Structural Analysis and Design-II (CE 313)
Course Teacher: Dr. Fatema-Tuz-Zahura, Associate Professor, Dept of CE, AUST
Objective
Analysis of Mill Bent
Licensed under the Creative Commons Attribution-Share Alike 4.0 International License 1
Structural Analysis and Design-II (CE 313)
Course Teacher: Dr. Fatema-Tuz-Zahura, Associate Professor, Dept of CE, AUST
For the mill bent shown below, find the reactions and draw SFD, BMD
and AFD for both columns.
Licensed under the Creative Commons Attribution-Share Alike 4.0 International License 2
Structural Analysis and Design-II (CE 313)
Course Teacher: Dr. Fatema-Tuz-Zahura, Associate Professor, Dept of CE, AUST
The degree of indeterminacy
=6 -3 =3
unsupported height
Both Assumptions will be applied
H
1. There is a point of inflection at the H
center of the unsupported height of 5 ft
each fixed based column
2. Total lateral load is equally divided
among the column at the level of
hinges.
Licensed under the Creative Commons Attribution-Share Alike 4.0 International License 3
Structural Analysis and Design-II (CE 313)
Course Teacher: Dr. Fatema-Tuz-Zahura, Associate Professor, Dept of CE, AUST
1. There is a point of inflection at the
center of the unsupported height of
each fixed based column
Assumptions 2. Total lateral load is equally divided
among the column at the level of
hinges.
For three degree indeterminate structure
unsupported height Both Assumptions
For two degree indeterminate structure
First Assumption
For three degree indeterminate structure
Second Assumption 4
Licensed under the Creative Commons Attribution-Share Alike 4.0 International License
Structural Analysis and Design-II (CE 313)
Course Teacher: Dr. Fatema-Tuz-Zahura, Associate Professor, Dept of CE, AUST
O 5m
H H
T
Vo VT
Total Lateral Load at the Level of Hinges = 2.5*(5+3) +50/√2 = 55.36 kN
So, H = 55.36/2 =27.68 kN
Licensed under the Creative Commons Attribution-Share Alike 4.0 International License 5
Structural Analysis and Design-II (CE 313)
Course Teacher: Dr. Fatema-Tuz-Zahura, Associate Professor, Dept of CE, AUST
12 ft
O 5m
H H
T
Vo VT
∑MT (clockwise +ve) 2.5*8*4+ 8*50/√2 – 12* 50/√2 –VO*12 = 0
VOT == 15 kN K
-5.12
Licensed under the Creative Commons Attribution-Share Alike 4.0 International License 6
Structural Analysis and Design-II (CE 313)
Course Teacher: Dr. Fatema-Tuz-Zahura, Associate Professor, Dept of CE, AUST
Vo 5.12 K
O 27.68 K
O 5m
40.18 K H H
T
-169.65 K-FT VT
5.12 K Vo
Licensed under the Creative Commons Attribution-Share Alike 4.0 International License 7
Structural Analysis and Design-II (CE 313)
Course Teacher: Dr. Fatema-Tuz-Zahura, Associate Professor, Dept of CE, AUST
Section 1-1
∑MC (clockwise +ve) = 27.68*8 – 2.5*8*4 - (FBL)*3 = 0
FBL = 47.15 K
1
F
1
5m
O H H
B T
Vo VT
Licensed under the Creative Commons Attribution-Share Alike 4.0 International License 8
Structural Analysis and Design-II (CE 313)
Course Teacher: Dr. Fatema-Tuz-Zahura, Associate Professor, Dept of CE, AUST
39.47 K
15.18 K
31.97K
107.15 K-FT
40.18 K
169.65 K-FT 5.12 K 40.18 K
169.65 K-FT 5.12 K
Licensed under the Creative Commons Attribution-Share Alike 4.0 International License 9
Structural Analysis and Design-II (CE 313)
Course Teacher: Dr. Fatema-Tuz-Zahura, Associate Professor, Dept of CE, AUST
You are requested to share your questions, idea
and feedback with me using any synchronous or
asynchronous media
Licensed under the Creative Commons Attribution-Share Alike 4.0 International License 10
Structural Analysis and Design-II (CE 313)
Course Teacher: Dr. Fatema-Tuz-Zahura, Associate Professor, Dept of CE, AUST
Licensed under the Creative Commons Attribution-Share Alike 4.0 International License 11
