STEEL BEAM ANALYSIS & DESIGN (EN1993-1-1:2005)

In accordance with EN1993-1-1:2005 incorporating Corrigenda February 2006 and April 2009 and the UK
national annex
TEDDS calculation version 3.0.14

Dead Variable
-0.2
0.2-0.2
0.8-0.7
0.20
32.2
1.7
0.5
32.2
1.7
0.5

RHS 50x30x2.5 (Tata Steel (old))

2.5
50

30
1.00
1.00
1.10

1.000
1.000
1.000
1.000

0.92

42.5

22.5

Section is class 1

45
1.000

0.8
230
36.5

0.2
1.6

5.6
0.21
(Library item – Steel beam design title)Library item: Show beam analysis drawingLibrary item: Show
beam analysis drawingLibrary item: Show beam analysis drawingLibrary item: Show beam analysis
drawingLibrary item: Show beam analysis drawingLibrary item: Show beam analysis drawingLibrary
item: Show beam analysis drawingLibrary item: Show beam analysis drawingSupport conditionsSupport
A Vertically restrained Rotationally
restrainedSupport B Vertically restrained Rotationally
restrainedApplied loadingBeam loads Dead point load 1.695 kN at 0 mm Variable point
load 1 kN at 500 mm Dead point load 1.695 kN at 1000 mmLoad
combinationsLoad combination 1 Support A Dead ´ 1.00
Variable ´ 1.00 Dead ´ 1.00
Variable ´ 1.00 Support B Dead ´ 1.00
Variable ´ 1.00Load combination 2 Support A Dead ´ 1.35
Variable ´ 1.50 Dead ´ 1.35
Variable ´ 1.50 Support B Dead ´ 1.35
Variable ´ 1.50Analysis resultsMaximum moment; Mmax = kNm; Mmin =
kNmMaximum shear; Vmax = kN; Vmin = kNDeflection;
dmax = mm; dmin = mmMaximum reaction at support A; RA_ma
x = kN; RA_min = kNUnfactored dead load reaction at support
A; RA_Dead = kNUnfactored variable load reaction at
support A; RA_Variable = kNMaximum reaction at support B;
RB_max = kN; RB_min = kNUnfactored dead load reaction at support
B; RB_Dead = kNUnfactored variable load reaction at
support B; RB_Variable = kNSection detailsSection type; Steel
grade; Nominal thickness of element; t = mmNominal yield
strength; fy = N/mm2Nominal ultimate tensile strength; fu =
N/mm2Modulus of elasticity; E = N/mm2Library item: Section details outputLibrary
item: Show beam section sketchPartial factors - Section 6.1Resistance of cross-sections; gM0 =
Resistance of members to instability; gM1 = Resistance of tensile members to fracture;
gM2 = Library item: Partial factorsLateral restraintLibrary item: Lateral restraint header Span 1 has full
lateral restraintLibrary item: Lateral restraint outputEffective length factorsEffective length factor in
major axis; Ky = Effective length factor in minor axis; Kz =
Effective length factor for torsion; KLT.A = ;Library item: Effective length factor output
KLT.B = ;Library item: Eff length factor x1 outputClassification of cross sections - Section 5.5 e=
[235 N/mm2 / fy] = Library item: Classification headingInternal compression parts subject to bending -
Table 5.2 (sheet 1 of 3)Width of section; c = h - 3 ´ t = mm c / t = 18.4 ´ e <= 72 ´ e;
Class 1Library item: Internal bend class outputInternal compression parts subject to compression only -
Table 5.2 (sheet 1 of 3)Width of section; c = b - 3 ´ t = mm c / t = 9.7 ´ e <= 33 ´ e ;
Class 1Library item: Internal comp class outputLibrary item: Classification resultCheck shear - Section
6.2.6Library item: Design shear headerHeight of web; hw = h - 2 ´ t =
mmShear area factor; h= hw / t < 72 ´ e /
hLibrary item: Shear slenderness outputShear buckling resistance can be ignoredLibrary item: General
results outputDesign shear force; VEd = max(abs(Vmax), abs(Vmin)) = kNShear area - cl
6.2.6(3); Av = A ´ h / (b + h) = mm2Design shear resistance - cl
6.2.6(2); Vc,Rd = Vpl,Rd = Av ´ (fy / Ö[3]) / gM0 = kNLibrary item:
Shear resistance plastic outputPASS - Design shear resistance exceeds design shear forceLibrary item:
General results outputCheck bending moment major (y-y) axis - Section 6.2.5Design bending moment;
MEd = max(abs(Ms1_max), abs(Ms1_min)) = kNmLibrary item: Design bending headerDesign bending
resistance moment - eq 6.13; Mc,Rd = Mpl,Rd = Wpl.y ´ fy / gM0 = kNmLibrary item:
Design bending moment outputPASS - Design bending resistance moment exceeds design bending
momentLibrary item: General results outputCheck vertical deflection - Section 7.2.1Consider deflection
due to dead and variable loadsLimiting deflection;; dlim = Ls1 / 180 =
mmMaximum deflection span 1; d = max(abs(dmax), abs(dmin)) = mmLibrary item:
Deflection outputPASS - Maximum deflection does not exceed deflection limitLibrary item: General
results output