ML7420A/ML7425A,B
Electric Linear Valve Actuator
SPECIFICATION DATA
FEATURES
• Easy and quick installation
• No separate linkage required
• No adjustments
• Low power consumption
ML7420 • Force limiting end switches
• Spring return models
• Manual operator
• 0 to 10Vdc or 2 to 10Vdc signal input
• Position feedback signal
• Synchronous motor
• Direct / reverse action
• Stroke position on signal failure selectable
ML7425 • Corrosion resistant design
• Maintenance free
SPECIFICATIONS
Temperature Limits
GENERAL Ambient operating limits -10 to +50°C @ 5 to 95%rh
The ML7420A / ML7425A,B actuators are for modulating Ambient storage limits -40 to +70°C @ 5 to 95%rh
control with controls providing an analog output of Medium valve
0 to 10Vdc or 2 to 10Vdc. They operate Honeywell’s standard temperature Max. 150°C
valves in heating, ventilation and air conditioning (HVAC) Signals
applications. The direction of movement is reversible by
means of an internal selector plug. Signal input voltage y = 0 to 10Vdc or 2 to10Vdc
Ri = 100kΩ
Signal source output
resistance 1kΩ max.
Position feedback signal x = 2 to 10Vdc
Load 1mA max.
Safety
Protection class II in acc. with EN60730-1
Protection standard IP54 in acc. with EN60529
Flame retardant
housing V0 in acc. with UL94
(with metal cable gland)
This product meets the requirements of
CE
EN0B-0624GE02 R0399
ML7420A/ML7425A,B
Wiring Weight
2
Wiring terminals 1.5mm non spring return type 1.3kg
Cable entry PG13.5. Two additional knock spring return type 2.4kg
outs PG11 and PG13.5 for Material
auxiliary switch and
potentiometer accessories Cover ABS-FR
Base glass fibre reinforced plastic
Yoke aluminium diecast
Model Number ML7420A3006 ML7420A3014 ML7425A3005 ML7425B3004
Supply Voltage 24Vac +/-15% 50/60Hz
Power Consumption 5VA 7VA 12VA
Signal Input 0(2)Vdc Actuator stem retracted. Two way valve:”open”, three way valve port A-AB:”closed” *
Signal Input 10Vdc Actuator stem extended. Two way valve:”closed”, Three way valve port A-AB:”open” *
Stroke 20mm
Run Time @ 50Hz 1min 0.5min 1.8min
Close-off Force ≥ 600N
Spring Return Time ≈12s
Actuator stem extends Actuator stem retracts
Spring Return Direction
at power failure at power failure
* Factory setting; can be reversed by action selector plug W3
OPERATION
General Electrical Installation
The drive of a synchronous motor is converted into linear The actuators are delivered with a pre-installed cable gland
motion of the actuator stem by using a spur gear PG13.5 and two additional knock outs for PG11 and PG13.5.
transmission. The actuator stem is connected with the valve Cable length/diameter for field mounting:
• Max. 200m/1.5mm or
stem by a button keyed retainer connection. 2
2
An integrated spring package limits the stem force to a 100m/1.5mm (ML7420A3014)
factory adjusted value in either direction.
Installed microswitches switch off the actuator precisely NOTE
CAUTION
when the specified stem force is reached.
To avoid malfunction it is necessary to connect 24Vac
Manual Operation power and ground (see Fig. 2).
Actuators without spring return are equipped with a manual
operator used in case of power failure. Manual operation is NOTE
CAUTION
only possible after the power supply is switched off or
disconnected.
In case of replacement please note that the override
To operate push the manual operator knob down and turn switch has been changed (see Fig. 2).
clockwise to move the stem downward and counter-clockwise
to move the stem upward. If the actuator returns to automatic
control, the manual operator knob unlocks automatically.
Input Signal Failure
By means of selector plug W1* the actuator can be selected
On actuators with spring return the manual operator is such, that in case of a signal input failure,(e.g. a broken wire)
located under the cover. the actuator will run to one of the three positions:
0%: actuator stem position for 0(2)Vdc
Spring Return 50%: actuator stem in central position
The ML7425A,B spring return types provide a defined safety 100%: actuator stem position for 10Vdc
position of the valve in case of power failure. W1 is set by the factory to 50%.
The spring return actuators are shipped from the factory with
a shipment stop (to lock the knob) in order to allow Input Signal Range
connection of the stem button retainer to the valve stem
The range of the analog input signal Y can be changed by
without power supply.
changing the position of selector plug W2*
EN0B-0624GE02 R0399 2
ML7420A/ML7425A,B
Action
The direction of action can be changed by repositioning of Auxiliary potentiometer
selector plug W3*. It is set by the factory such that the stem Auxiliary potentiometers are available for mounting on site.
extends at increasing signal and retracts at decreasing They can be used as feedback potentiometer and or to
signal. provide remote indication to the valve position.
A cable gland PG13.5 is delivered with the unit.
NOTE
CAUTION Part number: 43191679-011 (10kΩ)
Part number: 43191679-012 (220Ω)
*Jumper plugs W1, W2 and W3 are accessible after the
cover has been removed. They are located on the rear High Temperature Kit
side of the protection sheet of the printed circuit board (for applications >150°C medium temperature)
(see EN1C-0073 and EN1C-0074).
High Temperature Kit, Valve DN
Output Signal ”POSITION” Order Number
An analog output signal 2 to 10Vdc ”POSITION” is available V5011A/V5011K 15 - 40
which represents the actual actuator position. It can be used V5013A/V5013G 15 - 40
43196000-001
for remote indication. V5011R/V5013R 15 - 50
When the actuator stem is extended the output signal is V5328A/V5329A 15 - 32
10Vdc.
V5011A 50
Accessories V5013A/V5013G 50
43196000-002 V5328A/V5329A 40 - 80
Auxiliary switches V5049A 15 - 65
The actuators can be equipped on site with an auxiliary V5050A 15 - 80
switch unit with two switches. Their switching points are
adjustable over the full length of the actuator stroke. The
switches can be used to switch pumps or provide remote
indication of any stroke position.
A cable gland PG13.5 is delivered with the unit.
Part number: 43191680-005
CLOSE-OFF PRESSURE RATINGS in kPa
Stem Force 600N
Stroke 20mm
Valve mm 15 20 25 32 40 50 65 80
Size inch 1/2 3/4 1 1 1/4 1 1/2 2 2 1/2 3
Valves Close-Off Pressure Ratings
V5011R 1600 1600 1000 700 460 260
V5011K 1600 1600 1300 1000
V5013R 1600 1600 1000 700 460 260
V5328A 1600/1000 1000 1000 600 350 200 120 50
V5329A (PN16) 1000 1000 1000 790 480 260 160 100
V5329C (PN6) 600 600 600 600 480 260 160 100
V5049A 1600/1000 1000 1000 600 350 200 120
V5050A 1000 1000 1000 600 350 200 120 50
V5095A 1600 1600 1600 1600 1600 1600 1600
For specific data of above valves see Specification Data No.:
V5011R EN0B-064
V5011K EN0C-0560
V5013R EN0B-065
V5328A EN0C-0432
V5329A,C EN0C-0434
V5049A EN0C-0433
V5050A EN0C-0435
V5095A EN0C-0490
3 EN0B-0624GE02 R0399
ML7420A/M7425A,B
DIMENSIONS
ML7420A ML7425A,B
∗with High Temperature Kit 402mm ∗with High Temperature Kit 444mm
Fig. 1 Dimensions in mm
EN0B-0624GE02 R0399 4
ML7420A/ML7425A,B
WIRING
ML7420A ... - 1/- 2/- 3 ML7420A ... - 4
0 / 50 / 100%
0 - 10V/2 - 10V /
W2 W1 W3 POSITION
2-10Vdc
3 Y
0-10Vdc POSITION
2-10Vdc
2 24V 24V 3 Y
0-10Vdc
M 1 24V 24V 2 24V
24V
C 1
1 24V 24V
D 2
C 1
D 2
CENTRA
CENTRA
ML7425A,B ... - 1/- 3 ML7425A,B ... - 4
0 / 50 / 100%
0 - 10V/2 - 10V /
W2 W1 W3 POSITION
2-10Vdc
3 Y
0-10Vdc POSITION
2-10Vdc
2 24V 3 Y
24V 0-10Vdc
M 1 24V 24V 2 24V
24V
C 1
1 24V 24V
D 2
C 1
S B D 2
CENTRA S B
CENTRA
Auxiliary Switches (Option - Part Number: 43191680 - 005)
1 2 3 4 5 6
S1 S2
250Vac/10A
Fig. 2 Wiring
5 EN0B-0624GE02 R0399
ML7420A/ML7425A,B
Honeywell Regelsysteme GmbH
Honeywellstr. 2-6
D-63477 Maintal
Tel. (0 61 81) 401-1
Fax (0 61 81) 401-400
Manufacturing location is certified according to
DIN
Subject to change without notice. Printed in Germany
EN ISO 9001
EN0B-0624GE02 R0399
