Total No. of Questions : 8] SEAT No.
8
23
PB3602 [Total No. of Pages : 3
[6261]-7
ic-
tat
S.E. (Civil Engineering)
5s
MECHANICS OF STRUCTURE
6:0
(2019 Pattern) (Semester-III) (201002)
02 91
4:1
0
Time : 2½ Hours] [Max. Marks : 70
41
7/0 13
Instructions to the candidates:
0
1) Solve Q1 or Q2, Q3 or Q4, Q5 or Q6, Q7 or Q8.
5/2
.23 GP
2) Assume suitable data, if necessary.
3) Use of Non-programmable calculator is allowed.
E
81
8
C
23
Q1) a) A simply supported beam of rectangular cross section, 350mm wide
ic-
and 700mm deep is subjected to uniformly distributed load of 120kN/m
16
tat
on entire span of 3m.
8.2
5s
Determine maximum bending stress and draw Bending stress Distribution
.24
6:0
diagram. [8]
91
49
4:1
b) A ‘T’ beam is having flange 1000mm×100mm and web
30
41
800mm × 80mm. The maximum shear force induced in the beam due to
01
02
applied load is 400 KN. Draw shear strees distribution diagram for the
5/2
beam. [9]
GP
7/0
OR
CE
81
8
Q2) a) A cantilever beam of span 1.2m is loaded with a point load of 70KN at
23
.23
its free end. The beam is rectangular in cross section having width 230mm
and depth 500mm. Determine maximum bending stress & draw bending ic-
16
tat
stress distribution diagram. [8]
8.2
5s
b) A symmetric ‘I’ section having
.24
6:0
91
49
flanges - 500mm × 25mm
4:1
30
web - 800mm × 20mm.
41
01
02
Maximum shear force induced in the beam due to applied loading is
5/2
300KN. Draw shear stress distribution diagram. [9]
GP
7/0
CE
81
Q3) a) A hollow circular shaft has an external diameter of 120mm and an internal
diameter of 100mm. The maximum permissible shear stress is 80 MPa
.23
and the twist is not to exceed 3º in length of 3m. The shaft is rotating at
16
2RPS if the shear modulus of the material is 80 GPa, find the safe power
8.2
that can be transmitted. [9]
.24
49
P.T.O.
8
b) At a point in a material the stress on two mutually perpendicular plane
23
are 140N/mm2 and 70 N/mm2, both tensile. Determine normal, tangential
ic-
and resultant stress at a plane 20º to the major principal plane. [8]
tat
5s
OR
6:0
02 91
Q4) a) Find maximum torque that can be applied to a shaft of 100mm diameter.
4:1
The permissible angle of twist is 1.2º in a length of 3m and permissible
0
41
shear stress is 70 MPa.
7/0 13
0
G = 80 GPa [9]
5/2
.23 GP
b) An element is subjected to a tensile stress of 120 MPa and a shear strees
of 60 MPa tending to rotate the element in an anticlockwise direction.
E
81
8
C
23
Determine the magnitude of normal and shear stress on a section inclined
ic-
at 35º with the tensile stress. [8]
16
tat
8.2
5s
.24
6:0
Q5) a) A hollow circular column with two ends hinged carrying 10kN axial load.
91
49
4:1
If the outer diameter of the column is 60mm. The column is 6m long.
30
Determine the inner diameter of the column. Factor of safety 2 against
41
buckling. E = 80 GPa. [6]
01
02
5/2
b) Determine the crippling load for a hollow rectangular cast iron column of
GP
7/0
outer dimensions 300mm × 200mm. Thickness of the column is 30mm.
CE
The length of the column is 5m having one end fixed and other hinged.
81
8
23
E= 160 GPa. [6]
.23
c) A rectangular column 600mm × 400mm is subjected to compressive ic-
16
tat
load of 200kN acting at an eccentricity of 50mm in a plane bisecting
8.2
5s
400mm side. Determine maximum and minimum stresses. [6]
.24
6:0
91
OR
49
4:1
30
41
Q6) a) A steel rod 5m long and 100mm diameter is acting as column with one
end fixed and other free. Find crippling load by Euler’s formula consider
01
02
E = 210 GPa [6]
5/2
GP
7/0
b) A hollow column, 4m long is fixed at both ends. The external diameter
CE
of the column is 350mm and thickness is 25mm. Determine Rankine’s
81
.23
1
crippling load. taking fc = 550 N/mm2 and [7]
1700
16
8.2
c) Determine the core of section for a circular section of diameter ‘D’. [5]
.24
[6261]-7 2
49
Q7) a) Determine maximum slope and central deflection for a simply supported
8
23
beam as shown below. Use Macaulay’s method. [9]
ic-
tat
5s
6:0
02 91
4:1
0
41
7/0 13
b) Determine the vertical displacement at joint C by using unit load method
0
5/2
Area of the each member of the truss is 400mm2. E = 210 GPa [9]
.23 GP
E
81
8
C
23
ic-
16
tat
8.2
5s
.24
6:0
91
49
4:1
30
OR
41
01
02
Q8) a) A cantilever beam of span ‘L’ is subjected to uniformly distributed load
5/2
of ‘w’ kN/m on entire span. Determine slope and deflection at the free
GP
end of the beam, using Macaulay’s method. [9]
7/0
CE
b) Determine horizontal displacement at joint ‘C’. Area of each member of
81
8
23
the truss is 450mm2. E = 200 GPa. [9]
.23
ic-
16
tat
8.2
5s
.24
6:0
91
49
4:1
30
41
01
02
5/2
GP
7/0
CE
81
eeee
.23
16
8.2
.24
[6261]-7 3
49
