B-3-3.
4 BSL™ Model for Miniature Lathes
1. Features (3) Allowable d·n value and the criterion of 4. Lineup
A Prompt delivery maximum rotational speed The BSL model is available in the following varieties:
Screw shaft configuration and ball nut shape are The allowable d·n value and criterion of
Table 2 BSL model lineup
standardized for prompt delivery. maximum rotational speed are shown below.
A High speed and low noise Please consult NSK if the rotational speed Nut Shape Flange shape Preload
Adoption of end-deflector recirculation system exceeds the permissible range below.
realizeds high-speed operation with low noise. Allowable d·n value: 180 000 or less
P-Preload
A Excellent dust resistance Criterion of maximum rotational speed BSL Circular 3
(Slight preload)
Thin plastic seal and specially designed ball : 4 000 min-1
grooves prevent the entry of foreign matters. Note: Please also review the critical speed.
See "Technical Description: Permissible
2. Specifications Rotational Speed" (page B47) for details.
5. Structure of model number and reference number
(1) Ball recirculation system
The following explains the codes used in model numbers and ball screw reference numbers.
End-deflector recirculation systems offer high- (4) Options
speed, low-noise operation and a compact ball The optional NSK K1 lubrication unit, molded
eModel number
nut. The structure of the recirculation system is from resin and saturated with lubrication oil,
shown in Fig.1. supplies fresh oil onto ball rolling surfaces, BSL 20 ——
———— ——
05
ensuring long-term, maintenance-free operation.
Nut: BSL Lead (mm)
Please consult NSK when using NSK K1.
Screw shaft diameter (mm)
BSL
Nut
Ball recirculation hole
End deflector
3. Design Precautions
When designing the screw shaft end, one end of eReference number for ball screws
the shaft must meet either one of the following
conditions. If not, we cannot install the ball nut W 20 05 - ——
—— —— ——
** P
— —
SS
— —
——
- C5 Z
— ——— —
——
5—
on the screw shaft. Product code Lead (mm)
• Cut the ball groove through to the shaft end. Screw shaft diameter (mm) Axial play code: Z (page B20)
Ball screw shaft • The diameters of bearing journals and the
Effective threaded length (in 100 mm units) Accuracy grade: C5 (page B37 to B42)
gear or pulley seat must be less than the root
NSK design serial number End-deflector recirculation system
Fig. 1 Structure of end-deflector recirculation system diameter of ball groove d r specified in the
Preload code: P; P-preload (page B5)
dimension tables.
(2) Accuracy grade and axial play Special bearings which have higher-load
The available standard accuracy grades and carrying capacity are available.
axial play are as follows. Please consult NSK for For general precautions regarding ball screws, 6. Handling Precautions
other grades. refer to "Design Precautions" (page B83) and Maximum operating temperature: 80°C
"Handling Precautions" (page B103). If using NSK K1, operating temperature should
Table 1 Accuracy grade and axial play
not exceed 50°C. Refer to "Design Precautions"
Accuracy grade C5
(page B83).
Axial play 0 mm (preloaded)
B515 B516
Ball Screws: BSL Model for Small Lathes
K
4-jX drill thru 30° Thin plastic seals
30° N
jY c'bore, Z depth (both ends)
jd 1 h5
jD g6
jF
jd 3 h6
jd 2 h6
jd
jd
W
PCD
jA
jd 4
M
+0.14
L7 L6 Min. L 4 L10 0
15 15 L9
+0.1
30° T 0
30° (L3) (L2) Min. L 5 Max. L 1 (L8)
M6×1 B
H L Max. L
(oil hole)
Unit: mm
Basic load ratings (N) Ball nut dimensions Shaft configuration/dimensions and reccomended bearing (reference)
Shaft Lead Root Dynamic Static External
K dimensions Bolt hole dimensions Oil hole Shaft dimensions Specialized bearing N Basic Permissible
dia. dia. N dynamic axial load
Model No. load
Bearing
jd 1 h5
rating
BSL
L L1 L4 L5 designation
jF
d l dr Ca C0a D A H B L W X Y Z T d1 d2 d3 d4 (max.) (max.) L2 L3 (min.) (min.) L6 L7 L8 L9 L10 K M F Ca (N)
jd 3 h6
jd 2 h6
jd
0
BSL2005 5 17.2 10 500 16 200 36 63 38
jd
37 49 6.5 -0.11 3 20
20 12 6.6 11 6.5 15 12 15 14.3 500 500 66 20 8 9 14 10.15 1.15 17 M15×1.0 15TAC47C 47 21 900 26 600
BSL2006 6 16.4 14 000 20 000 40 65 42 45 51 6.7 4 21
BSL2505 5 22.2 11 700 20 400 40 65 42 38 51 7.1 3 27
0
BSL2506 6 21.4 15 700 25 400 43 69 45 44 55 6.3 -0.21 4 28
25 12 6.6 11 6.5 20 15 20 19 700 700 71 27 10 14 19 15.35 1.35 22 M20×1.0 20TAC62C 62 28 500 40 500
jd 4
BSL2508 M
8 20.5 20 100 29 900 46 72 48 55 58 6.5 5 29
+0.14
L7 L6 Min. L 4 L10 0
BSL2510 10 20.5 20 000 29 800 46 72 48 65 58 6 5 29
15 15 L9
+0.1
0
0
BSL3210 103)
(L 32 (L
5002)
51 800Min. L 5 68
Max. L (L8) -0.21 6 33
32 26.4 61 93 63 18 1
76 9 14 8.5 10 25 20 25 23.9 1 000 800 71 33 12 15 20 16.35 1.35 27 M25×1.5 25TAC62C 62 28 500 40 500
BSL3212 12 32 400 51 600 Max. L 77 7 34
Notes: 1. Right-turn screws are standard. Please contact NSK for left-turn screws. 3. Shaft length L1 and shaft total length L are maximum lengths.
2. Recommended shaft configurations are provided for reference. When L is the same length as L1, the thread becomes an all screw specification.
B517 B518
