Marble SERIES

Garage Door Openers

USER MANUAL
 INDEX
1. Warnings 2
2. Product description 3
2.1 Applications 3
2.2 Description of the automation 3
3. Installation 4
3.1 Inventory of a garage door opener 4
3.2 Rail assembly 5
3.3 Attach the rail to the motor 6
3.4 Attach the rail on the header wall and ceiling 6
3.5 Connect release section to the garage door 7
3.6 Final steps before system learning 8
3.7 Introduction of the emergency release 8
4. Operation 9
4.1 Accessory connection 9
4.2 Door position for start-up phase 9
4.3 Transmitter memorizing and erasing process 10
4.4 System learning, reset process, and LED display 10
4.5 Programmable function indication LED 12
4.6 How to set the parameter 12
4.7 Programmable function setting 13
5. Function of terminals 14
5.1 Photocells 14
5.2 Installation of Photocells 14
6. Specification 15
7. Wi-Fi Box User Manual 16
8. Accessory 17

1. WARNINGS
WARNING :
Please read this instruction manual carefully before the installation.
This manual is exclusively for qualified installation personnel. TMT Automation Inc. is not responsible for
improper installation and failure to comply with local electrical and building regulations.
Keep all the components for the garage door opener and this manual in hand for further consultation.

● In this manual, please pay extra attention to the contents marked by the symbol:
● Be aware of the hazards that may exist in the procedures of installation and operation of the garage door opener.
Besides, the installation must be carried out inconformity with local standards and regulations.
● If the system is correctly installed and followed all the regulations, it will ensure a high degree of security.
● Make sure that the door works properly before installing the garage door opener and confirm the doors are
appropriate for the application.
● Do not let children operate or play with the garage door opener.
● Do not cross the path of the garage door opener when it is in operation.
● Please keep all the control devices and any other pulse generator away from children to avoid the system being
activated accidentally.
● Do not make any modifications to any components except that it is mentioned in this manual.
● Do not try to manually open or close the doors before you release the opener.
● If there is a failure that cannot be solved and is not mentioned in this manual, please contact a professional installer.
● Do not use the garage door opener before all the procedures and instructions have been carried out and
thoroughly read.
● Install warning signs (if necessary) on the both sides of the door to warn the people in the area of potential hazards.

GARAGE DOOR OPENERS USER MANUAL 2

2. PRODUCT DESCRIPTION

2.1 APPLICATIONS
Garage door opener is applied for residential automation of up and over doors and sectional doors. It has to be operat-
ed with electricity. It’s forbidden to be operated by back-up batteries for normal [Link]-up batteries are only allowed
for emergent operation when there is a power failure, and the carriage can be released by pulling the cord to move the
door manually.

2.2 DESCRIPTION OF THE AUTOMATION

1). The following diagram of typical installation describes some terms and accessory of the door automation
system:

4
1

3
1 Garage Door Opener
5
2 Photocells (Optional accessories)
3 Flashing Light (Optional accessories)
2 2 4 Key selector (Optional accessories)
6
5 Push Button (Optional accessories)
6 Transmitter

2). The indication of control panel

1 Operation buttons: Remote Function key (RF),

1
Setting key (Set), UP key (Up), DOWN key (Down).
2 Connection terminal of Optional accessories
3 Radio receiver board
2
5 4 Fuse
3 4 5 Wi-Fi Box

EXT- EXT+ LIT- LIT+ PB GND PH +24V GND +BATT

3). The LED indication

1 The power indicator is on the bottom right of the display. When the motor
is powered, the LED dot indicator is alight.
2 When entering to the power-saving mode, the LED power indicator is
flashing ( light for 0.5 second and then no light for 5 seconds )

3 GARAGE DOOR OPENERS USER MANUAL

3. Installation

3.1 Inventory of a garage door opener

1 2 3 4 5 6 7

C Rail Front hold Rear Pulley Support Front Pulley Release Rope
Tensioner

8 9 10 11 12 13 14 15

Header bracket Door Bracket Ceiling Bracket

Bracket Bracket Bent Arm Straight Arm

16
Hardware Inventory
17

Door Bracket Locator Ceiling Support Bracket

18 19 20 21 22
Blocker x1 Locking x2 Screws x4 M8*20 M6*14
Optional for 1pcs x 1M Rail Plate HEX bolt x4 HEX bolt x4

28 26 Long Clevis Pin

23 24 25
Junction x2 Clevis Pin x2 M8*8 Nut x4 M6*6 Nut x8 27 Cotter Pin

GARAGE DOOR OPENERS USER MANUAL 4

3.2 Rail assembly

Assemble the front and middle rail with the

1 junction, and make sure it is located at the middle
of the protruding point.
28

2 Assemble the back and middle rail with another junction,

and make sure it is located at the middle of the
protruding point.
28

1. The (6) Inner trolly assy and the (5) Chain and index are already in the Rail. 18
3 2. Make sure the metal index is on right side of the rail. 8
3. Fasten the (8) Outer trolly assy on the (6) Inner trolly assy with (18) Screws 4pcs

6 5
Inner trolly assy Chain and index

4
Remove the nut and the spring in the (4) Front pulley tensioner. Make sure the metal chain is placed in the gap of the
pulley on the two sides. Insert the (2) Front hold bracket against the rail. Use the spring and the nut to adjust the
tightness of the (5) Chain.
2
Completion

4
5

Note: Remember to lubricate the front and rear pulley before use.

5 GARAGE DOOR OPENERS USER MANUAL

 3.3 Attach the rail to the motor
1. Connect the (3) Rear pulley support to the output shaft of the motor.
2. Fasten the rail on the motor with (9) Motor hold bracket and the (25) Hex nuts.
3. Fasten the (10) Ceiling hold bracket and (13) Ceiling bracket at the rear side between the motor
and the rear blocker with Hex bolt (21) and Hex nuts (24).
Remark: Optional choice is to use L-bracket to hold the brackets to the ceiling, and fasten to
both the ceiling and ceiling bracket(13) using Hex bolt(22) and Hex nuts(25).
21
HEX bolt

1 2 3
25 Nut
13
Ceiling
bracket
9 Motor
hold bracket

10 Ceiling 24
hold bracket Nut

3.4 Attach the rail on the header wall and ceiling

1. Position (11) Header bracket on the header wall.
* It is recommended to align the (11) Header bracket with the horizontal center of the door
*It is recommended to position the (11) Header bracket at a height 30-50cm from the top of the door.
2. Install the (11) Header bracket with screws.
3. Attach the front rail to header bracket with bolts.
4. Attach the (13) Ceiling bracket on the crossbeam of ceiling with crews.

Attach Rail to the Header Bracket

CAUTION
(11)
Header Bracket To prevent damage, place the garage door on the top
(11) section to create a temporary support.
Header
Bracket

These are not

included in the Rail
hardware inventory

2x4 is used to determine

Cotter Pin Door the correct mounting height
from ceiling.

Long Clevis
Pin

Garage
Door

GARAGE DOOR OPENERS USER MANUAL 6

3.5 Connect release section to the garage door

1
Connect the (7) Emergency release rope on the
(8) Outer trolley assy
WARNING
To prevent possible SERIOUS INJURY or DEATH from a falling
ENGAGED Secure handle with overhand knot garage door:
and heat seal rope.
• If possible, use emergency release handle to disengage trolley ONLY
when garage door is CLOSED. Weak or broken springs or
unbalanced door could result in an open door falling rapidly and/or
unexpectedly.
Rope • NEVER use emergency release handle unless garage doorway is
RELEASED
7 Emergency clear of persons and obstructions.
Release Handle Overhand • NEVER use handle to pull door open or closed. If rope knot
Knot becomes untied, you could fall.

NOTE: Handle should hang 6 feet (1.5 m) above floor.

Ensure that the rope and handle clear the tops of all
vehicles to avoid entanglement.
50cm

CONNECT DOOR ARM TO TROLLEY

2 Pull the (7) Release rope to disengage the 3 Connect (15) Straight door arm to Release trolley
(8) trolley

Pull Down
to Release
23
Trolley Clevis Pin

19
Locking Plate
15
Straight
Arm

Fasten the (12) Door bracket and (16) Door bracket locator Connect the (14) Curved arm and
4 on the center of the garage door. Connect (14) Curved arm 5 the (15) straight arm with bolts and nuts.
to (12) Door bracket.

(12)+(16)

15
Straight
Arm
19
Locking Plate

23
Clevis Pin 21
(not included in the hardware inventory)
24
Hex Bolt Nut

Connect Curved
Arm to Door Bracket

14
Curved
Door bracket locator Arm
is used when door
panel is required

7 GARAGE DOOR OPENERS USER MANUAL

 3.6 Final steps before the system learning
1. Install the (18) Blocker at the door open position.
2. Attach the warning sign to the (7) Emergency release rope.
3. Connect the power to the motor. Ensure the electric plug and socket are well connected.

1 2 3 WARNING
18
Blocker
To prevent possible SERIOUS INJURY or DEATH from
electrocution or fire:
• Ensure power is not connected to the opener, and
disconnect power from the circuit BEFORE removing
cover to establish permanent wiring connection.
RED • Garage door installation and wiring ARE in
RELEASE
CORO compliance with all local electrical and building codes.
• NEVER use an extension cord, 2-wire adapter, or
RED EMERGENCY
RELEASE KNOB
change plug in ANY way to make it fit an outlet.
Ensure the opener is grounded.

3.7 Introduction of the emergency release

1. Pull the (7) Emergency release rope to release the trolley. Make sure the trolley is disengaged. The garage door can be
operated manually.
2. Before restarting the motor, manually move the garage door until the trolley is engaged.

Pull Down
to Release
Trolley

GARAGE DOOR OPENERS USER MANUAL 8

4. Connection

4.1 Accessory connection

Only establish electrical connections when the electricity supply to the system is OFF.

A. Open the cover in order to access the electronic connection terminal of the garage gate opener.

B. Connect the wires of each accessory to the terminal.

4
TX1
EXT- EXT+ LIT- LIT+ PB GND PH +24V GND +BATT

RX1
1 2 3 5 6
External Device Flashing Light Push Button Photocell Battery

C. Function of external push button:

Door operation when pressing the push button: open-stop-close-stop

EXT- EXT+ LIT- LIT+ PB GND PH +24V GND +BATT

4.2 Door position for start-up phase

1. Use a commercial adaptor if the plug on the Marble Series unit does not correspond to the socket
[Link] the system is powered up, check if the LED is ON.

2. Never cut or remove the cable supplied with the Marble Series garage opener. The power socket of Marble garage opener
connection must be fitted by skilled and qualified personnel in strict observance of current legislation,
standards and regulations.

3. The power supply line must be protected from short circuits and ground leakage.

4. The garage door is recommeded to be set at half travel.

This will ensure the leaf is free to move both during opening and closure.

9 GARAGE DOOR OPENERS USER MANUAL

 4.3 Transmitter memorizing and erasing process
A. Transmitter Memorizing:
Press “RF Learn” button for 3 seconds, and the LED display will show “CS”; then press the transmitter A
button within 10 seconds; “CS” will blink three times and stay ON After 10 seconds without any movement,
“CS” will disappear The transmitter learning is completed.

A B

Within 10 sec
3 SEC

B. Erasing Transmitter Memory:

Press and hold "RF Learn" button for 10 seconds, the display will show “CS”. When “CC” is displayed, the memory is cleared.

10 SEC

C. Memorizing an additional transmitter by a memorized one:

Press and hold A and B buttons for 5 seconds, LED light and external flash light will blink at the same time. Within 10 seconds, press
any button on the un-memorized transmitter for 2 seconds, the transmitter will be memorized after LED light and external flash light
are off. To program by memorized transmitter, just can do the transmitter learning one by one.

A B A B
Memorized
Within 10 sec
Transmitter

4.4 System learning, reset process, and LED display

A. System Learning:
Step1: Press and hold “RF” and “SET” buttons for 3 seconds, the LED display shows “OL” and the motor enters the system
learning program.
Step2: Set the open limit and LED shows “OL”. Press and hold “UP” or “DOWN” button to adjust the door. When the door is
at the proper open position, press “SET” button.
Step3: Set the close limit and LED shows “CL”. Press and hold “UP” or “DOWN” button to adjust the door. When the door
is at the proper close position, press “SET” button.
Step4: When the LED shows “GE”. Press “SET” button to proceed operation testing. The LED will show the operation
current value in the process and memorize overcurrent value.
Step5: The motor opens and closes automatically with full speed. The LED shows “SO” while the system learning is
completed. Otherwise, the LED will show “SF" when the system learning is failed. The LED will be off after 10
seconds.
Note: The overcurrent function and flashing light function will be activated automatically after the learning process is
completed.

GARAGE DOOR OPENERS USER MANUAL 10

 3 SEC

Step.1 Step.2

Step.3 Step.4

Step.5

B. Return to the Default Setting:

Press “RF” and “DOWN” buttons for 3 seconds, and the whole setting will be defaulted when the LED shows “CL”.

Default Setting

3 SEC

C. Motor current auto-detection

The LED shows the current consumption of the motor

During the system learning process, the control panel will automatically detect the
current consumption from each motor, indicate the resistance level of the gate
whiling the motor operation. If this reading increase instantly or stay in high
reading, please DO check if any object is in between the gate moving area, and
contact your installer for further inspection.

11 GARAGE DOOR OPENERS USER MANUAL

4.5 Programmable function indication LED
LED Display Programmable Functions LED Display Programmable Functions
Start transmitter learning mode. Operation testing

Cleaned all studied transmitter. System Learning Fail.

Set up Open Limit. System Learning Completely.

Set up Close Limit. System setting clear

4.6 How to set the parameter:

Step 1: Press the“Set” key for 3 seconds, the LED will show the function code.
Step 2: Choosing the function by “Up” or “Down” keys. Press the “Set” key to enter the setting of parameters. Please
refer to the following sections for further details of the function setting

3 SEC

Confirm

Confirm

GARAGE DOOR OPENERS USER MANUAL 12

4.7 Programmable function setting
LED Display Definition Function Value Description
1 Deceleration Point 1-1 75% [Link] default setting is "1-3"

(% full operation) 1-2 80%

1-3 85%
1-4 90%
1-5 95%
2 Main Operation Key 2-0 Function off [Link] default setting is "2-1"

2-1 A Key
2-2 B Key
2-3 C Key
2-4 D Key
3 3-0 Function off [Link] default setting is "3-2"

Lighting Key 3-1 A Key

3-2 B Key
3-3 C Key
3-4 D Key
4 External Device Key 4-0 Function off [Link] default setting is "4-3"

4-1 A Key
4-2 B Key
4-3 C Key
4-4 D Key
5 Photocell Function Mode 5-0 Function off [Link] default setting is "5-0 "

PH Terminal 5-1 Mode 1 2. Please refer to page 14_Function of photocells

5-2 Mode 2

6 Alarm Buzzer 6-1 Function off [Link] default setting is "6-1"

6-2 Function on 2. IF the door left opened for longer than 10mins then buzzer

start beeping and turn off until the door been closed.

7 Auto-closing 7-1 Function off [Link] default setting is "7-1"

7-2 30 sec
7-3 60 sec
7-4 90 sec
7-5 120 sec
7-6 150 sec
7-7 180 sec
7-8 210 sec
7-9 240 sec
8 Lighting 8-1 Function off [Link] default setting is "8-4"

8-2 LED light starts running 1 minute

8-3 LED light starts running 2 minutes
8-4 LED light starts running 3 minutes
9 Overcurrent reaction 9-1 Stop when over-current [Link] default setting is "9-2"

9-2 Reverse 2 seconds when over-current

9-3 Reverse to the end when over-current
A Overcurrent setting 1-0 Learning current add 0.2A as overcurrent 1. The default setting is "3-0"

2-0 Learning current add 0.4A as overcurrent

3-0 Learning current add 0.5A as overcurrent
4-0 Learning current add 0.6A as overcurrent
5-0 Learning current add 0.8A as overcurrent
6-0 Learning current add 1.0A as overcurrent
7-0 Learning current add 1.2A as overcurrent
8-0 Learning current add 1.4A as overcurrent
9-0 Learning current add 1.6A as overcurrent
9-9 Learning current add 1.8A as overcurrent

13 GARAGE DOOR OPENERS USER MANUAL

LED Display Definition Function Value Description
C Overcurrent setting of open C1 2A as overcurrent value of open limit 1. The default setting is "C-3"
limit C2 3A as overcurrent value of open limit
C3 4A as overcurrent value of open limit
C4 5A as overcurrent value of open limit
C5 6A as overcurrent value of open limit
C6 7A as overcurrent value of open limit
C7 8A as overcurrent value of open limit
E Overcurrent setting of close E1 2A as overcurrent value of close limit 1. The default setting is "E-3"
limit E2 3A as overcurrent value of close limit
E3 4A as overcurrent value of close limit
E4 5A as overcurrent value of close limit
E5 6A as overcurrent value of close limit
E6 7A as overcurrent value of close limit
E7 8A as overcurrent value of close limit
F Power supply for +24V F1 Continuously power supply 1. The default setting is "F-1"
terminal F2 Sleep mode 2. Sleep mode: Power supply only when motor is
operating

5. Function of external accessory

5.1 Photocells
F5-1 Mode 1
Gate Status The reactions of the photocells when obstacles are detected
Closed No effect
Opened 1. Stop till next command is given
2. Stop and reload the auto-closing time if the auto-closing feature is on
Stop during moving 1. Stop till next command is given
2. Stop and reload the auto-closing time if the auto-closing feature is on
Closing Stop till next command is given
Opening Stop till next command is given

F5-2 Mode 2
Gate Status The reactions of the photocells when obstacles are detected
Closed No effect
Opened 1. Stop till next command is given
2. Stop and reload the auto-closing time if the auto-closing feature is on
Stop during moving 1. Not allow to close till next command is given
2. Not allow to close and reload the auto-closing time if the auto-closing feature is on
Closing Stop till next command is given
Opening No effect

GARAGE DOOR OPENERS USER MANUAL 14

 5.2 Installation of Photocells

The safety photocells are security devices to control automatic gates. It’s consist of one transmitter and one
receiver set in the waterproof covers. It will be triggered when the path of the beam is blocked.

SPECIFICATION:
Detection Method Through Beam
Sensing Range MAX~15m
Input Voltage AC/DC 12~24V
Contact Current TX: 30mA Max , RX: 25 mA Max
Response Time <100mS
Emitting Element Infrared LED/ Wave Length 940nm
Operation Indicator RXRed LED On (beam broken) / Off (beam aligned)
TXRed LED On
Dimensions 63*63*30 mm
Output Method Relay Output
Current Consumption Beam aligned RX<25ma\TX<30ma
Beam broken RX <10ma\TX <30ma
Connection Method Terminal Block
Housing Material ABS / PC
Water Proof IP54
Safety Standard CE

RX TX
Power LED
Indicator

Lens
EXT-
LIT- EXT+
LIT+ PB GND PH +24V GND +BATT

Terminal Block
+ - NO NC COM + -

1 2 3 4 5
Power 1 2

Terminal Block

INSTALLATION:
1. Open the cover and connect the wires.
2. Mount the receiver and transmitter on the proper position.
3. Ensure there are no obstacles between receiver and transmitter.
For optimal efficiency, the receiver and transmitter should be properly aligned.
4. Power-up the photocells and make sure the LED light on receiver and transmitter are ON.

Step 1 Step 2 Step 3 Step 4

15 GARAGE DOOR OPENERS USER MANUAL

6. Specification

Garage Door Opener MARBLE60 MARBLE80 MARBLE100 MARBLE120

Volt AC 220V / 110V ; AC 220V / 110V ; AC 220V / 110V ; AC 220V / 110V ;
50Hz~60Hz 50Hz~60Hz 50Hz~60Hz 50Hz~60Hz
Motor volt DC24V DC24V DC24V DC24V
Power 72W 80W 100W 120W
Force 600N 800N 1000N 1200N
Remote frequency 433.92MHZ 433.92MHZ 433.92MHZ 433.92MHZ
Max door area 8-10m² 10-12m² 12-14m² 14-16m²
Temperature range -20 C ~ +50oC
o
-20 C ~ +50oC
o
-20 C ~ +50oC
o
-20 C ~ +50oC
o

Rail length 3.0m/3.3m 3.0m/3.3m 3.0m/3.3m 3.0m/3.3m

Running speed 140mm/sec 140mm/sec 140mm/sec 140mm/sec

[Link] Online User Manual

Marble
User Manual

[Link]/marble_manual_en

GARAGE DOOR OPENERS USER MANUAL 16

8. Accessories

TM3 Transmitter
Frequency 433.92Mhz
Coding Rolling code
Buttons 4 buttons
Power Supply 3V with one CR2032 button type lithium battery
Operating Temperature -20°C~+50°C
Dimension 37*67.5*12 (mm)

FL2 Flashing Light

Voltage 24V DC
Operating Temperature -20°C~+50°C
Installation Horizontally or vertically installed
Dimension 74*167*58.4 (mm)

H2 Photocells
Detection type Through beam
Operating distance MAX~15 meters
Response time <100mS
Input voltage AC/DC 12-24V
Operating Temperature -20°C~+50°C
Protection level IP54
Dimension 63*63*30 (mm)

K1 Key Selector
Operating Temperature -20°C~+50°C
Dimension 73.2*73.2*42.3 (mm)

P1 Keypad
Frequency 433.92Mhz
Coding Rolling code
Power Supply 12 ~ 24V DC/AC
Operating Temperature -20°C~+50°C
Dimension 106*53*20 (mm)

RB1 Receiver Box

Frequency 433.92Mhz
Coding Rolling code
Power Supply 12 ~ 24V DC/AC
Operating Temperature -20°C~+50°C
Dimension 106*53*20 (mm)

17 GARAGE DOOR OPENERS USER MANUAL

GARAGE DOOR OPENERS USER MANUAL 18
19 GARAGE DOOR OPENERS USER MANUAL
34100-196-05-B