10.

Caution Installation Manual

1. When the temperature is too high, HI will be displayed in the temperature erea to express the room

@everweJJ®
temperature over the display range. When the temperature is too low, LO will be displayed in the
temperature erea to express the room temperature blow the display range. TH-AC10
2. Two AA batteries can be used for one year. When the battery voltage symbol flashes, it means the Programmable Thermostat
batteries need to be changed. Please change the batteries sooner.
3. Within the 20 minutes after remove the batteries, time and week will keep running. Please change
the batteries in this period.
Table of Contents Page 2.2 Feature
4. There is preservative on the LCD when out of the factory, users can remove it or not.
• Programmable thermostat
5. If you need to remove the preservative, just pull it from the corner and no need to open the thermostat.
Preface 1 • 5+2 Programmable
6. Don't force to install. When it is hard to connect the pin, move the display panel slightly. After the pin Production Function Overview 1 • Easy to program
aimed at the port, press the thermostat hard. Diagram and Description 2~3 • Easy to install
7. It is precision electronic products. Don't knock or fall it. Wall locations 4
• 6.8 square inch display
8. Don't let the water, mud into the thermostat. Subbase Installation 5
• Battery power or 24V Hardwire
WIRING 6
Wiring Diagrams 7 • Operate on 1 stage Heat and 1 stage cool
Operation 8~10 • Heat Pump without Aux or Emergency Heat
11.SPECIFICATIONS Mount Thermostat & Battery Installation 11 • Separate heating and cooling swing(cycle
Caution 12 rate) adjustments
Specifications 12 • 5 minutes compressor delay protection
Specifications
(selectable on or off)
the display range of temperature ............. .44°F to 90°F ( 7°C to 32°C) • Gas, Electric or Oil
1.Preface
the control range of temperature ............. .44 °F to 90°F ( 7°C to 32°C) • Optional temperature display of Fahrenheit or
Load rating ................................................ 1 amp per terminal, 1.5 amp maximum all terminals combined Dear client, Celsius scale.
Display accuracy ......................................± 0.5°C Thanks for choosing TH-AC10 thermostat • Low Battery Indicator
Power source ............................................ 18 to 30 VAC, NEC Class II, 50/60 Hz for hardwire (common wire) series. It's our best wish to bring you convenience • Display temperature calibration
Battery power from 2 AA Alkaline batteries for your daily life. Before using, please read the
Operating ambient.. ................................. .41°F to +95°F(5°C to +35°C) User's Manual carefully. It will help you to use it
Operating humidity.................................... 90% non-condensing maximum correctly.
Dimensions of thermostat. ........................ 118mm * 88mm * 30mm

2.Production Function Overview

2.1 Application
Description
1 stage Heat and 1 stage Cool Yes
A A trained, experienced
technician must install this
product.

Gas or Oil Heat Yes Carefully read these instructions.

You could damage this product or
Electric Furnace Yes
cause a hazardous condition if
Heat Pump( NO Aux. or Emergency Heat) Yes you fail to follow these instructions.
Heat Only Systems Yes
Heat Only Systems - Floor or Wall Furnaces Yes
Cool Only Systems Yes
Millivolt Yes

■ ■ fW
3.Diagram and Description

11 12 13 1415
! ! !
Hold/Set key: Press the HOLD only once,the LCD display "hold",and the
thermostat keeps the current mode and setting temperature.in the cool/heat
,,,, r,... 6 mode, press it to keep the setting temperature, and the setting temperature
will not change in the setting process. In the cool/heat mode, press and hold
COOL - the key for 3 seconds to enter the setting interface. When power off, hold the
o. .
HEAT
OFF
key for 5 seconds to enter the parameter changing interface.
CoolHeat Setting ..... ............. 3
10············................ ..... ................................ . . . 1Cl Cl ~E1
I LJ LJ.ot cbol On ! *:.~•,. \
Sy~te?l
o. . 7 Clock/Week: Display the current system time and week.

,
FAN
.: ~~, .:
G!ill: Hea1._0n! ............. 4 Hold symbol: when the symbol displayed, the setting temperature will be

I r, r,OF.-,
.....

- Fan ~Off 8 kept and won't follow the setting program.

9 .............. .
Inside
. .. ................................. ..............................
0

0 LJ.o°C
On Auto
~ ..........
o. .
RUN

..... . ............ 5 9 Room temperature: display the current room temperature.

...u
2 . . . . . . . . . . . . . . .....
■ ;t;JE:I T~~te I Cl •Cl Cl Am ~~~f$
PRGM Setting
o. .
HOLD

SET
..... ............. 6
10
11
Setting temperature: display the setting temperature in the cool/heat mode.
Battery symbol: it means low power when the symbol displayed, so
please change the battery in time.
f LJ •LJ LJ Pm mmlml
1 ............... . . . v
WakeLeaveReturnSleep
Day
Mon Tue Wid Thu Fri Sat Sun
............................. .. . . . . . . . . . . . . . . . . 16
. ... Cool symbol: The cooling relay start to work when the symbol displayed.
12 The symbol flashing means the cooling relay is in the set-up delay process.

...,
<tJJeverwe/f -
v 13
Heat symbol: The heating relay start to work when the symbol displayed.
The symbol flashing means the cool relay is in the set-up delay process .
14 System cool: The symbol displayed means it is in the cooling mode.
8 7 17 15 System heat: The symbol displayed means it is in the heating mode.
16 Fan: display the current mode of the fan.
17 Program setting: it shows the system is in the setting process
Description
Item Description
Down key: in the cooling/heating mode, it is for lowering the setting
1 temperature. When setting the program and changing the system parameter,
it is for adjusting the parameter.

Up key: in the cooling/heating mode, it is for raising the setting temperature.

2 When setting the program and changing the system parameter, it is for
adjusting the parameter.

Mode key: First press for cool mode, and second is for heat mode. Press
3 again will turn off the thermostat.
4 Fan mode: in the cooling/heating mode, switch the fan between on and auto.
Run key: Press only once.the thermostat operates according to the time
5 programming.After setting the program and changing the system parameter,
press the run key to save and exit the setting interface.
4.Wall locations 5. Subbase Installation

The thermostat should be installed approximate 4 to 5 feet above the floor.

Select an area with average temperature and good air circulation. Caution: Caution:
A Electrical Hazard
Failure to disconnect the
power before beginning to
A Equipment damage
hazard
Do not operate the cooling
install this product can cause system if the outdoor
electrical shock or equipment temperature is below 50° F
damage. (10° C) to prevent possible
compressor damage.

NO YES

NO

Do not install thermostat at following places:

• Close to hot or cold air ducts
• With direct sunlight
• With an outside wall behind the thermostat Insert the awl into the slot and pry up For horizontal mount put one screw left
the front part of the panel to open it. and one screw right.
• The areas that do not require conditioning
• Where there are dead spots or drafts (in corners or behind doors)
• Where there might be concealed chimneys or pipes

Installation Tip

Pick an installation location that is easy for the user to access. The temperature of the location
should be representative of the building.
6. Wiring 7. Wiring Diagrams

A Power supply
A Factory-installed jumper. Remove only when installing on 2-transformer systems

A Caution: Electrical Hazard

Failure to disconnect the power

before beginning to install this
A Warning:

All components of the control

system and the thermostat
A
A
In heat pump mode, please check the reversing vlave to see whether it is in O or B position, and
enter the system to set reversing valve to the position you need.
The system is in the electronic mode in default setting. If the system is gas or oil supported, enter
product can cause electrical installation must conform to the setting interface to set it in the gas mode.
shock or equipment damage. Class II circuits per the NEC Code.
A Optional 24 VAC common connection when thermostat is used on battery power mode

Wiring Typical 1 H/1 C system: 1 transformer Typical 1H/1C system: 2 transformer

C
1.lf you are replacing a thermostat. Take Caution: REMOVE JUMPER C
notice of the terminal connections on the
cases, the wiring connections may not be
color coded. For example, the green wire
may not be connected to the G terminal.
A Do not over tighten terminal block
screws, as this can damage
terminal block, and keep the COMPRESSOR
RELAY
[nJ

COMPRESSOR
RA
L2
L1(HOT)

thermostat fitting on the sub-base RELAY

correctly or it will cause system
2.Loosen the terminal block screws. Insert operation issues.
HEAT RELAY
HEAT RELAY
wires then retighten terminal block screws.
FAN RELAY
Max Torque = 6in-lbs FAN RELAY
3.Place nonflammable insulation into wall L2
opening to prevent drafts. L1(HOT)

RA
Typical 1 H/1 C heat pump system A Typical heat-only system
Terminal Designation C
C
L2
L1(HOT)
C Common wire from secondary side RH Transformer power for heating
of cooling system transformer RA
O Heat pump changeover valve RC Transformer power for cooling
energizes in cooling G Fan relay HEAT RELAY
B Heat pump changeover valve energizes
in heating Y Compressor relay
COOL CHANGE
OVER VALVE
W Heat relay HEAT CHANGE
OVER VALVE
A 1.Please
DD set on the heat pump system first
2.Please set the valve as heating/cooling system.

Wiring Tips: Typical heat-only system with fan Typical cool-only system
C
C

RH & RC terminals C terminal

For single transformer systems, leave the jumper The C ( common wire ) terminal does not Re
wire in place between RH and RC. Remove jumper have to be connected when the RH COMPRESSOR
wire for two transformer systems. thermostat is powered by batteries. y RELAY

C
Wire specifications HEAT RELAY
FAN RELAY
Use shielded or nor-shielded 18 - 22 gauge thermostat wire.
FAN RELAY
a.Operation

8.1 Operation EXAMPLE:

Heating/Cooling Schedule Plan(Factory default program setting)
(1) COOL/HEAT/OFF: press the" COOL/HEAT/OFF" key once to turn on the system. The mode is Weekdays (5 day) Saturday and Sunday
cool and"$" is displayed. Meanwhile the room temperature, setting temperature, clock will be also Mode Period Start Time Temperature Start Time Temperature
displayed. Change to the heat mode by the second pressing and"~~;" is displayed. Press again to
Wake 6:00AM 21 °C 6:00AM 21 °C
turn off the system and "off" is displayed.
Leave 8:00AM 17°C 8:00AM 17°C
Heat
(2) Setting temperature: when power on, press" 0, "or" Q "to set the temperature. Press Return 6:00 PM 21 °C 6:00 PM 21 °C
"Q "to lower the setting temperature, and press" 0, "to raise the setting temperature. Sleep 10:00 PM 17°C 10:00 PM 17°C
Wake 6:00AM 24°C 6:00AM 24°C
(3) Fan mode: When power on, press it to choose the fan on, and press again to change the Leave 8:00AM 28°C 8:00AM 28°C
fan to auto mode. Cool
Return 6:00 PM 24°C 6:00 PM 24°C
Sleep 10:00 PM 26°C 10:00 PM 26°C
(4) Run key: When power on, press the key to run the program what has been set. Meanwhile
"Run On" is displayed. In the programming mode or changing the system parameter, press
"RUN" to exit and save the changed parameter.

(5) Hold key: When power on, press the "Hold" key to keep the setting temperature. It won't 8.3 System parameter setting
run the program and display "Hold". For example: now the setting temperature is 60°F ,after
When power off, hold " SET " key for 5 seconds to enter the parameter changing interface.
pressing the "HOLD" the system will lock the setting temperature to be 60°F.
Room temperature area displays each symbol of the parameter, and system clock area displays
each parameter of the parameter values. Repeat to press " SET " key to cycling display the each
parameter. Press "0," or" Q" to adjust each parameter. After finished changing, press " RUN "key
8.2 Programming setting to exit the setting interface and save the set parameter.(if there's no any operation within 30 seconds
when setting, the system will exit the setting interface and abandon the changed parameter.)
When power on(in cool/heat mode),hold "SET" for 3 seconds to enter the programming
mode: Display(Factory Press6or Default
Step Press Buttons Description
Defaults) Qto select parameters
(1) First is to set the system clock. When the clock area is flashing, press" 0," or" Q" to 01 SETS seconds cc FA or SL FA Select fast cooling or slow cooling
change the clock. And if you hold "0," or "Q" , the adjustment will be faster. 02 SET HC FA or SL FA Select fast heating or slow heating
03 SET FC Fore C Select °F or °C Readout
(2) Press" SET" again to set the week. When the week flashing, press" 0," or" Q" to change
Compressor Lockout delay time
the week. 04 SET CP 0 or 5 0
0 = none ; 5 = Minutes
(3) Press" SET" again to set the Wake time from Monday to Friday. When the clock area is 05 SET CA -5°to +5° 0 room temperature error correction
flashing, press" 0," or" Q" to adjust the time. conventional heat pump selection
06 SET HP 1 or 0 0 0:conventionalmode
1: heat pump mode
(4) Press" SET" again to set the Wake temperature from Monday to Friday. When the clock area is
Select cool/heat change over valve
flashing, press" 0," or" Q "to adjust the temperature. 07 SET Ob 0 orb 0 "b" = heat change over valve
"O" =cool change over valve
(5) Repeat pressing the" SET", then you can set the time and temperature of Leave, Return, Sleep, Intelligent Recovery Option
08 SET IC 1 or 0 0
from Monday to Friday and Saturday, Sunday by turn. "1" = Active "0" =Deactivated
09 SET 6E E or 6 E "E"=Electric "6"=Gas
(6) After finished the setting, press the" RUN "to cancel the setting interface and save the parameter. RETURNS TO
(if there's no any operation within 30 seconds when setting, the system will exit the setting interface 10 RUN NORMAL
and abandon the changed parameter.) OPERATION
 9. Mount Thermostat & Battery Installation

01. Select cooling cycle rate Battery Installation

The FA setting is used to produce shorter cooling cycles. The SL setting produces a longer cooling
cycle. Both settings produce very accurate temperature control and can be set to your personal
preference. Important:
High quality alkaline batteries are recommended. Rechargeable batteries or low quality batteries do
02. Select heating cycle rate not guarantee 1-year life span.
The FA setting is used to produce shorter heating cycles. The SL setting produces a longer a longer
heating cycle. Both setting produce very accurate temperature control and can be to your personal
preference.

03. Select °F or °C readout

Changes the display readout to Centigrade or Fahrenheit as required. The default setting is "°F".

04. Select compressor lockout delay

To protect the compressor from short cycling, you can select compressor off-time cycle between O or Insert 2 AA Alkaline
5 minutes. When the thermostat compressor time delay occurs, the Cool On or Heat On display will batteries( not included ).
flash during compressor lockout. The default setting is "5". High quality alkaline
batteries are
05. Select temperature recalibration recommended.
This feature allows you to adjust the displayed room temperature up to 5° higher or lower. Your
thermostat can be accurately calibrated to match your previous thermostat. The current or adjusted
room temperature will be displayed on the display. The default setting is "0".

06. Choose traditional mode or heat pump mode

Users can choose traditional mode or heat pump mode according to your own conditon. When heat
pump mode set, the compressor will be enforced Sminutes delay to restart. Mount Thermostat
07. Choose the reversing valve of the heat pump
Users can choose the reversing valve working on the heat mode or the cool mode. In heat pump
mode, please check the reversing vlave to see whether it is in O or B position, and enter the system
to set reversing valve to the position you need.

08. Intelligent Recovery Option

The thermostat has an intelligent recovery function that brings your room temperature at exactly the
pre-set time by turning on the Heating earlier. Select 1 to activate the intelligent recovery function,
Select Oto deactivate the intelligent recovery function. The default setting is "O''.

09. Heat fan control

This function is the control and choosing for the heat fan. If the user uses the Gas or Oil heating
system, please choose "Gas"(system controls fan operation).lf the user uses the Electric heating
system, please choose "Electric"(thermostat controls fan operation).
Step 1: Aim at the inner snaps in Step 2: Hang the two hooks of the Step 3: Press the lower part of the front
the higher part of the thermostat. front part at 30°right to the snaps. display panel to complete the installation.

8.4 Restore factory settings

When power off, hold " FAN " key for 8 seconds. Symbol " dEF " displayed in the clock area shows
restoring factory setting is successful, and press" RUN" key to exit. A In Step 3, if the user think it is hard to connect the pin, please move the display panel slightly.
Then it will be work.

■I■ ■