®
ELECTRONICA
SCiCoreLink62
scicorelink62_i IGBT/MOSFET drivers
PRELIMINARY TECHNICAL INFORMATION
Adaptation board for SCiCoreDrive22
DEFAULT VALUES (board configuration)
- Half-bridge mode (Direct Mode optional)
- 4 µs dead time between channels generated
- Gate resistor depending on the IGBT module used
- 0-5 V input PWM logic levels ( 0-15 V optional) non-contractual image
- 0-5 V fault output (low level open collector output optional)
SCiCoreLink62 is a printed circuit board specially designed for interfacing the 2-channel IGBT driver
module SCiCoreDrive22.
For more accurated information about the behaviour of the entire driver board, timming and electrical
characteristics, please refer to SCiCoreDrive22 datasheet. Gate resistors are not included (by default).
Other configurations than the default one are available by order, please contact with us.
ELECTRICAL CHARACTERISTICS
Description symbol notes/test conditions min. typ. max. units
Supply voltage VCC 14 15 16 V
PWM High state Input voltage VPWM_H 3.5 5 V
JP1 & JP2 connected (1)
PWM Low state Input voltage VPWM_L 0 1.5 V
PWM High state Input voltage VPWM_H 11 15 V
JP1 & JP2 unconnected (1)
PWM Low state Input voltage VPWM_L 0 4 V
Reset High state Input Voltage VRESET_H 2 5 V
Reset Low state Input Voltage VRESET_L 0 0.8 V
Fault open collector current IFAULT working as open collector 8 mA
Fault High state Output Voltage VFAULT_H working in logic level 5 V
indicates fault condition
Fault Low state Output Voltage VFAULT_L 0 0.4 V
open collector or logic level
091106Rev.:1
Note: JP1 and JP2 jumpers are located at SCiCoreDrive22, not at SCiCoreLink62
Reserves the right to change limits, test conditions and dimensions given in
this data sheet at any time without previous notice.
1
®
ELECTRONICA
scicorelink62_i
PINOUT
CON 1 designation function JUMPERS
1 PWMTOP Input logic signal for switching TOP IGBT JP1 both connected: 5 V logic level
2 GND Ground terminal for supply and logic signals JP2 both unconnected: 15 V logic level
3 GND Ground terminal for supply and logic signals right connected: half bridge mode
JP3
4 RESET Reset input signal (low state left connected: direct mode
5 GND Ground terminal for supply and logic signals
6 VCC +15 VDC for supply voltage
7 FAULT fault output signal
8 VCC +15 VDC for supply voltage
9 VCC +15 VDC for supply voltage
10 PWMBOT Input logic signal for switching BOT IGBT
CON 2 designation function
1 COLLECTORTOP TOP IGBT collector desaturation sensing
2 GATETOP TOP IGBT gate signal
3 EMITTERTOP TOP IGBT emiter signal
CON 3 designation function connector CON1:
type TYCO 1-1634688-0
1 COLLECTOR BOT BOT IGBT collector desaturation sensing
2 GATE BOT BOT IGBT gate signal connectors CON2, CON3:
type MULTICOMP MC34391
3 EMITTER BOT BOT IGBT emiter signal
1 2 3 1 2 3
CON 2:1
CON 2 CON 3
CON 2:2
CON 2:3
CON 3:1
CON 3:2
CON 3:3
HB
PWR
JP3 LED
9 7 5 3 1
CON 1
DM
091106Rev.:1
10 8 6 4 2 mounting considerations:
cables between PCB and IGBT must be as short as possible.
All dimensions in mm. Gate and emitter conections slould be twisted pair
Reserves the right to change limits, test conditions and dimensions given in
this data sheet at any time without previous notice.
2
®
ELECTRONICA
scicorelink62_i
GATE RESISTORS
By default the board do not include any gate resistor. User must solder on gate resistors pads the required
resistance. For each channel it is available 3 resistor spaces for RG ON and for RG OFF.
The available pads on PCB are suitable for 1206 SMD resistors.
TOP GATE BOT GATE
RESISTORS RESISTORS
DEAD TIME CAPACITORS
By default SCiCoreLink62 includes the dead time capacitors needed for a 4 µs between channels. Please
refer to SCiCoreDrive22 datasheet if you want to change the default dead time and calculate its necessary
capacitance.
The available pads on PCB are suitable for SMD capacitors. It is highly recommended a good value match-
ing between channel dead time capacities.
TOP DEAD TIME BOT DEAD TIME
CAPACITOR CAPACITOR
HB
PWR
LED
DM
091106Rev.:1
Reserves the right to change limits, test conditions and dimensions given in
this data sheet at any time without previous notice.
3
®
ELECTRONICA
scicorelink62_i
Cost Effective Products
SEMICODE ELECTRONICA
offers to the market a comprehensive range of products from recognized manufacturers at the best price/
quality relationship, this products are provided with a basic reference code that allows maintaining the same
product reference even if the original device manufacturer is replaced. SEMICODE product reference has
to be considered as a generic brand.
Seeking the market needs and trends, we are constantly increasing the product portfolio with new products
and suppliers, please ask for the updated information available to our local contacts.
SEMICODE products include semiconductors, passive components and accessories focused in power
electronics market.
Datasheet Annotations:
SEMICODE ELECTRONICA annotate datasheets in the top left hard corner of the front page, to indicate
product status. The annotations are as follows:
Tentative information: This is the most tentative form of information and represents a very preliminary
specification. No actual design work on the product has been started.
Preliminary Information: The product is in design and development. The datasheet represents the product
as it is understood but details may change.
Advance Information: The product design is complete and final characterisation for volume production is
well in hand.
No Annotation: The product parameters are fixed and the product is available to datasheet specification.
NOTICE: The technical data are to specify components, not to guarantee their [Link] warranty or guarantee
expressed or implied is made regarding delivery or performance. The Company reserves the right to alter without prior notice the
specification of any product. Information concerning possible methods of use is provided as a guide only and does not constitute
any guarantee that such methods of use will be satisfactory in a specific piece of equipment. It is the user’s responsibility to fully
determine the performance and suitability of any equipment using such information and to ensure that any publication or data used
is up to date.
All brand names and product names used in this publication are trademarks, registered trademarks or trade names of their
respective owners.
091106Rev.:1
© SEMICODE ELECTRONICA 2008. TECHNICAL DOCUMENTATION – NOT FOR RESALE
Reserves the right to change limits, test conditions and dimensions given in
this data sheet at any time without previous notice.
