CPD-200ES

CPD-200ES
SERVICE MANUAL CPD-200ES
China Model
Chassis [Link]-L16B-A

X2F CHASSIS

SPECIFICATIONS

Picture Tube 0.26 mm aperture grill pitch Standard image area Approx. 312 x 234 mm (w/h)
17 inches measured diagonally (12.3 x 9.3 inches)
90-degree deflection Deflection frequency Horizontal: 31 to 70 KHz
Video image area (15.9" maximum viewing image) Vertical: 50 to 120 Hz
Approx. 327 x 241 mm (w/h) AC input voltage / current 100 to 120 V, 50-60 Hz,1.8 A (max.)
(12.9 x 9.5 inches) 220 to 240 V, 50-60 Hz, 1.0 A
Logical resolution Horizontal: Max. 1280 dots Dimensions 406 x 431.5 x 420 mm (w/h/d)
Vertical: Max. 1024 lines (16 x 17 x 16.5 inches)
Physical resolution Horizontal: Max. 1024 dots Mass Approx. 19.0 kg (41 lb. 13 oz.)
Vertical: Max. 768 lines

Design and specifications are subject to change without notice.

TRINITRON® COLOR COMPUTER DISPLAY

MICROFILM

—1—
CPD-200ES

POWER SAVING FUNCTION

This monitor meets the power saving guidelines set CAUTION: The Power Saving function will automati-
by the EPA Energy Star Program as well as the more cally put the monitor into Active-off state
stringent TC092 guidelines (NUTEK). It is capable of if the power switch is turned on without
reduced power consumption when used with a com- any video signal input. Once the horizon-
puter equipped with Display Power Management Sig- tal and vertical syncs are sensed, the moni-
naling (DPMS). By sensing the absence of the sync tor will automatically return to its Normal
signal coming from the computer, it will reduce the operation state.
power consumption as follows:

State Power Required u Power indicator

consumption resumption time

1 Normal Operation <110 W green on

Suspend orange and green
2 <15 W approx. 3 sec.
(1st step of power saving) flashes alternately
Active-off orange and green
3 <15 W approx. 10 sec.
(2nd step of power saving) flashes alternately

4 Active-off <8 W approx. 10 sec. orange on

(3rd step of power saving)

5 Power - Off 0W off

TIMING SPECIFICATION
Mode 1 2 3 4 5 6 7 8

Resolution(H x V) 640 x 480 640 x 480 800 x 600 800 x 600 832 x 624 1024 x 768 1280 x 1024 1024 x 768
Dot Clock(MHz) 25.175 36.000 49.500 56.250 57.283 78.750 108.000 94.500

Horizontal
Hor. Freq. (kHz) 31.469 43.269 46.875 53.674 49.725 60.023 63.981 68.677
H-Total 31.778 23.111 21.333 18.631 20.111 16.660 15.630 14.561
H-Blanking 6.356 5.333 5.172 4.409 5.586 3.657 3.778 3.725
H-Front Porch 0.636 1.556 0.323 0.569 0.559 0.203 0.444 0.508
H-Sync. 3.813 1.556 1.616 1.138 1.117 1.219 1.037 1.016
H-Back Porch 1.907 2.222 3.232 2.702 3.910 2.235 2.296 2.201
H-Active 25.422 17.778 16.162 14.222 14.524 13.003 11.852 10.836
(µsec)
Vertical
Ver. Freq. (Hz) 59.940 85.008 75.000 85.061 74.550 75.029 60.020 84.997
V-Total 525 509 625 631 667 800 1066 808
V-Blanking 45 29 25 31 43 32 42 40
V-Front Porch 10 1 1 1 1 1 1 1
V-Sync. 2 3 3 3 3 3 3 3
V-Back Porch 33 25 21 27 39 28 38 36
V-Active 480 480 600 600 624 768 1024 768
(lines)

Sync.

INT(G) NO NO NO NO NO NO NO NO
EXT (H/V)/POLARITY YES -/- YES -/- YES +/+ YES +/+ YES -/- YES +/+ YES +/+ YES +/+
EXT (CS)/POLARITY NO NO NO NO NO NO NO NO
INT/NON INT NON INT NON INT NON INT NON INT NON INT NON INT NON INT NON INT

—2—
 CPD-200ES

TABLE OF CONTENTS

Section Title Page

1. GENERAL ................................................................................... 4

2. DISASSEMBLY
2-1. Cabinet Removal ............................................................7
2-2. Service Position ...............................................................7
2-3. D Board Removal ............................................................7
2-4. Picture Tube Removal ................................................... 8

3. SAFETY RELATED ADJUSTMENT................................. 9

4. ADJUSTMENTS ........................................................................ 10

5. DIAGRAMS
5-1. Block Diagram ................................................................15
5-2. Circuit Boards Location ................................................. 18
5-3. Schematic Diagrams and Printed Wiring Boards ...... 18
1. D Board - Schematic Diagram ................................. 19
2. A Board - Schematic Diagram ................................. 23
5-4. Semiconductors ..............................................................27

6. EXPLODED VIEWS
6-1. Chassis ............................................................................ 29
6-2. Packing Materials .......................................................... 30

7. ELECTRICAL PARTS LIST ................................................ 31

—3—
 SECTION 1

CPD-200ES
The operating instructions mentioned here are partial abstracts from the Operating Instruction
Manual. The page numbers of the Operating Instruction Manual remain as in the manual.
GENERAL

Getting Started Using Your Monitor Adjustments

Before using this monitor, please make sure that the following When one of the preset-type signals is input, no picture p Before adjusting the items, turn on the unit and feed the
items are included in your package: Multiscan 100ES/200ES Preset and User Modes adjustment is necessary.
You can, however, adjust the picture to your preferences by
video signal from the connected computer/work station.
monitor (1), power cord (1), warranty card (1), "Windows95 p Adjustments will be stored automatically.
following the procedure described below.
Monitor Information Disk" (1), and this operating instruction You can adjust all items on the OSD (On Screen Display).
The Multiscan 100ES/200ES has factory preset modes for the 8 most
manual (1).
popular industry standards for true “plug and play” capability.
This monitor will sync with any IBM or compatible system Control Panel
For less common modes, the Multiscan 100ES/200ES’s Digital
equipped with VGA or greater graphics capability. Although
Multiscan Technology will perform all of the complex adjustments
this monitor will sync to other platforms running at horizontal
necessary to ensure a high quality picture for any timing between
frequencies between 30 and 70 kHz, including Macintosh and
30 and 70␣ kHz. RESET COLOR GEOM SIZE CENTER
Power Macintosh system, a cable adapter is required. Please
consult your dealer for advice on which adapter is suitable for CPD-100ES/100EST and CPD-200ES/200EST
your needs. No. Resolution Horizontal Vertical Graphics
(dots × lines) Frequency Frequency Mode
Step 1: With the computer switched off, attach the video
signal cable to the video output. 1 640 × 480 31.5 kHz 60 Hz VGA Graphic 1) Adjusting the Picture Contrast Adjusting the Picture Centering
2 640 × 480 43.3 kHz 85 Hz VESA 2)
3 800 × 600 46.9 kHz 75 Hz VESA 2) The adjustment data becomes the common setting for all input The adjustment data becomes the individual setting for each
signals. input signal received.
4 800 × 600 53.7 kHz 85 Hz VESA2)
5 832 × 624 49.7 kHz 75 Hz Macintosh 1 Press the > ?// button. 1 Press the CENTER button.
16" Color 2) The “BRIGHTNESS/CONTRAST” OSD appears. The “CENTER” OSD appears.
IBM or compatible
computer
6 1024 × 768 60.0 kHz 75 Hz VESA 2)
CENTER
to video output 7 1024 × 768 68.7 kHz 85 Hz VESA 2) BRIGHTNESS/CONTRAST CENTER
8 1280 × 1024 64.0 kHz 60 Hz VESA 2)
100 50 32 68
For the customers using the Windows®4)95
Install the new model information of the Sony computer display 3 1 . 5 kHz/70Hz
—4—

Apple computer
to video output
from “Windows95 Monitor Information Disk” into your PC. (To
install the file, refer to the attached “About the Windows95 Monitor
2 For vertical adjustment
Horizontal Vertical Press the ¨ >/. buttons.
Information Disk/File”.)
frequency∗ frequency∗
Macintosh adapter (not supplied) This monitor complies with “VESA DDC”, the standards of
Plug&Play. If your PC/graphic board complies with DDC,
2 Press the > ?// buttons to adjust picture contrast.
Step 2: Attach the power cord to the monitor and the other / . . . for more contrast
end to a power outlet. select “Plug and Play Monitor (VESA DDC)” or this ? . . . for less contrast
monitor’s model name (CPD-100ES/100EST or CPD-200ES/
200EST) as “Monitor type” from “Control Panel” on The “BRIGHTNESS/CONTRAST” OSD disappears 3 seconds
Windows95. Some PC/graphic boards do not comply with after you release the buttons. > . . . to move up
DDC. Even if they comply with DDC, they may have some . . . . to move down
problems on connecting to this monitor. In this case, select To reset, press the RESET button while the OSD is on.
Power cord (supplied) this monitor’s model name (CPD-100ES/100EST or CPD- For horizontal adjustment
200ES/200EST) as “Monitor type” on Windows95. Press the > ?// buttons.
to a power outlet Adjusting the Picture Brightness
Recommended horizontal timing conditions
Horizontal sync width should be: >1.0 µsec.
The adjustment data becomes the common setting for all input
Horizontal blanking width should be: >3.6 µsec. (Multiscan 100ES)/
Step 3: Turn on the monitor and computer. signals.
>3.0 µsec. (Multiscan 200ES).
Step 4: Vertical sync width should be: < 560 µsec.
If necessary, adjust the user controls according to
your personal preference.
1 Press the ¨ >/. button.
Note The “BRIGHTNESS/CONTRAST” OSD appears. ? . . . to move left
The installation of your Multiscan 100ES/200ES is complete. CPD-100ES/100EST and CPD-200ES/200EST does not apply to / . . . to move right
Enjoy your monitor. Macintosh 21" color mode. BRIGHTNESS/CONTRAST
To erase the “CENTER” OSD, press the CENTER button
1) VGA is a trademark of IBM Corporation. again.
2) VESA is a trademark of the non-profit organization, Video 100 50 The “CENTER” OSD automatically disappears 10 seconds after
Electronics Standard Association. you release the buttons.
3) Macintosh is a trademark of Apple Computer Inc. 3 1 . 5 kHz/70Hz
4) Windows® is a registered trademark of Microsoft To reset, press the RESET button while the OSD is on.
Corporation in the United States and other countries.
Horizontal Vertical
frequency∗ frequency∗

2 Press the ¨ >/. buttons to adjust picture brightness.

. . . . for less brightness
> . . . for more brightness
∗ The horizontal and vertical frequencies for each input signal
The “BRIGHTNESS/CONTRAST” OSD disappears 3 seconds received appear on the “BRIGHTNESS/CONTRAST” OSD.
after you release the buttons.

To reset, press the RESET button while the OSD is on.

4 5
 Adjustments

2 Press the ¨ >/. buttons.

Adjusting the Picture Size > . . .to rotate clockwise Setting the Color Temperature Resetting the Adjustment
. . . . to rotate counterclockwise Data to Factory-preset Levels
The adjustment data becomes the individual setting for each The selected color temperature becomes the common setting
input signal received. for all input signals. To reset an adjustment item
1 Press the SIZE button. 1 Press the COLOR button. Press the button of the adjustment item you want to reset,
The “SIZE” OSD appears. The “COLOR TEMPERATURE” OSD appears. and then press the RESET button before the OSD (On
SIZE COLOR
Screen Display) disappears.
SIZE To erase the “GEOMETRY” OSD, press the GEOM button COLOR TEMPERATURE
again. VAR I ABLE
The “GEOMETRY” OSD automatically disappears 10 5000K 9300K
32 68 50 To reset all adjustment data at once (for
seconds after you release the buttons.
the received signal)
2 For vertical adjustment To reset, press the RESET button while the OSD is on. 2 Adjust with the > ?// and ¨ >/. buttons. Press the RESET button when no OSD is shown.
Press the ¨ >/. buttons. RESET
To select 5000K or 9300K
Adjusting the Pincushion Press the > ?// buttons.
The selected color temperature is indicated in yellow.
The adjustment data becomes the individual setting for each
input signal received.
To reset all adjustment data to factory-
> . . . to enlarge 1 Press the GEOM button. preset levels
. . . . to diminish The “GEOMETRY” OSD appears. Press and hold the RESET button for more than 2 seconds.
GEOM All adjustment data are reset to factory-preset levels.
For horizontal adjustment ? . . . to select 5000K
GEOMETRY
Press the > ?// buttons. / . . . to select 9300K RESET

32 68 To obtain the desired color temperature between

—5—

5000K and 9300K

2 Press the > ?// buttons. Press the ¨ >/. buttons.

? . . . to diminish
/ . . . to enlarge

To erase the “SIZE” OSD, press the SIZE button again.

The “SIZE” OSD automatically disappears 10 seconds after ? . . . to diminish the picture sides
> . . . for higher temperature
you release the buttons. . . . . for lower temperature

To reset, press the RESET button while the OSD is on. Your most recent adjusted color temperature will be
recalled by pressing the ¨ >/. button.
/ . . . to expand the picture sides
Adjusting the Picture Rotation
To erase the “COLOR TEMPERATURE” OSD, press the
COLOR button again.
The adjustment data becomes the common setting for all The “COLOR TEMPERATURE” OSD automatically
input signals. disappears 10 seconds after you release the buttons.
To erase the “GEOMETRY” OSD, press the GEOM button
1 Press the GEOM button.
again. To reset, press the RESET button while the OSD is on.
The “GEOMETRY” OSD appears.
The “GEOMETRY” OSD automatically disappears 10
GEOM seconds after you release the buttons.
GEOMETRY
To reset, press the RESET button while the OSD is on.
32 68

CPD-200ES
6 7
 CPD-200ES
Entering New Timings Plug and Play Troubleshooting
When using a video mode that is not one of the factory This monitor complies with DDCTM1 and DDC2B, which are This section may help you isolate a problem and as a result, Screen image is not centered or sized properly
preset modes, some fine tuning may be required to optimize the Display Data Channel (DDC) standards of VESA. eliminate the need to contact technical support, allowing / Adjust the “CENTER,” “SIZE,” or “GEOMETRY”
the display to your preferences. Simply adjust the monitor When a DDC1 host system is connected, the monitor continued productivity. on the OSD (pages 5, 6).
/ Some video modes do not fill the screen to the
according to the preceding adjustment instructions. The synchronizes with the V. CLK in accordance with the VESA No picture edge of the monitor. There is no single answer to
adjustments will be stored automatically and recalled standards and outputs the EDID (Extended Display / If the u POWER indicator is not lit. solve the problem. There is a tendency to have
whenever that mode is used. Identification Data) to the data line. — Check that the power cord is properly this problem on higher refresh timings and
A total of 8 user-defined modes can be stored in memory. When a DDC2B host system is connected, the monitor connected. Macintosh video timings.
If the 9th mode is entered, it will replace the first. automatically switches to the DDC2B communication. — Check that the u POWER switch is in the
“ON” position. Picture is fuzzy
DDCTM is a trademark of the Video Electronics Standard / If the u POWER indicator is flashing in green / Adjust the “CONTRAST” and “BRIGHTNESS”
Association. and orange alternately. on the OSD (page 5). We have come across
— Check that your computer power switch is in
Power Saving Function the “ON” position.
— The monitor will recover when you press any
several brands of SVGA boards that have an
excessive video output level which creates a
fuzzy picture at max contrast.
key on the keyboard of the computer. / Trip the u POWER switch once to activate the
This monitor meets the power saving guidelines set by the
International ENERGY STAR Program as well as the more
Use of the Tilt-Swivel — Check that the video cable is properly
connected.
Auto-degauss cycle∗.

— Ensure that no pins are bent or pushed in the Picture bounces or has wavy oscillations
stringent TCO92 803299 (NUTEK) guidelines. It is capable HD15 connector of the cable. / Isolate and eliminate any potential sources of
of reduced power consumption when used with a computer With the tilt-swivel, this unit can be adjusted to be viewed at — Check that the video card is seated electric or magnetic fields. Common causes for
equipped with Display Power Management Signaling your desired angle within 180˚ horizontally and 20˚ vertically. completely in a proper bus slot. this symptom are electric fans, fluorescent
(DPMS). By sensing the absence of the sync signal coming To turn the unit vertically and horizontally, hold it at its — Check that the video sync signal is within lighting, laser printers, and so on.
from the computer, it will reduce the power consumption as bottom with both hands. that specified for the monitor. / If you have another monitor close to this
follows: — If using a Macintosh system, check that a monitor, increase the distance between them to
proper HD15 - D15 adapter is provided to reduce the interference.
CAUTION: The Power Saving function will automatically 15° work correctly with your Macintosh. / Try plugging the monitor into a different AC
put the monitor into Active-off state if the power — The monitor has a self-diagnose function. outlet, preferably on a different circuit.
90° After disconnecting the video signal cable
switch is turned on without any video signal / Try the monitor on a completely different
from the computer, turn on the u POWER computer in a different room.
input. Once the horizontal and vertical syncs are
—6—

switch of the monitor. Press and hold the "+"

sensed, the monitor will automatically return to side of the > button for 2 seconds, then color
90° Picture appears to be ghosting
its Normal operation state. bars will appear. The monitor is operating / Eliminate the use of video cable extension cables
5° normally if the red, green, and blue color bars and/or video switch boxes if this symptom
Required appear. Contact the maker of the computer to occurs. Excessive cable length or weak
Power u POWER which the monitor is connected.
State resumption connections can produce this symptom.
consumption indicator / If the u POWER indicator is flashing.
time
— There is a potential monitor failure. Contact A fine horizontal line (wire) is visible
Normal
1 110 W –– green on your dealer. / This wire stabilizes the vertically striped
operation
Aperture Grille (page 8). This Aperture Grille
Stand-by Orange and If the message of “OUT OF SCAN RANGE” appears on the allows more light to pass through to the screen
approx. green flashes screen
2 (1st step of 15 W giving the Trinitron CRT more color and
3 sec. alternately / Check that the video sync signal is specified for
power saving) brightness.

3
Suspend
(2nd step of 15 W approx.
3 sec.
Orange and
green flashes
Damper Wire the monitor.

Picture is scrambled
Wavy or elliptical (moire) pattern is visible
power saving) alternately / Due to the relationship between resolution,
/ Check your graphics board manual for the monitor AG pitch and the pitch of some image
Active-off Using a white background, very thin horizontal stripes on proper monitor setting on your Multiscan 100ES/ patterns, certain screen backgrounds, especially
(3rd step of 8W approx. Orange on 200ES.
4 10 sec. the screen are visible as shown on the illustration. These gray, sometimes show moire. This can only be
power saving) stripes are damper wires. These wires are attached to the / Check this manual and confirm that the graphic eliminated by changing your desktop pattern.
5 Power-off 0W –– off mode and the frequency at which you are trying
aperture grille inside the Trinitron tube and are there to
to operate is supported. Even within the proper Just after turning the monitor on, a “boon” noise is heard
dampen vibrations of the aperture grille in order to prevent
range some video boards may have a sync pulse / Just after turning the monitor on, a noise may be
them from influencing the picture quality. that is too narrow for the monitor to sync heard for about 3 seconds.
Damper wire correctly. This noise is not failure, it is caused by the Auto-
degauss cycle∗.
Approx. 6 cm Color is not uniform
(CPD-200ES/ / If the monitor is close to any potential sources of ∗ The Auto-degauss function demagnetizes the metal frame of
200EST only) magnetic fields such as a speaker, or you turn the the CRT to obtain a neutral field for uniform color
monitor while the u POWER switch is in the reproduction. If a second degauss cycle is needed, allow a
“ON” position, color may not be uniform. Trip minimum interval of 20 minutes for the best result.
the u POWER switch once to activate the Auto-
degauss cycle*. • If the problem persists, call your authorized Sony dealer from
a location near your monitor.
Picture is flickering
Approx. 6 cm
• Note the model name and the serial number of your monitor.
/ If the refresh rate is not appropriate, the picture
Also note the make and name of your computer and video
may flicker. Set the refresh rate of the
board.
non-interlace mode as high as possible on the
computer. For detailes on how to set the refresh
rate, consult the dealer of your computer or
video board.
8 10
 CPD-200ES
SECTION 2
DISASSEMBLY

2-1. CABINET REMOVAL 2-2. SERVICE POSITION

2 Cabinet

A board

D board
2
1 Four screws
(BVTP 4 x 16)

2-3. D BOARD REMOVAL

1 A board 6 Five screws

(BVTP 3 x 12)
2 One screw
(BVTT 4 x 8)

3 Cable stopper

4 Two screws
(BVTP 3 x 12)

5 Cable bracket

7 D board

—7—
CPD-200ES 8 Demagnetization coil

2-4. PICTURE TUBE REMOVAL

9 Two screws
7 Tension spring (BVTP 4 x 16)

6 A board

5 Neck assy

4 Deflection yoke

3 Four screws
(Tapping screw 5)

10 Stand assy
2 Picture tube shield (D board)

1 Anode cap

Cushion

• REMOVAL OF THE ANODE-CAP

NOTE: Short circuit the anode of the picture tube and the anode cap to the metal chassis, CRT shield or carbon painted on the CRT, after
removing the anode.

• REMOVAL PROCEDURES

Turn up one side of the rubber cap in Use your thumb to pull the rubber cap When one side of the rubber cap sepa-
the direction indicated by arrow . firmly in the direction indicated by rates from the anode button, the anode-
arrow . cap can be removed by turning the rub-
ber cap and pulling it in the direction of
arrow .
• HOW TO HANDLE AN ANODE-CAP
Do not use sharp objects which may cause damage to the surface
of the anode-cap.
Do not squeeze the rubber covering too hard to avoid damaging
the anode-cap. A material fitting called a shatter-hook terminal is
built into the rubber.
Do not force turn the foot of the rubber cover. This may cause the
shatter-hook terminal to protrude and damage the rubber.

—8—
 CPD-200ES

SECTION 3
SAFETY RELATED ADJUSTMENT

When replacing parts shown in the table below, the b) HV Hold-Down Check
following operational checks must be performed as a 1) Using an external DC Power supply, apply the
safety precaution against X-rays emissions from the unit. voltage shown below between cathode of D511
on "D" Board and GND, and confirm that the
HV Hold-Down circuit works. (Raster disappears)
D - BOARD Standard voltage: 35.00 + 0.00 VDC
Part Replaced ([) - 0.10
RV501
Check Condition
Part Replaced (]) • Input voltage : 120 + 2 VAC
• Input signal : Any pattern (fH = 64 kHz)
IC801, IC901, IC904, FBT T501, D511, D515, D596, • Controls : CONT 2 Maximum
R532, R533, R534, R535, R538, R539, R540, R541, : BRT 2 Center
R542, R543, R544, R545, R807, R822, R823, R824,
R939, R996, RV501, C509, C515, C516, C517, C519,
C531, C542, C548, C549, C802, C814, C815, C904,
C910, R598, R599
c) Beam Protector Check
1) Using an external DC power supply, apply the
Allow the unit to warm up for one minute prior to voltage 7.00 + 0.05 VDC between pin 11 of FBT
checking the following conditions: (T501) and GND, and confirm that the voltage
of both ends C519 is with in the voltage range
shown below.
a) HV Regulator Check Standard voltage: Less than 3.26 VDC
1) Input white cross hatch signal. (fH = 64 kHz)
2) Set [Link] data to minimum. Check Condition
3) Cut off Screen VR (G2). • Input voltage : 120 + 2 VAC
4) Input voltage: 120 + 2 VAC • Input signal : Any pattern (fH = 64 kHz)
5) Confirm that the voltage is within the voltage range • Controls : CONT 2 Maximum
shown below: : BRT 2 Center
Standard voltage: 25.0KV + 0.2KV
6) When replacing components identified by ], make
sure to recheck the High Voltage.
7) Verify the High Voltage as shown above (25.0KV + 0.2KV) d) +B MAX. Check
is within specification. If not, set H. SIZE data at 1) Input white cross hatch (fH = 64 kHz) signal.
minimum (-127) and then adjust RV501 on "D" Board. 2) Set CONT and BRT to Maximum
8) After adjusting the High Voltage within specification, 3) Input voltage: 120 + 2 VAC
put the RV cover on RV501 as shown below and apply Note: Use NF power supply or make sure that
sufficient amount of RTV around RV501. distortion factor is 3% or less.
4) Confirm that the voltage is within the voltage
range shown below.
Standard voltage: 151.0 + 4.25 VDC
Measurement Point: CN505 Pin 1 and GND

4
10

RV501

—9—
CPD-200ES

SECTION 4
ADJUSTMENTS

Connect the communication cable of the connector located on the D board on the monitor. Run the service software and
then follow the instructions.

1 1-690-391-21 2 A-1500-819-A 3 3-702-691-01

Interface Unit Connector Attachment

IBM AT Computer To BUS CONNECTOR

as a Jig

D-sub mini Din 4 Pin 4 Pin 4 Pin

(9 Pin [female]) (8Pin)

*The parts above ( 1 ~ 3 ) are necessary for DAS adjustment.

Allow a 30 minute warm-up period prior to making the following adjustments.

Landing Rough Adjustment Convergence Fine Adjustment

1. Enter the full white signal. Set DY four-pole magnet to mechanical center
2. Adjust the contrast to the maximum. before adjustment.
Mechanical
3. Make the screen monogreen. This should be prime mode. Set the
finger Center

4. Reverse the DY, and adjust coarsely the purity magnet so

that a green raster positions in the center of screen.
5. Moving the DY forward, adjust so that an entire screen NECK Assy
(Stable)
becomes monogreen. P.S Mg
6-pole Mg
6. Adjust the tilt of DY, and fix lightly with a clamp.

DY CRT
Landing Fine Adjustment
1. Place the set in the Helmholtz coil.
2. Enter a green signal only.
4-pole Mg P.S Mg
3. Degauss the entire screen with hand-degausser.
Then auto degauss it.
4. Attach a wobbling coil to the specified position of CRT 1. Receive R.B. crosshatch.
neck. 2. Adjust H. STAT and V. STAT at four-pole magnet.
5. Attach a landing adjuster sensor on the CRT.
6. Using a landing checker, adjust the DY position, purity on < 4 Pole Magnet>
DY, tilt of DY.
7. Clamp the DY screw. 2
R
1 1 + 2
B
Clamping torque: 22 + 2 kgcm (2.2+ 0.2 Nm) 1 R
R
2 B
B
Convergence Rough Adjustment
1. Enter the white crosshatch signal. 2 1 R 1 + 2
B
2. Adjust roughly the horizontal and vertical R
B
convergence at four-pole magnet. 1
2
RB
3. Adjust roughly HMC and VMC at six-pole
magnet.

— 10 —
 CPD-200ES
3. Receive White cross-hatch. Zero Position NECK Asssembly
4. Adjust HMC and VMC at six-pole magnet.
Purity Purity 4-Pole Mg 6-Pole Mg

< 6 Pole Magnet> on DY on NA

2

1 G

G
Purity Magnet
1
(Keep zero position at all times)
6-Poles Magnet
(HMC/VMC
Corrector)
5. Display R and B cross hatch patterns.

6. Adjust H STAT and V STAT with 4-pole magnet.

6-Poles Magnet
([Link]/[Link]
7. Display white cross hatch patterns. Corrector) Purity Magnet

8. Adjust HMC and VMC with 6-pole magnet.

9. Display R and B cross hatch patterns.

Vertical and Horizontal Position and Size
10. Adjust XCV and XCV roller. Specification
a
11. Adjust XBV and XBV reactor. a < 2.5mm
b < 2.5mm

12. Adjust [Link] with 4-pole magnet. a

A B
A
Repeat steps 7 to 12 above and make R, G, B of both vertical and 234mm 312mm
horizontal lines to be overlaid at the center of the x-axis.
B
13. Adjust [Link] with TLH Corrector.
b b
14. Adjust XCV with XCV core.
Convergence Specification
B
XCV movement
R
B A 0.24mm
0.24mm
B 0.28mm
0.30mm
15. Adjust [Link] with TLV VR. A
B
R
R
B
B
R
TLV movement R
B

16. Adjust [Link] with YCH VR.

Focus Adjustment
Adjust focus (V) and focus (H) for optimum focus.
YCH movement R B

R B
17. Adjust YBH with YBH VR.
R

YBH Movement

FOCUS (V)

18. Paint lock the four-pole magnet ,six-pole magnet, XBV

reactor, XCV corrector and TLH corrector handle.
FOCUS (H)
TLH Corrector (insert to only one side)

<VR Adjustment on DY>

TLV
YCH YBH
XCV
XBV

— 11 —
 CPD-200ES

5-2. CIRCUIT BOARDS LOCATION

5-3. SCHEMATIC DIAGRAMS AND PRINTED WIRING BOARDS

Note:
• All capacitors are in µF unless otherwise noted. pF: µµF • When replacing parts shown in the table below,
50 WV or less are not indicated except for electrolytic. be sure to perform the safety related adjustment.
• Indication of resistance, which does not have one for rating
electrical power, is as follows.
D - BOARD
Pitch: 5 mm
Rating electrical power 1/4 W (CHIP: 1/10 W)
Part Replaced ([)
RV501
• All resistors are in ohms.
• f : nonflammable resistor. Part Replaced (])
• F : fusible resistor.
• ∆ : internal component. IC801, IC901, IC904, FBT T501,
• p : panel designation and adjustment for repair. D511, D515, D596, R532, R533,
• All variable and adjustable resistors have characteristic curve B, R534, R535, R538, R539, R540,
unless otherwise noted. R541, R542, R543, R544, R545,
• e : earth-ground. R807, R822, R823, R824, R939,
• E : earth-chassis. R996, RV501, C509, C515, C516,
• The components identified by [ in this basic schematic C517, C519, C542, C548, C549,
diagram have been carefully factory-selected for each set C802, C814, C815, C904, C910,
in order to satisfy regulations regarding X-ray radiation. R598, R599, C531
Should replacement be required, replace only with the
value originally used.
• When replacing components identified by ], make the necessary • All voltages are in Volts.
adjustments by using RV501 ([) as indicated. (See page 9) • Readings are taken with a 10 ΜΩ digital multimeter
• Readings are taken with a color-bar signal input.
• Voltage variations may be noted due to normal
Note: The components identified by shading and production tolerances.
mark ¡ are critical for safety. Replace only • * : Can not be measured.
with part number specified. • Circled numbers are waveform references.
• : B +bus.
• : B - bus.
Les composants identifies per un trame et une marque
¡ sont critiques pour la securite. Ne les remplacer
que par une piece portant le numero specifie.

— 18—
— 15 —
 CN305
10P
WHT
CN307
9P 10 GND
WHT
RGB PRE-AMP +12V 9 +12V
IC001
BGND 1 8 GND
11
BLUE 2 BIN 23 +5V 7 +5V
R-OUT J001
GGND 3 CRT DRIVER 6 H2
8 20
GREEN 4 GIN G-OUT IC002 5 H1
4
SIGNAL IN RGND 5 18 8 VIN3 VOUT3 5 4 GND
H2
5 B-OUT 7
RED 6 RIN KR +80V 3 +80V
9 VIN2 VOUT2 3 8
GND 7 KG 2 NC
9
VD 8 11 VIN1 VOUT1 1 KB +150V 1 +150V
1,2,3 19,20,21
CONNECTOR SYNC ON GRN R,G,B
HD 9 R,G,B
15PIN D-SUB STRIPPER OSD
Q002,Q003,Q006 16 27 1 G2
BUFF BLK G-DRV PWM0
CN309 26 2 10
Q004,005 15
CLP B-DRV PWM1
8P
25 11
BRT PWM2
CSYNC 8 13 12
CONT PWM3 OSD
GND 7 H PICTURE TUBE
IC003 CUTOFF AMP
HSOUT 6 4 IC004
14 1
V-SYNC
VSOUT 5 PWM5 9
5
GND 4 H-SYNC 23
PWM6
CBLK 3 15
SCL 24
BPCLP 2 PWM7
2 CN302 HV
16
GND 1 SDA 8 1P (TO FBT)

CN306 17 1 GND
7P RESET

VRTRC 7
PWM4
HRTRC 6 3 CN301
13 7 1P
GND 5 5
+12V 1 1.2K
12CSCL 4

12CSDA 3 G2-CUT OFF

CONTROL CN303
BND 2
SPOT KILLER IC005 1P
RESET 1
Q001
1 GND
CN310
4P
CPUGND 4
CN308
DDCSDA 3 1P

DDCSCL 2 1 GND

+5VS 1

CN311
4P
+5VS 1

DDCSCL 2

DDCSDA 3
(VIDEO)
CPUGND 4

CN510
1P
POWER
( DEFLECTION ) HST
T505 1 1.2 KV

5 1

CN511 CN512
8P 1P
WHT
3
3 2 1 GND
GND 1 FLYBACK

BPCLAMP 2 30 1 5
22 [Link] +IN V-OUT OUT
CBLANK 3 SBLKOUT IC401
GND 4 32 7
[Link]/OUT -IN
VSYNC 5
PWM-CONT
35
IC801 FBT
8,9 [Link]
HSYNC 6 H-SYNC 1 22 21 T501

GND 7 6 COMPARATOR
5,6 JUNGLE BUFF ERROR SW-REG
SYNCONGRN 8 SYNC ON GRN 19 2 HV
AMP
Q503 TO CRT
IC904 5 SAW TOOTH
GEN
C-BLANK 14
27 22
IC902 SAW TOOTH
FUNCTION
18,19 GEN RV501
SWITCH SW DATA1,2 V-SYNC BPCLAMP [Link] OUT
16 1
Q510 13

21
[Link] 12 13
CN508 CPU FOCUS
15
11P 31 1 HDT
BUFF
WHT IC901 SYNC ON GRN SYNC-SW T504
INV 50
5V SENSE 1 DDC 5V DET. 1 17
Q902
51 29 13
DDCSCL 2 DDC CLK H-SYNC H-SYNC OUT
} 8 CN501
DDCSDA 3
} 52
DDC DATA
16
6P
26 34 DY
CPU GND 4 V-DRIVE V-SYNC 6 [Link]
25 Q507 1 H DY+
RESET 5 RESET 30 17 [Link] [Link] OUT 4 11 ABL
H-DRIVE H-SYNC 2 H DY+
GND 6 RESET Q504,505 Q502
6
IC903 53 3 H DY-
IICDATA 7 DATA 39
}
IICCLK 8
} 54
CLK
REMOTE ON/OFF
1 5
4 H DY-

[Link] 5 V DY-
GND 9 [Link] VCC
49 35 6 V DY+
HRTRC 10 HRTRC [Link] VCC CONTROL 4
20
VRTRC 11 15 Q528,529
VRTRC 8
ABL
34
CN509 ROTATION
4P 13 47 12 9
RX [Link]
WHT
42 40
TX HTR STDBY
DGND 1 CN505
33
10P
+5V 2 +5V OSC IN
WHT
RXD 3 X900
SRT
32 8MHz 1 150V
TXD 4 DEGUASS S0-S2 OSC OUT T601
2 NC
21 44,
45, 3 80V
9 10
46 4 GND
TO S-CAP 150V
CHANGE
RELAY 3 5 H1
DRIVE 11
+12V 80V +5V 6 H2
DISABLE 7
Q670
16V 5V,12V REG OUT 7 5V
CN601 SW-REG CONT 12 1,2
IN1,2 +12V 8 GND
3P 1 IC601 SW-REG IC604
Vcc 5 6
3
5 OUT OUT OUT 9 12V
DGC1 3 FLDBK 13
Q602 10 GND
DGC NC 2 EA CIS 3

DGC2 1 13 7 14

LFT DFT
CN600 15 T503
LF601 2 -10V
12

AC-RECT 16 HEATER SW BUFF

AC IN BUFF DF-AMP 1 11 AMP
D601
Q654,655 Q508,509 Q515
1 Q500 10
Q501
17

IC603 9
CN605 5
2P
5 1 8
S-CAP CHANGE
7 S0-S2
THP601 2
4 2 3 ERROR AMP 1 STBY.
CONTROL
THP601A 1 IC652 Q656
CN503
2P
ROTATION
DRIVE 1 ROT+
IC400
2 ROT-

B-#SV3449<MANUAL/CH>-BLK..
 5

11 12
G3 J001
10
IC002
VIDEO LM2405T 9 C035 RCV 1 1
8 10 13
RGB OUTPUT 10000p

VBIAS

VOUT3

GOUT2

VOUT1
2kV SG001 G1
3 SG003

VIN1

VIN2

VIN3

GND3

GND2

GND1
F :LEAD :LEAD

VCC
9 G2 H2
11 4
D307
RD18ESB2
11 10 9 8 7 6 5 4 3 2 1 R064
G2 10 5
12V 10k H
8 9 6 3
1/2W
+12V
FB203 :RC KB 8 7 KR
FB013 CN301
:CHIP R115 R215 R315 11 7 KG KR 4 1P
FB303 FB103 47 47 47
:CHIP :CHIP :FPRD :FPRD :FPRD 6 5
1 1.2KV
R304 12 13 R048
C334 R104 2.2M
33 FB101 FB201 FB301 CONNECT TO
0.1 47 :CHIP :CHIP :CHIP 1W
:CHIP 25V :CHIP D BOARD
IC001
B:CHIP CN510
MM1382 FB3
RGB PRE-AMP L
IC003 R204 C011
R162 C103 R103 68 D104
C202 SNY425 D204 0.1
1k 0.1 10k :CHIP C014 SG201 SG101
25V 0.1 R203 OSD HSS82 HSS82 100V SG301
:CHIP :RN-CP 47 +80V :LEAD :LEAD
B:CHIP 25V 100k PROT PROT :PT :LEAD

28
100V

1
ROI RDRV C203 B:CHIP :CHIP
R262 R2 0.1

24
1k

1
2.7k 25V PWM0 PWM7
:CHIP R303 L305
:RN-CP B:CHIP D304 C306

27
GOI GDRV 100k

2
C303 C302 HSS82 0.1
R362 :CHIP
0.1 0.1 PROT 250V R305

23
1k

2
25V 25V PWM1 PWM6 C031
R19 :MPS 330
:CHIP

+12V
B:CHIP B:CHIP :CHIP 1000p

26
BOI BDRV 100

3
500V
C027 R39 :CHIP R351
D105 B

22
3
1.0 330k FBLK TEST L205 100
16V :RN-CP R14 HSS82 1/2W
C206

25
4
VOS BRT 100 PROT :RC
1 :CHIP 0.1
250V R205

21
4
VSYNC B
R6 :MPS 330
:CHIP

24
RIN CLP1 100

5
C006 C104 :CHIP R251

20
220 R111 HSYNC G D205

5
2 0.47 C005 L105 100
D302 390
16V 16V HSS82 1/2W
1SS119 C037 330p C106

23
VCC ROUT

6
D301 R114 100 CH PROT 0.1 :RC
PROT C008
1SS119 3.3k 16V 250V R105

19
BGND 0.1

6
1 :CHIP VDD R :MPS 330
PROT 25V C022
1 :CHIP

22
BLUE

7
2 B:CHIP GND VCC
R301 R302 D201 3 C109 16V CN399
C301 R151
FB302 C013 C012 220p F D106 P1

18
GGND 3 75 47 1SS119 PIXCLP GND D305

7
:LEAD 1.0 CH:CHIP 100
:CHIP :CHIP 220 0.1 HSS82 1/2W

+12V
PROT 16V 25V R028 C092 HSS82 TO BRKT CABLE

21
GREEN 4 GIN GND PROT

8
1.8 0.1 R309 :RC
PROT
R201 C201 R202 2W 25V 1M
FB202 4 D206

17
RGND 5 75 CKOUT RESET

8
:LEAD 1.0 47 :RS B:CHIP :CHIP
:CHIP :CHIP HSS82
C055

20
RED

9
6 VCC GOUT 15p CH:CHIP PROT R209
R101 D202 D101 C204 R214 7 1M
FB102 75 C101 R102 0.47 D306

16
GND

9
7 :LEAD 1.0 1SS119 1SS119 47 R211 3.3k XTA_O SDA IC004 :CHIP
:CHIP 16V 390 :CHIP X1 R24 HSS82
PROT PROT :CHIP 8MHz 4.7k TDA6103Q PROT

10

19
VD 8 D102 GND CLP2
:LEAD :CHIP CUT OFF AMP R109 CN302
1SS119 C009 5 C209 FB110 1M P1

10

15
HD 9 XTA_I SCL

VOC3

VOC2

VOC1
R26 PROT 0.1 25V B:CHIP 220p :CHIP :CHIP

VI1

VI2

VI3

GND

VIP

VCC
10k CH:CHIP C036 R25 TO BRKT CABLE

11

18
:CHIP BIN BOUT 4.7k R106
CN307 FB104 C304 15p CH:CHIP 10k FB210
9P :LEAD :CHIP :CHIP

11

14
6 0.47 PWM2 PWM5 1 2 3 4 5 6 7 8 9
16V R314 R12 R27
SIGNAL IN 12 FB310

17
REF CLP3 R311 3.3k 330k 150k
:CHIP
R16 R10 C010 390 :CHIP :CHIP :RN-CP
R22 R206

12

13
10k 1k 1k 0.1 25V B:CHIP PWM3 PWM4
C309 10k
:CHIP :CHIP :CHIP R3
220p
13

16
CONT BLK 150k R33 IC005
R13 CH:CHIP 12V R40
C004 :CHIP 15k M5218AP
Q005 10k 1M CN303
0.1 :CHIP
2SA1037K :RN-CP R29 :CHIP CUT-OFF CTRL P1
25V C015 R306 150k

+5V
14

15
BUFF B:CHIP OC CLP 0.1 10k :CHIP TO BRKT CABLE
25V R32 C330 C351

4
B:CHIP 3.9k 4.7 0.1
:CHIP 250V D014
C029

3
C020 :MPS 1SS119
10p C019 0.47

+150V

+80V
R15 5V R107 PROT

+12V
R053

2
CH:CHIP 0.1 16V
1.5k 10k 22M
:CHIP 25V R110 R210 R310
:RN

1
B:CHIP 220k 220k 220k
R57 L101 1/8W 1/8W 1/8W
2.2k 5V 4.7mmH R207 :CHIP:CHIP :CHIP C024
:CHIP 10k R45 330p
Q004
+5V +5V 2.2k CH:CHIP
2SC1623-L5 R7 C110 :CHIP
CONNECT TO R4 R5 L201 Q001
BUFF D002 1k 4.7mmH R307 10p
D BOARD 33k 1k 2SC5022 C023
1SS119 :CHIP :CHIP Q003 :CHIP 10k
CN511 FB7 C100 SPOT KILLER 0.001 C108
47 2SA1162-G R49 CH:CHIP 0.1
R58 L L301
CN309 25V C088 R108 R208 R308 C028 220k 25V
470 R31
8P 220 4.7mmH 6.8k 6.8k 6.8k 47 :CHIP B:CHIP CN305
:CHIP 1k
16V :CHIP :CHIP :CHIP 25V 10P
CSYNC 8 Q006 :CHIP
R1 C007 Q002
FB8 1k 47 2SA1162-G 2SA1162-G
GND 7 :CHIP 25V 10 GND
L R30 L001
R77 C105 C305 C107 C307
HSOUT 6 100k 820 C030
9 +12V
0.1 C205 0.1 1 C207 1
R11 :CHIP :CHIP 25V 0.1 25V 16V 1 16V 0.22 FB6
VSOUT 5
R17 56k B:CHIP 25V B:CHIP F 16V F 16V L 8 GND
100 :CHIP B:CHIP F B
GND 4
SYN G-STRIPPER
7 +5V
:CHIP
CBLK 3 +12V FB4 6 H2
L
C016
BPCLP 2 12V 100
C001 5 H1
R18 0.22
16V
GND 1 100 :MPS FB1 4 GND
:CHIP L
FB11 3 +80V
L C002
CN306 +5V 0.1 2 NC
7P 250V
5V 1 +150V
VRTRC 7
C017 FB5
C018
HRTRC 6 100 10 L CONNECT TO
16V C003
C025 C026 200V 0.1 D BOARD
GND 5 FB9 R20 100p 100p
L 100 :CHIP 250V
CH:CHIP CH:CHIP CN505
I2CSCL 4

I2CSDA 3
FB10 R21
GND 2 L 100 :CHIP

RESET 1
C021 R8
CONNECT TO 0.01 100 :CHIP
B
D BOARD
CN508
C041
0.1
25V
B:CHIP
FB12
CPUGND 4
R35 47 :CHIP
DDCSDA 3
R36 47 :CHIP
DDCSCL 2
B-#SV3449<MANUAL/CH>-A..
+5VS 1
RD5.6ESB2

CN310
RD5.6ESB2

4P
D017

PROT
D016

PROT

SIGNAL IN
C040
0.1
25V
B:CHIP
1

4
+5VS

CPUGND
DDCSCL
DDCSDA

CONNECT TO
D BOARD
CN311
4P CN508
 CN509 FOR SERVICE
4P

1 D GND
+5V +5V +5V 2 +5V
R907 1k
3 RXD
R979 R929 R918
5V 33k 4 TXD
18k 39k R900 1k

POWER DEFLECTION
R938 C906 D921 CN508 TO A BOARD
R980
C907 8.2k 0.47
D923 1SS119 11P CN306&CN311
C915 150k :MPS
R944 4.7 5V
R945 R956 R986 4.7
5V
1SS119 R987
3.9k 3.9k 35V 1 5VSENSE
2.2k 10k PROT 4.7k
:RN :BP
2 DDCSCL
R919 R916 R915
4.7k 1k 1k
3 DDCSDA
R908
IC904 4 CPUGND
4.7k R992 1k
TDA9105 R912
JUNGLE IC901 470 5 RESET
D916
[Link]
ST7272N5B1/CUS R901 R902 R903 D915 R904
6
4.7k 4.7k 4.7k 4.7k 1SS119 GND

42
CPU 1SS119 R991 100

1
PROT
PIN/BAL PROT 7 IICDATA
R990 100 FB901

56
HLK/ULK 8 IICCLK

1
VDDA

41
D917 C902

2
VSSA
C901 R993

+5V
R905 KEY BAL IN EWPCC 1SS119 0.0047 9 GND
R942 R940 R924 R930 R925 R926 R927 R928 C962 D918 10k

55
0.1

2
4.7k EWPCC :PT
PLL2C 27k 27k 27k 27k 18k 27k 27k 27k 0.1 :PT VSS
PROT 1SS119 10 HRTRC
:PT

40
PROT

3
HDUTY IIC CLK

54
VRTRC

3
P/K BAL OUT R989 DA0 11
C963 R994 1k
10k PC5
[Link] 0.1
H SIZE IIC DATA R936
:PT

39

53
R933

4
DA1 4.7k
C944 R911
E/W AMP PC4 15k
0.0022 D945 R960 15k
PIN BAL DDC DATA
:PT ISS119 4.7k

52
[Link]

5
DA2 D920

38
R959 8.2k

5
PC3_MOSI MTZJ-4.7C
KEYST KEY BAL DDC CLK
D903 D944

51
6
DA3
HSS82 1SS119 [Link] R943 8.2k
PC2_MISO

37
6
D946 PIN DDC 5VDET

50
R909

7
E/W OUT DA4
ISS119 47k
R972
R931 8.2k PC1_H.SYNCI2
10k
[Link] KEY H RTRC

36

49
7

8
DA5
[Link] R941 8.2k PC0_OCMP_HFBACK D909
V CENT
RD5.6ESB2 Q902

48
FC2

9
DA6 R962 DTC124ESA

35
R932 8.2k

8
VPP_TEST 10k
C940 [Link] V SIZE H CENT D906 INV

10

47
0.047 DA7 RD5.6ESB2
:PT FC1 1 R934 10k DA17

34
C968

9
VLINBAL S2

11

46
[Link] DA8 1.0
R935 8.2k DA16
CO VLIN S1

10

33

12

45
DA9
[Link] R937 DA15
R949 R950 R951 8.2k RX
R964 R968 R948 R947 R952 S0

13

44
RO 150k 150k 150k C927 PB7
150k 150k 150k 150k 150k

11

32
47 DA14
[Link] 25V TEMP

14

43
PB6
PLL1F C912 C913 C917 C918 C919 C904 PA0
C916 C920 C921
2.2 2.2 2.2 0.1 :PT

12

31
2.2 2.2 2.2 2.2 2.2 ABL TX

15

42
[Link] PB5 D913
R975 339VYUGW
R939 PA1
10k LED
R958 [Link] 1k S4

13

30

16

41
5V 1.8k PB4
C943 [Link] PA2
0.022 C925 PLL LOCK HTR STDBY C970
R1801 R1822 C934 C928 C945 Q901

G
:PT 220

17

40
PLL1INHIB PB3 100p 2SC2785
3.3k 3.3k 2.2 0.01 0.022

14

29
16V PA3
:RN :RN :PT :PT 5V B
C536 [Link] SW DATA2 REMOTE ON/OFF SW

18

39
0.022 PB2 R981 R999
C923 C948 100V
C1803 C924 C939 C926 R957 C910 [Link] PA4 470 470

15

28
0.01 0.1
0.22 C1802 0.1 0.047 0.001 6.8k 47
SW DATA1 POWER LED R963

19

38
C1801 :PT :PT :PT :RN :PT [Link] C935 PB1 10k
:MPS 330p :PT 25V R955
330p 0.22 PA5
:B B 240k :MPS
XRAYIN V RTRC5 PWR SAVE LED D924
FB904

16

27

20

37
VFBACK_PBO 1SS119 R973
C941 CN511 TO A BOARD
[Link] PA6 10k
0.22 8P
DEGAUSS CN309
C950 C960 :MPS

21

36
S1803 1.0 1.0 [Link] V.SYNCI2_PD3

17

26
R998 1
R1810 :MPS :MPS 12V PA7_BLANKOUT GND
BRIGHT- [Link] BP CLAMP H DRVVCC 10k
2
470

22

35
:RN CLMPO_PD3 R995
2 BPCLAMP
R1823 VCC DA13
R906 15k 470

18

25
RESET 470 MOIRE ROTATION 3 CBLANK
R1811

23

34
BRIGHT+ :RN [Link] C933 DA10
S1821 L900 R921
330 220 DA12 X900 C903 5V 4 GND
22k FB902
:RN GND 16V [Link] 8MHz 15p :CH
S1801

19

24

24

33
DA11 5 VSYNC
S1809
R1812 R1832 [Link] C931 C932 5V OSCIN
9
470 100k 0.22 0.1 RESET 6 HSYNC
C961

25

32
:RN :RN [Link] :MPS :PT RESET R920
0.1

20

23
OSCOUT R946 C908 14 13 12 11 10 9 8 1.0k 7 GND
R1813 :PT
CENT [Link] V DRIVE 1.0M 15p :CH SYNC ON GRN

4Y

4B

4A

3Y

3B

3A
R965

26

31

VCC
470 V.SYNCO_PD2 8 SYNCONGRN
:RN 680 [Link] PD0_CSYNCI R917
S1815

21

22
V SYNC H DRIVE IC902 1k

27

30
CONT R1814 SBLKOUT C911 V.SYNCI1 SN74HCT02AN
680 R954 2200 PD1_CSYNCO C955
C-BLANK

GND
:RN 4.7k 16V H SYNC 100p

1Y

1A

1B

2Y

2A

2B
28

29
S1802 VDD B
R1806 C905 H.SYNCI1
1k C937 R996 C946
0.1 1 2 3 4 5 6 7
:RN 470 10k 100p
16V D922
:PT D907
B
SIZE
R1818 1SS119 R977 RD5.6ESB2
1.5k 1k
:RN
S1816 C929
2 0.1 FB903
TILT R1819 R910 D910
1.5k 470k :PT D908
1 3 1SS119 1SS119
:RN
S1817
IC903
COLOR R1820 C942
3.3k
PST600D
1000
:RN 10V RESET
S1818
5V +5V +5V
R1815
FB905
100k R997 5V
:RN 1k
CN510
1P

1 1.2KV
R820 C811
27k 0.1 :PT
:RN R819 TO A BOARD CN301
33k D803 D804 C815 R824
:RN 1SS119 0.0022 10k
1SS119 12V
C822
5V 12V 0.0047
IC604 C813 R830 :PT
R823
TDA8138A 330k
0.01 47k
5V,12V,REG :PT :RN
C810
R817 R821 R822
4.7 C818 C817
47k C820 R815 68k R801 120k
C616 C814

7
OUTPUT2 35V :RN 0.1 100
4700p 0.0022 33k :RN 0.47 16V 0.22
:BP :PT
:PT :RN :FPRD :MPS
250V D650 D656 150V

6
31DF6-FC5 31DF6-FC5 OUTPUT1 C812
C634 0.0015
C635
9 10 470 :PT
C650 470

5
L650 NC 25V
FB604 220 80V 16V IC401 C821

FLYBACK
R603 R610 FB601 200V TDA8172 D801 330p 22 21 20 19 18 17 16 15 14 13 12

ADDVDD

IN_NEG
0.1 C803 R808 B
22k

P12
8 11 :HT GND V-OUT 1SS119

P22

P21

P20

P19

P18

P17

P16

P15

P14

P13
4
1/2W 16V 100p 470k
3W C651 L651 12
150V :RN

VDD
:RF :RS D651 R651 C969 R983 B

+IN

VSS

OUT
100
FB606 33k
EGP10D 100V DISABLE 0.001 82k R424

3
1W R809
:HT :PT :RN 12k R825 IC801
7 12 R666 390k 11

PEAKDET
:RS 10
C652 L652 10k :RN 1 2 3 4 5 6 7 1.5M :RN
R652 D652 PWM-CONT

RESET

TRING
EGP10D
2
1000 INPUT2

D402
0.12 EGP30D 25V
1/2W C420

REF

GND

VCC

PII
FB603 6 13 R423
Q602 :RF 0.0047 C404 R427

IO

CO

CI

I1
1
INPUT1 16V 5.6k 12k
IRFIBC40G :PT
:RN
220
:RN JW147
SW-REG OUT FB602 35V
C662 C532 155MM 1 2 3 4 5 6 7 8 9 10 11
:HT C520 R537
5 14 470 0.01
D603 100 22
TO HEAT L653 25V C405 200V
RD18ESB2 R667 D653 C653 D403 R425 :FPRD
C410 200V :PT
SINK 0.47 470 -10V 5V C403 6.8k 0.047 R811 C804
EGP20D GP08D
FB605 25V Q654 R664 0.1 1000 F 18k 0.001
C619 1/2W C808
4 15 2SB1094-LK 1.8 :PT 25V R536 :PT
0.0022 C678 :RF R831 C805 0.0015
S
D604 D654 1W R420 8.2k D526
:PT 330p PROT JW134 220 22
R607 UF4007G23 2kV 3DL41A :RS 47k D505 RGP02-20EL 5MM 12V
22 C806
RD10ESB2 L801 C819 C807
3 16
D602 R426 C402 R422 1000
C401 0.47 0.1
R654 HSS82 -10V R401 1.5 0.22 330 S R552 C534 16V
470 :MPS :PT
R609
C621 0.12 4.7k :FPRD100V 1W 2.2 10000p
R614 :RF 25V :PT :RS T501
0.22 D605 0.01 :FPRD 2kV
2.2k 2 17 R984 :HT Q503
3W
630V R674 :FBT F
HSS82 :PP 10k
1k IRFL9630G-LF GT001
:RS R615
R655 SW-REG
0.47 C618 R656 R421 R530
R613 1k C967 R976
:FPRD 1000 1k R966 2
330 1 18 Q903 100p 4.7k 1.8 82 2 HV
C607 D607 FB607
16V R673 R985
470k
1/2W 3W
0.0047 EGP10D 2SC3623-K B C533

+12V
10k 100 :RS
:PT BUFF 1500p
T601 16V
Q655 D401 R418
R531 500V 1
:SRT 2SC2785 1.8 1
80V MTZJ-4.7C 82 E R538
C608 R657 1/2W C509
R670 HEATER SW 10k 3W 6.8k R807
220 :RN L505 0.047
1k C614 :RS 56k
R605
35V 14
47k 100p :CH 14
R539 GT002
Q670 L507 R599
200k C802
:RN 82k 0.001
2SC2001TP 13
12V RELAY DRV 13
R606 C615
R604 1k 0.001 R631 C542
R608 C582 RV501
33k D608 :PT 220 C541 L504 0.01
10k 1000p 100k
R672 3W
RB441Q R611
Q529 0.0043
FOCUS
68 R550 2.50kV 2kV
:RS 180k 2SD1640Q
D609 10k :PP :PP
H-DRV D508 C513 R540 R598
R671 MTZJ-3.6A T504 0.047 SG501
C609 R612 R509
SB34O 17 C548 33k
R541
22k
1k 0.1 :HDT C583 200V 17 0.33
D670 15k Q528 4.7 Q507 FB501 0.022 8.2k C531
:PT D504 :PT 100V 0.1
1SS119 2SC3209LK :FPRD 2SC5129 0.45UH 100V
3DL41A :PT
1 2 3 4 5 6 7 8 R658 H-DRV 1 8 H OUT :PT
CN512
16
680 16 1P
D595
VCC

OUT

GND

OVP

CIS
VC

DD

2 1 FB502
FLDBK

C549 R543 R542

IC601 150V
1SS119 D596 0.1
C528
2.2k 2.2k 12V GND
RY601 12V
MC44603P R914 2 7 R508 1SS119 22
R511 :PT :RN :RN
6 5 2.2k 1.5 11
SW REG CONTROL C523 47 11
C628 C521 R551 C599 R523
RFSTBY

RPSTBY

0.022 3W
D509
SS/DM

0.1 R555 1.0 1.2k 100V 10 0.47 R544

RREF

SYNC

D501 EGP10D
VFB

TH602 4 3 :PT 0.47 :RN :PT 100V 3 6 :FPRD 56k

EA

CT

:POS
Q504 :FPRD FMQ-G5FMS 8 :RN
6
2SC2785 R506
Q510 R526 R545 C519
16 15 14 13 12 11 10 9
D614 H DRIVE 4 1.5 IRFPE40LF20 FB525 0.47 47k 2.2 C406 CN503
RD8.2ESB2 R500 D502 4 3W HV REG OUT FB524 :FPRD R564 :RN 0.068 2P
R623 R621 C611 C610 C502 9 2.2k :PT
R619 1.0 3 100 R504 5
C622 10k 27k
4.7k 560p 0.01 :FPRD
RD18ESB2 220
D601 :RN :MPS B R532 1 ROTATION+
4700p :PT 2W C540 R553
250V GBU4JL S 0.0022 2.2k D510 4.7 R408
:RS :FPRD 2 4 2 ROTATION-
6 1
C527 R546 2kV 10 EGP10D 1.5
Q502 22 :PP
4
:FPRD
3 S 100p D598
DGC1 3 C620 R501 IRFU214 :FPRD C514 R554 D511 IC400
C500 500V R563 C547
390 22k H-DRIVE OUT RD18ESB2 470 2.2k LA6500-FA
0.22 B T505 2.2k 25V
470 RD27ESB2 R411
NC 2
2 1
400V 5 2 Q505 :MPS C565 7 25V D515 10k ROTATION DRV R407 R410
:HT :HST 8
2SA1175 R527
0.22
EGP10D :RN 12k 22
DGC2 1 C612 220 R533 :RN 1W
IC603 H DRIVE :MPS
0.01 3W 620k :RS
VA601 MOC8105TVZ R661 1 5 1 3 5
CN601 4 :PT 4 3 12 12
PHOTO COUPLER 470k 12 9 R534 R535
12V C518 D522
3P 3300p 4 R528 C569 91k 150k
RCC CTRL 68 1SS119 0.01 C515 C516 C517
500V D503
TH601 C930 2 1 2 3 3W :PT 0.01 1.0 0.01
R659 1SS119 R529
:PT R412
22 :RS 100k 630V
390k L513
:PP 1k
C675 :RN :HLC
C604 C603 R602 :RN
3

0.001
4700p 4700p 1 :PT R515 16V
250V 250V 10W IC652 330k
TL431ACLPRP
1

R662 R547 C503 R524 -10V

ERROR AMP R512 R514 R565
R660 33k 3.9k 2.2 160V 27 2W :RS
8.2k 120k 10k 390k 1 12
C602 1 12
2

:RN R663
1.0 L501 R525
250V 10k C505 Q509
10 R556 1.2mmH 5.6k
:PP
1.0k 11
2SD1275-Q
11 R549 B-#SV3449<MANUAL/CH>-D..
Q656 1/2W AMP
1 4 R665 C570 C576 C562 10
C593 12V L506 R567 2W
2SC2785 10k 0.56 0.22 0.1 R521
LF601 0.18 10 :RS
:LFT STBY CONTROL 3 10 250V
250V 250V 400V 2W 4.7
2SC3941A

3 10 :PP Q515
DF-AMP

:RS :FPRD
Q500

2 3 R513 2SC3209LK
R510
Q513 Q512 R505
10k 4.7 Q514 BUFF
C601 2SK1904 2SK1904 22k C598
4 9 2SK1904 Q508
2SA1175

0.47 4 9 R519 0.1

2SB949-Q
Q501

BUFF

250V 47k :PT

FB614 FB615 R601 C567 C568 R503
C506 AMP
560k 1/2W :RC S 0.01 S 0.01 S 47k C512
0.01 C508 5 8 TH501
5 8 :PT :PT 0.1
F601 C605 :PT 33p :PT
5V R520 R522
4A FB611 12V 80V 150V 2.0kV R518
220p 6 1k D506 1k
250V FB610 1k
250V
6 7
C566
R507 :FPRD :FPRD RD27ESB2 :FPRD
B R548 6 7 0.01
S2

S1

S0

C617 4.7k 47k

0.001 C550 :PT
C606 7 0.36
100V T503
220p :PT 250V
250V 5 C507 :DFT :PP R517
-10V C529 FB503
0.001 1k
CN610 B
:FPRD 0.1
8 500V 400V S CAP CHANGE
GND B
FB612 FB613
10

FB608 FB609 CN504

9

L G N
1

GND

GND

+5V

H2

H1

GND

NC
+12V

+80V

+150V

H DY+

H DY+

H DY-

H DY-

V DY-

V DY+

GND
N

CN605

CN600 CN501
THP601A

CN505
2P
THP601

10P 6P
G

WHT DY

AC IN
TO A BOARD

CN305
5-4. SEMICONDUCTORS

EGP10D UF3ML-6505 2SC5022-02 EGP30D TDA6103Q SB340L-6489 5TUZ52

RB441QT-77 EGP20GPKG23 RGP02-20EL-6394 2SA1162-G
RD5.6ES-B2 GP08D CATHODE 3DL41A (LC6-15) CATHODE
RD8.2ES-B2 CATHODE HSS 82 CATHODE
RD10ES-B2
RD18ES-BS C
RD27ES-B2
1SS119-25TD
UZ-4.7BSC B
1
9
2
8
E 364
7
5 546 CATHODE
ANODE 7 28
3
B C 1 9 ANODE
ANODE E
ANODE ANODE

MM1382 SN74HCT02AN SNY425 TDA9105S UPC6753 ST7272N5B1/CKO MC 44603P TL 431CLP

14 8 24 13 22 12 16 9
28 15 42 22 56 29

1 28
1 12 1 21
1 14 1 7 1 11
1 8

M5218AP GP104005-E-G23 GBU4JL-6088 TDA 8172 FMQ-G5FMS TDA6103Q LA 6500-FA SEL1422G-C

NJM4558D SG232D-658
8 CATHODE SEL1922D-C
7 SY432W-M-658
{
‘
‘
|

{
6 ‘
1 5 ‘ 1 CATHODE
2 | 1 1
3 ANODE 7
2
3 ANODE
4 ANODE 5 CATHODE
8
7
6
5
1
2SC3941A-Q2
(TA) 2SA1175-HFE 2SC3209-LK 2SC2001TP-K2 2SB1094F 2SC5129 LM2405T PST600D-T
3 2SC2785-HFE 2SB1375
4
2SB1565F
LETTER SIDE

1
B 1 Vcc
E C E C
B C GND
OUT
E C
B E C
B
B B C E E 11
14

IRFIBC40G-LF38 2SD1640Q M0C8105TV IRFI9630 DTC124ES-TP 2SK1904 IRFPE40LF20 2SC3623K

6 IRFU214

1
i ‘ 2j
i { j3
i ‘ j 5
4
or 12
3
6
5 G
1 4
i ‘ 2j G
GG S D
E 1 E G D
G
D
1 2
C i | j3 2 D
S DS C D
S 3
B
i ‘ j 3 B S S
 CPD-200ES
SECTION 6
EXPLODED VIEWS
Note:
• Items with no part number and no descrip- • Items marked " * " are not stocked
tion are not stocked because they are sel- since they are seldom required for routine The components identified by shading
dom required
[Link]. PART [Link] routine service.
DESCRIPTION service. Some delay [Link].
REMARK be anticipated
PART NO. and
DESCRIPTION
mark ¡ a re critical forREMARK
safety.
when ordering these items.
Replace only with part number specified.
• The component parts of an assembly are
indicated by the reference numbers in the
remarks column. Note:
Les composants identifies per un trame
et une marque ¡ sont critiques pour la
6-1. CHASSIS securite. Ne les remplacer que par une
piece portant le numero specifie.

r 7-685-648-79 SCREW +BVTP 3x12

¢ 7-685-663-71 SCREW +BVTP 4x16 31 32
7-685-882-09 SCREW +BVTT 4x10
7-685-646-79 SCREW +BVTP 3x8

27 16 15

28
34 15
33 14
14
13
13
29 7
3530 31
4
86 77
5 108 22
23
12 19
22
21
23
1012
11 11 21
56 18
20
99 19
20
24
17
18
24
25
16
17
25
26
4

33 11 28
26
27
22
32 29
4
30

[Link]. PART NO. DESCRIPTION REMARK [Link]. PART NO. DESCRIPTION REMARK

1* X-4034-876-1 BEZEL ASSY 2-3 19 1-543-653-11 CORE ASSY,BEAD (DIVISION TYPE)

2 4-060-596-01 SPRING, COMPRESSION 20 4-389-025-01 SCREW (M4x8)([Link])
3 4-060-598-01 BUTTON, POWER 21 7-685-659-71 SCREW + BVTT 4x8 (S)
4* 4-060-152-01 LABEL, ENERGY STAR 22 * 4-060-151-01 STOPPER, CABLE
5¡ 8-738-733-82 ITC ASSY (17FRFM-R2) 23 1-775-535-11 CABLE ASSY VIDEO (15P D-SUB)

6 ¡ 8-738-731-05 CRT, 17FRSM (M41LKN70X) 24 * 4-060-150-01 BRACKET, CABLE

7 4-060-166-01 SPACER, DY 25 * 4-060-612-01 COVER, BOTTOM
8 ¡ 1-452-923-21 NECK ASSY (NA-2914) 26 * 4-060-178-01 HOLDER, STAND
9 ¡ 8-451-487-11 DY Y17FRG-M 27 4-060-183-01 STOPPER (A)
10 1-500-386-11 FILTER CLAMP (FERRITE CORE) 28 * 4-060-613-01 SLIDER

11 * A-1298-231-A A BOARD, COMPLETE 29 * 4-060-180-01 RING, TILT SWIVEL

13 4-060-603-01 SPRING, TENSION 30 * X-4034-879-1 STAND BASE, ASSY
14 ¡ 1-416-282-21 COIL, DEMAGNETIZATION 31 X-4034-877-1 CABINET ASSY
15 * 4-056-260-11 SPACER, DGC 32 * 4-064-116-01 LABEL, INFORMATION
33 4-060-155-01 HOLDER, HV CABLE
16 4-365-808-01 SCREW (5), TAPPING
17 * A-1346-658-A D BOARD, COMPLETE 34 1-452-032-00 MAGNET, DISC
18 ¡ 1-453-240-21 TRANSFORMER ASSY, FLYBACK(NX-4103//JIE4) 35 * X-4034-792-1 PERMALLOY ASSY, STAND

— 29 —
CPD200ES

6-2. PACKING MATERIALS

[Link]. PART NO. DESCRIPTION REMARK [Link]. PART NO. DESCRIPTION REMARK

53
52

50 51

54

55

56

[Link]. PART NO. DESCRIPTION REMARK

50 4-060-206-01 DISK, WINDOWS 95

51 3-860-654-11 MANUAL, INSTRUCTION
52 * 4-060-618-01 CUSHION,TOP
53 ¡ 1-783-481-11 CORD SET, POWER
54 * 4-060-620-01 BAG, POLYETHYLENE
55 * 4-060-617-01 CUSHION, BOTTOM
56 * 4-061-139-01 INDIVIDUAL CARTON

— 30 —
 CPD-200ES

A
SECTION 7
ELECTRICAL PARTS LIST
Note: The components identified by [ in this manual RESISTORS
have been carefully factory-selected for each
set in order to satisfy regulations regarding X-
• All resistors are in ohms
[Link]. PART NO.
The components DESCRIPTION
identified by shading REMARK [Link]. PART NO. • F : nonflammable
DESCRIPTION REMARK
and mark ¡ a re critical for safety. ray radiation. Should replacement be required,
Replace only with part number specified. replace only with the value originally used.
CAPACITORS
• Items marked " * " are not stocked since they • MF = µF
are seldom required for routine service. Some
Note:
delay should be anticipated when ordering
INDUCTORS
Les composants identifies per un trame these items.
• UH = µH, MMH = mH
et une marque ¡ sont critiques pour la
securite. Ne les remplacer que par une • All variable and adjustable resistors have
piece portant le numero specifie. When indicating parts by reference
characteristic curve B, unless otherwise
number, please include the board name.
noted.

A [Link].
C031
PART NO.
1-162-318-11
DESCRIPTION
CERAMIC 0.001MF 10%
REMARK
500V
[Link]. PART NO. DESCRIPTION REMARK C035 1-115-349-51 CERAMIC 0.01MF 2KV
C036 1-163-231-11 CERAMIC CHIP 15PF 5% 50V
* A-1298-231-A A BOARD, COMPLETE C037 1-126-933-11 ELECT 100MF 20% 16V
C040 1-164-004-11 CERAMIC CHIP 0.1MF 10% 25V
4-382-854-01 SCREW (M3X8), P, SW (+)
C041 1-164-004-11 CERAMIC CHIP 0.1MF 10% 25V
CAPACITOR C055 1-163-231-11 CERAMIC CHIP 15PF 5% 50V
C088 1-126-934-11 ELECT 220MF 20% 16V
C001 1-136-169-00 FILM 0.22MF 5% 50V C092 1-164-004-11 CERAMIC CHIP 0.1MF 10% 25V
C002 1-137-528-11 FILM 0.1MF 10% 250V C100 1-104-664-11 ELECT 47MF 20% 25V
C003 1-137-528-11 FILM 0.1MF 10% 250V
C004 1-164-004-11 CERAMIC CHIP 0.1MF 10% 25V C101 1-126-960-11 ELECT 1MF 20% 50V
C005 1-163-263-11 CERAMIC CHIP 330PF 5% 50V C103 1-164-004-11 CERAMIC CHIP 0.1MF 10% 25V
C104 1-107-823-11 CERAMIC CHIP 0.47MF 10% 16V
C006 1-126-934-11 ELECT 220MF 20% 16V C105 1-164-004-11 CERAMIC CHIP 0.1MF 10% 25V
C007 1-104-664-11 ELECT 47MF 20% 25V C106 1-137-528-11 FILM 0.1MF 10% 250V
C008 1-164-004-11 CERAMIC CHIP 0.1MF 10% 25V
C009 1-164-004-11 CERAMIC CHIP 0.1MF 10% 25V C107 1-164-346-11 CERAMIC CHIP 1MF 16V
C010 1-164-004-11 CERAMIC CHIP 0.1MF 10% 25V C108 1-164-004-11 CERAMIC CHIP 0.1MF 10% 25V
C109 1-163-259-91 CERAMIC CHIP 220PF 5% 50V
C011 1-106-220-00 MYLAR 0.1MF 10% 100V C110 1-163-227-11 CERAMIC CHIP 10PF 5% 50V
C012 1-164-004-11 CERAMIC CHIP 0.1MF 10% 25V C201 1-126-960-11 ELECT 1MF 20% 50V
C013 1-126-934-11 ELECT 220MF 20% 16V
C014 1-107-932-11 ELECT 47MF 20% 100V C202 1-164-004-11 CERAMIC CHIP 0.1MF 10% 25V
C015 1-164-004-11 CERAMIC CHIP 0.1MF 10% 25V C203 1-164-004-11 CERAMIC CHIP 0.1MF 10% 25V
C204 1-107-823-11 CERAMIC CHIP 0.47MF 10% 16V
C016 1-126-933-11 ELECT 100MF 20% 16V C205 1-164-004-11 CERAMIC CHIP 0.1MF 10% 25V
C017 1-126-933-11 ELECT 100MF 20% 16V C206 1-137-528-11 FILM 0.1MF 10% 250V
C018 1-107-746-11 ELECT 10MF 20% 200V
C019 1-164-004-11 CERAMIC CHIP 0.1MF 10% 25V C207 1-164-346-11 CERAMIC CHIP 1MF 16V
C020 1-163-227-11 CERAMIC CHIP 10PF 5% 50V C209 1-163-259-91 CERAMIC CHIP 220PF 5% 50V
C301 1-126-960-11 ELECT 1MF 20% 50V
C021 1-164-232-11 CERAMIC CHIP 0.01MF 10% 50V C302 1-164-004-11 CERAMIC CHIP 0.1MF 10% 25V
C022 1-164-346-11 CERAMIC CHIP 1MF 16V C303 1-164-004-11 CERAMIC CHIP 0.1MF 10% 25V
C023 1-163-275-11 CERAMIC CHIP 0.001MF 5% 50V
C024 1-163-263-11 CERAMIC CHIP 330PF 5% 50V C304 1-107-823-11 CERAMIC CHIP 0.47MF 10% 16V
C025 1-163-251-11 CERAMIC CHIP 100PF 5% 50V C305 1-164-004-11 CERAMIC CHIP 0.1MF 10% 25V
C306 1-137-528-11 FILM 0.1MF 10% 250V
C026 1-163-251-11 CERAMIC CHIP 100PF 5% 50V C307 1-164-346-11 CERAMIC CHIP 1MF 16V
C027 1-164-346-11 CERAMIC CHIP 1MF 16V C309 1-163-259-91 CERAMIC CHIP 220PF 5% 50V
C028 1-107-888-11 ELECT 47MF 20% 25V
C029 1-107-823-11 CERAMIC CHIP 0.47MF 10% 16V C330 1-107-905-11 ELECT 4.7MF 20% 50V
C030 1-164-489-11 CERAMIC CHIP 0.22MF 10% 16V C334 1-164-004-11 CERAMIC CHIP 0.1MF 10% 25V
C351 1-137-528-11 FILM 0.1MF 10% 250V

— 31 —
CPD200ES

A
Note: Note: Les composants identifies per un trame et une marque
The components identified by shading
and mark ¡ are critical for safety. ¡ sont critiques pour la securite. Ne les remplacer
Replace only with part number specified. que par une piece portant le numero specifie.

[Link]. PART NO. DESCRIPTION REMARK [Link]. PART NO. DESCRIPTION REMARK

CONNECTOR FB103 1-500-104-21 FERRITE

FB104 1-412-911-11 FERRITE
CN301 1-506-108-41 PIN, CONNECTOR (TERMINAL PIN) FB110 1-412-911-11 FERRITE
CN302 1-695-915-11 TAB (CONTACT) FB201 ¡ 1-500-104-21 FERRITE
CN303 1-695-915-11 TAB (CONTACT) FB202 ¡ 1-414-793-21 FERRITE
CN305 1-564-513-11 PLUG, CONNECTOR 10P FB203 1-500-104-21 FERRITE
CN306 * 1-564-510-11 PLUG, CONNECTOR 7P
FB210 1-412-911-11 FERRITE
CN307 * 1-564-512-11 PLUG, CONNECTOR 9P FB301 ¡ 1-500-104-21 FERRITE
CN309 1-564-511-11 PLUG, CONNECTOR 8P FB302 ¡ 1-414-793-21 FERRITE
CN310 * 1-564-507-11 PLUG, CONNECTOR 4P FB303 1-500-104-21 FERRITE
CN311 * 1-564-507-11 PLUG, CONNECTOR 4P FB310 1-412-911-11 FERRITE
CN399 1-695-915-11 TAB (CONTACT)
IC
DIODE
IC001 8-759-474-78 IC MM1382
D002 8-719-911-19 DIODE 1SS119-25 IC002 8-759-435-33 IC LM2405T
D014 8-719-911-19 DIODE 1SS119-25 IC003 8-759-399-76 IC SNY425
D016 8-719-109-89 DIODE RD5.6ESB2 IC004 8-759-434-40 IC TDA6103Q/N3,112
D017 8-719-109-89 DIODE RD5.6ESB2 IC005 8-759-634-51 IC M5218AP
D101 8-719-911-19 DIODE 1SS119-25
JACK
D102 8-719-911-19 DIODE 1SS119-25
D104 8-719-970-83 DIODE HSS82 J001 ¡ 1-251-598-11 SOCKET, CRT
D105 8-719-970-83 DIODE HSS82
D106 8-719-970-83 DIODE HSS82 COIL
D201 8-719-911-19 DIODE 1SS119-25
L001 1-412-537-31 INDUCTOR 100UH
D202 8-719-911-19 DIODE 1SS119-25 L101 1-407-500-00 INDUCTOR 4.7MMH
D204 8-719-970-83 DIODE HSS82 L105 1-410-750-41 INDUCTOR 0.47UH
D205 8-719-970-83 DIODE HSS82 L201 1-407-500-00 INDUCTOR 4.7MMH
D206 8-719-970-83 DIODE HSS82 L205 1-410-750-41 INDUCTOR 0.47UH
D301 8-719-911-19 DIODE 1SS119-25
L301 1-407-500-00 INDUCTOR 4.7MMH
D302 8-719-911-19 DIODE 1SS119-25 L305 1-410-750-41 INDUCTOR 0.47UH
D304 8-719-970-83 DIODE HSS82
D305 8-719-970-83 DIODE HSS82 TRANSISTOR
D306 8-719-970-83 DIODE HSS82
D307 8-719-110-49 DIODE RD18ESB2 Q001 8-729-032-61 TRANSISTOR 2SC5022-02
Q002 8-729-216-22 TRANSISTOR 2SA1162-G
FERRITE BEAD Q003 8-729-216-22 TRANSISTOR 2SA1162-G
Q004 8-729-120-28 TRANSISTOR 2SC1623-L5L6
FB001 1-412-911-11 FERRITE Q005 8-729-216-22 TRANSISTOR 2SA1162-G
FB003 1-412-911-11 FERRITE Q006 8-729-216-22 TRANSISTOR 2SA1162-G
FB004 1-412-911-11 FERRITE
FB005 1-412-911-11 FERRITE RESISTOR
FB006 1-412-911-11 FERRITE
R001 1-216-049-91 RES,CHIP 1K 5% 1/10W
FB007 1-412-911-11 FERRITE R002 1-216-661-11 METAL CHIP 2.7K 0.50% 1/10W
FB008 1-412-911-11 FERRITE R003 1-216-101-00 RES,CHIP 150K 5% 1/10W
FB009 1-412-911-11 FERRITE R004 1-216-085-00 RES,CHIP 33K 5% 1/10W
FB010 1-412-911-11 FERRITE R005 1-216-049-91 RES,CHIP 1K 5% 1/10W
FB011 1-412-911-11 FERRITE
R006 1-216-025-91 RES,CHIP 100 5% 1/10W
FB012 1-412-911-11 FERRITE R007 1-216-049-91 RES,CHIP 1K 5% 1/10W
FB013 1-412-911-11 FERRITE R008 1-216-025-91 RES,CHIP 100 5% 1/10W
FB101 ¡ 1-500-104-21 FERRITE R010 1-216-049-91 RES,CHIP 1K 5% 1/10W
FB102 ¡ 1-414-793-21 FERRITE R011 1-216-091-00 RES,CHIP 56K 5% 1/10W

— 32 —
 CPD-200ES

A
Note: The components identified by shading
Note: Les composants identifies per un trame et une marque
and mark ¡ are critical for safety. ¡ sont critiques pour la securite. Ne les remplacer
Replace only with part number specified. que par une piece portant le numero specifie.

[Link]. PART NO. DESCRIPTION REMARK [Link]. PART NO. DESCRIPTION REMARK

R012 1-216-109-00 RES,CHIP 330K 5% 1/10W R202 1-216-017-91 RES,CHIP 47 5% 1/10W

R013 1-216-675-11 METAL CHIP 10K 0.50% 1/10W R203 1-216-097-91 RES,CHIP 100K 5% 1/10W
R014 1-216-025-91 RES,CHIP 100 5% 1/10W R204 1-216-021-00 RES,CHIP 68 5% 1/10W
R015 1-216-053-00 RES,CHIP 1.5K 5% 1/10W R205 1-216-037-00 RES,CHIP 330 5% 1/10W
R016 1-216-073-00 RES,CHIP 10K 5% 1/10W R206 1-216-073-00 RES,CHIP 10K 5% 1/10W

R017 1-216-025-91 RES,CHIP 100 5% 1/10W R207 1-216-073-00 RES,CHIP 10K 5% 1/10W
R018 1-216-025-91 RES,CHIP 100 5% 1/10W R208 1-216-069-00 RES,CHIP 6.8K 5% 1/10W
R019 1-216-025-91 RES,CHIP 100 5% 1/10W R209 1-216-121-91 RES,CHIP 1M 5% 1/10W
R020 1-216-025-91 RES,CHIP 100 5% 1/10W R210 1-216-254-00 RES,CHIP 220K 5% 1/8W
R021 1-216-025-91 RES,CHIP 100 5% 1/10W R211 1-249-412-11 CARBON 390 5% 1/4W

R022 1-216-049-91 RES,CHIP 1K 5% 1/10W R214 1-216-061-00 RES,CHIP 3.3K 5% 1/10W

R024 1-216-065-91 RES,CHIP 4.7K 5% 1/10W R215 1-249-401-11 CARBON 47 5% 1/4W F
R025 1-216-065-91 RES,CHIP 4.7K 5% 1/10W R251 1-202-549-00 SOLID 100 20% 1/2W
R026 1-216-073-00 RES,CHIP 10K 5% 1/10W R262 1-216-049-91 RES,CHIP 1K 5% 1/10W
R027 1-218-756-11 METAL CHIP 150K 0.50% 1/10W R301 1-216-022-00 RES,CHIP 75 5% 1/10W

R028 1-216-372-11 METAL OXIDE 1.8 5% 2W F R302 1-216-017-91 RES,CHIP 47 5% 1/10W

R029 1-216-101-00 RES,CHIP 150K 5% 1/10W R303 1-216-097-91 RES,CHIP 100K 5% 1/10W
R030 1-216-097-91 RES,CHIP 100K 5% 1/10W R304 1-216-013-00 RES,CHIP 33 5% 1/10W
R031 1-216-049-91 RES,CHIP 1K 5% 1/10W R305 1-216-037-00 RES,CHIP 330 5% 1/10W
R032 1-216-665-11 METAL CHIP 3.9K 0.50% 1/10W R306 1-216-073-00 RES,CHIP 10K 5% 1/10W

R033 1-216-679-11 METAL CHIP 15K 0.50% 1/10W R307 1-216-073-00 RES,CHIP 10K 5% 1/10W
R035 1-216-017-91 RES,CHIP 47 5% 1/10W R308 1-216-069-00 RES,CHIP 6.8K 5% 1/10W
R036 1-216-017-91 RES,CHIP 47 5% 1/10W R309 1-216-121-91 RES,CHIP 1M 5% 1/10W
R039 1-218-764-11 METAL CHIP 330K 0.50% 1/10W R310 1-216-254-00 RES,CHIP 220K 5% 1/8W
R040 1-216-121-91 RES,CHIP 1M 5% 1/10W R311 1-249-412-11 CARBON 390 5% 1/4W

R045 1-216-057-00 RES,CHIP 2.2K 5% 1/10W R314 1-216-061-00 RES,CHIP 3.3K 5% 1/10W
R048 1-211-885-21 METAL 2.2M 5% 1W R315 1-249-401-11 CARBON 47 5% 1/4W F
R049 1-218-760-11 METAL CHIP 220K 0.50% 1/10W R351 1-202-549-00 SOLID 100 20% 1/2W
R053 1-219-621-91 METAL 22M 10% 1/4W R362 1-216-049-91 RES,CHIP 1K 5% 1/10W
R057 1-216-057-00 RES,CHIP 2.2K 5% 1/10W
SPARK GAP
R058 1-216-041-00 RES,CHIP 470 5% 1/10W
R064 1-202-830-00 SOLID 10K 20% 1/2W SG001 ¡ 1-519-422-11 GAP, SPARK
R077 1-216-047-91 RES,CHIP 820 5% 1/10W SG003 ¡ 1-517-499-21 GAP, SPARK
R101 1-216-022-00 RES,CHIP 75 5% 1/10W SG101 ¡ 1-517-499-21 GAP, SPARK
R102 1-216-017-91 RES,CHIP 47 5% 1/10W SG201 ¡ 1-517-499-21 GAP, SPARK
SG301 ¡ 1-517-499-21 GAP, SPARK
R103 1-216-675-11 METAL CHIP 10K 0.50% 1/10W
R104 1-216-017-91 RES,CHIP 47 5% 1/10W CRYSTAL
R105 1-216-037-00 RES,CHIP 330 5% 1/10W
R106 1-216-073-00 RES,CHIP 10K 5% 1/10W X1 1-567-890-11 VIBRATOR, CRYSTAL
R107 1-216-073-00 RES,CHIP 10K 5% 1/10W

R108 1-216-069-00 RES,CHIP 6.8K 5% 1/10W

R109 1-216-121-91 RES,CHIP 1M 5% 1/10W
R110 1-216-254-00 RES,CHIP 220K 5% 1/8W
R111 1-249-412-11 CARBON 390 5% 1/4W
R114 1-216-061-00 RES,CHIP 3.3K 5% 1/10W

R115 1-249-401-11 CARBON 47 5% 1/4W F

R151 1-202-549-00 SOLID 100 20% 1/2W
R162 1-216-049-91 RES,CHIP 1K 5% 1/10W
R201 1-216-022-00 RES,CHIP 75 5% 1/10W

— 33 —
CPD200ES

D
Note: The components identified by shading
Note: Les composants identifies per un trame et une marque
and mark ¡ are critical for safety. ¡ sont critiques pour la securite. Ne les remplacer
Replace only with part number specified. que par une piece portant le numero specifie.

[Link]. PART NO. DESCRIPTION REMARK [Link]. PART NO. DESCRIPTION REMARK

C541 ¡ 1-109-997-11 FILM 0.0043MF 3% 2.5KV

D C542
C547
1-137-370-11
1-126-941-11
FILM
ELECT
0.01MF
470MF
5%
20%
50V
25V
C548 1-137-425-11 FILM 0.33MF 10% 100V
* A-1346-658-A D BOARD, COMPLETE
C549 1-130-495-00 FILM 0.1MF 5% 50V
C550 1-117-206-21 FILM 0.36MF 5% 250V
1-533-223-11 HOLDER, FUSE
C562 1-107-846-11 FILM 0.1MF 5% 400V
* 1-900-801-67 CONNECTOR ASSY
C565 1-136-169-00 FILM 0.22MF 5% 50V
4-060-502-01 HOLDER, LED (A)
C566 1-137-370-11 FILM 0.01MF 5% 50V
4-382-854-11 SCREW (M3X10), P, SW (+)
4-389-025-01 SCREW (M4) (EXT TOOTH WASHER)
C567 1-137-370-11 FILM 0.01MF 5% 50V
7-685-647-79 SCREW +BVTP 3X10 TYPE2
C568 1-137-370-11 FILM 0.01MF 5% 50V
C569 1-137-370-11 FILM 0.01MF 5% 50V
CAPACITOR
C570 1-115-519-11 FILM 0.56MF 5% 250V
C576 1-115-514-11 FILM 0.22MF 5% 250V
C401 1-128-528-11 ELECT 470MF 20% 25V
C402 1-106-228-00 MYLAR 0.22MF 10% 100V
C582 1-161-754-00 CERAMIC 0.001MF 10% 2KV
C403 1-130-495-00 FILM 0.1MF 5% 50V
C583 1-106-375-12 MYLAR 0.022MF 10% 100V
C404 1-107-894-11 ELECT 220MF 20% 35V
C593 1-117-662-71 FILM 0.18MF 5% 250V
C405 1-101-006-00 CERAMIC 0.047MF 50V
C598 1-130-495-00 FILM 0.1MF 5% 50V
C599 1-128-582-11 ELECT 10MF 20% 100V
C406 1-137-375-11 FILM 0.068MF 5% 50V
C410 1-107-914-11 ELECT 1000MF 20% 25V
C601 ¡ 1-104-708-11 FILM 0.47MF 20% 250V
C420 1-137-368-11 FILM 0.0047MF 5% 50V
C602 ¡ 1-107-533-11 FILM 1MF 20% 250V
C500 1-136-169-00 FILM 0.22MF 5% 50V
C603 ¡ 1-113-912-11 CERAMIC 0.0047MF 20% 250V
C502 1-137-370-11 FILM 0.01MF 5% 50V
C604 ¡ 1-113-912-11 CERAMIC 0.0047MF 20% 250V
C605 ¡ 1-113-896-11 CERAMIC 220PF 10% 250V
C503 1-107-667-11 ELECT 2.2MF 20% 160V
C505 1-126-964-11 ELECT 10MF 20% 50V
C606 ¡ 1-113-896-11 CERAMIC 220PF 10% 250V
C506 1-137-370-11 FILM 0.01MF 5% 50V
C607 1-137-368-11 FILM 0.0047MF 5% 50V
C507 1-162-318-11 CERAMIC 0.001MF 10% 500V
C608 1-107-894-11 ELECT 220MF 20% 35V
C508 1-109-843-11 CERAMIC 33PF 5% 2KV
C609 1-130-495-00 FILM 0.1MF 5% 50V
C610 1-102-115-00 CERAMIC 560PF 10% 50V
C509 1-137-374-11 FILM 0.047MF 5% 50V
C512 1-130-495-00 FILM 0.1MF 5% 50V
C611 1-136-177-00 FILM 1MF 5% 50V
C513 1-106-383-00 MYLAR 0.047MF 10% 200V
C612 1-137-370-11 FILM 0.01MF 5% 50V
C514 1-126-941-11 ELECT 470MF 20% 25V
C614 1-102-973-00 CERAMIC 100PF 5% 50V
C515 1-136-203-11 FILM 10000PF 5% 630V
C615 1-137-364-11 FILM 0.001MF 5% 50V
C616 1-113-912-11 CERAMIC 0.0047MF 20% 250V
C516 1-126-960-11 ELECT 1MF 20% 50V
C517 1-137-370-11 FILM 0.01MF 5% 50V
C617 1-106-343-00 MYLAR 0.001MF 10% 100V
C518 1-165-136-11 CERAMIC 3300PF 10% 500V
C618 1-107-884-11 ELECT 1000MF 20% 16V
C519 1-126-961-11 ELECT 2.2MF 20% 50V
C619 1-137-366-11 FILM 0.0022MF 5% 50V
C520 1-107-955-11 ELECT 100MF 20% 200V
C620 ¡ 1-109-984-11 ELECT(BLOCK) 390MF 20% 400V
C621 1-136-203-11 FILM 10000PF 5% 630V
C521 1-126-960-11 ELECT 1MF 20% 50V
C523 1-106-375-12 MYLAR 0.022MF 10% 100V
C622 ¡ 1-113-912-11 CERAMIC 0.0047MF 20% 250V
C527 1-162-117-00 CERAMIC 100PF 10% 500V
C628 1-130-495-00 FILM 0.1MF 5% 50V
C528 1-126-965-11 ELECT 22MF 20% 50V
C634 1-126-941-11 ELECT 470MF 20% 25V
C529 1-107-846-11 FILM 0.1MF 5% 400V
C635 1-126-935-11 ELECT 470MF 20% 16V
C650 1-125-700-11 ELECT(BLOCK) 220MF 20% 200V
C531 1-130-495-00 FILM 0.1MF 5% 50V
C532 1-107-364-11 MYLAR 0.01MF 10% 200V
C651 1-107-933-11 ELECT 100MF 20% 100V
C533 1-164-735-11 CERAMIC 0.0015MF 10% 500V
C652 1-107-914-11 ELECT 1000MF 20% 25V
C534 1-115-349-51 CERAMIC 0.01MF 2KV
C653 1-126-941-11 ELECT 470MF 20% 25V
C536 1-106-375-12 MYLAR 0.022MF 10% 100V
C540 ¡ 1-136-064-00 FILM 2200PF 3% 2KV C662 1-126-941-11 ELECT 470MF 20% 25V
C675 1-137-364-11 FILM 0.001MF 5% 50V

— 34 —
 CPD-200ES

D
Note: The components identified by shading
Note: Les composants identifies per un trame et une marque
and mark ¡ are critical for safety. ¡ sont critiques pour la securite. Ne les remplacer
Replace only with part number specified. que par une piece portant le numero specifie.

[Link]. PART NO. DESCRIPTION REMARK [Link]. PART NO. DESCRIPTION REMARK

C678 1-162-115-00 CERAMIC 330PF 10% 2KV C933 1-126-934-11 ELECT 220MF 20% 16V
C802 1-102-074-00 CERAMIC 0.001MF 10% 50V C934 1-126-961-11 ELECT 2.2MF 20% 50V
C803 1-102-106-00 CERAMIC 100PF 10% 50V C935 1-136-169-00 FILM 0.22MF 5% 50V
C804 1-137-364-11 FILM 0.001MF 5% 50V C937 1-126-935-11 ELECT 470MF 20% 16V

C805 1-126-965-11 ELECT 22MF 20% 50V C939 1-137-374-11 FILM 0.047MF 5% 50V
C806 1-126-767-11 ELECT 1000MF 20% 16V C940 1-137-374-11 FILM 0.047MF 5% 50V
C807 1-130-495-00 FILM 0.1MF 5% 50V C941 1-136-169-00 FILM 0.22MF 5% 50V
C808 1-137-365-11 FILM 0.0015MF 5% 50V C942 1-126-926-11 ELECT 1000MF 20% 10V
C810 1-107-713-11 ELECT 4.7MF 20% 35V C943 1-137-372-11 FILM 0.022MF 5% 50V

C811 1-130-495-00 FILM 0.1MF 5% 50V C944 1-137-366-11 FILM 0.0022MF 5% 50V
C812 1-137-365-11 FILM 0.0015MF 5% 50V C945 1-137-372-11 FILM 0.022MF 5% 50V
C813 1-137-370-11 FILM 0.01MF 5% 50V C946 1-102-106-00 CERAMIC 100PF 10% 50V
C814 1-136-169-00 FILM 0.22MF 5% 50V C948 1-130-495-00 FILM 0.1MF 5% 50V
C815 1-137-366-11 FILM 0.0022MF 5% 50V C950 1-117-378-11 FILM 1MF 5% 50V

C817 1-126-933-11 ELECT 100MF 20% 16V C955 1-102-106-00 CERAMIC 100PF 10% 50V
C818 1-130-495-00 FILM 0.1MF 5% 50V C960 1-136-177-00 FILM 1MF 5% 50V
C819 1-136-173-00 FILM 0.47MF 5% 50V C961 1-130-495-00 FILM 0.1MF 5% 50V
C820 1-137-366-11 FILM 0.0022MF 5% 50V C962 1-130-495-00 FILM 0.1MF 5% 50V
C821 1-102-112-00 CERAMIC 330PF 10% 50V C963 1-130-495-00 FILM 0.1MF 5% 50V

C822 1-137-368-11 FILM 0.0047MF 5% 50V C967 1-102-106-00 CERAMIC 100PF 10% 50V
C901 1-130-495-00 FILM 0.1MF 5% 50V C968 1-126-960-11 ELECT 1MF 20% 50V
C902 1-137-368-11 FILM 0.0047MF 5% 50V C969 1-137-364-11 FILM 0.001MF 5% 50V
C903 1-102-951-00 CERAMIC 15PF 5% 50V C970 1-102-106-00 CERAMIC 100PF 10% 50V
C904 1-130-495-00 FILM 0.1MF 5% 50V C1801 1-102-112-00 CERAMIC 330PF 10% 50V

C905 1-130-495-00 FILM 0.1MF 5% 50V C1802 1-102-112-00 CERAMIC 330PF 10% 50V
C906 1-136-173-00 FILM 0.47MF 5% 50V C1803 1-136-169-00 FILM 0.22MF 5% 50V
C907 1-126-963-11 ELECT 4.7MF 20% 50V
C908 1-102-951-00 CERAMIC 15PF 5% 50V
C910 1-104-664-11 ELECT 47MF 20% 25V CONNECTOR

C911 1-126-768-11 ELECT 2200MF 20% 16V CN501 * 1-580-798-11 CONNECTOR PIN (DY) 6P
C912 1-126-961-11 ELECT 2.2MF 20% 50V CN503 * 1-900-801-16 CONNECTOR ASSY, 2P BOARD IN
C913 1-126-961-11 ELECT 2.2MF 20% 50V CN504 1-695-915-11 TAB (CONTACT)
C915 1-107-713-11 ELECT 4.7MF 20% 35V CN505 1-564-513-11 PLUG, CONNECTOR 10P
C916 1-126-961-11 ELECT 2.2MF 20% 50V CN508 * 1-564-514-11 PLUG, CONNECTOR 11P

C917 1-126-961-11 ELECT 2.2MF 20% 50V CN509 * 1-508-879-11 BASE POST
C918 1-126-961-11 ELECT 2.2MF 20% 50V CN511 1-564-511-11 PLUG, CONNECTOR 8P
C919 1-126-961-11 ELECT 2.2MF 20% 50V CN512 1-695-915-11 TAB (CONTACT)
C920 1-126-961-11 ELECT 2.2MF 20% 50V CN600 ¡ 1-251-227-11 INLET, AC
C921 1-126-961-11 ELECT 2.2MF 20% 50V CN601 1-691-960-11 PIN, CONNECTOR (PC BOARD) 3P

C923 1-137-370-11 FILM 0.01MF 5% 50V CN605 * 1-506-371-00 PIN, CONNECTOR 2P

C924 1-130-495-00 FILM 0.1MF 5% 50V CN610 1-695-915-11 TAB (CONTACT)
C925 1-126-934-11 ELECT 220MF 20% 16V
C926 1-137-364-11 FILM 0.001MF 5% 50V DIODE
C927 1-104-664-11 ELECT 47MF 20% 25V
D401 8-719-921-40 DIODE MTZJ-4.7C
C928 1-137-370-11 FILM 0.01MF 5% 50V D402 8-719-979-58 DIODE EGP10D
C929 1-130-495-00 FILM 0.1MF 5% 50V D403 8-719-908-03 DIODE GP08D
C930 1-126-965-11 ELECT 22MF 20% 50V D501 8-719-061-21 DIODE FMQ-G5FMS
C931 1-136-169-00 FILM 0.22MF 5% 50V D502 8-719-110-49 DIODE RD18ESB2
C932 1-130-495-00 FILM 0.1MF 5% 50V D503 8-719-911-19 DIODE 1SS119-25

— 35 —
CPD200ES
Note: Note:

D
The components identified by shading Les composants identifies per un trame et une marque
and mark ¡ are critical for safety. ¡ sont critiques pour la securite. Ne les remplacer
Replace only with part number specified. que par une piece portant le numero specifie.

[Link]. PART NO. DESCRIPTION REMARK [Link]. PART NO. DESCRIPTION REMARK

D504 8-719-051-97 DIODE 3DL41A(LC6-15) D945 8-719-911-19 DIODE 1SS119-25

D505 8-719-110-17 DIODE RD10ESB2 D946 8-719-911-19 DIODE 1SS119-25
D506 8-719-110-67 DIODE RD27ESB2
D508 8-719-975-77 DIODE SB340 FUSE

D509 8-719-979-58 DIODE EGP10D F601 ¡ 1-576-231-11 FUSE (H.B.C.) 4A/250V

D510 8-719-979-58 DIODE EGP10D
D511 ¡ 8-719-110-67 DIODE RD27ESB2 FERRITE BEAD
D515 8-719-979-58 DIODE EGP10D
D522 8-719-911-19 DIODE 1SS119-25 FB501 1-410-396-41 FERRITE 0.45UH
FB502 1-412-911-11 FERRITE
D526 8-719-018-82 DIODE RGP02-20EL-6394 FB503 1-412-911-11 FERRITE
D595 8-719-911-19 DIODE 1SS119-25 FB524 1-412-911-11 FERRITE
D596 8-719-911-19 DIODE 1SS119-25 FB525 1-412-911-11 FERRITE
D598 8-719-110-49 DIODE RD18ESB2
D601 ¡ 8-719-025-88 DIODE GBU4JL-6088 FB601 1-412-911-11 FERRITE
FB602 1-412-911-11 FERRITE
D602 8-719-970-83 DIODE HSS82 FB603 1-412-911-11 FERRITE
D603 8-719-110-49 DIODE RD18ESB2 FB604 1-412-911-11 FERRITE
D604 8-719-053-19 DIODE UF4007G23 FB605 1-412-911-11 FERRITE
D605 8-719-970-83 DIODE HSS82
D607 8-719-979-58 DIODE EGP10D FB606 1-412-911-11 FERRITE
FB607 1-412-911-11 FERRITE
D608 8-719-986-73 DIODE RB441Q FB608 ¡ 1-412-911-11 FERRITE
D609 8-719-982-03 DIODE MTZJ-3.6A FB609 ¡ 1-412-911-11 FERRITE
D614 8-719-110-08 DIODE RD8.2ESB2 FB610 ¡ 1-412-911-11 FERRITE
D650 8-719-054-72 DIODE 31DF6-FC5
D651 8-719-979-58 DIODE EGP10D FB611 ¡ 1-412-911-11 FERRITE
FB612 ¡ 1-412-911-11 FERRITE
D652 8-719-979-50 DIODE EGP30D FB613 ¡ 1-412-911-11 FERRITE
D653 8-719-979-84 DIODE EGP20DPKG23 FB614 ¡ 1-412-911-11 FERRITE
D654 8-719-051-97 DIODE 3DL41A(LC6-15) FB615 ¡ 1-412-911-11 FERRITE
D656 8-719-054-72 DIODE 31DF6-FC5
D670 8-719-911-19 DIODE 1SS119-25 FB901 1-412-911-11 FERRITE
FB902 1-412-911-11 FERRITE
D801 8-719-911-19 DIODE 1SS119-25 FB903 1-412-911-11 FERRITE
D803 8-719-911-19 DIODE 1SS119-25 FB904 1-412-911-11 FERRITE
D804 8-719-911-19 DIODE 1SS119-25 FB905 1-412-911-11 FERRITE
D903 8-719-970-83 DIODE HSS82
D906 8-719-109-89 DIODE RD5.6ESB2
TERMINAL
D907 8-719-109-89 DIODE RD5.6ESB2
D908 8-719-911-19 DIODE 1SS119-25 GT001 * 1-537-738-21 TERMINAL, EARTH
D909 8-719-109-89 DIODE RD5.6ESB2 GT002 * 1-537-738-21 TERMINAL, EARTH
D910 8-719-911-19 DIODE 1SS119-25
D913 8-719-067-04 DIODE 339VYUGW/R2 IC

D915 8-719-911-19 DIODE 1SS119-25 IC400 8-759-803-42 IC LA6500-FA

D916 8-719-911-19 DIODE 1SS119-25 IC401 8-759-980-58 IC TDA8172
D917 8-719-911-19 DIODE 1SS119-25 IC601 ¡ 8-759-399-81 IC MC44603P
D918 8-719-911-19 DIODE 1SS119-25 IC603 ¡ 8-749-014-41 IC MOC8105TVZ
D920 8-719-921-40 DIODE MTZJ-4.7C IC604 ¡ 8-759-072-98 IC TDA8138A

D921 8-719-911-19 DIODE 1SS119-25 IC652 ¡ 8-759-466-13 IC TL431ACLPRP

D922 8-719-911-19 DIODE 1SS119-25 IC801 ¡ 8-759-466-15 IC UPC6753
D923 8-719-911-19 DIODE 1SS119-25 IC901 8-759-536-91 IC ST7272N5B1/CUS
D924 8-719-911-19 DIODE 1SS119-25 IC902 ¡ 8-759-269-04 IC SN74HCT02AN
D944 8-719-911-19 DIODE 1SS119-25 IC903 8-759-165-81 IC PST600D-T

— 36 —
 CPD-200ES

D
Note: The components identified by shading
Note: Les composants identifies per un trame et une marque
and mark ¡ are critical for safety. ¡ sont critiques pour la securite. Ne les remplacer
Replace only with part number specified. que par une piece portant le numero specifie.

[Link]. PART NO. DESCRIPTION REMARK [Link]. PART NO. DESCRIPTION REMARK

IC904 ¡ 8-759-399-77 IC TDA9105 RESISTOR

COIL R401 1-249-425-11 CARBON 4.7K 5% 1/4W

R407 1-215-447-00 METAL 12K 1% 1/4W
L501 1-412-550-11 INDUCTOR 1.2MMH R408 1-249-383-11 CARBON 1.5 5% 1/4W F
L504 1-459-104-00 COIL, WITH CORE R410 1-215-859-00 METAL OXIDE 22 5% 1W F
L505 1-412-531-31 INDUCTOR 33UH R411 1-215-445-00 METAL 10K 1% 1/4W
L506 1-459-104-00 COIL, WITH CORE
L507 1-412-531-31 INDUCTOR 33UH R412 1-215-421-00 METAL 1K 1% 1/4W
R418 1-214-798-21 METAL 1.8 1% 1/2W
L513 1-409-896-11 COIL, HORIZONTAL LINEARITY R420 1-215-461-00 METAL 47K 1% 1/4W
L650 1-412-537-31 INDUCTOR 100UH R421 1-214-798-21 METAL 1.8 1% 1/2W
L651 1-412-537-31 INDUCTOR 100UH R422 1-215-866-11 METAL OXIDE 330 5% 1W F
L652 1-406-665-11 INDUCTOR 100UH
L653 1-412-537-31 INDUCTOR 100UH R423 1-215-439-00 METAL 5.6K 1% 1/4W
R424 1-215-447-00 METAL 12K 1% 1/4W
L801 1-410-645-31 INDUCTOR 100UH R425 1-215-441-00 METAL 6.8K 1% 1/4W
L900 1-410-645-31 INDUCTOR 100UH R426 1-249-383-11 CARBON 1.5 5% 1/4W F
R427 1-215-447-00 METAL 12K 1% 1/4W
FILTER
R500 1-249-405-11 CARBON 100 5% 1/4W F
LF601 ¡ 1-429-180-11 TRANSFORMER, LINE FILTER R501 1-247-863-91 CARBON 22K 5% 1/4W
R503 1-249-437-11 CARBON 47K 5% 1/4W
TRANSISTOR R504 1-215-888-00 METAL OXIDE 220 5% 2W F
R505 1-247-863-91 CARBON 22K 5% 1/4W
Q500 8-729-031-89 TRANSISTOR 2SC3941A-Q(TA)
Q501 8-729-119-76 TRANSISTOR 2SA1175-HFE R506 1-216-391-11 METAL OXIDE 1.5 5% 3W F
Q502 ¡ 8-729-043-37 TRANSISTOR IRFU214 R507 1-249-437-11 CARBON 47K 5% 1/4W
Q503 8-729-027-97 TRANSISTOR IRFI9630G-LF R508 1-216-391-11 METAL OXIDE 1.5 5% 3W F
Q504 8-729-119-78 TRANSISTOR 2SC2785-HFE R509 1-249-389-11 CARBON 4.7 5% 1/4W F
R510 1-249-389-11 CARBON 4.7 5% 1/4W
Q505 8-729-119-76 TRANSISTOR 2SA1175-HFE
Q507 8-729-030-67 TRANSISTOR 2SC5129(LBSONY1) R511 1-249-401-11 CARBON 47 5% 1/4W
Q508 ¡ 8-729-042-24 TRANSISTOR 2SB949-Q(LE) R512 1-247-881-00 CARBON 120K 5% 1/4W
Q509 ¡ 8-729-042-33 TRANSISTOR 2SD1275Q-LE R513 1-249-429-11 CARBON 10K 5% 1/4W
Q510 8-729-027-82 TRANSISTOR IRFPE40LF20 R514 1-249-429-11 CARBON 10K 5% 1/4W
4-060-503-01 SHEET, INSULATING (for Q510) R515 1-215-481-00 METAL 330K 1% 1/4W

R517 1-249-417-11 CARBON 1K 5% 1/4W F

Q512 8-729-027-14 TRANSISTOR 2SK1904 R518 1-249-417-11 CARBON 1K 5% 1/4W F
Q513 8-729-027-14 TRANSISTOR 2SK1904 R519 1-249-437-11 CARBON 47K 5% 1/4W
Q514 8-729-027-14 TRANSISTOR 2SK1904 R520 1-249-417-11 CARBON 1K 5% 1/4W F
Q515 8-729-140-50 TRANSISTOR 2SC3209LK R521 1-249-389-11 CARBON 4.7 5% 1/4W F
Q528 8-729-140-50 TRANSISTOR 2SC3209LK
R522 1-249-417-11 CARBON 1K 5% 1/4W F
Q529 8-729-028-34 TRANSISTOR 2SD1640Q,R R523 1-249-377-11 CARBON 0.47 5% 1/4W F
Q602 ¡ 8-729-926-79 TRANSISTOR IRFIBC40 R524 1-216-447-00 METAL OXIDE 27 5% 2W F
Q654 8-729-141-83 TRANSISTOR 2SB1094-LK R525 1-249-426-11 CARBON 5.6K 5% 1/4W
Q655 8-729-119-78 TRANSISTOR 2SC2785-HFE R526 1-249-377-11 CARBON 0.47 5% 1/4W F
Q656 ¡ 8-729-119-78 TRANSISTOR 2SC2785-HFE
R527 1-215-913-11 METAL OXIDE 220 5% 3W F
Q670 8-729-011-92 TRANSISTOR 2SC2001TP-K1K2 R528 1-215-910-00 METAL OXIDE 68 5% 3W F
Q901 8-729-119-78 TRANSISTOR 2SC2785-HFE R529 1-249-441-11 CARBON 100K 5% 1/4W
Q902 8-729-029-86 TRANSISTOR DTC124ESA R530 1-216-474-11 METAL OXIDE 82 5% 3W F
Q903 8-729-107-78 TRANSISTOR 2SC3623-K R531 1-216-474-11 METAL OXIDE 82 5% 3W F

R532 1-249-389-11 CARBON 4.7 5% 1/4W F

R533 ¡ 1-215-488-00 METAL 620K 1% 1/4W

— 37 —
CPD200ES
Note: Note:

D
The components identified by shading Les composants identifies per un trame et une marque
and mark ¡ are critical for safety. ¡ sont critiques pour la securite. Ne les remplacer
Replace only with part number specified. que par une piece portant le numero specifie.

[Link]. PART NO. DESCRIPTION REMARK [Link]. PART NO. DESCRIPTION REMARK

R534 ¡ 1-215-468-00 METAL 91K 1% 1/4W R652 ¡ 1-211-874-11 FUSIBLE 0.12 10% 1/2W
R535 ¡ 1-215-473-00 METAL 150K 1% 1/4W R654 ¡ 1-219-154-11 FUSIBLE 0.12 10% 1/4W
R536 1-249-428-11 CARBON 8.2K 5% 1/4W R655 1-249-417-11 CARBON 1K 5% 1/4W
R537 1-249-397-11 CARBON 22 5% 1/4W F R656 1-249-417-11 CARBON 1K 5% 1/4W
R538 1-215-441-00 METAL 6.8K 1% 1/4W
R657 1-249-429-11 CARBON 10K 5% 1/4W
R539 1-215-476-00 METAL 200K 1% 1/4W R658 1-215-417-00 METAL 680 1% 1/4W
R540 1-215-457-00 METAL 33K 1% 1/4W R659 1-215-483-00 METAL 390K 1% 1/4W
R541 1-215-443-00 METAL 8.2K 1% 1/4W R660 1-215-443-00 METAL 8.2K 1% 1/4W
R542 ¡ 1-215-429-00 METAL 2.2K 1% 1/4W R661 1-247-895-91 CARBON 470K 5% 1/4W
R543 ¡ 1-215-429-00 METAL 2.2K 1% 1/4W
R662 1-215-457-00 METAL 33K 1% 1/4W
R544 ¡ 1-215-463-00 METAL 56K 1% 1/4W R663 1-249-429-11 CARBON 10K 5% 1/4W
R545 ¡ 1-215-461-00 METAL 47K 1% 1/4W R664 1-216-352-11 METAL OXIDE 1.8 5% 1W F
R546 1-249-397-11 CARBON 22 5% 1/4W F R665 1-249-429-11 CARBON 10K 5% 1/4W
R547 1-249-424-11 CARBON 3.9K 5% 1/4W R666 1-249-429-11 CARBON 10K 5% 1/4W
R548 1-215-437-00 METAL 4.7K 1% 1/4W
R667 ¡ 1-211-881-11 FUSIBLE 0.47 10% 1/2W
R549 1-215-880-00 METAL OXIDE 10 5% 2W F R670 1-249-417-11 CARBON 1K 5% 1/4W
R550 1-249-429-11 CARBON 10K 5% 1/4W R671 1-249-417-11 CARBON 1K 5% 1/4W
R551 1-215-423-00 METAL 1.2K 1% 1/4W R672 1-249-403-11 CARBON 68 5% 1/4W
R552 1-249-385-11 CARBON 2.2 5% 1/4W F R673 1-249-429-11 CARBON 10K 5% 1/4W
R553 1-249-421-11 CARBON 2.2K 5% 1/4W
R674 1-249-429-11 CARBON 10K 5% 1/4W
R554 1-249-421-11 CARBON 2.2K 5% 1/4W R801 1-249-377-11 CARBON 0.47 5% 1/4W F
R555 1-249-377-11 CARBON 0.47 5% 1/4W F R807 1-249-438-11 CARBON 56K 5% 1/4W
R556 1-202-818-00 SOLID 1K 20% 1/2W R808 1-215-485-00 METAL 470K 1% 1/4W
R563 1-249-421-11 CARBON 2.2K 5% 1/4W R809 1-215-483-00 METAL 390K 1% 1/4W
R564 1-249-421-11 CARBON 2.2K 5% 1/4W
R811 1-249-432-11 CARBON 18K 5% 1/4W
R565 1-215-483-00 METAL 390K 1% 1/4W R815 1-215-457-00 METAL 33K 1% 1/4W
R567 1-215-880-00 METAL OXIDE 10 5% 2W F R817 1-215-461-00 METAL 47K 1% 1/4W
R598 1-215-453-00 METAL 22K 1% 1/4W R819 1-215-457-00 METAL 33K 1% 1/4W
R599 1-215-467-00 METAL 82K 1% 1/4W R820 1-215-455-00 METAL 27K 1% 1/4W
R601 ¡ 1-202-847-00 SOLID 560K 20% 1/2W
R602 ¡ 1-205-998-11 CEMENTED 1 5% 10W R821 1-215-465-00 METAL 68K 1% 1/4W
R603 ¡ 1-202-933-61 FUSIBLE 0.1 10% 1/2W F R822 1-215-471-00 METAL 120K 1% 1/4W
R604 1-215-926-00 METAL OXIDE 33K 5% 3W F R823 1-215-481-00 METAL 330K 1% 1/4W
R605 1-249-437-11 CARBON 47K 5% 1/4W R824 1-249-429-11 CARBON 10K 5% 1/4W
R606 1-249-417-11 CARBON 1K 5% 1/4W R825 1-259-878-11 CARBON 1.5M 5% 1/4W

R607 1-247-791-91 CARBON 22 5% 1/4W R830 1-215-461-00 METAL 47K 1% 1/4W

R608 1-249-429-11 CARBON 10K 5% 1/4W R831 1-215-405-00 METAL 220 1% 1/4W
R609 1-216-381-11 METAL OXIDE 0.22 5% 3W F R900 1-249-417-11 CARBON 1K 5% 1/4W
R610 1-215-925-11 METAL OXIDE 22K 5% 3W F R901 1-249-425-11 CARBON 4.7K 5% 1/4W
R611 1-247-885-00 CARBON 180K 5% 1/4W R902 1-249-425-11 CARBON 4.7K 5% 1/4W

R612 1-249-431-11 CARBON 15K 5% 1/4W R903 1-249-425-11 CARBON 4.7K 5% 1/4W
R613 1-249-411-11 CARBON 330 5% 1/4W R904 1-249-425-11 CARBON 4.7K 5% 1/4W
R614 1-249-421-11 CARBON 2.2K 5% 1/4W R905 1-249-425-11 CARBON 4.7K 5% 1/4W
R615 1-249-377-11 CARBON 0.47 5% 1/4W F R906 1-215-449-00 METAL 15K 1% 1/4W
R619 1-249-425-11 CARBON 4.7K 5% 1/4W R907 1-249-417-11 CARBON 1K 5% 1/4W

R621 1-249-434-11 CARBON 27K 5% 1/4W R908 1-249-425-11 CARBON 4.7K 5% 1/4W
R623 1-215-445-00 METAL 10K 1% 1/4W R909 1-249-437-11 CARBON 47K 5% 1/4W
R631 1-215-405-00 METAL 220 1% 1/4W R910 1-247-895-91 CARBON 470K 5% 1/4W
R651 1-215-878-00 METAL OXIDE 33K 5% 1W F R911 1-249-431-11 CARBON 15K 5% 1/4W

— 38 —
 CPD-200ES

D
Note: The components identified by shading Note: The components identified by [ in this manual have been
and mark ¡ are critical for safety. carefully factory-selected for each set in order to satisfy
Replace only with part number specified. regulations regarding X-ray radiation. Should replacement
be required, replace only with the value originally used.

[Link]. PART NO. DESCRIPTION REMARK [Link]. PART NO. DESCRIPTION REMARK

R912 1-249-413-11 CARBON 470 5% 1/4W R965 1-249-415-11 CARBON 680 5% 1/4W
R914 1-249-421-11 CARBON 2.2K 5% 1/4W R966 1-247-895-91 CARBON 470K 5% 1/4W
R915 1-249-417-11 CARBON 1K 5% 1/4W R968 1-247-883-00 CARBON 150K 5% 1/4W
R916 1-249-417-11 CARBON 1K 5% 1/4W R972 1-249-429-11 CARBON 10K 5% 1/4W
R973 1-249-429-11 CARBON 10K 5% 1/4W
R917 1-249-417-11 CARBON 1K 5% 1/4W
R918 1-249-435-11 CARBON 33K 5% 1/4W R975 1-249-429-11 CARBON 10K 5% 1/4W
R919 1-249-425-11 CARBON 4.7K 5% 1/4W R976 1-249-425-11 CARBON 4.7K 5% 1/4W
R920 1-249-417-11 CARBON 1K 5% 1/4W R977 1-249-417-11 CARBON 1K 5% 1/4W
R921 1-247-863-91 CARBON 22K 5% 1/4W R979 1-249-432-11 CARBON 18K 5% 1/4W
R980 1-247-883-00 CARBON 150K 5% 1/4W
R924 1-249-434-11 CARBON 27K 5% 1/4W
R925 1-249-432-11 CARBON 18K 5% 1/4W R981 1-249-413-11 CARBON 470 5% 1/4W
R926 1-249-434-11 CARBON 27K 5% 1/4W R983 1-215-467-00 METAL 82K 1% 1/4W
R927 1-249-434-11 CARBON 27K 5% 1/4W R984 1-249-417-11 CARBON 1K 5% 1/4W
R928 1-249-434-11 CARBON 27K 5% 1/4W R985 1-247-807-31 CARBON 100 5% 1/4W
R986 1-215-445-00 METAL 10K 1% 1/4W
R929 1-249-436-11 CARBON 39K 5% 1/4W
R930 1-249-434-11 CARBON 27K 5% 1/4W R987 1-249-425-11 CARBON 4.7K 5% 1/4W
R931 1-249-428-11 CARBON 8.2K 5% 1/4W R989 1-249-429-11 CARBON 10K 5% 1/4W
R932 1-249-428-11 CARBON 8.2K 5% 1/4W R990 1-247-807-31 CARBON 100 5% 1/4W
R933 1-249-431-11 CARBON 15K 5% 1/4W R991 1-247-807-31 CARBON 100 5% 1/4W
R992 1-249-417-11 CARBON 1K 5% 1/4W
R934 1-249-429-11 CARBON 10K 5% 1/4W
R935 1-249-428-11 CARBON 8.2K 5% 1/4W R993 1-249-429-11 CARBON 10K 5% 1/4W
R936 1-249-425-11 CARBON 4.7K 5% 1/4W R994 1-249-417-11 CARBON 1K 5% 1/4W
R937 1-249-428-11 CARBON 8.2K 5% 1/4W R995 1-249-413-11 CARBON 470 5% 1/4W
R938 1-249-428-11 CARBON 8.2K 5% 1/4W R996 1-249-429-11 CARBON 10K 5% 1/4W
R997 1-249-417-11 CARBON 1K 5% 1/4W
R939 1-249-417-11 CARBON 1K 5% 1/4W
R940 1-249-434-11 CARBON 27K 5% 1/4W R998 1-249-429-11 CARBON 10K 5% 1/4W
R941 1-249-428-11 CARBON 8.2K 5% 1/4W R999 1-249-413-11 CARBON 470 5% 1/4W
R942 1-249-434-11 CARBON 27K 5% 1/4W R1801 1-215-433-00 METAL 3.3K 1% 1/4W
R943 1-249-428-11 CARBON 8.2K 5% 1/4W R1806 1-215-421-00 METAL 1K 1% 1/4W
R1810 1-215-413-00 METAL 470 1% 1/4W
R944 1-249-424-11 CARBON 3.9K 5% 1/4W
R945 1-249-424-11 CARBON 3.9K 5% 1/4W R1811 1-215-409-00 METAL 330 1% 1/4W
R946 1-247-903-00 CARBON 1M 5% 1/4W R1812 1-215-413-00 METAL 470 1% 1/4W
R947 1-247-883-00 CARBON 150K 5% 1/4W R1813 1-215-413-00 METAL 470 1% 1/4W
R948 1-247-883-00 CARBON 150K 5% 1/4W R1814 1-215-417-00 METAL 680 1% 1/4W
R1815 1-215-469-00 METAL 100K 1% 1/4W
R949 1-247-883-00 CARBON 150K 5% 1/4W
R950 1-247-883-00 CARBON 150K 5% 1/4W R1818 1-215-425-00 METAL 1.5K 1% 1/4W
R951 1-247-883-00 CARBON 150K 5% 1/4W R1819 1-215-425-00 METAL 1.5K 1% 1/4W
R952 1-247-883-00 CARBON 150K 5% 1/4W R1820 1-215-433-00 METAL 3.3K 1% 1/4W
R954 1-249-425-11 CARBON 4.7K 5% 1/4W R1822 1-215-433-00 METAL 3.3K 1% 1/4W
R1823 1-215-413-00 METAL 470 1% 1/4W
R955 1-215-478-00 METAL 240K 1% 1/4W R1832 1-215-469-00 METAL 100K 1% 1/4W
R956 1-249-421-11 CARBON 2.2K 5% 1/4W
R957 1-215-441-00 METAL 6.8K 1% 1/4W
R958 1-249-420-11 CARBON 1.8K 5% 1/4W VARIABLE RESISTOR
R959 1-249-428-11 CARBON 8.2K 5% 1/4W
[ RV501 ¡ 1-241-767-21 RES, ADJ, CERMET 100K
R960 1-249-425-11 CARBON 4.7K 5% 1/4W 4-060-176-01 COVER, VOLUME 6 MOLD (for RV501)
R962 1-249-429-11 CARBON 10K 5% 1/4W
R963 1-249-429-11 CARBON 10K 5% 1/4W
R964 1-247-883-00 CARBON 150K 5% 1/4W

— 39 —
CPD200ES
Note: The components identified by shading
Note: Les composants identifies per un trame et une marque

D and mark ¡ are critical for safety.

Replace only with part number specified.
¡ sont critiques pour la securite. Ne les remplacer
que par une piece portant le numero specifie.

[Link]. PART NO. DESCRIPTION REMARK [Link].

[Link]. PART
PART NO.
NO. DESCRIPTION
DESCRIPTION REMARK
REMARK

RELAY MISCELLANEOUS
RY601 ¡ 1-755-031-11 RELAY ¡ 1-416-282-21 COIL, DEMAGNETIZATION
¡ 1-452-923-21 NECK ASSY (NA-2914)
SWITCH 1-543-653-11 CORE ASSY,BEAD (DIVISION TYPE)
¡ 1-783-481-11 CORD SET, POWER
S1801 1-692-431-21 SWITCH, TACTILE 4-060-206-01 DISK, WINDOWS 95
S1802 1-692-431-21 SWITCH, TACTILE 3-860-654-11 MANUAL, INSTRUCTION
S1803 1-692-431-21 SWITCH, TACTILE ¡ 8-451-487-11 DY Y17FRG-M
S1809 1-692-431-21 SWITCH, TACTILE ¡ 1-453-240-21 TRANSFORMER ASSY, FLYBACK(NX-4103//JIE4)
S1815 1-692-220-11 SWITCH, TACTILE ¡ 8-738-731-05 CRT, 17FRSM (M41LKN70X)

S1816 1-692-220-11 SWITCH, TACTILE

S1817 1-692-220-11 SWITCH, TACTILE
S1818 1-692-220-11 SWITCH, TACTILE
S1821 1-692-431-21 SWITCH, TACTILE

SPARK GAP

SG501 ¡ 1-519-422-11 GAP, SPARK

TRANSFORMER

T501 ¡ 1-453-240-21 TRANSFORMER ASSY, FLYBACK

T503 1-429-109-11 TRANSFORMER, FERRITE (DFT)
T504 ¡ 1-426-971-21 TRANSFORMER, FERRITE (HDT)
T505 1-426-998-11 TRANSFORMER, FERRITE (HST)
T601 ¡ 1-431-247-11 TRANSFORMER, CONVERTER (SRT)

THERMISTOR

TH501 1-807-796-11 THERMISTOR

TH601 ¡ 1-809-260-11 THERMISTOR, POWER
TH602 ¡ 1-809-827-11 THERMISTOR, POSITIVE

VARISTOR

VA601 ¡ 1-810-622-11 VARISTOR

CRYSTAL

X900 1-567-890-11 VIBRATOR, CRYSTAL

Sony Corporation
Sony Technology Center
English
Product Quality Division 98BJ74060-1
Printed in U.S.A.
9-978-840-01 Service Promotion Department © 1998.2
— 40 —