c mortice locks
complete in all respect as approval by the Engineer Incharge.
P.Sft 337.75
11 NSI Providing and fixing Steel Sheet (Jisti) hollow press frame of
doors, etc. (Chowkhat only) of 16 SWG welded with M.S. flat
6"x1½"x1/8" (150x40x3mm) M.S. hold fast 9"x1"x1/8"
(225x25x3mm) welded/ screwed 4" (100mm) long iron hinges
including fitting chowkhat with cement sand mortar 1:8 and
embedding hold fast in cement concrete 1:2:, Single Rebate,
10" wide, including of Master, Happy or Equilant Paint of 3
Coats complete in all respect as per direction of Engineer in-
P.Sft 1808.10
charge.
12 NSI Providing and fixing 2'-9" high stair railing comprising of non
magnetic (304) Stain less steel 2" dia pipe railing of 18 SWG
welded with vertical posts of 2" dia stainless steel round/ Squar
pipe/ Tong (chimta) @ 2-ft c/c fixed on alternate steps with 3"
long steel screws and brass rawal plugs , 3-Nos diagonal
stainless steel pipes of 1/2" dia passes through goties fixed on
vertical post, i/c stainles steel welding, fixing & polishing
complete in all respects as approved and directed by the
Engineer Incharge
P.Rft 941.50
13 NSI Providing and fixing 12mm thick tempered glass partition with
frameless door ghani or equivalent with aluminium U/channel of
approved texture/ shade, thickness 2 mm with silicone i/c the
cost of holding the partitions, door closer machine, S.S handle
18" & all hardware complete in all respect as per
specifications/standard as per instruction of Engineer Incahrge.
P.Sft 793.13
14 NSI Providing and fixing auotomatic hydraulic operated door closer
imported heavy duty complete in all respect as approved and
directed by the Engineer Incharge. Each 76.00
15 NSI Providing and applying of 2 coat of Acrylic Re-enforced
Cementitious water proofing & Protective Coating (ConFlex 515)
Complete in all respects. P.Sft 7320.60
16 NSI Providing and fixing thermopore (foamed polythene) sheet in
horizontal and vertical expansion joints. (a) 1-1/2" (40 mm) thick
thermopore sheet. P.Sft 1932.00
17 NSI Providing and fixing stainless steel mesh of 16 guage fixed with
nails for concrete and bricks joint complete in all respect and as
approved and directed by the Engineer Incharge. P.Sft 5500.00

Total of Non SOR Items

 CONSTRUCTION OF GIRLS HOSTEL FOR THE LIAQUAT UNIVERSITY OF MEDICIAL & HEALTH SCIENCE
JAMSHORO,SIND
(COVERED AREA = 31019 Sft)

BILL OF QUANTITIES
PUBLIC HEALTH WORKS
Rates Based on Composite Schedule of Rate (GENERAL-2012) Sindh
Sr.
Item No. Description Unit Qty Rate Amount
No.
SANITARY FIXTURES AND FITTINGS
Providing and fixing European type white glazed earthen
ware wash down W.C. pan complete with and I/c the cost of
white/black plastic seat (Best quality) and lid with C.P.brass
SOR(Water hineges and buffers, 3 gallons white glazed earthen ware low
supply & level foushing cistern with siphon fitting 1-1/2" dia white
1
Sewerage porcelain enamelled fluish bend 3/4" dia and making requiste
(Ch 1/5) number of holes in walls, plinth and floor for pipe
connections and making good in cement concrete 1:2:4.
(ICL or Equivalent)
Each 3.00 11,477.40 34,432.20
Providing and Fixing squating type white glazed earthen
ware w.c pan with front fresh inlet & complete with including
the cost of flushing cistern with internal fitting and flush pipe
SOR(Water with bend and making requisite number of holes in walls
supply & plinth & floor for pipe connection and making good in cement
2
Sewerage concrete 1:2:4. (A) W.C pan 23" & low level earthen ware
(Ch 1/2-A ii) flush tank 3 gallons. (ii) with 4" dia white glazed earthen ware
trap and plastic thumble. (Foriegn Quality)
Each 10.00 5,772.80 57,728.00
Providing and fixing steel sinks stainless local make
complete with cast iron or wraught iron brackets 6 inches
SOR(Water built in wall, 1-1/2" c.p bubber plug chrome plated brass
supply & chain, 1-1/2" c.p brass waste, with 1-1/2" P.V.C. waste pipe
3
Sewerage & making requiste number of holes in wall, plinth & floor for
(Ch 1/19-c) pipe connection & making good in cement concrete 1:2:4. (c)
Steel sink stainless sized 33" x 18" local make (Standard
pattern) (Master or Equivalent)
Each 3.00 5,712.30 17,136.90
SOR(Water Providing and fixing CP Muslim shower with double bib cock
supply & & ring pipe etc complete.
4
Sewerage
(Ch 6/19 (a) Each 12.00 3,432.00 41,184.00
SOR(Water Providing and fixing soap tray earthen ware with c.p screws
supply & etc.complete.
5
Sewerage
(Ch 2/5) Each 20.00 497.20 9,944.00
SOR(Water Providing and fixing chrome plated brass towel rail complete
supply & with brackets fixing with 1" long c.p brass screws. (iii) Towel
6
Sewerage Rail 24" long (b) 3/4" dia round or square (Superior Quality)
(Ch 2/1 (iii-b) Each 12.00 1,082.95 12,995.40
Providing and fixing c,p brass toilet paper holder of standard
SOR(Water
size with chrome plated brass brackets complete (Similar to
supply &
7 twyfords design No 1108) (b) Superior Quality
Sewerage
(Ch 2/2 (b)
Each 12.00 1,071.40 12,856.80
SOR(Water Providing and fixing (½") dia, lead connection complete with
supply & a (½") dia brass stop cock, two brass nuts & lining jointed to
8
Sewerage lead pipe with plumber wiped solder joints (½" lead pipe to
(Ch 1/22) be of not less than 4lbs per lineal yard. Each 105.00 689.70 72,418.50
Sr.
Item No. Description Unit Qty Rate Amount
No.
Providing and fixing 6" x 4" C.C gully trap with 4" oulet
SOR(Water complete with 4" thick 1:2:4 C.C for bed & 1/2" thick cement
supply & plaster (1:3) to the karb. C.I grating 6" x 6' C.I cover and
9
Sewerage frame 12" x 12" (inside) etc complete. Earthan ware glazed
(Ch 10/1 (i) Gully trap 6" x 6" x 4" with C.I cover & Frame.
Each 5.00 1,220.67 6,103.35
Providing and laying R.C.C. pipe & collors of class "B" and
SOR (PHE fixing in trench i/c cutting,fitting and jointing with maxphalt
10 works) Part-B composition and cement mortar (1:1) i/e. testing with water
(II) A-2 to a head of 22.5 meter or 76 ft. (e) 300mm (12") i/d P.Rft 550.00 543.75 299,062.50
Excavation for pipeline in trechches, and pits in soft soils i/c
trimming and dressing sides to true allignment and shape
levelling of beds of trenches to correct level and grade,
SOR (PHE cutting joint and holes and disposal of surplus earth within a
11 works) Part-B one chain as directed by engineer incharge.Providing fence
(III) A-1 guards, lights, flags and temperory crossings for non-
vehicular traffic where ever required lift upto 5ft. (1.52 m) and
lead upto one chain (30.5 m).
1000 Cft 4,950.00 3,600.00 17,820.00
Earth work compaction (Soft, ordinary or hard soil). (d)
12 Ch/1/13 (d) Ramming earth work (All types of soil). 1000 Cft 4,950.00 453.75 2,246.06
Rehandling of earth work. (a) Lead upto a single throw of
Kassi, Phawrah or a = Shovel.
13 Ch/1/9 (a)

1000 Cft 4,950.00 756.25 3,743.44

SOR(Water Providing and fixing full way gun metal peet/gate valve with
supply & wheels, threaded or flabged ends with rubber washing. (iv)
14
Sewerage 1-1/4" (Light pattern)
(Ch 6/4 (iv) Each 6.00 337.92 2,027.52
SOR(Water Providing and fixing full way gun metal peet/gate valve with
supply & wheels, threaded or flabged ends with rubber washing. (v)
15
Sewerage 1-1/2" (Light pattern)
(Ch 6/4 (v) Each 6.00 695.42 4,172.52
MANHOLE
SOR (PHE Constructing manhole or inspection chamber for the required
works) P-1 diameter of circular sewer and 3'-6" (1067 mm) depth waith
walls of BB in cement sand mortar 1:3 cement plastered 1:3,
1/2" thick. Inside of walls and 1" (25 mm) thick over
benching and channel i/c fixing C.I manhole cover with frame
16 of clear opening 1-1/2' x 1-1/2' (457 x 457mm) of 1.75 cwt.
(88.9 Kg) embaded in plain C.C 1:2:4 and fixing 1"(25mm)
dia MS steps 6" (150 mm) wide projecting 4" (102mm) from
the face of wall at 12" (305mm) C/C duly painted etc.
Complete as per Standard specification and drawing.
Job 13.00 14,748.00 191,724.00
Providing & fixing 22"x 16" lavatory basin in white glazed
earthen ware complete with & i/c the cost of W.I or C.I
cantilever brackets 6 inches built into walls, painted white in
SOR (Water
2 coats after a primary coat of red lead paint, a pair of 1/2"
supply &
rubber plug & chrome brass waste of approved pattern 1-
17 Sanitary
1/4" dia malloable iron or CP brass trap, malloable iron or
works) Ch 1-
brass unions and making requisite number of holes in walls
13
plinth and floor for pipe connection &making good in cement
concrete 1:2:4 (Foreign or Equivalant)
Each 22.00 6,237.00 137,214.00
Providing and fixing 6" x 2" or 6" x 3" C.I floor trap of the
SOR (Water
approved selt cleaning design with a C.I screwed down
supply &
gratting without a vent arm complete with & i/c making
18 Sanitary
requisite number of holes in walls, plinth & floor for pipe
works) Ch 1-
connections & makinggood cement concrete 1:2:4.
20
Each 62.00 2,042.43 126,630.66
Sr.
Item No. Description Unit Qty Rate Amount
No.
SOR (Water Providing and fixing 24"x 18" bavelled edge mirror of belgium
supply & glass complete with 1/8' thick hard board and c.p screws
19 Sanitary fixed to wooden pleat. ( Standard Pattern)
works) Ch 1-
26 (b) Sft 160.00 2,376.00 380,160.00
VALVES
20 SOR (Water Providing and fixing handle valves (China) 16bars or
supply & equivalent complete in all respects as approved by the
Sanitary engineer incharge.
works) Ch 6-5

ii 3/4 inch Each 14.00 271.92 3,806.88

i 1/2 inch Each 10.00 200.42 2,004.20

21 SOR (Water Providing, fixing and testing PPRC ball valve 32mm , (with
supply & unsoldered copper ball) made to B.B.S 1212.
Sanitary
works) Ch 6-6
(iv) Each 4.00 510.84 2,043.36
22 SOR (Water Providing, fixing and testing PPRC ball valve 40mm , (with
supply & unsoldered copper ball) made to B.B.S 1212.
Sanitary
works) Ch 6-6
(v) Each 4.00 573.70 2,294.80
23 SOR (Water Providing G.I Pipes,specials, and clamps etc. including fixing
supply & cutting & fitting complete with and I/c the cost of breaking
Sanitary through walls and roof, making good etc. Painting two coats
works) Ch 4-1 after cleaning the pipe etc. with white zink paint with pigment
to match the color of the building and testing with water to a
pressure head of 200 feet and handling.

v 1-1/2" dia G.I pipe Rft 150.00 188.97 28,345.50

vi 2" dia G.I pipe Rft 110.00 233.00 25,630.00
Providing and installing P.V.C. strainers `B' class of
SOR (PHE
approved design quality and make including necessary
24 works) Part-B
sockets and solvent, etc. complete: 3" (80 mm)
(II) (O-9 (a))
Rft 80.00 166.35 13,308.00
Supplying & fixing M.S bail plug.
SOR (PHE
25 works) Part-B
(II) (O-8 (b))
Each 4.00 2,607.00 10,428.00

Total of SOR ITEMS 1,517,460.59

 CONSTRUCTION OF GIRLS HOSTEL FOR THE LIAQUAT UNIVERSITY OF MEDICIAL & HEALTH SCIENCE
JAMSHORO,SIND
(COVERED AREA = 31019 Sft)

BILL OF QUANTITIES
PUBLIC HEALTH WORKS
Non-Scheduled Items
Sr.
Item No. Description Unit Qty Rate Amount
No.
UPVC Multi Floor Trap (110x75mm) including strainer;
making required number of connections; breaking concrete
or masonry work & then making it good; etc. of approved
1 NSI make. Each 8.00
Providing, Fixing Dadex Class D or equivalent UPVC clean
out with cover making requisite number of holes in walls,
plinth or floor for pipe connection and making good the same
as necessary to the structure complete including, rubber
gasket and clamp.
2 NSI Each 4.00
3 NSI Providing and fitting "P" trap:ii) 10 cm (4") glazed. Each 37.00
Providing and fixing Wall Shower complete in all respects as
approved by the Engineer incharge. (Master, Sonex, or
Equivalent)
4 NSI Each 12.00
5 WATER SUPPLY PIPES AND FITTINGS
P/F Polypropylene Randam copolymer (PPRC) PN-20 pipe
with fusion / threaded joints including the cost of all specials/
accessories i.e elbow, bend, sockets etc. (Popular /Beta or
equivalent) complete in all respect.

i 1 1/2" (50 mm) dia. Rft 260.00

ii 1" (32 mm) dia. Rft 470.00

iii 2" (63 mm) dia. Rft 220.00

iv 3/4" (25 mm) dia. Rft 850.00

6 SOIL, WASTE, VENTILATING PIPES & FITTINGS
Providing , fixing and testing UPVC Nikasi type "B" with
solution of same quality make including the cost of all
specials/ accessories i.e elbow, bend, sockets etc.
(Popular/Beta or equivalent) complete in all respect.

i 100 mm (4") dia. Rft 660.00

ii 80 mm (3") dia. Rft 550.00

GAS GESYER
7 NSI Providing and Fixing Sui Gas Geyser 60 gallon capacity
comprising of internal tank of G.I sheet 14-SWG and
External M.S sheet 22-SWG covering with proper foot rests
dully enamel painted, 4" thick heigh density glass wool
insulation with proper warranty with thermostat temperature
gauge including fixing and making connection at site etc.
complete in all respects as approved by the Engineer
Incharge. (Ambassador/Firex/Exquire) No 2.00
Sr.
Item No. Description Unit Qty Rate Amount
No.
8 NSI Providing and Fixing Electric Geyser 20 gallon capacity
comprising of internal tank of G.I sheet 14-SWG and
External M.S sheet 22-SWG covering with proper foot rests
dully enamel painted, 4" thick heigh density glass wool
insulation with proper warranty with thermostat temperature
gauge including fixing and making connection at site etc.
complete in all respects as approved by the Engineer
Incharge. (Ambassador/Firex/Exquire) No 2.00
9 NSI Providing and fixing Gate valve 1 bars, RUV(itly) or
equivalent complete in all respects as approved by the
Engineer incharge.
Each 2.00
10 NSI Providing and fixing Gate valve 2 bars, RUV(itly) or
equivalent complete in all respects as approved by the
Engineer incharge. Each 2.00
Providing and fixing of 5.5 HP Centrifugal motor pump
having 50mm suction and 100ft head from approved
11 NSI
manufacturer complete in all respect as per approval of
Engineer Incharge. Each 2.00
NSI Supply and fixig, Pressure Booster Pump 0.5 Hp Shahzad
12 company or Equivalent complete in all respects as approved
by the Engineer Incharge. Each 2
Supplying and installing PVC blind pipe 'B' Class of
13 NSI approved design quality and make i/c necessary sockets etc.
complete.

a 1¼" i/d (30 mm) 1 x 70

Rft 150.00
b 1½" i/d (40 mm) 1 x 40
Rft 150.00
c 2" i/d (50 mm) 1 x 50
Rft 150.00
Total of Non SOR ITEMS
 CONSTRUCTION OF GIRLS HOSTEL FOR THE LIAQUAT UNIVERSITY OF MEDICIAL & HEALTH SCIENCE
JAMSHORO,SINDH

(COVERED AREA = 31019 Sft)

BILL OF QUANTITIES

ELECTRICAL WORKS
Rates Based on Composite Schedule of Rate (GENERAL-2012) Sindh

Sr. No. Item No. Description Unit Qty Rate Amount

1 DISTRIBUTION BOARDS

(General Description) Supply at site, fabrication, installation, testing

and commissioning of Distribution Board (DB) , made of sheet steel 16
SWG, degreased and derusted, with 2 coats of antirust paint, 2 coats
of powder coated paint of approved colour, protection classification IP-
44, totally enclosed indoor floor mounting cubicle type in free standing
design, with hinged door, handle including cost of all auxiliaries,
internal wiring, designation lables on MCCBS, grounding bar suitable
`
for system Voltage 440 V, 50 Hz, 3 Phase and neutral bus bars of
99.9% electrolytic copper, including cost of cable terminal blocks
wiring from breakers, brass cable glands, all accessories complete in
all respects mention in BOQ or not required for performing completely.
All incoming and outgoing breakers shall be accessible only by
opening the front door having further M.S. sheet cover gaskets shall
also be provided where necessary. Panel should be compeltely made
in certified factory. ie PEL, Green T & D, Mazcorp engiring or
equivalent as per instructions by engineer inchargee.e
(General Description) All MCCBs shall be suitable to operate without
any derating at 40°C ambient temperature and shall be of one make
only. The sides of MDB shall also have louvers at bottom and top on
sides of panel for hot air exhaust, wire mesh etc. The back of the
panel shall be lockable door instead of bolted and shall conform to
single line diagram. item should be of ABB, Schneider or equivalent as
per instructions by engineer incharge
i) MAIN DISTRIBUTION BOARD
INCOMMING
ELECT SH- Providing and fixing circuit breaker 125,150,200 & 225 amps TP(XS-
a
X(208) 225NS) on prepared board as required. Per No. 1 25541 25,541
ELECT SH- Providing and fixing circuit breaker 15,20,30,40,50, 75 & 100 amps
b
X(207) TP(XS-100NS) on prepared board as required. Per No. 1 9261 9,261
ELECT SH- Providing and fixing of current transformer of ration 60/5 amps (round)
c
XV(269) RLC-30 as required or as per instructed as EI. Per No. 3 1191 3,573
ELECT SH- Providing and fixing voltmeter size 96/96mm 500 volt as required and
d
XVI(285) as instruction of EI. Per No. 3 999 2,997
ELECT SH- Providing and fixing circuit breaker 6,10,15,20,30,40,50 & 63 amps
e
X(203) SP(TB-5S) on prepared board as required. Per No. 3 916 2,748
OUTGOING
ELECT SH- Providing and fixing circuit breaker 6,10,15,20,30,40,50 & 63 amps
f
X(203) SP(TB-5S) on prepared board as required. Per No. 3 916 2,748
ELECT SH- Providing and fixing circuit breaker 15,20,30,40,50, 75 & 100 amps
g
X(207) TP(XS-100NS) on prepared board as required. Per No. 11 9261 101,871
ELECT SH- Providing and fixing circuit breaker 125,150,200 & 225 amps TP(XS-
h
X(208) 225NS) on prepared board as required. Per No. 1 25541 25,541
ii) DISTRIBUTION BOARD DB- LIGHTING
INCOMMING
ELECT SH- Providing and fixing circuit breaker 15,20,30,40,50, 75 & 100 amps
a
X(207) TP(XS-100NS) on prepared board as required. Per No. 5 9261 46,305
ELECT SH- Providing and fixing of current transformer of ration 60/5 amps (round)
b
XV(269) RLC-30 as required or as per instructed as EI. Per No. 15 1191 17,865
ELECT SH- Providing and fixing voltmeter size 96/96mm 500 volt as required and
c
XVI(285) as instruction of EI. Per No. 15 999 14,985
ELECT SH- Providing and fixing circuit breaker 6,10,15,20,30,40,50 & 63 amps
d
X(203) SP(TB-5S) on prepared board as required. Per No. 15 916 13,740
OUTGOING
Sr. No. Item No. Description Unit Qty Rate Amount

ELECT SH- Providing and fixing circuit breaker 6,10,15,20,30,40,50 & 63 amps
e
X(203) SP(TB-5S) on prepared board as required. Per No. 80 916 73,280
iii) DISTRIBUTION BOARD DB- POWER
INCOMMING
ELECT SH- Providing and fixing circuit breaker 15,20,30,40,50, 75 & 100 amps
a
X(207) TP(XS-100NS) on prepared board as required. Per No. 4 9261 37,044
ELECT SH- Providing and fixing of current transformer of ration 60/5 amps (round)
b
XV(269) RLC-30 as required or as per instructed as EI. Per No. 12 1191 14,292
ELECT SH- Providing and fixing voltmeter size 96/96mm 500 volt as required and
c
XVI(285) as instruction of EI. Per No. 12 999 11,988
ELECT SH- Providing and fixing circuit breaker 6,10,15,20,30,40,50 & 63 amps
d
X(203) SP(TB-5S) on prepared board as required. Per No. 12 916 10,992
OUTGOING
ELECT SH- Providing and fixing circuit breaker 6,10,15,20,30,40,50 & 63 amps
e
X(203) SP(TB-5S) on prepared board as required. Per No. 80 916 73,280
iv) DISTRIBUTION BOARD DB- POWER 1
INCOMMING
ELECT SH- Providing and fixing circuit breaker 125,150,200 & 225 amps TP(XS-
a
X(208) 225NS) on prepared board as required. Per No. 1 25541 25,541
ELECT SH- Providing and fixing of current transformer of ration 60/5 amps (round)
b
XV(269) RLC-30 as required or as per instructed as EI. Per No. 3 1191 3,573
ELECT SH- Providing and fixing voltmeter size 96/96mm 500 volt as required and
c
XVI(285) as instruction of EI. Per No. 3 999 2,997
ELECT SH- Providing and fixing circuit breaker 6,10,15,20,30,40,50 & 63 amps
d
X(203) SP(TB-5S) on prepared board as required. Per No. 3 916 2,748
OUTGOING
ELECT SH- Providing and fixing circuit breaker 6,10,15,20,30,40,50 & 63 amps
e
X(203) SP(TB-5S) on prepared board as required. Per No. 28 916 25,648
ELECT SH- Providing and fixing circuit breaker 15,20,30,40,50, 75 & 100 amps
f
X(207) TP(XS-100NS) on prepared board as required. Per No. 2 9261 18,522
2 WIRING IN CONCEALED CONDUITS
i) Distribution board to Switch
(General Description) Wiring of light circuit from Distribution Board to
switch,with Three nos. single core 2.5 Sqmm PVC insulated 450/750
volts grade stranded copper conductor cables in concealed PVC
conduits (conduits partly shared) including PVC conduit, and conduit
accessories etc. Cable should be of Newage, Fast cable, Universal
cables or equivalent and conduit should be of Dadex, Turkplast,
Easyfit or equivalent as per instructions by engineer incharge
Providing and laying (main or Sub Main Pvc insulated with 3-7.29
a ELECT SH-(24) copper conductor in 3/4" dia PVC conduit recessed in the wall or
column as required. Rmtr 1290 294.00 379,260
ii) Switch to light point
(General Description) Wiring from switch to light or fan point with 3
nos. single core 1.5 Sqmm PVC insulated 450/750 Volts grade
stranded copper conductor cables in concealed PVC conduit including
PVC conduit, Conduit accessories,etc.(conduit partly shared).

a ELECT SH-(124) Wiring of Light and fan point with 3.29 Pvc insulated wire in 20mm
(3/4") dia PVC conduit recessed in the wall or column as required. Per/Point 671 1,130.00 758,230
Point to point wiring
Providing and laying (main or Sub Main Pvc insulated with 3-3.29
b ELECT SH-(22) copper conductor in 3/4" dia PVC conduit recessed in the wall or
column as required. Rmtr 1362 220.00 299,640
iii) Switch to Switch
(General Description) Wiring from switch to switch with 3 nos. single
core 2.5 Sqmm PVC insulated 450/750 Volts grade stranded copper
conductor cables in concealed PVC conduit including PVC conduit,
Conduit accessories,etc.(conduit partly shared).
Providing and laying (main or Sub Main Pvc insulated with 3-7.29
a ELECT SH-(24) copper conductor in 3/4" dia PVC conduit recessed in the wall or
column as required. Rmtr 1734 294.00 509,796
iv) Distribution board to General Purpose ( 5A/13A) socket
Sr. No. Item No. Description Unit Qty Rate Amount

(General Description) Wiring of circuit from Distribution Board to

5A/13A ,230Volts with 3 nos. single core 2.5 Sqmm PVC insulated
450/750 Volts graded , 2&3 pin switched socket, stranded copper
conductor cables in concealed PVC conduit, including conduit
accessories, etc(conduit partly shared)
Providing and laying (main or Sub Main Pvc insulated with 3-7.29
a ELECT SH-(24) copper conductor in 3/4" dia PVC conduit recessed in the wall or
column as required. Rmtr 2490 294.00 732,060
v) Socket to Socket
(General Description) Wiring from 5 Amps, 2&3 pin socket to socket
with 3 nos. single core 2.5 Sqmm PVC insulated 450/750 Volts grade
solid or stanerd copper conductor cables in concealed PVC conduit
including PVC conduit,Conduit accessories, etc complete. (conduit
partly shared)
Providing and laying (main or Sub Main Pvc insulated with 3-7.29
a ELECT SH-(24) copper conductor in 3/4" dia PVC conduit recessed in the wall or
column as required. Rmtr 1962 294.00 576,828
vi) Distribution board to 20Amps socket
(General Description) Wiring of circuit from distribution board to
20A, 230Volts, DP switch with 3 or 5 nos. single core 6 Sqmm PVC
insulated 450/750 Volts grade stranded copper conductor cables in
concealed PVC conduit including PVC conduit, Conduit accessories,
etc (conduit partly shared for A/Cs)
Providing and laying (main or Sub Main Pvc insulated with 3-7.44
a ELECT SH-I(26) copper conductor in 1" dia PVC conduit recessed in the wall or column
as required. Rmtr 90 468.00 42,120
Providing and laying (main or Sub Main Pvc insulated with 4-7.44
b ELECT SH-I(40) copper conductor in 1-1/2" dia PVC conduit recessed in the wall or
column as required. Rmtr 60 613.00 36,780
vii) Wiring for flood lights
Providing and laying (main or Sub Main Pvc) insulated with 3-7.36
a ELECT SH-I(25) copper conductor in 3/4" dia PVC conduit recessed in the wall or
column as required. Rmtr 260 338.00 87,880
3 LT Cables
Providing and Laying (MAIN or SUB MAIN) PVC insulated & PVC
i) ELECT SH-(113) sheeted with 4 core Armoured copper conductor 600/1000 volts size
16 mm2 Per Meter 185 1,679.00 310,615
Providing and Laying (MAIN or SUB MAIN) PVC insulated & PVC
ii) ELECT SH-(114) sheeted with 4 core Armoured copper conductor 600/1000 volts size
25 mm2 Per Meter 135 2,435.00 328,725
Providing and Laying (MAIN or SUB MAIN) PVC insulated & PVC
iii) ELECT SH-(115) sheeted with 4 core Armoured copper conductor 600/1000 volts size
35 mm2 Per Meter 40 3,008.00 120,320
Providing and Laying (MAIN or SUB MAIN) PVC insulated & PVC
iv) ELECT SH-(116) sheeted with 4 core Armoured copper conductor 600/1000 volts size
50 mm2 Per Meter 55 3,910.00 215,050
Providing and Laying (MAIN or SUB MAIN) PVC insulated & PVC
iv) ELECT SH-(119) sheeted with 4 core Armoured copper conductor 600/1000 volts size
120 mm2 Per Meter 40 9,606.00 384,240
4 MISCELLANEOUS FITTINGS
i) ELECT SH(234) Providing and fixing brass Ceiling fan 48'' (good quality)
Per No. 104 3,020.00 314,080
ii) ELECT SH(235) Providing and fixing brass Ceiling fan 56'' (good quality) Per No. 35 3,185.00 111,475
Total of SOR Items 5,774,179
CONSTRUCTION OF GIRLS HOSTEL FOR THE LIAQUAT UNIVERSITY OF MEDICIAL & HEALTH SCIENCE
JAMSHORO,SINDH

(COVERED AREA = 31019 Sft)

BILL OF QUANTITIES

ELECTRICAL WORKS
Non-Scheduled Items

Sr. No. Item No. Description Unit Qty Rate Amount

1 DISTRIBUTION BOARDS

(General Description)Supply at site, fabrication, installation,

testing and commissioning of Distribution Board (DB) , made
of sheet steel 16 SWG, degreased and derusted, with 2 coats
of antirust paint, 2 coats of powder coated paint of approved
colour, protection classification IP-44, totally enclosed indoor
floor mounting cubicle type in free standing design, with
hinged door, handle including cost of all auxiliaries, internal
wiring, designation lables on MCCBS, grounding bar suitable
for system Voltage 440V, 50 Hz, 3 Phase and neutral bus
bars of 99.9% electrolytic copper, including cost of cable
terminal blocks wiring from breakers, brass cable glands, all
accessories complete in all respects mention in BOQ or not
required for performing completely. All incoming and outgoing
breakers shall be accessible only by opening the front door
having further M.S. sheet cover gaskets shall also be
provided where necessary. Panel should be compeltely
made in certified factory. ie PEL, Green T & D, Mazcorp
engineering or equivalent as per instructions by engineer
incharge.
(General Description) All MCCBs shall be suitable to
operate without any derating at 40°C ambient temperature
and shall be of one make only. The sides of MDB shall also
have louvers at bottom and top on sides of panel for hot air
exhaust, wire mesh etc. The back of the panel shall be
lockable door instead of bolted and shall conform to single
line diagram. item should be of ABB, Schneider or equivalent
as per instructions by engineer incharge.
i) MAIN DISTRIBUTION BOARD
INCOMING
Providing and fixing of Metal Clad, free standing, front
access, totally enclosed, frame febrecated from 14/16 SWG,
MS sheet with surface treatment Powder Coated Paint RAL
7035, Texture White, Suitable for system voltage 400/230,
50HZ, 3 Phase Copper bus bar, Neutral bus bar, Earting bus
NSI bar and internally wired., Mechanical interlocking for MCCBs, Job 1
03 No Phase Indication Lights, 220 VAC (R-Y-B) 01 No
Digital Ampere Meter,01 No Ampere Selector Switch,03 No
CTs 200/5A Wall Mounted DB Panel In door Type (Suitable
Size) complete in all respect as approved or directed by
engineer incharge.
ii) DISTRIBUTION BOARD DB- LIGHTING
INCOMING
 Providing and fixing of Metal Clad, free standing, front
access, totally enclosed, frame febrecated from 14/16 SWG,
MS sheet with surface treatment Powder Coated Paint RAL
7035, Texture White, Suitable for system voltage 400/230,
50HZ, 3 Phase Copper bus bar, Neutral bus bar, Earting bus
NSI bar and internally wired., Mechanical interlocking for MCCBs, Job 1
03 No Phase Indication Lights, 220 VAC (R-Y-B) 01 No
Digital Ampere Meter,01 No Ampere Selector Switch,03 No
CTs 200/5A Wall Mounted DB Panel In door Type (Suitable
Size) complete in all respect as approved or directed by
engineer incharge.
iii) DISTRIBUTION BOARD DB- POWER
INCOMING
Providing and fixing of Metal Clad, free standing, front
access, totally enclosed, frame febrecated from 14/16 SWG,
MS sheet with surface treatment Powder Coated Paint RAL
7035, Texture White, Suitable for system voltage 400/230,
50HZ, 3 Phase Copper bus bar, Neutral bus bar, Earting bus
NSI bar and internally wired., Mechanical interlocking for MCCBs, Job 1
03 No Phase Indication Lights, 220 VAC (R-Y-B) 01 No
Digital Ampere Meter,01 No Ampere Selector Switch,03 No
CTs 200/5A Wall Mounted DB Panel In door Type (Suitable
Size) complete in all respect as approved or directed by
engineer incharge.
iv) DISTRIBUTION BOARD DB- POWER 1
INCOMING
Providing and fixing of Metal Clad, free standing, front
access, totally enclosed, frame febrecated from 14/16 SWG,
MS sheet with surface treatment Powder Coated Paint RAL
7035, Texture White, Suitable for system voltage 400/230,
50HZ, 3 Phase Copper bus bar, Neutral bus bar, Earting bus
NSI bar and internally wired., Mechanical interlocking for MCCBs, Job 1
03 No Phase Indication Lights, 220 VAC (R-Y-B) 01 No
Digital Ampere Meter,01 No Ampere Selector Switch,03 No
CTs 200/5A Wall Mounted DB Panel In door Type (Suitable
Size) complete in all respect as approved or directed by
engineer incharge.

2 LIGHT FIXTURES
(General Description) Supply, installation, testing and
commissioning of following light fittings, ceiling,
recessed,wall mounted as per specified fixture. Complete
with internal wiring, Grounding terminal , driver complete in all
respects. Lights should be of Phillips, ledvance, Sky LED or
equivalent. 179
i) NSI 24 Watt (White) LED Light Fixture surface/recessed
mounted, IP-22 rated No. 405
ii) NSI 18 Watt (White) LED Light Fixture surface/recessed
mounted, IP-22 rated No. 145
iii) NSI 12 Watt LED Light Fixture surface/recessed mounted, IP-22
rated No. 34
iv) NSI 09 Watt Fancy light No. 150
v) NSI 20 Watt Flood lights No. 9
3 MISCELLANEOUS FITTINGS
(General Description) Supply, installation, testing &
commissioning of Ceiling/ Exhaust fan. The ceiling/exhaust
fan shall comprise circular fan metallic/ plastic body, metallic
fan blades, down rod (if necessary) of suitable dia & length,
AC capacitor, internal wiring, terminals all installation &
operational accessories as per tender specifications, as per
site requirements and as per instructions by the Engineer.
make GFC, Pak Fan, Royal Fan or approved equivalent.
16
 i) NSI 10 '' outer dia exhaust fan with plastic body,fan blades and
louvers No. 16
4 WIRING ACCESSORIES
(General Description) Supply at site, installation, testing and
commissioning of the following wiring accessories, complete
in all respects. Made of TJ, Legrand or approved equivalent.
i) NSI 10 Amps, 250Volts one way, One gang light control switches
including appropriate size concealed Plastic back box. No. 163
ii) NSI 10 Amps, 250Volts one way, Two gang light control switches
including appropriate size concealed Plastic back box. No. 67
iii) NSI 10 Amps, 250Volts one way, Three gang light control
switches including appropriate size concealed Plastic back
box. No. 17
iv) NSI 10 Amps, 250Volts one way, Four gang light control switches

including appropriate size concealed Plastic back box. No. 10

v) NSI 10 Amps, 250Volts one way, Five gang light control switches

including appropriate size concealed Plastic back box. No. 8

vi) NSI 10 Amps, 250Volts one way, Six gang light control switches

including appropriate size concealed Plastic back box. No. 63

vii) NSI 10 Amps, 250Volts two way, one gang light control switches

including appropriate size concealed Plastic back box. No. 4

viii) NSI 13 Amps, 250Volts, 3 pin flat switch socket single outlet
including appropriate size Plastic back box. No. 410
ix) NSI 15Amp 3Pin Round Switch Socket Outlet including
appropriate size Plastic back box. No. 1
x) NSI 20A DP Switch with Neon & Earth including appropriate size
Plastic back box. No. 3
xi) NSI 45A TP breaker with appropriate size Plastic cover box. No. 2
xii) NSI 1-Gang Cat-6 RJ45 Data Outlet No. 17
xiii) NSI Fan Dimmer 250 watt including appropriate size Plastic back
box. with all associated accessories. No. 139
xiv) NSI Appropiate size of plastic body fan box and ceiling fan rod 24"
in length Nos 139
xv) NSI MS BAR for hanging Ceiling fan Nos 139
5 GROUNDING SYSTEM
i) GROUNDING cable
Supply at site, installation, testing and commissioning of PVC
insulated non armoured copper conductor cable 450/ 750 Volt
grade (or otherwise mentioned in cable description ) in
prelaid conduits / trenches to be installed as per routes
shown on drawings including cost of all necessary materials,
connections, identification tags, cables lugs properly crimped
at both ends for the following sizes complete in all respects.
Actual length of cables to be installed shall be practically
measured at site by the Contractor, duly authenticated by the
Engineer before placing the order with the manufacturer,
however, approximate length of cables are shown herewith.
Payments shall be made as per actual length installed. Cable
should be of FAST, Newage or universal cables and conduit
should be of Solo,popular,easyfit or equivalent as approved
by engineer incharge

NSI Supply and erection of single core PVC insulated, PVC

sheathed copper conductor, 660/1100 volts grade cable, in
prelaid G.I. pipe/M.S. conduits/PVC pipe/G.I. wire/trenches,
etc (rate for cable only):-
a 6 mm sq (7/0.044") rmtr 245
 NSI Supply and erection of single core PVC insulated, PVC
sheathed copper conductor, 660/1100 volts grade cable, in
prelaid G.I. pipe/M.S. conduits/PVC pipe/G.I. wire/trenches,
etc (rate for cable only):-
b 10 mm sq (7/0.052") rmtr 135
NSI Supply and erection of single core PVC insulated, PVC
sheathed copper conductor, 660/1100 volts grade cable, in
prelaid G.I. pipe/M.S. conduits/PVC pipe/G.I. wire/trenches,
etc (rate for cable only):-
c 16 mm sq (7/0.064") rmtr 135
6 Earthing
NSI Supply, installation, testing and commissioning of earthing
system for protecting Earthing of Rod 19 mm 10 ft long with
bare solid Earth conductor 1 x 35sq.mm upto earth
connecting point, inspection chamber, marconite concrete,
drilling etc, to achieve less than 3 ohms specified Earthing
results. complete in all respect as per drawing and
specification or as per directed by Engineer. Each 1
7 Fire Alarm System
(General Description) Supply, installation, testing and
commissioning of following items as per drawings,
specifications, & instructions of the Engineer, complete in all
respect, all item should be of Gent by honeywell, ETON
uk,TNA UK or approved equivalent as per instructions by the
Engineer as required.
i) Manual Call Point
NSI Supply, install testing and commsiong of Addressable Manual
Call Point Flush Mount Resetable Call Point, supplied with
resetable key. Optional Accessories: TX7140-MB Surface
Mount Back Box, TX7140-PFC Protective Flip Cover.
Make:TNA UK or equivalent complete in all respect as
approved or directed by engineer incharge.
Each 6
ii) Smoke Detector
NSI
Supply, install testing and commsiong of Photoelectric type
Fastest resoponse to slow burning or smoldering fires,
reliable early detection Smart drift compensation, auto
compensate for dust or other environmental changes that
affect the performance Stability & prevent fault alarm 360-
degree visual indicator Support remote indicator
output.Accessories: Base: TX7980 Standard Addressable
Base, TX7322 Addressable Sounder Base, TX7232 Base
Mount Short Circuit Isolator , TX7302 Addressable Flashing
Beacon Base Standard base for addressable detectors
Make:TNA UK or equivalent complete in all respect as
approved or directed by engineer incharge.
Each 98
iii) Sounder
NSI Supply, install testing and commsiong of Addressable
Sounder 17 sound tones selection Loop powered Low and
normal consumption mode Up to 102dB at 1 meter
Make:TNA UK or equivalent complete in all respect as
approved or directed by engineer incharge. Each 6
iv) FACP
 NSI
Supply, install testing and commsiong of Addressable Fire
Alarm Control Panel 2 loop. Fire alarm control panel, indicate
fire and fault status LCD screen provide real time system &
devices information, easy operation and maintainance PC
and keypad programming & control, user firendly Built-in
Panel Printer, NC7004 Communication Card Outer glass door
Wall-mounted Cabinet Size (W X H X D mm): 530 mm x
490 mm x 135 mm Optional Accessories: TX7814 Dongle for
TX7, Batteries Make:TNA UK or equivalent complete in all
respect as approved or directed by engineer incharge. Each 1
v) Cable
NSI Supply, install testing and commsiong of 2 x 2.5 mmsq
shielded drain wire, 30 minutes fire resistance,red, LPCB
approved, BS 7629-1/2008, BS 5839-1 standard.(Newage,
Pakistan Cable, Fast or approved equivalent). as per
instructions by engineer incharge. Rmtr 560
vi) Conduit
NSI Supply and erection of PVC pipe for wiring recessed in
walls,including inspection boxes, pull boxes, hooks, cutting
jharriesand repairing surface, etc., complete with all
specials.25 mm i/d R.Mtr 560
vii) Programming, Testing and Commissioning
NSI Programming, Testing and Commissioning of Complete
system by authorized certified company complete in all
respects as per instructions of the Engineer. Lum sum 1
viii) Fire Extinguishers
NSI Supply & installation of Dry Chemical Powder (M.S-Steel):
Providing of New Fire Extinguisher Dry Chemical Powder
(DCP) with one year warranty and filled with Nitrogen
pressure along with Wall hook and discharge pipe. Complete
in All respects.as approved or directed by engineer incharge. Nos. 4
8 Data System
i) Data Cable
NSI
Supply, installation, Testing and commissioning of CAT 6
UTP CABLE IN prelaid PVC PIPE Ø 1"; MEASUREMENT IN
METERS complete in all respects. Made of Hikvision,D-Link
or equivalent approved by engineer incharge R.Mtr 855
ii) Conduit
NSI Supply and erection of PVC pipe for wiring recessed in
walls,including inspection boxes, pull boxes, hooks, cutting
jharriesand repairing surface, etc., complete with all
specials.25 mm i/d R.Mtr 855
iii) Data Cabinet
NSI Supply , installation of wall mounted CCTV Cabinet
comprising of Powder Coated M.S frame, front glass & two
side openings,with all necessary accessories/ materials,
complete in all respects. Made of Bosch/ HP / Dell , Pollo
Australia, or equivalent or as approved and directed by
Engineer Incharge(i) 12U Each 1
iv) Cable Manager
NSI Supply and installation of Cable Metal Organizer, 19" Rack
mounted with high graded epoxy powder coating and
slideable top- UL Listed. Made of Schneider/i-Connect UK/3M
Corning: Pollo Australia or equivalent as approved and
directed by the Engineer Incharge Each 1
v) Patch Panel
 NSI Supply and installation of CAT-6 (24 Port Patch Panel with
Toolless Support 10-Gigabit). UTP Patch Panel with specified
toolless support & Rear Cable Management, UL listed,
Loaded with UTP of specified Keystone Jack Toolless
Support , Made of Schneider / Norden /3M Corning/D-Link,
Pollo Australia or equivalent or as Approved and Directed by
Engineer Incharge. Each 1
vi) PDU
NSI Supply & Installation of PDU as approved or directed by
engineer incharge. Each 1
vii) 24 Port PoE Data Switch
NSI
Supply, Installation and Connection of Hikvision 24 Port
Gigabit Unmanaged POE Switch, 24 × Gigabit PoE ports,
2 × Gigabit SFP fiber optical ports, IEEE 802.3at/af standard,
6 KV surge protection for PoE ports, PoE power
management, Gigabit network access, MAC Address Table :
8 K, Switching Capacity : 52 Gbps, Packet Forwarding Rate :
38.688 Mpps, Internal Cache : 4.1 Mbits, Wire-speed
forwarding, Store-and-forward switching, Solid high-strength
metal shell made of Hikvision Model no DS-3E0526P-E/M ,
Huawei, Cisco USA or equivalent as approved or directed by
engineer incharge. Each 1
viii) Wifi Router
NSI

Supply, Installation and commissioning of TP-Link AC750

Dual-Band Wi-Fi RouterHigh-Speed Wi-Fi—AC750 dual-band
is ideal for HD video streaming, high-speed downloading. Far-
Reaching Coverage—4× antennas deliver far-reaching Wi-Fi
and reliable connections. Multi-Mode 3 in 1—Supports
Router, Access Point, and Range Extender to add flexibilities.
Parental Controls—Manages when and how connected
devices can access the internet. Guest Network—Provides
separate access for guests while securing the host network.
Smooth HD Streaming—Supports IGMP Proxy/Snooping,
Bridge and Tag VLAN to optimize IPTV streaming. IPv6
Supported—Compatible with the IPv6 (the latest Internet
Protocol version 6). Compact and Mountable—Designed to
conserve space and complement any décor. as per
specification as approved or directed by engineer incharge. Each 8
9 CIVIL WORKS
i) Trench
NSI
Labour for excavation and refilling of trench 12" wide, 36"
deep 4" sand, bricks and warning tape. Compaction below
and above preinstalled PVC pipes if any, ramming watering
all necessary material, labour etc, complete in all respect.
Actual length of the trench shall be as per site condition and
paid accordingly however approximate length of trench is
given. as approved and directed by engineer incharge. R.Mtr 115
ii) Manhole For LT Cable Pulling ( If Required)
NSI Construction of manholes to facilitate pulling of cables in
trench or conduit as shown on drawing, manholes shall be of
the size 24" x 24" x 30" deep with 9" thick wall with cement
mortar, internal plaster 1:4, 100mm thick RCC cover for
manhole, including cost of all accessories / materials,
complete in all respects. (Tentative number of manholes have
been provided, however payment shall be made as per actual
and as per quantity requirement) Nos. 9
10 Air Conditioning
 (General Description) Providing, shifting, fixing, testing,
commissioning, adjusting and balancing of standard ( Cool
only) DC inverter technology air condiotioning units, including
indoor evaporating and out door condensing unit, the indoor
units wall mounted of capacities as specified below,
complete with factory charged refrigerant, piping insulation
including condensate copper piping connection, between
indoor/outdoor units conduiting and any additional charge of
refrigerant accessories, and Drain piping upto nearest drain
water line included in these rates making the job complete in
all respect. AC should be of Haier,dawlance, gree or
equivalent, copper piping should be of muller, trox and
insulation of Durkflex or equivalent, Drain pipe should be 3/4"
dia pvc pipeof master, turkplast or equivalent as per
instructions by engineer incharge
(General Description) 1/4 and 1/2 copper piping shouls be
used till 1.5 ton AC and 5/8 and 3/8 piping should be used for
2 ton AC and 3/8 and 1/2 for 4 ton AC between indoor and
outdoor unit.
(General Description) The AC Unit should maintain approx
11 BTU per cubic feet plus addition of 3000BTU in the total
amount for persons and devices
i) Copper pipe
NSI Supply ,installation testing and commissioning of Copper
piping 1/2 insulation and control wire including making
a
jharies and repairing of surface with all neccessary item job
must be complete in all respect RFT 50
NSI Supply ,installation testing and commissioning of Copper
piping 3/8 with insulation and control wire including making
b
jharies and repairing of surface with all neccessary item job
must be complete in all respect RFT 100
NSI Supply ,installation testing and commissioning of Copper
piping 5/8 with insulation and control wire including making
jharies and repairing of surface with all neccessary item job
must be complete in all respect RFT 50
ii) Drain Pipe
NSI
Providing, laying, testing and commissioning of 1/2'' µ-PVC
(Un plasticized Polyvinyl Chloride) Schedule pipe of nominal
diameter, Dadex/Popular / Beta or approved equivalent
manufacturer, i/c the cost of solvent and specials complete
as approved and directed by the Engineer Incharge.
RMTR 40
iii) Control Cable
Supply and erection of copper conductor cables for
serviceconnection, in prelaid pipe/G.I. wire/trenches, etc.
(rate for cable only):-
b) PVC insulated, PVC sheathed 3 core flexible cable ,
300/500 volt cable:
iii) 7/0.74 mm (7/0.029") Rmtr 40
iv) Copper pipe insulation
Supply & installation closed cell type Aluminium foil faced
XLPE (Cross linked polyethelene) polyolefin pipe insulation
tube of density 25 Kg/m³ of specified thickness & thermal
conductivity 0.035 w/m °C and fire retardent of Class "o"
rating as specified for refrigerant copper piping as approved
by the Engineer Incharge.
a) 20 mm thick
a NSI 1/2'' dia RFT 50
b NSI 3/8'' dia RFT 100
c NSI 5/8'' dia RFT 50
11 Duct panel
Supply at site and installation of duct panel on wall where
necessary made of popular, dadex, turkplast or equivalent as
approved or directed by engineer incharge.
 a NSI 16 x 25 mm Rmtr 50
b NSI 25 x 25 mm Rmtr 50
12 CONDUITS, PIPES, DUCT , CABLE TRAYS, FIXING
CLAMPS AND FIXING ARRANGEMENTS
Supply, installation, testing and commisiioning of following
conduits laid under floor for telephone/ data cables , optical
fiber cables, Sub main power cables & earth cables including
all conduit accessories. The PVC conduits shall be laid
under floor including chiseling and cutting of floor for required
dimensions, laying of conduit, backfilling of remaining cavity
with CC as specified for floor in that area, making good,
complete in all respect. conduit made of solo, popular, easyfit
or equivalent as approved by engineer incharge.

NSI
Supply and erection of PVC pipe for wiring recessed in wall
including inspection boxes, pull boxes, bends, tees,
repairing surface, etc., complete with all specials:made of
easyfit, popular or equivalent as approved or directed by
engineer incharge.
i) 25 mmi/d R.Mtr 50

Supply and erection PVC pipe for recessed wiring (main and
sub-main) purpose, including bends, specials, etc. in floor,
ii) wall or trenches:
a NSI 50 mm i/d R.Mtr 320
b NSI 80 mm i/d R.Mtr 95
c NSI 100 mm i/d R.Mtr 40
Total of Non-SOR Items