DESIGN CALCULATIONS Page 1 of 6
DESIGN CALCULATIONS
File Type : Slab
Project Name : 5730
Client Name : IOCL
Engineer Name : YATENDRA TYAGI
Design File : E:\E Drive\LOCAL DISK-E\5730\DESIGN\TANK DESIGN\11-T-101\REV-B\TOP SLAB DESIGN.RCFX
Analysis File : E:\\E Drive\\LOCAL DISK-E\\5730\\DESIGN\\TANK DESIGN\\11-T-101\\REV-B\\11-T-101.STD
Analysis Last Modified : 15-10-2024 11:32:39
Definitions Of Terms:
Maximum spacing of main steel is smaller of 3*Deff. and 300 mm.
Maximum spacing of Distribution steel is smaller of 5*Deff and 450 mm.
All forces in units kN and m
1 a1i = Critical section dimension parallel to moment
2 a2i = Critical section dimension transverse to moment
3 acr = Distance from the point considered to the surface of the
nearest longitudinal bar in mm
4 acs = Deflection due to Shrinkage
5 alpha1 = Moment transfer factor along major direction
6 alpha2 = Moment transfer factor along minor direction
7 Astx C = Area of reinforcement on Compression face in X direction
8 Astx T = Area of reinforcement on tension face in X direction
9 Asty C = Area of reinforcement on Compression face in Y direction
10 Asty T = Area of reinforcement on tension face in Y direction
11 barea = Effective punching area in sqmm
12 Bc = Column/Wall Length to width ratio
13 bcDp = Dp length to width ratio
14 bpm = Effective punching perimeter in mm
15 CiCr = Correction factor for Creep deflection
16 CiDL = Correction factor for Instantaneous Dead Load Deflection
17 CiTL = Correction factor for Instantaneous Total loads Deflection
18 COLb = Column/ wall Minor dimension
19 COLd = Column/ wall Major dimension
20 Delta DL = Deflection due to Dead Loads
21 Delta TL = Deflection due to Total Loads
22 DeltaC = Deflection due to Creep
23 DeltaIDL = Deflection due Instantaneous Dead Load
24 DeltaITL = Deflection due to Instantaneous TL
25 DeltaLT = Deflection due to Total Long term Deflection
26 DeltaS = Deflection due to Shrinkage
27 DPd = Overall depth of DP in mm
28 DPdeff = Effective depth of DP in mm
29 DPx = Length of Drop Panel x Direction in mm
30 DPy = Width of Drop Panel y Direction in mm
31 Ec = Modulus of elasticity of concrete in N/sqmm
32 Es = Modulus of elasticity of steel in N/sqmm
33 Fc = Maximum Compressive Stress in the concrete
34 Fck = Characteristic compressive strength of concrete cube in
N/sqmm
35 Fst = Stress in steel in N/sqmm
36 Fy = Yield Stress of Reinforcement in N/sqmm
37 Icr = Moment of Inertia of Cracked Section
38 Igr = Gross moment of Inertia in mm
39 Ieff = Effective Moment of Inertia
40 Jxx1 = Moment of inertia about centroid of the section in major
direction (as per table no.8, SP24) in mm4
41 Jxx2 = Moment of inertia about centroid of the section in minor
direction (as per table no.8, SP24) in mm4
42 Ks = Shear factor for Colun/Wall size
43 Mshear1 = Part of unbalanced moment transferred to shear in major
direction of Column/Wall in kN-m
44 Mshear2 = Part Of unbalanced moment transferred To shear In minor
direction Of Column/Wall In kN-m
45 Mu2 = Factored bending moment In minor direction Of column/
wall In kN-m/m
46 Mu3 = Factored bending moment In major direction Of column/
wall In kN-m/m
file:///C:/Users/Yatendra%20tyagi/AppData/Local/Temp/tmp5FF.tmp 15-10-2024
DESIGN CALCULATIONS Page 2 of 6
47 MubotCS = Design bending moment at bottom along length In CS from
analysis In kN-m/m
48 MutopCS = Design bending moment at top across length In CS from
analysis In kN-m/m
49 Mux = Design moment along X direction In kN-m/m
50 Mux CSJ = Design bending moment at top along X direction In CSJ from
analysis In kN-m/m
51 Mux DP = Design bending moment at top along X direction In DP from
analysis In kN-m/m
52 Mux.Design DP = Final design bending moment at top along X direction In DP
including effect Of unbalanced bending moment
Mux.DP + Ubm1 Or Ubm2 In kN-m/m
53 MuxbotMS = Design bending moment at bottom along X direction In MS
from analysis In kN-m/m
54 Muy = Design moment along Y direction In kN-m/m
55 Muy CSJ = Design bending moment at top along Y direction In CSJ from
analysis In kN-m/m
56 Muy DP = Design bending moment at top along Y direction In DP from
analysis In kN-m/m
57 Muy.Design DP = Final design bending moment at top along Y direction In DP
including effect Of unbalanced bending moment
Muy.DP + Ubm1 Or Ubm2 In kN-m/m
58 MuybotMS = Design bending moment at bottom along Y direction In MS
from analysis In kN-m/m
59 MxDL = Moment due To DL In X direction For the location Of
maximum deflection
60 MxLL = Moment due To LL In X direction For the location Of maximum
deflection
61 MyDL = Moment due To DL In Y direction For the location Of
maximum deflection
62 MyLL = Moment due To LL In Y direction For the location Of maximum
63 Ptx C = Percentage reinforcement On Compression face In X
direction
64 Ptx T = Percentage reinforcement On tension face In X direction
65 Pty C = Percentage reinforcement On Compression face In Y
direction
66 Pty T = Percentage reinforcement On tension face In Y direction
67 Pu = Factored axial load In column/Wall In kN
68 SLdeff = Effective depth Of Slab In mm
69 sp = Spacing Between bars at outer most layer In mm
70 Tc = Permissible Shear stress In concrete In N/sqmm
71 TceDp = Final Concrete Shear Stress Of Dp In N/sqmm
72 Tce = Final Concrete Shear Stress In N/sqmm
73 Tshear1 = Shear Stress Deu To unbalanced moment along major
direction In N/sqmm
74 Tshear2 = Shear Stress Deu To unbalanced moment along minor
direction In N/sqmm
75 Tv = Maximum design punching shear stress For Column/Wall In
N/sqmm
76 TvDp = Maximum Design punching shear Stress For Dp In N/sqmm
77 Ubm1 = Part Of unbalanced moment transferred To bending moment
In major direction Of Column/Wall In kN-m
78 Ubm1T = Total unbalanced moment transferred To bending moment In
major direction Of Column/Wall InkN-m
79 Ubm2 = Part Of unbalanced moment transferred To bending moment
In minor direction Of Column/Wall In kN-m
80 Ubm2T = Total unbalanced moment transferred To bending moment In
minor direction Of Column/Wall In kN-m
81 Vc = Shear resisted by Concrete In kN
82 VuShear = Shear Stress due To Vertical load In N/sqmm
83 Vcr = Design shear force at critical section from the face Of the
column/Wall In kN
84 VcrDp = Design shear force at critical section from the face Of the DP
In kN
85 ksDp = Shear Stress Factor Of DP
86 Vs = Shear resisted by shear reinforcement In kN
87 Wcr = Surface Crack Width In mm
88 Wu = Ultimate loading intensity On DP/ CSJ In kN/sqm
89 Xact = Actual depth Of natural axis
90 ycs = Shrinkage curvature
91 ε 1 = Strain at the level considered, calculated ignoring the
stiffening of the concrete in the tension zone
92 ε m = Average steel strain at the level considered
file:///C:/Users/Yatendra%20tyagi/AppData/Local/Temp/tmp5FF.tmp 15-10-2024
DESIGN CALCULATIONS Page 3 of 6
93 εcs = Ultimate shrinkage strain of concrete
Code Reference
IS 456
Element Clause / table
1 Ptmin = 26.5.2.1
2 Ptcalculated = 38
3 Shear Strength Of Concrete = 40.3
4 Modification Factor for Shear = 40.2.1.1
5 Max Nominal Shear Stress = 40.2.3
6 Basic Span To Depth Ratio = 23.2.1
7 Spacing Between Main Bars = 26.3.3
8 Spacing Between Distribution Bars = 26.3.3
9 Transfer Of Bending Moment To Column//Wall = 31.3.3
10 Shear In Flat Slab = 31.6
11 Flat Slab Reinforcement = 31.7
12 Calculation Of Deflection = Annex-C
13 Crack Width Calculation = Annex-F
14 Cracking of Concrete = Clause 35.3.2
15 Short Term Deflection = Annex-C, C-2
16 Ieff = Annex-C,C-2.1
17 Deflection Due To Shrinkage = Annex-C, C-3
18 Deflection Due to Creep = Annex-C, C-4
General Data:
Region = S1
Design Code = IS 456
Grade Of Concrete = M30
Grade Of Steel = Fe500
Clear cover Top = 25 mm
Clear cover Bottom = 25 mm
TopX
Through
Critical Load Combination = -
SLdeff = 169 mm
Mux = 0 kN-m/m
Ast Required = 200 sqmm/m
Ast Provided = 523.6 sqmm/m
Reinforcement = T10@150C/C (MESH)
TopY
Through
Critical Load Combination = -
SLdeff = 157 mm
Muy = 0 kN-m/m
Ast Required = 200 sqmm/m
Ast Provided = 523.6 sqmm/m
Reinforcement = T10@150C/C (MESH)
BottomX
Through
Critical Load Combination = -
SLdeff = 169 mm
Mux = 0 kN-m/m
Ast Required = 200 sqmm/m
Ast Provided = 523.6 sqmm/m
Reinforcement = T10@150C/C (MESH)
BottomY
Through
Critical Load Combination = -
SLdeff = 157 mm
Muy = 0 kN-m/m
Ast Required = 200 sqmm/m
file:///C:/Users/Yatendra%20tyagi/AppData/Local/Temp/tmp5FF.tmp 15-10-2024
DESIGN CALCULATIONS Page 4 of 6
Ast Provided = 523.6 sqmm/m
Reinforcement = T10@150C/C (MESH)
General Data:
Region = S2
Design Code = IS 456
Grade Of Concrete = M30
Grade Of Steel = Fe500
Clear cover Top = 25 mm
Clear cover Bottom = 25 mm
TopX
Through
Critical Load Combination = -
SLdeff = 169 mm
Mux = 0 kN-m/m
Ast Required = 200 sqmm/m
Ast Provided = 523.6 sqmm/m
Reinforcement = T10@150C/C (MESH)
TopY
Through
Critical Load Combination = -
SLdeff = 157 mm
Muy = 0 kN-m/m
Ast Required = 200 sqmm/m
Ast Provided = 523.6 sqmm/m
Reinforcement = T10@150C/C (MESH)
BottomX
Through
Critical Load Combination = -
SLdeff = 169 mm
Mux = 0 kN-m/m
Ast Required = 200 sqmm/m
Ast Provided = 523.6 sqmm/m
Reinforcement = T10@150C/C (MESH)
BottomY
Through
Critical Load Combination = -
SLdeff = 157 mm
Muy = 0 kN-m/m
Ast Required = 200 sqmm/m
Ast Provided = 523.6 sqmm/m
Reinforcement = T10@150C/C (MESH)
General Data:
Region = S3
Design Code = IS 456
Grade Of Concrete = M30
Grade Of Steel = Fe500
Clear cover Top = 25 mm
Clear cover Bottom = 25 mm
TopX
Through
Critical Load Combination = -
SLdeff = 169 mm
Mux = 0 kN-m/m
file:///C:/Users/Yatendra%20tyagi/AppData/Local/Temp/tmp5FF.tmp 15-10-2024
DESIGN CALCULATIONS Page 5 of 6
Ast Required = 200 sqmm/m
Ast Provided = 523.6 sqmm/m
Reinforcement = T10@150C/C (MESH)
TopY
Through
Critical Load Combination = -
SLdeff = 157 mm
Muy = 0 kN-m/m
Ast Required = 200 sqmm/m
Ast Provided = 523.6 sqmm/m
Reinforcement = T10@150C/C (MESH)
BottomX
Through
Critical Load Combination = -
SLdeff = 169 mm
Mux = 0 kN-m/m
Ast Required = 200 sqmm/m
Ast Provided = 523.6 sqmm/m
Reinforcement = T10@150C/C (MESH)
BottomY
Through
Critical Load Combination = -
SLdeff = 157 mm
Muy = 0 kN-m/m
Ast Required = 200 sqmm/m
Ast Provided = 523.6 sqmm/m
Reinforcement = T10@150C/C (MESH)
General Data:
Region = S4
Design Code = IS 456
Grade Of Concrete = M30
Grade Of Steel = Fe500
Clear cover Top = 25 mm
Clear cover Bottom = 25 mm
TopX
Through
Critical Load Combination = -
SLdeff = 169 mm
Mux = 0 kN-m/m
Ast Required = 200 sqmm/m
Ast Provided = 523.6 sqmm/m
Reinforcement = T10@150C/C (MESH)
TopY
Through
Critical Load Combination = -
SLdeff = 157 mm
Muy = 0 kN-m/m
Ast Required = 200 sqmm/m
Ast Provided = 523.6 sqmm/m
Reinforcement = T10@150C/C (MESH)
BottomX
Through
Critical Load Combination = -
SLdeff = 169 mm
Mux = 0 kN-m/m
Ast Required = 200 sqmm/m
file:///C:/Users/Yatendra%20tyagi/AppData/Local/Temp/tmp5FF.tmp 15-10-2024
DESIGN CALCULATIONS Page 6 of 6
Ast Provided = 523.6 sqmm/m
Reinforcement = T10@150C/C (MESH)
BottomY
Through
Critical Load Combination = -
SLdeff = 157 mm
Muy = 0 kN-m/m
Ast Required = 200 sqmm/m
Ast Provided = 523.6 sqmm/m
Reinforcement = T10@150C/C (MESH)
file:///C:/Users/Yatendra%20tyagi/AppData/Local/Temp/tmp5FF.tmp 15-10-2024
