12/26/24, 12:20 AM Worked Example: Retaining Wall Design | The Structural World

Design of Retaining Wall

The Structural World > Topics > Shear Wall Design > Design of Retaining Wall

29
Shares

29

l thestructuralworld } March 4, 2019 v 53 Comments

m Shear Wall Design, Site Construction Design  cantilever retaining wall, design of retaining wall,
retaining wall design calculations excel

Our previous article, Retaining Wall: A Design Approach discusses the principle and concept behind and when
and where to consider a retaining wall in our design. We have learned the different checks against the mode of
failures in the retaining wall should be considered in the design. To further understand the designed approach, here
is a worked example of the design of the retaining wall.

This example is intended to be readily calculated by hand although a lot of structural spreadsheets and software
such as Prokon are available. The purpose of this article is for the reader to fully understand the principle behind it.

Worked Example:
[Link] w w .thestructuralw [Link]/2019/03/04/design-of-retaining-w all/ 1/22
12/26/24, 12:20 AM Worked Example: Retaining Wall Design | The Structural World

29
Shares

Figure A.1-Retaining Wall Cross Section

Consider the cantilever retaining wall with the cross-section shown in the above Figure A.1, which retains a 2m
29
depth of soil having the groundwater table at -1.0m level.

Design Parameters:
Soil Bearing Capacity, qall : 100 kPa

Coefficient of Soil Friction, ф: 30°

Unit Weight of Soil, ɣ s : 18 kN/m3

Unit Weight of Water, ɣ w : 10 kN/m3

Unit Weight of Concrete, ɣ c : 25 kN/m3

Surcharge, ω: 12 kN/m2
Ground Water Level: -1m from 0.00 level
Height of Surcharge, h: 0.8m
Height of Wall: 2.0m
f’c: 32 Mpa
fy: 460 Mpa
concrete cover: 75mm

1. Analytical Geometry and Variables

Before we proceed with the design, it is important for the designer to know the geometric variable and parameters
of the retaining wall. Refer to Figure A.2 below.

[Link] w w .thestructuralw [Link]/2019/03/04/design-of-retaining-w all/ 2/22

12/26/24, 12:20 AM Worked Example: Retaining Wall Design | The Structural World

29
Shares

Figure A.2-Retaining Wall Geometric Variables

where:
29
H: Height of the retaining wall
L: Width of the base
D: Thickness of the base
B: Width of the toe
C: Stem thickness at the bottom
T: Stem thickness at the top

2. Approximate Proportions of a Cantilever Retaining Wall

The next thing to consider is the assumptions that we can make in terms of the geometry of the retaining wall that
we are designing. Given the height, H of the retaining wall, we can assume or counter check our initial design
considerations should at least according to the following geometric proportions:

Base width: L= 0.5H to 2/3H

Thickness of base: D= 0.10H
Stem thickness at the bottom: C=0.10H
Width of the toe: B= 0.25L to 0.33L
Stem thickness at the top: t=250mm (minimum)

Based on the above approximate geometric proportions, let us assumed the following parameters to be used in our
design:

Base width: L= 1.5m

Base thickness: D= 0.25m
Stem thickness: C=t =0.25m

[Link] w w .thestructuralw [Link]/2019/03/04/design-of-retaining-w all/ 3/22

12/26/24, 12:20 AM Worked Example: Retaining Wall Design | The Structural World

Width of Toe: B= 0.625m

3. Analytical Model
Sketches of the retaining wall forces should be considered to properly distinguish the different forces acting on our
retaining wall as tackled in the previous article, Retaining Wall: A Design Approach. Based on our example in
Figure A.1, we have the forces due to soil pressure, due to water and surcharge load to consider. Figure A.3 below
is most likely our analytical model.
29
Shares

READ ALSO: Choosing the Suitable Shoring or Earth Retaining Systems for your Project

29

Figure A.3-Retaining Wall Forces Diagram

Considering the Figure A.3, we can derive the following equation for the active pressures, Pa and passive pressure
Pp. Notice that the pressures acting on the wall are equivalent to the area (triangle) of the pressure distribution
diagram. Hence,

Pa 1=1/2 ɣKaH2 →eq. 1, where H is the height of retained soil

Pa 2=1/2 ɣHw 2 →eq.2, where Hw is the height of the groundwater level

Pa 3=ωKah →eq.3, where h is the height of surcharge

The passive pressure, Pp would be:

Pp=1/2 ɣkpHp2 →eq.4

Values of Coefficient of Pressure, ka and kp

According to Rankine and Coulomb Formula, the following are the equation in calculating the coefficient of
pressure:

Ka= (1-sin ф)/(1+sin ф)

Ka= 0.33

[Link] w w .thestructuralw [Link]/2019/03/04/design-of-retaining-w all/ 4/22

12/26/24, 12:20 AM Worked Example: Retaining Wall Design | The Structural World

Kp= (1+sin ф)/(1-sin ф)

Kp= 3

Substituting the values, we have the following results:

Pa1=1/2 ɣkaH2 = 11.88kN

Pa2=1/2 ɣHw 2= 5kN

29
Pa3=ωk ah= 3.17 kN
Shares

Pp=1/2 ɣkpHp2= 9.72kN

3. Stability Check:
There are two checks to consider the stability of the retaining wall. One is the check for an overturning moment and
the other one is the check for sliding. The weight of the retaining wall including the gravity loads within it plays a vital
role in performing the stability check. Refer to Figure A.4 for the mass or weight calculations.

29

Figure A.4-Retaining Wall Weight Components

The self-weight component of the retaining wall should be factored down or to be multiplied by weight reduction
factor (0.9) to account for uncertainty because they are “stabilizing” in this context. Hence,

Weight due to soil: W 1= 18kN/m3 x 0.6m x 0.625m x 1.0m = 6.75kN

Weight due to footing: W 2= 0.9 x 25kN/m3 x 0.25m x 1.5m x 1.0m = 8.44kN

Weight due to wall: W 3= 0.9 x 25kN/m3 x 0.25m x 2.0m x 1.0m = 11.25kN

Weight due to soil: W 4= 18kN/m3 x 0.625m x 2.0m x 1.0m = 22.5kN

Weight due to water: W 5= 10kN/m3 x 0.625m x 1.0m x 1.0m = 6.25kN

Weight due to surcharge: W s = 12kN/m2 x 0.625m x 1.0m = 7.5kN

Total Weight, W T = 62.69kN

3.1 Check for Overturning Moment:

[Link] w w .thestructuralw [Link]/2019/03/04/design-of-retaining-w all/ 5/22
12/26/24, 12:20 AM Worked Example: Retaining Wall Design | The Structural World

To satisfy the Overturning Moment Stability, the following equation should follow:

where:

29RM: Righting Moment due to the weight of the retaining wall

Shares
OM: Overturning Moment due to lateral earth pressure

With reference to Figure A.4 diagram and taking moment at the point, P conservatively neglecting the effect of
passive pressure hence:

RM= W 2 (0.75) + W 3(0.75) + W 4(1.19) + W 5(1.19) + W s (1.19) = 57.91 kNm

OM= Pa1 (0.67) +Pa2 (0.33) +Pa3 (0.4) = 10.88kNm

READ
29 ALSO: Criteria in Selecting Suitable Foundation in Structural Design of Buildings

RM/OM = 5.32 > 2.0, hence SAFE in Overturning Moment!

3.2 Check for Sliding

To satisfy the stability against sliding, the following equation should govern:

where:

RF: Resisting Force

SF: Sliding Force

The sliding check should be carried out with reference to the Figure A.4 diagram and considering the summation of
vertical forces for resisting force and horizontal forces for sliding force conservatively neglecting the passive
pressure, hence:

RF= W 1+W 2+W 3+W 4+W 5+ W s = 55.94kN

SF= Pa1+Pa2+Pa3 = 20.05kN

RF/SF = 2.79 > 1.5, hence SAFE for Sliding!

[Link] w w .thestructuralw [Link]/2019/03/04/design-of-retaining-w all/ 6/22

12/26/24, 12:20 AM Worked Example: Retaining Wall Design | The Structural World

4. Check the Wall Thickness for Shear

The nominal shear is equal to the lateral forces on the retaining wall, neglecting the effect of passive pressure
which will give us:

Nominal Shear, Vn = 20.05kN

Ultimate Shear, Vu = 1.6Vn = 32.08kN

For29the thickness of the wall to be safe in shear, the ultimate shear, Vu should less than the allowable shear, Vallow
Shares
as recommended by the ACI 318 code.

Vc = 0.17√fc’bw d

where: ф=0.75

29 bw=1000mm

d= 250mm-75mm-6mm = 169mm

Vc = 0.17√fc’bwd = 162.52kN

Vallow = 121.89kN

Since Vu < Vallow, hence SAFE in Shear!

5. Design the Wall Stem for Flexure

Nominal Moment, Mn = 10.88kNm

Ultimate Moment, Mu = 1.6Mn = 17.40kNm

Mu =φ fc’ bd2ω (1- 0.59 ω)

17.40×106 = 0.90 x 32 x 1000 x 1692 ω (1-0.59 ω)

ω = 0.0216

ρ = ω fc’/fy= 0.00150

As= ρbd = 0.00150x1000x169 = 254mm 2

As min= ρminbt = 0.002 x 1000 x 250 = 500mm 2

[Link] w w .thestructuralw [Link]/2019/03/04/design-of-retaining-w all/ 7/22

12/26/24, 12:20 AM Worked Example: Retaining Wall Design | The Structural World

Required Vertical Bar: Try T10-200; As act = 392mm 2 x 2 sides = 785.4mm 2

Required Horizontal Bar: Try T10-250; As act = 314mm 2 x 2 sides= 628.32mm 2

Hence: use T10-200 for vertical bar and T10-250 for horizontal bar.

6. Check for Bearing Pressure under Footing

29
The foundation bearing capacity usually governs the design of the wall. The soil, particularly under the toe of the
Shares

foundation, is working very hard to resist the vertical bearing loads, sliding shear, and to provide passive resistance
to sliding. The bearing capacity of the soil should be calculated taking into account the effect of simultaneous
horizontal loads applied to the foundation from the soil pressure.

For the footing to be safe in soil pressure, the maximum soil pressure under working load shall be less than the
allowable soil bearing capacity. The maximum soil bearing pressure under the footing considering 1m strip is:

29

where:

P= 62.69kN

A= (1×1.5) m2
M=10.88 kNm
b= 1m
d=1.5m

Substituting the values above will give us:

qmax = 70.81kPa < qall= 100 kPa, hence, oK!

Solving for Ultimate bearing pressure:

where:

P= 1.6x 6.75 + 1.4×8.44 +1.4×11.25 +1.6x 22.5 +1.6×6.25 +1.6×7.5= 96.37kN

A= (1×1.5) m2

[Link] w w .thestructuralw [Link]/2019/03/04/design-of-retaining-w all/ 8/22

12/26/24, 12:20 AM Worked Example: Retaining Wall Design | The Structural World

M=17.40kNm
b= 1m
d=1.5m

Substituting the values above will give us:

qum ax= 110.65kN

qum in= 17.85kN

29
Shares

7. Check the Required Length of the Base

If qumin is in tension check the required length otherwise ignore if it is in compression. Since our qumin is tension
(+), the value of L must be computed as follows:

READ ALSO: How to Write a Construction Method Statement from Scratch

29

Figure A.5-Pressure Diagram under Tension

From Figure A.5:

Solve for Eccentricity:

e=M/P = 0.181

[Link] w w .thestructuralw [Link]/2019/03/04/design-of-retaining-w all/ 9/22

12/26/24, 12:20 AM Worked Example: Retaining Wall Design | The Structural World

where:

a=length of pressure
qe= qumax

b=1 meter strip

29
Shares
a= 1.74m

L= 2(e+a/3) = 1.52 say 1.6m

8. Check the Adequacy of Footing Thickness for Wide Beam Shear

29

Fig A.6-Pressure Diagram under Compression

8.1 When qumin is in Compression

Solving for y by similar triangle: referring to Figure A.6 above

y/1.044 = (112.24-19.44)/1.5; y = 64.59 kPa

qc = 19.44 + 64.59 = 84.03 kPa

[Link] w w .thestructuralw [Link]/2019/03/04/design-of-retaining-w all/ 10/22

12/26/24, 12:20 AM Worked Example: Retaining Wall Design | The Structural World

L’= (1.5m-1.044m) = 0.456m

B= 1m strip
qumax =112.24kPa

29
Vu= 44.75kN
Shares

8.2 When qumin is in Tension

qc=y

Solving for y by similar triangle: (referring to Figure A.6 above, L=a=1.75)

y/1.244=
29 112.24/1.75; y = 79.79 kPa

qc=79.79kPa

Vu= 1/2 (qc + qumax ) L’b

L’= (1.6m-1.244m) = 0.356m

B= 1m strip
qumax =112.24 kPa

Vu=34.18kN

Hence, use: Vu=44.75kN

Vallow= фVc

Vc = 0.17√fc’bwd

where:

ф=0.75
bw =1000mm

d= 250mm-75mm-6mm = 169mm

Vc = 0.17√fc’bwd = 162.52kN

[Link] w w .thestructuralw [Link]/2019/03/04/design-of-retaining-w all/ 11/22

12/26/24, 12:20 AM Worked Example: Retaining Wall Design | The Structural World

Vallow = 121.89kN

Since Vu < Vallow , hence SAFE in Shear!

9. Check the Wall Thickness for Flexure

29
Shares

29

Figure A.7-Pressure Diagram for Flexure Check

9.1 When qumin is in Compression

Solving for y by similar triangle:(referring to Figure A.7 above)

y/0.875 = (112.24-19.44)/1.5; y = 54.13 kPa

qc= 19.44 + 54.13 = 73.57 kPa

Mu= (73.57×0.625) x (0.625/2) + (38.67×0.625) (1/2) x (2/3) (0.625) → (area of trapezoid x lever arm)

Mu=19.40 kNm

9.2 When qumin is in Tension

qc= qumin + y

Solving for y by similar triangle: (referring to Figure A.7 above. L=a=1.75)

[Link] w w .thestructuralw [Link]/2019/03/04/design-of-retaining-w all/ 12/22

12/26/24, 12:20 AM Worked Example: Retaining Wall Design | The Structural World

y/1.075 = 112.24/1.75; y = 68.95 kPa

qc=19.44 + 68.95= 88.39 kPa

Mu = (88.39×0.75) x (0.75/2) + (23.85×0.75) (1/2) x (2/3) (0.75) → (area of trapezoid x lever arm)

Mu= 19.40kNm

Hence, use Mu=29.33kNm

29
Shares
Mu =φ fc’ bd2ω (1- 0.59 ω)

29.33×106 = 0.90 x 32 x 1000 x 1692 ω (1-0.59 ω)

ω = 0.0364

ρ = ω fc/fy= 0.002532

As= ρbd = 0.002532x1000x169 = 428mm 2

29

As min= ρminbt = 0.002 x 1000 x 250 = 500mm 2

Required Vertical Bar: Try T10-200; As act = 392mm 2 x 2 sides = 785.4mm 2

Required Horizontal Bar: Try T10-250; As act = 392mm 2 x 2 sides= 628.32mm 2

10. Reinforcement Details of Retaining Wall

The presented calculations above are actually too tiring to perform manually especially if you are doing a trial and
error design. Thanks to structural design soft wares and spreadsheets, available nowadays, our design life will be
[Link] w w .thestructuralw [Link]/2019/03/04/design-of-retaining-w all/ 13/22
12/26/24, 12:20 AM Worked Example: Retaining Wall Design | The Structural World

easier.

Our team developed a user-friendly spreadsheet for the design of cantilever retaining wall based on the above
calculation. Grab your copy here!

What do you think about this article? Tell us your thoughts! Leave a comment on the section below. Subscribe to
our newsletter to be updated with the latest posts or follow us on our social media pages on the below icons.
29
Shares

279980 total views , 30 views today

Advertisements

← Previous post Next post →

29

53 Comments

Mohmand Andar September 18, 2019 at 4:16 pm

i need for your help minimum depth for stone masonry wall refer to ACI code is how much?
kindly send me with Ref of ACI code

thestructuralworld (Post author) October 10, 2019 at 3:53 pm

You can use the parameters written in section 2 of this article and confirm whether the thickness is adequate
using a shear check.

Ross October 11, 2019 at 11:39 am

This is a helpful guide to Retaining Wall design. However, I have noticed errors in Section 3’s loadings. For example, Pp is not
substituted correctly. I have not checked further than this.

It would be worth double-checking the spreadsheet you are selling as this is a dangerous error that would show a retaining wall
having a higher capacity than it actually does.

thestructuralworld (Post author) October 13, 2019 at 3:34 pm

[Link] w w .thestructuralw [Link]/2019/03/04/design-of-retaining-w all/ 14/22

12/26/24, 12:20 AM Worked Example: Retaining Wall Design | The Structural World

Thanks for pointing out. We have checked and found out that that is merely a typo error and it has been
updated accordingly. We have also double-checked the attached spreadsheet and it is not affecting the results
as we conservatively neglect the effect of passive pressure in the calculation.

Intisar October 22, 2019 at 9:08 am

29 guide. Which section in ACI360 the calculations are referred to?

Helpful
Shares

Edgar October 29, 2019 at 9:15 am

Hello

Can you explain why the height of the surcharge is only 0.8m and why is it not reflected on the Analytical model ?

Its very detailed example , thanks for that.

29
Edgar October 29, 2019 at 12:33 pm

Also ,would you be able to explain how is the d in critical shear calculated ? number 1.044 is used for similar
triangles,however I struggle to find exact theory how you arrived to this number as I get different.

thestructuralworld (Post author) November 4, 2019 at 2:47 am

Substitute the values from (L-T)/2 + T + d, where L=1.5, T=0.25 and d=.169. That will give us 1.044.

thestructuralworld (Post author) November 2, 2019 at 6:35 pm

In this example, a 0.80m surcharge height is a given parameter. In the analytical model, the surcharge, ω is
mentioned and the height corresponds to that is 0.80 m.

Rosina October 29, 2019 at 2:39 pm

Very helpful information.. thanks for sharing

thestructuralworld (Post author) November 2, 2019 at 6:36 pm

Thanks Rosina!

[Link] w w .thestructuralw [Link]/2019/03/04/design-of-retaining-w all/ 15/22

12/26/24, 12:20 AM Worked Example: Retaining Wall Design | The Structural World

Renzo January 14, 2020 at 9:33 am

where do you get this 1.244 on similar triangles under (qc = y) condition. Thanks in advance!

Ant April 1, 2020 at 4:26 am

29
You need to use effective stress when doing the calculation.
Shares

bricklayer April 14, 2020 at 10:12 pm

we have to learned the different checks against the mode of failures in the retaining wall should be considered in the design. Here
some worked examples of the design of the retaining wall are described.I like the I have also found this resource [Link]
useful and its related to what you are mentioning.

29 KL June 9, 2020 at 9:07 am

Could you please clarify why in section 7 you determine L=1.6m, but later in the calculation you still use L=1.5m? thanks a lot.

Charles July 9, 2020 at 5:34 pm

I find this helpful though.

Samir Khan December 30, 2020 at 2:39 am

In the overturning moment, you have this factor: W1 (0.313)

Where do you get the 0.313 from?

PS I purchased the spreadsheet!

Elifnur Kanburoğlu December 30, 2020 at 7:19 pm

why we used 18 kn/m^3 insted of 12 kn/m^3 when we calculate the weight of surcharge?

thestructuralworld (Post author) December 31, 2020 at 4:18 pm

This is just a typo error and we corrected this according to 12KPa as per the attached spreadsheet.

[Link] w w .thestructuralw [Link]/2019/03/04/design-of-retaining-w all/ 16/22

12/26/24, 12:20 AM Worked Example: Retaining Wall Design | The Structural World

Ranjana January 8, 2021 at 3:52 pm

while calculating restoring moment is it good to take moment due to surcharge load because surcharge
load may be transient in some cases , like fire tender or other vehicular load

29 EDUARDO CINCO ARENAS February 27, 2021 at 4:21 am

Shares

fine example for design

Sadhbh April 29, 2021 at 5:43 pm

Why did you put 1/2 for Pa1 instead of 1/3 as it is H/3 with triangular load?

thestructuralworld (Post author) May 2, 2021 at 12:21 am

29

Notice that the pressures acting on the wall are equivalent to the area (triangle) of the pressure distribution diagram.
Upon getting the Pressure, we will multiply it by h/3 to get the moment.

Meaghan May 3, 2021 at 11:20 am

What does the height of the surcharge, h, represent? You have given us the value of the surcharge, so I can’t work out what the h
is referring to?

Verna Owen May 27, 2021 at 7:17 am

I’m amazed at your Math skills! However, retaining walls can also be built through stone masonry construction. But yeah, the
cost and quality should be considered.

Shahram Aftabiazar August 25, 2021 at 2:29 am

Hi,
in the section “Check for Sliding”, I think you have forgotten to multiply the vertical weight to “tan([Link]/3)”. if you do that Rf would
be reduced 55.94 x 0.35= 19.50, as a result, the design cannot pass the sliding check.
the active lateral load should be against the passive lateral load, not the vertical load.

[Link] w w .thestructuralw [Link]/2019/03/04/design-of-retaining-w all/ 17/22

12/26/24, 12:20 AM Worked Example: Retaining Wall Design | The Structural World

Casey Roberts September 7, 2021 at 11:20 pm

Does this spreadsheet allow for an offset footing where the toe length is different than the heel lenth.

Also, why vertical rebar on both faces of the stem? Primary vertical rebar should be on the tension (back/burried) face.

thestructuralworld (Post author) September 15, 2021 at 9:03 pm

29
Shares
This excel is for retaining walls with concentric walls to its foundation only. Yeah, that’s right theoritically, the
primary bar should place on the tension side of the wall only. But, practically speaking, or in actual it’s best for
the designer to add another rebar on the other side, just in case.

Ruben Fegsar September 15, 2021 at 4:42 pm

I bought the file, yet why cant I edit the file so i may be able to put my own logo for the finished output?
29
Is it not allowed? I mean like I already paid for the file.

Thanks and would really appreciate a feedback on this one.

thestructuralworld (Post author) September 15, 2021 at 8:51 pm

Hi Ruben, you can actually put your own logo on the space provided. Either editing some option setting on your excel
or typing your company name on it. If none of these options are working, do it manually. Once you finish the design,
convert the file to pdf and paste your logo from there.

Hiwotie September 29, 2021 at 7:59 pm

it would have been better, if you can reference the equations.

Nadirlaini Souza October 7, 2021 at 2:09 pm

Hi, thank you for this example. It is really helpful.

I just have a question about the unit weight of soil used. Below the groundwater level, the active earth pressure shouldn’t be
calculated considering the submerged unit weight of soil?

portland baic October 17, 2021 at 7:29 pm

[Link] w w .thestructuralw [Link]/2019/03/04/design-of-retaining-w all/ 18/22

12/26/24, 12:20 AM Worked Example: Retaining Wall Design | The Structural World

IT CAN BE ALLOWED TO USED THE MINIMUM STEEL RATIO OF 1.4/fy ? for vertical reinf of retaining wall.

Aaron November 1, 2021 at 9:05 pm

I think your RM is incorrect in its total value. Each time I calculate it I get 57.91KN, not 60.02KN

29 thestructuralworld (Post author) November 3, 2021 at 10:56 pm

Shares

Thanks, Aaron for pointing it out. We have checked and found out that that is merely a typo error and it has
been updated accordingly. We have also double-checked the attached spreadsheet and it is not affecting the
results in the calculation.

Ashim Saha November 30, 2021 at 1:14 pm

Sir,29
would you please to explain about qumax 112.24 and qumin 19.44 respectively of article [Link].

John Edwin December 24, 2021 at 6:11 pm

This sit is very good,how can i become member.

Sangeetha February 9, 2022 at 1:53 pm

Hi, Thanks for the detailed calculation. How if the surcharge height is not given, what estimation can we use?

thuan cao March 13, 2022 at 10:42 pm

is there unit in imperial ? or only in metric

thestructuralworld (Post author) March 17, 2022 at 10:04 pm

This is in the metric unit. Imperial or SI unit is under development.

Heinrich May 8, 2022 at 4:17 pm

Good day
Our lecturer used this exact extract as a curveball to calculate retaining walls with water, I found this before we had to give it in…

[Link] w w .thestructuralw [Link]/2019/03/04/design-of-retaining-w all/ 19/22

12/26/24, 12:20 AM Worked Example: Retaining Wall Design | The Structural World

full marks then :D.

Why do you not use friction forces to calculate FR, FR = ΣV * tan(k1*Φ1) + k2C2B + Pp

There is no cohesion forces hence k2C2B = 0

But the rest will equate to 32.54kN

Then sliding test will be 1.62>1.5 = OK, this is how we are taught.

Could you elaborate on your method for sliding and where the 0.9 safety factor comes from for the concrete weight. I have tried to
29
find this info in our foundations handbook with no success.
Shares

Heinrich May 8, 2022 at 7:56 pm

I also see your turning point is not at an extreme point. You use the top of your toe instead of the bottom. From what I can
see this means your moments won’t be accurate, but it will give similar results.

There is also a comment earlier about a typo of MoT = 57.91, the figure was right at 60.02, the weight of section 1 was not
added to the equation. Though all of these moments are taken from the top of the toe and not the furthest point, thus
29
moments are not accurate.

Principle is good, great article.

[Link] November 2, 2022 at 4:19 pm

sir, Thank you for your valuable information. this is very much useful and one more plea that can we have any examples for
considering wings & returns with head wall can be treated as a retaining wall any such kind of examples please post to mail if
any thanks in advance

Mike January 25, 2023 at 12:41 pm

Hi
Great example. Thanks. Wouldn’t you think you need to add the vertical stress applied on the wall base due to the surcharge and
also calculate its moment?
Thanks
Mike

thestructuralworld (Post author) February 7, 2023 at 11:21 pm

Thanks, Mike! The surcharge is already considered in the example.

[Link] w w .thestructuralw [Link]/2019/03/04/design-of-retaining-w all/ 20/22

12/26/24, 12:20 AM Worked Example: Retaining Wall Design | The Structural World

Matthew April 14, 2023 at 12:33 pm

Good day. May I ask if why bw is equal to 1000 mm? As per ACI R11.1:

The shear strength is based on an average shear stress on the full effective cross section (bw x d). In a member without shear
reinforcement, shear is assumed to be carried by the
concrete web. In a member with shear reinforcement, a portion of the shear strength is assumed to be provided by the concrete
and the remainder by the shear reinforcement.
29
Shares
Thus, the assumed cross section must be 250 mm (base thickness where shear failure is expected) x 169 mm.

Adrian P December 8, 2023 at 11:51 am

Hi, awesome example! I have a question though, in the overtunring moment:

RM= W2 (0.75) + W3(0.75) + W4(1.19) + W5(1.19) + Ws(1.19) = 57.91 kNm
OM= Pa1 (0.67) +Pa2 (0.33) +Pa3 (0.4) = 10.88kNm

where
29
did 0.75, 1.19, 0.67, 0.33 and 0.4 came from? are those USA safety factors or what?

thestructuralworld (Post author) December 20, 2023 at 10:34 pm

Those are lever arms! With reference to Figure A.4 diagram and taking moment at the point P.

Adrian P December 21, 2023 at 12:13 pm

Hey, thanks! I did get now where the

0.67, 0.33 and 0.4 in OM
came from there the height of the resultant,
but I still cant figure out the
0.75 and 1.19 from RM, are they the distance to a certain turning point?

sujit mondal February 11, 2024 at 11:29 pm

would you please to explain about qumax 112.24 and qumin 19.44 respectively ???

Shanks February 21, 2024 at 10:55 am

in check the wall thickness for flexure section

Mu= (73.57×0.625) x (0.625/2) + (38.67×0.625) (1/2) x (2/3) (0.625)

[Link] w w .thestructuralw [Link]/2019/03/04/design-of-retaining-w all/ 21/22

12/26/24, 12:20 AM Worked Example: Retaining Wall Design | The Structural World

How is this calculated

and where did we get 38.67 from
Please explain

Jesus Saves March 6, 2024 at 6:12 pm

Thank for this detailed design to follow; It has been very helpful. One thing I noticed is that the calculation for the wall stem does
29
not match the value you then indicated for the moment when checking for wall stem flexure. You have listed that Mu=19.40KNm
Shares
again for tension, but the calculation comes out to the 29.33KNm you used. I believe it was just a typo but it made it a bit
confusing to follow then. Thanks again, and God bless.

D Grant March 27, 2024 at 6:51 pm

Just an FYI, with water behind the retaining wall, the soil weight should be submerged (subtracting water unit weight from soil) to
determine the active pressure. Without water in front of the wall, you’ll also have an uplift force along the underside of the footing
due29to buoyancy, equal to the depth of water behind the wall at the heel, tapering to the depth of water in front of the wall at the
toe.

[Link] w w .thestructuralw [Link]/2019/03/04/design-of-retaining-w all/ 22/22