AUTOCLAVE

An autoclave is a machine that provides a physical method of

sterilization by killing bacteria, viruses, and even spores present
in the material put inside of the vessel using steam under pressure.
Autoclave sterilizes the materials by heating them up to a particular
temperature for a specific period of time. The autoclave is also
called a steam sterilizer that is commonly used in healthcare
facilities and industries for various purposes. The autoclave is
considered a more effective method of sterilization as it is based on
moist heat sterilizationEerie Aurora Looks Like a Glowing Necklace in
the Sky

Autoclave Parts/ Components

The simplest form of the autoclave is the pressure cooker type or
laboratory bench autoclaves. The following is the detailed
description of different components/ parts of an autoclave:

Figure: Autoclave Parts or

Components. Image Source: pharmawiki.
a. Pressure Chamber
 The pressure chamber is the main component of a steam
autoclave consisting of an inner chamber and an outer jacket.
 The inner chamber is made up of stainless steel or gunmetal,
which is present inside the out chamber made up of an iron case.
 The autoclaves used in healthcare laboratories have an outer
jacket that is filled with steam to reduce the time taken to reach
the sterilization temperature.
 The inner chamber is the case where the materials to be sterilized
are put.
 The size of the pressure chamber ranges from 100 L to 3000 L.
b. Lid/ Door
 The next important component of an autoclave is the lid or door of
the autoclave.
 The purpose of the lid is to seal off the outside atmosphere and
create a sterilized condition on ht inside of the autoclave.
 The lid is made airtight via the screw clamps and asbestos washer.
 The lid consists of various other components like:
Pressure gauge
 A pressure gauge is present on the lid of the autoclave to indicate
the pressure created in the autoclave during sterilization.
 The pressure gauge is essential as it assures the safety of the
autoclave and the working condition of the operation.
Pressure releasing unit/ Whistle
 A whistle is present on the lid of the autoclave is the same as that
of the pressure cooker.
 The whistle controls the pressure inside the chamber by releasing
a certain amount of vapor by lifting itself.
Safety valve
 A safety valve is present on the lid of the autoclave, which is
crucial in cases where the autoclave fails to perform its action or
the pressure inside increases uncontrollably.
 The valve has a thin layer of rubber that bursts itself to release the
pressure and to avoid the danger of explosion.
c. Steam generator/ Electrical heater
 An electrical steam generator or boiler is present underneath the
chamber that uses an electric heating system to heat the water
and generate steam in the inner and the outer chamber.
 The level of water present in the inner chamber is vital as if the
water is not sufficient; there are chances of the burning of the
heating system.
 Similarly, if the water is more than necessary, it might interfere
with the trays and other components present inside the chamber.
d. Vacuum generator (if applicable)
 In some types of autoclaves, a separate vacuum generator is
present which pulls out the air from the inside of the chamber to
create a vacuum inside the chamber.
 The presence of some air pockets inside the chamber might
support the growth of different microorganisms. This is why the
vacuum chamber is an important component of an autoclave.
e. Wastewater cooler
 Many autoclaves are provided with a system to cool the effluent
before it enters the draining pipes.
 This system prevents any damage to the drainage pipe due to the
boiling water being sent out of the autoclave.
Autoclave Principle/ Working
 Figure: Autoclave Principle or Working.
 The autoclave works on the principle of moist heat sterilization
where steam under pressure is used to sterilize the material
present inside the chamber.
 The high pressure increases the boiling point of water and thus
helps achieve a higher temperature for sterilization.
 Water usually boils at 100°C under normal atmospheric pressure
(760 mm of Hg); however, the boiling point of water increases if
the pressure is to be increased.
 Similarly, the high pressure also facilitates the rapid penetration of
heat into deeper parts of the material, and moisture present in the
steam causes the coagulation of proteins causing an irreversible
loss of function and activity of microbes.
 This principle is employed in an autoclave where the water boils at
121°C at the pressure of 15 psi or 775 mm of Hg.
 When this steam comes in contact with the surface, it kills the
microbes by giving off latent heat.
 The condensed liquid ensures the moist killing of the microbes.
 Once the sterilization phase is completed (which depends on the
level of contamination of material inside), the pressure is released
from the inside of the chamber through the whistle.
 The pressure inside the chamber is then restored back to the
ambient pressure while the components inside remain hot for
some time.

Procedure for running an autoclave

In general, an autoclave is run at a temperature of 121° C for at
least 30 minutes by using saturated steam under at least 15 psi of
 pressure. The following are the steps to be followed while running
an autoclave:
1. Before beginning to use the autoclave, it should be checked for
any items left from the previous cycle.
2. A sufficient amount of water is then put inside the chamber.
3. Now, the materials to be sterilized are placed inside the chamber.
4. The lid is then closed, and the screws are tightened to ensure an
airtight condition, and the electric heater is switched on.
5. The safety valves are adjusted to maintain the required pressure in
the chamber.
6. Once the water inside the chamber boils, the air-water mixture is
allowed to escape through the discharge tube to let all the air
inside to be displaced. The complete displacement can be ensured
once the water bubbles cease to come out from the pipe.
7. The drainage pipe is then closed, and the steam inside is allowed
to reach the desired levels (15 lbs in most cases).
8. Once the pressure is reached, the whistle blows to remove excess
pressure from the chamber.
9. After the whistle, the autoclave is run for a holding period, which is
15 minutes in most cases.
10. Now, the electric heater is switched off, and the autoclave is
allowed to cool until the pressure gauge indicates the pressure
inside has lowered down to that of the atmospheric pressure.
11. The discharge pipe is then opened to allow the entry of air
from the outside into the autoclave.
12. Finally, the lid is opened, and the sterilized materials are taken
out of the chamber.

Types of Autoclave
There are different types of autoclaves present in the market, some
of which are:
Pressure cooker type/ Laboratory bench
autoclaves (N-type)
 These, as domestic pressure cookers, are still in use in many parts
of the world.
 The more modern type has a metal chamber with a secure metal
lid that can be fastened and sealed with a rubber gasket.
 It has an air and steam discharge tap, pressure gauge, and safety
valve. There is an electric immersion heater at the bottom of the
chamber.
Gravity displacement type autoclave
 This is the common type of autoclave used in laboratories.
 In this type of autoclave, the steam is created inside the chamber
via the heating unit, which then moves around the chamber for
sterilization.
 This type of autoclave is comparatively cheaper than other types.
Positive pressure displacement type (B-type)
 In this type of autoclave, the steam is generated in a separate
steam generator which is then passed into the autoclave.
 This autoclave is faster as the steam can be generated within
seconds.
 This type of autoclave is an improvement over the gravity
displacement type.
Negative pressure displacement type (S-
type)
 This is another type of autoclave that contains both the steam
generator as well as a vacuum generator.
 Here, the vacuum generator pulls out all the air from inside the
autoclave while the steam generator creates steam.
 The steam is then passed into the autoclave.
 This is the most recommended type of autoclave as it is very
accurate and achieves a high sterility assurance level.
 This is also the most expensive type of autoclave.
 Figure: Types of Autoclaves. Image Source: Microbe Online.
Uses of Autoclave
Autoclaves are important devices to ensure the sterilization of
materials containing water as they cannot be sterilized by dry heat
sterilization. Besides, autoclaves are used for various other
purposes.
1. They are used to decontaminate specific biological waste and
sterilize media, instruments, and labware.
2. Regulated medical waste that might contain bacteria, viruses, and
other biological materials is recommended to be inactivated by
autoclaving before disposal.
3. In medical labs, autoclaves are used to sterilize medical
equipment, glassware, surgical equipment, and medical wastes.
4. Similarly, autoclaves are used for the sterilization of culture media,
autoclavable containers, plastic tubes, and pipette tips.
Precautions
Although autoclaves are pretty simple to use, there are certain rules
of precautions to be followed while operating an autoclave. Some of
the important precautions to be followed while running an autoclave
are:
1. Autoclaves should not be used to sterilize water-proof or water-
resistant substances like oil or powders.
2. The autoclave should not be overcrowded, and the materials
should be loaded in a way that ensures sufficient penetration of
articles by the steam.
3. The items to be autoclaved should always be placed in a
secondary container.
4. Only autoclavable bags are to be used to autoclave packaged
waste.
5. To ensure sufficient penetration, articles should be wrapped in
something that allows penetration by steam, and materials like
aluminum foils should not be used.
6. The items placed inside the chamber should not touch the sides or
top of the chamber.
7. The wastes and clean items should be autoclaved separately.
8. Attempts to open the lid when the autoclave is working should
never be made.
9. Liquid components should never be autoclaved in sealed
containers.
10. The liquid inside the containers should only be filled 2/3 rd of the
total volume to prevent the spilling of the liquid.