RESISTO DMR 16
RS RESISTOR
FIG.1
POWER RATINGS TABLE 1 RATINGS
Resistors shall have a power rating based on continuous Rated Power 0.4W at 70˚C
full-load operation at an ambient temperature of 70˚C. Max. Working Voltage 200V
For temperature in excess of 70˚C, the load shall be Max. Overload Voltage 400V
derated as shown in the figure 1. Rated ambient temp. 70˚C
Operating Temp. Range -55˚C to +155˚C
Resistance tolerance ± 1%
Resistance range 10Ω to 1MΩ
VOLTAGE RATINGS
Resistors shall have a rated direct-current (DC)
continuous working voltage or an approximate sine-wave
root-mean-square (RMS) alternating-current (AC) CONSTRUCTION
SECTIO
continuous working voltage at
commercial-line frequency and waveform corresponding to the
power rating, as determined from the following formula: No. Name Material
RCWV = P X R 1 Basic Body Rod type ceramics
2 Resistor Metal Film
3 End Cap Steel (Tin plated Iron surface)
DMR SELECTION GUIDE 4 Lead Wire Annealed Copper wire (electrosolder plated
surface)
5 Joint By welding
Where: RCWV = rated DC or RMS AC continuous
working voltage at commercial-line frequency and 6 Coating Insulated resin (colour - apple green)
waveform (Volt) 7 Colour Code Epoxy resin
P = Power rating (Watt)
R = Nominal resistance (Ohm)
In no case shall the rated DC or RMS AC continuous
working voltage be greater than the applicable maximum
value.
NOMINAL RESISTANCE
Effective figures of nominal resistance shall be in
accordance with E-24 series, and resistance tolerance
shall be shown by table 1.
ORDERING INFORMATION
DMR 16 T 75R
Type Taping Value
16 = 0.4W BD= Tape in ohms
and
reel
1
[Link].
RESISTO DMR 16
RS RESISTOR
T = Tape
and
ammo
Please note taping specification is available on page 134.
2
[Link].
RESISTO DMR 16
RS RESISTOR
SPECIFICATION
PERFORMANCE TEST TEST METHOD APPRAISE
Short Time Overload JIS-C-5202 5.5 2.5 Times RCWV for 5 seconds ± (0.25%+0.05Ω)
Dielectric Withstanding Voltage JIS-C-5202 5.7 in V- Block for 60 seconds by Type
Temperature Coefficient of Resistance JIS-C-5202 5.2 -55˚C to 155˚C by Type
Insulation Resistance JIS-C-5202 5.6 in V-Block >10000MΩ
Solderability JIS-C-5202 6.5 260˚C for ±5 Seconds 95% Min. Coverage
Resistance to Solvent JIS-C-5202 6.9 Trichloroethane for 1 Min. with Ultrasonic No Deterioration of
coatings & markings
Terminal Strength Direct Load for 10 Sec. in The Direction of Terminal Leads >2.5kg (24.5N)
Pulse Overload JIS-C-5202 5.8 4 Times RCWV 10000 Cycles (1 Sec. on, 25 Sec. off) ±(2%+0.05Ω)
Load Life in Humidity JIS-C-5202 7.9 40±2˚C, 90~95% RH at RCWV for 1000 hrs. ±(1.5%+0.05Ω)
(1.5 Hrs. on, 0.5 Hrs. off)
Load Life JIS-C-5202 7.10 70˚C at RCWV for 1000 Hrs. (1.5 Hrs. on, 0.5 Hrs off) ±(1.5%+0.05Ω)
Temperature Cycling JIS-C-5202 7.4 -55˚C Room Temp. 155˚C Room Temp. for 5 Cycles ±(0.25%+0.05Ω)
Resistance to Soldering Heat JIS-C-5202 6.4 350˚C ± 10˚C for 3±0.5 seconds ±(0.25%+0.05Ω)
OUTLINE DRAWING
SECTIO
L D d+ 0.05 H±2
(max.) (max.)
3.3+0. 1.8+0. 0.5mm 28
4 3
3
[Link].
