Top Drive Drilling Equipment

Hydraulic Drawing
Model DQ70BSC

Serial No 06032
 Preface
The design, manufacture and service of this product are based on the following quality
assurance system:

GB/T19001:2000 idt ISO9001:2000 « Quality Management System-- Requirements»

API Spec Q1« Specification for Quality Programs for the Petroleum and Natural Gas Industry»

This manual contains information relating to Top Drive operation, service and maintenance.
The technical information of this product is included respectively in the following documents:
<Operation Manual>

<Electric Manual>

<Hydraulic Manual>

< Installation and Trouble Shooting Manual>

<Maintenance Manual>

<Electric House Manual>

<HSE Manual>

<Data Backup and Recovery Manual>

<Electric Drawing>

<Mechanical Drawing>

<Hydraulic Drawing>

With individualized design provided for the Top Drive based on the service operating
condition and special requirements of the customers, the technical document for this product
may not be suitable for the other products of the same type. Product type and No. shall be
checked when the technical document is used.

For information not covered by the accompanying documents and other problems arising
from the installation, operation and maintenance, contact the manufacturer if necessary:

BPM Beijing Petroleum Machinery Factory

Ads: No.41, Zhixin Road, Haidian District, Beijing P.R China

Postcode: 100083

Tel: ( 010) 62097381

Fax: ( 010) 62097613

E-mail: [email protected]

-I-
 CONTENTS

1. HYDRAULIC SYSTEM ................................................................................................1

2. UPPER HYDRAULIC CONTROL SYSTEM ................................................................2

3. HYDRAULIC VALVE MANIFOLD ..............................................................................3

4. HYDRAULIC VALVE MANIFOLD LIST....................................................................4

5. BACKUP TONG SYSTEM............................................................................................5

6. IBOP SYSTEM...............................................................................................................6

7. TILT SYSTEM................................................................................................................7

8. ROTARY LOCKING SYSTEM .....................................................................................8

9. IBOP CYLINDER ..........................................................................................................9

10. ACCUMULATOR BANK............................................................................................10

11. ACCUMULATOR VALVE BLOCK ............................................................................11

12. LINK TILT CYLINDER...............................................................................................12

13. ROTARY SYSTEM ......................................................................................................13

14. BALANCE SYSTEM .................................................................................................14

15. BALANCE CYLINDER ..............................................................................................15

16. HYDRAULIC LINE.....................................................................................................16

17. EXTENDED LOOP......................................................................................................17

18. SERVICE LOOP...........................................................................................................18

19. LOWER IBOP ..............................................................................................................19

20. UPPER IBOP ................................................................................................................20

21. IBOP CONTROL DEVICE LOCATION MAP ...........................................................21

22. ROTARY LOCKING OIL CYLINDER .......................................................................22

 Ⅱ
PC2 PC1
K 1:10
PD2 PD1
1:10

BB1(4)
Ⅰ BB2(4)
BA2(5)
B1
L1

T1

P1

4
K
10 9 6 5 8 7
BA1(5) 5

BB2(4) BA2(5)
5 BA3 hose assembly 9705224007 F381CFCF151508-2900X0° 1 BA2-BA3
Ⅱ 4 BB3 hose assembly 9705224006 F381CFCF151508-2710X0° 1 BB2-BB3
3 68 Joint 9705222008 2 Borrow
2 BB1 hose assembly 9705224002 F381CFCF151508-3130X270° 1 BB-BB1
1 BA1 hose assembly 9705224001 F381CACF151508-2540X315° 1 BA-BA1
Ⅰ
1:2 B1 Adjustable joint 5202000530 WEE15LMOMDA3C 4
BA No. Name Type(or Drawing No) Specification Qty. Standard Symbol
Drawing
material
Number
9705222000
BB
Mark Qty. Section Modify No. Signature Date Save No. Backup Tong
Name
Design Standardization
Period mark Weight Rate system
Drawing Authorize
Verify Beijing Petroleum Machinery
Craft page 5 of 22 Factory
 Ⅰ
1:2 Ⅳ（backsight） 4
1:3
PD2 PD1

FA Ⅰ
B2 FB2 FA2 5

FB B1 6
L1

T1

P1
1
7
2 B6
Ⅱ 8
1:5

FB4 FA4 9
3 10
Ⅱ
Ⅲ
1:3
Ⅲ
FB1(10) FA1(7)
11

B3 12
13 FB4 hose assembly 9705223010 F381CFCA151508-270 1 FB4
12 FA4 hose assembly 9705223009 F381CFCA151508-285 1 FA4
11 FA34 hose assembly 9705223008 F381CACA151508-650 1 FA3-FA4 B4 13
10 FB34 hose assembly 9705223007 F381CACA151508-665 1 FB3-FB4
9 IBOP cylinder 9705225200 2
8 FA3 hose assembly 9705223006 F381CFCA151508-285 1 FA3 B5
7 FB3 hose assembly 9705223005 F381CFCA151508-280 1 FB3
6 FA2 hose assembly 9705223004 F381CACA151508-680 1 FA2 FB3
5 FB2 hose assembly 9705223003 F381CACA151508-715 1 FB2 FA3
4 71 joint 9705214003 35 2 Borrow
3 93 joint 9705213002 35 2 Borrow
2 FB1 hose assembly 9705223002 F381CFCF151508-2570X0° 1 FB-FB1 Drawing
1 FA1 hose assembly 9705223001 F381CFCF151508-2620X0° 1 FA-FA1 material 9705223000
Number
B6 Feed through joint 5202000450 GE15LMEDOMDA3C 4 ParKer
B5 Compact seal 5304010040 18 4 JB/T982-1997 Mark Qty. Section Modify No. Signature Date Save No.
B4 Hexagonal bolt 5202000560 M18X1.5 4 JB/ZQ4444-1997 Design
Name IBOP system
B3 Three way joint 5202000500 T15LA3C 2 ParKer
Standardization
Period mark Weight Rate
Drawing Authorize
B2 Joint 5202000430 SWVE15LMOMDA3C 2 ParKer
B1 Right angle joint 2 ParKer Verify Beijing Petroleum Machinery
5202000401 W15LA3C
No. Name Specification Qty Standard symbol Remark Craft page 6 of 22 Factory
 Ⅰ PC2 PC1

1:2
PD2 PD1

QA

1
QB
2
Ⅰ f low c on tro l va lve
L1

T1

P1
11 970 52 24 011 2
10 li nk ti lt cy cl in der 970 52 27 200 2
9 6 8 j oi nt 970 52 22 008 2
8 QA 8 hos e as sem bl y 970 52 24 014 F3 81C FC F15 15 08 -87 0 2
7 QB 8 hos e as sem bl y 970 52 24 010 F3 81C FC F15 15 08 -87 0 2
3
Ⅲ 6 QB 6 hos e as sem bl y 970 52 24 006 F 38 1C ACF 15 15 08- 35 0 1
1:10 5 QA 6 hos e as sem bl y F 38 1C ACF 15 15 08- 35 0 1
B6 4 970 52 24 005
4 QB 5 hos e as sem bl y 970 52 24 004 F 38 1CA CF 15 150 8- 43 5 1
QB6 QB6 3 QA 5 hos e as sem bl y 970 52 24 003 F 38 1CA CF 15 150 8- 10 80 1
QA6 K 2 QB 1 hos e as sem bl y 970 52 24 013 F3 81 CFC F1 51 508 -3 07 0 1
QA6 5
Ⅲ FB1(10) BA(5) FA1(7) 1 QA 1 hos e as sem bl y 970 52 24 012 F3 81 CFC F1 51 508 -3 11 0 1
B7
B8 B5 6
B8 Feed through compact joint 5202000490 EGE15LMEDA3C 2
Backsight
QB8 QB8 B7 Three way joint 5202000500 T15LA3CX 2
B4 7 B6 Feed through joint GE15LMEDOMDA3C 11
QA5(3) 11 5202000450
每组由两个二通流量控制阀
B5 Compositive valve B 5126000701 QV-06/24/60组成 2
QA8 QA8 B4 Adjustable joint 5202000530 WEE15LMOMDA3C 1
10 8 B2 Standard spring collar 4205030040 8 8 GB/T93-1987
B2
B1 Hexagonal bolt 4202000180 M8X70 8 GB/T32.1-1988
B1 Remark
No. Name Type Specification Qty Standard symbol
Direction K 9
Ⅱ Drawing
Ⅱ 1:5 material 9705224000
Number
Mark Qty. Section Modify No. Signature Date Save No.
Name Tilt system
Design Standardization
Period mark Weight Rate
Drawing Authorize
QA4(3) QB4(2)
Verify Beijing Petroleum Machinery
Craft page 7 of 22 Factory
 K
1:4 B2
B1
B3

6
PC2 PC1
B4
PD1
PD2
B5 B6
1
XP1
XA B7 B8
2 XT1 XB
7

XT 7 Shot pin valve block bottom plate 9705225005 1

XP 6 Shot pin valve block 9705225005 1
5 Shot-pin cylinder 9705216100 1
4 XB hose assembly 9705225004 F381CFCF151508-560X0° 1 XB-XB1
3 XA hose assembly 9705225003 F381CFCF151508-570X0° 1 XA-XA1
2 XP hose assembly 9705225002 F381CFCA151508-2740 1 XP-XP1
1 XT hose assembly 9705225001 F381CFCA151508-2780 1 XT-XT1
B8 Spring collar 4205030030 6 4 GB/T93-1987
B7 Hexagon socket head cap screw 4201120061 M6X16 4 GB/T70.1-2000
3 B6 Spring collar 4205030040 8 4 GB/T93-1987
4 B5 Hexagonal bolt 4202000143 M8X35 4 GB5782/T-2000
B4 Pressure measure joint 5202000440 M14X1.5 (CSH M14X1.5) 2
5 B3 Reduce valve 5126000480 1 REXROTH
B2 Two port, four way explosion proof magnetic valve 5126000562 1 REXROTH
K XA1 B1 Feed through joint 5202000450 GE15LMEDOMDA3C 7 ParKer
XB1
No. Name Type Specification Qty Standard symbol
Drawing
material 9705225000
Number
Mark Qty. Section Modify No. Signature Date Save No.
Name Rotary locking cylinder
Design Standardization
Period mark Weight Rate
Drawing Authorize
Verify Beijing Petroleum Machinery
Craft page 8 of 22 Factory
115
 Ⅰ(K) Ⅱ
PC2 PC1 1:2 1:2

PD2 PD1
Ⅰ HL
HA

Ⅱ
K HB

L1
1
T1

P1

Ⅲ
2 1:5

HB1
3
HA1

B1 HL1

B2

Ⅲ
4 Joint 9705216004 35
3 HL hose assembly 9705228003 F381CFCF151508-3150X225° 1 HL-HL1
2 HB hose assembly 9705228002 F381CFCF151508-2780X270° 1 HB-HB1
1 HA hose assembly 9705228001 F381CFCF151508-2805X270° 1 HA-HA1
B2 Compact seal 5304010130 14 1 JB/T982-1977
B1 Feed through joint 5202000520 GE15ZLR3/4EDOMDA3C 2
No. Name Type Specification Qty Standard symbol Remark
Drawing
material
Number
9705228000
Mark Qty. Section Modify No. Signature Date Save No.
Design Standardization
Period mark Weight Rate
Name Rotary system
Drawing Authorize
Verify Beijing Petroleum Machinery
Craft page 13 of 22 Factory
 5000 0

28000

1
PDF 文件使用 "pdfFactory Pro" 试用版本创建 www.fineprint.com.cn