.

Architecture material list

No. in BOQ. No. Item Category

Mosaic glass (Light blue)
1-3 1 Swimming pool finishes
CODE:TL-01
Mosaic glass (Dark blue)
2-3 2 Swimming pool finishes
CODE:TL-02
Mosaic glass (Light green)
3-3 3 Swimming pool finishes
CODE:TL-03
Triesta beige marble
4-3 4 Swimming pool finishes
CODE:TR-01
Stainless-steel swimming
1-4 5 Swimming pool accessories
pool ladder
3-6 6 Antibacterial ceramic Balance tank flooring and wall finishes
Vertical stainless-steel
5-6 7 Pump room accessories
ladder for pump room
6-6 8 Stainless-steel access door Pump room accessories
Epoxy painting for flooring
7-6 9 Pump room flooring and wall finishes
and wall pump room
Adhesive material for
- 10 Swimming pool finishes
Mosaic and marble
Grouting material for
- 11 Finishing material
mosaic, ceramic and marble

6 South Lotus, 90 St. New Cairo, Egypt // Phone: +020 111 000 665 5 // Office: +02 254 089 51
WWW.ASQUAREDEG.COM
MasterTop® 1200
Two-component solvent free epoxy resin

DESCRIPTION GUIDE TO APPLICATION

MasterTop 1200 is a solvent free epoxy used as
primer and sealer for MasterTop epoxy flooring AS A SEALER / PRIMER
systems. Remove all surface laitance, oil, grease or any
defective concrete that will reduce the bond of the
PRIMARY USES
MasterTop 1200 to the substrate.
MasterTop 1200 may be used as the surface
sealer/primer for MasterTop 1210 and Surface irregularities must be ground down or
MasterTop 1230. Also, as a basecoat and sealer filled out with MasterTop 2200 or repair materials
for MasterTop 1221A. from the MasterEmaco & MasterTop ranges.
A light etch giving the texture of medium grit sand
MasterTop 1200 may be used in the following paper is the ideal surface profile for the application
industries: of MasterTop 1200, this can be achieved by
 Pharmaceutical & medical laboratory captive blasting or light grit blasting.
situations.
 Food and beverage production. After preparation has been completed, ensure all
 Car production facilities. dust is removed from the surface.
 Aircraft hangars and maintenance areas.
 Warehouses - for installations with a medium Prior to application MasterTop 1200 should be
frequency and volume of traffic. stored under cover and protected from extremes
 Traffic decking & car parks of temperature which will cause inconsistent
 Exhibition halls workability, finish and cure times for the mixed
material. Ideally at least 24 hours before mixing,
ADVANTAGES MasterTop 1200 should be conditioned at
 Easily applied. approximately 20°C.
 Seals porous substrates.
 Easily cleaned. MIXING / APPLICATION
 Good general chemical resistance. All porous concrete surfaces to be overlaid with
MasterTop 1210 or MasterTop 1230 must be
PACKAGING sealed with a coat of MasterTop 1200 with the
MasterTop 1200 is supplied in 12.4kg units. addition of 0.5ltr of MasterTop THN 2. Add the
MasterTop THN 2 to the base and reactor
TYPICAL PROPERTIES* components, after they have been decanted into
the mixing container, then mix the base and
reactor components together until all striations
Pot life @ 25°C 20 mins
have disappeared. Apply the mixed material to the
Mixed density @ 25°C 1.09kg/litre
Maximum service temp 60°C dry substrate at the rate of 6-8 m² / litre using a
Bond strength Greater than cohesive medium or short hair roller. Allow the sealer to
strength of good quality become completely tack free before over-coating
concrete with MasterTop 1210 or MasterTop 1230.

As a basecoat and sealer for MasterTop 1221A:

Basecoat: approx. 0.15-0.2kg/m²
Sealer: approx. 0.15-0.3kg/m²
MasterTop® 1200

WATCHPOINT NOTE
MasterTop 1200 is suitable for application to Field service, where provided, does not constitute
smooth surfaces only. Coverage is dependent on supervisory responsibility. For additional
surface porosity and regularity. Rates given are information contact your local BASF
indicative only. representative.
BASF reserves the right to have the true cause of
YIELD any difficulty determined by accepted test
MasterTop 1200 standard pack of 12.4kg will methods.
yield 11.38 litres.
QUALITY AND CARE
All products originating from BASF’s Dubai, UAE
EQUIPMENT CARE
facility are manufactured under a management
Remove uncured MasterTop 1200 from tools and system independently certified to conform to the
equipment using MasterTop THN 2. requirements of the quality, environmental and
occupational health & safety standards ISO 9001,
STORAGE ISO 14001 and OHSAS 18001.
Store out of direct sunlight, clear of the ground on
pallets protected from rainfall. In tropical climates * Properties listed are based on laboratory controlled tests.

the product must be stored in an air conditioned ® = Registered trademark of the BASF-Group in many countries.
environment.

Failure to comply with the recommended storage

conditions may result in premature deterioration of
the product or packaging. For specific storage
advice consult BASF's Technical Services
Department.

SAFETY PRECAUTIONS
Request and refer to printed MSDS.

BASF_CC-UAE/Top_1200_11_98/v2/02_16
The technical information and application advice given in this BASF publication are based on the present state of
STATEMENT OF our best scientific and practical knowledge. As the information herein is of a general nature, no assumption can be
RESPONSIBILITY made as to a product's suitability for a particular use or application and no warranty as to its accuracy, reliability or
completeness either expressed or implied is given other than those required by law. The user is responsible for
checking the suitability of products for their intended use.

Field service where provided does not constitute supervisory responsibility. Suggestions made by BASF either
NOTE orally or in writing may be followed, modified or rejected by the owner, engineer or contractor since they, and not
BASF, are responsible for carrying out procedures appropriate to a specific application.

BASF Construction Chemicals UAE LLC

Disclaimer: the LRQA mark relates
P.O. Box 37127, Dubai, UAE to certified management system and
Tel: +971 4 8090800, Fax: +971 4 8851002 not to the product mentioned on this
www.master-builders-solutions.basf.ae datasheet
PRODUCT DATA SHEET
Sikafloor®-1207
(formerly MTop 1207)

High build, solvent-free epoxy coating for concrete floors

DESCRIPTION FEATURES
Sikafloor®-1207 is a two component, solvent- • Excellent wear and abrasion resistance
free epoxy floor coating system, which provides hard- • Solvent-free
wearing, abrasion-resistant flooring system. • Slip resistance finish available
• Easily applied
USES • Textured high gloss finish
• Good general chemical resistance
Sikafloor®-1207has good wear and abrasion resistance • Limited maintenance
and is suitable for use in many industrial applications. • Attractive and serviceable colours
It can be used as a surface coating where a hygienic
and high gloss appearance is required. Also, it can also
provide an anti-slip finish which is suitable for use in
wet areas.
• Pharmaceutical and other medical laboratory situ-
ations
• Food processing and production – including dairies,
bakeries, mills and confectioners
• Beverage production – including soft drinks manu-
facture
• Industrial and commercial kitchens
• Engineering – including aircraft hangars, car produc-
tion facilities and maintenance areas
• Warehouses – for installations with a medium fre-
quency and volume of traffic

PRODUCT INFORMATION
Packaging 5kg units.
Shelf life Up to 12 months if stored in unopened containers according to manufac-
turer’s instructions.
Storage conditions Store out of direct sunlight, clear of the ground, on pallets protected from
rainfall. Avoid excessive compaction and protect from extremes of temper-
atures. In tropical climates, the product must be stored in an air-condi-
tioned environment.
Colour Sikafloor®-1207 is available in a wide range of colours: light grey; mid grey;
dark grey; blue, beige and red.

Product Data Sheet

Sikafloor®-1207
September 2024, Version 02.01
020811000000002084

1/3
Density

TECHNICAL INFORMATION
Shore D Hardness 74 ASTM D2240

Compressive strength 60 N/mm2 7 days ASTM C579

85 N/mm2 ASTM D695

Flexural-strength 60 N/mm2 ASTM C579 after 7 days

85 N/mm2 ASTM D695

Tensile strength 15 N/mm2 ASTM C 307

30 Mpa ASTM D 638

Consumption Approximately 0.29-0.36kg/m²/coat at 200-250 microns DFT.

BASIS OF PRODUCT DATA APPLICATION

Ensure that the substrate is free from dust and build-
All technical data stated in this Product Data Sheet are ing debris and that the area has been secured to pre-
based on laboratory tests. Actual measured data may vent intrusion of dust, airborne
vary due to circumstances beyond our control. particles, insects, small animals, etc. Make sure that
windows and doors are closed.
ECOLOGY, HEALTH AND SAFETY To avoid colour deviation from one batch of the resin
to another, only use resins with the same batch num-
For information and advice on the safe handling, stor- ber in the same area.
age and disposal of chemical products, users shall Apply two coats of Sikafloor®-1207 by short/medium-
refer to the most recent Safety Data Sheet (SDS) con- haired roller and allow at least 18 hours but not more
taining physical, ecological, toxicological and other than 36 hours between coats.
safety-related data. The second coat should be applied at a right angle to
the first coat.
APPLICATION INSTRUCTIONS If the application of Sikafloor®-1207 is delayed more
than 16 hours at 40ºC and 36 hours at 20ºC after the
SUBSTRATE PREPARATION application of the primer, then the primer must be
All contamination must be removed and a sound, thoroughly abraded to give an adequate mechanical
clean substrate is exposed. key and solvent wiped.
Mechanical means of preparation (such as light grit Sikafloor®-1207 should be allowed to dry 24 hours pri-
blasting, high pressure water jetting or grinding) are or to receiving light traffic. Full cure is achieved after 7
preferred, followed by the removal of dust and other days.
loose debris, using an industrial vacuum. CLEANING OF EQUIPMENT
A clean prepared surface will ensure adhesion
between substrate and coating and will improve the Remove uncured Sikafloor®-1207 immediately from
long-term durability. tools and equipment, using solvent.
The ideal surface profile for the application of Sika-
floor®-1207 is the texture of medium grit sand paper. LOCAL RESTRICTIONS
Ensure that the concrete is at least 28 days old. Do not
apply if the moisture content of the concrete sub- Please note that as a result of specific local regulations
strates exceeds 4%. the performance of this product may vary from coun-
The surface over which the Sikafloor®-1207 is to be try to country. Please consult the local Product Data
laid must be flat and roughened. Sheet for the exact description of the application
fields.
MIXING
Pour the base and the reactor into a suitable mixing
vessel and mix using a slow speed drill with spiral mix-
ing paddle attached, until all striations have disap-
peared and a uniform colour is obtained.

Product Data Sheet

Sikafloor®-1207
September 2024, Version 02.01
020811000000002084

2/3
LEGAL NOTES
The information, and, in particular, the recommenda-
tions relating to the application and end-use of Sika
products, are given in good faith based on Sika’s cur-
rent knowledge and experience of the products when
properly stored, handled and applied under normal
conditions in accordance with Sika’s recommenda-
tions. In practice, the differences in materials, sub-
strates and actual site conditions are such that no war-
ranty in respect of merchantability or of fitness for a
particular purpose, nor any liability arising out of any
legal relationship whatsoever, can be inferred either
from this information, or from any written recom-
mendations, or from any other advice offered. The
user of the product must test the product’s suitability
for the intended application and purpose. Sika re-
serves the right to change the properties of its
products. The proprietary rights of third parties must
be observed. All orders are accepted subject to our
current terms of sale and delivery. Users must always
refer to the most recent issue of the local Product
Data Sheet for the product concerned, copies of which
will be supplied on request. It may be necessary to ad-
apt the above disclaimer to specific local laws and reg-
ulations. Any changes to this disclaimer may only be
implemented with permission of Sika® Corporate Legal
in Baar.

Sika Egypt
1st Industrial Zone (A)
Section #10, Block 13035
El Obour City, Egypt
TEL: +202 44810580
FAX: +202 44810459
egy.sika.com

Sikafloor-1207-en-EG-(09-2024)-2-1.pdf

Product Data Sheet

Sikafloor®-1207
September 2024, Version 02.01
020811000000002084

3/3
MasterTile® 30
Cementitious, polymer modified tile adhesive for marble, non-vitrified and vitrified tiles, glass
and porcelain mosaic

DESCRIPTION COMPOSITION
MasterTile 30 is a cement based tile adhesive for thin MasterTile 30 is a blend of Portland cement, and
or thick bed fixing of ceramic tiles in interior or exterior graded sand, reinforced with a high organic polymer
situations, especially those exposed to permanently wet content.
conditions.
TYPICAL PROPERTIES
Suitable substrates are concrete, sand cement screeds
and renders, plaster boards, gypsum fibre boards and
suitably prepared timber. Colours: Off white and Grey
Flash point: None
TYPICAL APPLICATIONS Plastic 2000kg/m³
density:
MasterTile 30 is the adhesive of choice for swimming
pools and may be used with confidence in all wet Yield: A 30kg bag mixed with 6 Iitres of
process applications including: abattoirs, shower rooms, water yields 18 Iitres of mixed
institutional kitchens, bathrooms, and decorative, high adhesive.
risk cladding. MasterTile 30 may be used to tile
directly onto glazed tile surfaces and is especially
recommended for non-porous or high density and glass STANDARDS
mosaics where it may be used to both fix and grout. BS 5980 Part 10 : 1980
ANSI A 118.1
Used in conjunction with MasterTile RSG 705, the ANSI A 118.4 (MasterTile 30 mixed with
system is suitable for use where chemical resistance or MasterTile A 200)
a high standard of hygienic quality is essential.

For extreme conditions such as vibration or temperature COVERAGE

extremes etc. MasterTile 30 can be mixed with
MasterTile A 200 instead of water.
Solid bed fixing: 3 - 6 mm depth
MasterTile 30 mixed with MasterTile A 200 is suitable 5.4kg - 10.8kg/m²
for fixing certain types of natural stone. Please consult Notched trowel: smooth surface 2kg/m²
Master Builders Solutions Technical Service Department
for advice.
APPLICATION PROCEDURE
Surfaces to be tiled, should be sound, dimensionally
ADVANTAGES stable, clean and free from loose laitance, paint, oil,
• Waterproof: immersion will not affect adhesion. grease, mould release agent and residual curing
• Non-slip. compound. It should be ensured that tiles are dry, and
free of contaminants that could impair adhesion.
• Ready for use - just add water.
• Thin or thick bed.
• Exceeds British Standard requirements.
• Extended open / wet time.
• High adhesive bond strength.

PACKAGING
MasterTile 30 is available in 30kg bags.

December 2020 Page 1 of 3

MasterTile® 30
SURFACE PREPARATION APPLICATION INSTRUCTIONS
Porous concrete, mortars, renders, plaster boards and Apply MasterTile 30 to a uniform thickness of 3mm
gypsum fibre boards should be primed with PCI Primer 6mm or sufficient to cover the studs or keys on the tile
Gisogrund to reduce suction. back; (on a working area of not more than 1m²). Solid
bed fixing is recommended for wet conditions and for
Timber surfaces should be checked to ensure rigidity ceramic and marble flooring tiles, and vertical heavy
and soundness to accept the additional loading without duty applications including decorative stone cladding. If
deflection. preferred, the MasterTile 30 can additionally be buttered
on the backs of the tiles to ensure full adhesive contact.
Provision must be made to ensure adequate ventilation For all other vertical application the adhesive bed should
beneath tiled timber flooring. Tongue and groove, be combed horizontally with a notched trowel to remove
parquet and sprung floorings must first be strengthened excess.
by screwing 12mm thick exterior grade plywood at
200mm centres onto the existing timber base. Tiles should be dry and fixed by pressing into place with
slight twisting motion, ensuring the tile back achieves full
Timber partition walls should be stiffened by screwing at contact with the adhesive.
200mm centres onto studding, in both directions.
Ceramic tiles should never be butt joined. Leave a
Timber surfaces should always be primed with minimum of 2mm around tiles. Adjustments to tiles
MasterCast 141 / CEMENT SLURRY. MasterCast 141 should only be made during the adhesives open wet
/ CEMENT SLURRY should only be applied after time.
MasterTile 30 has been mixed, to ensure adhesive is
ready to apply immediately onto wet primer. Remove excess adhesive from the face of the tile with a
damp sponge or cloth before it sets. Similarly, joints
must be raked out in readiness for grouting.
MIXING INSTRUCTIONS Leave for a minimum of 24 hours before grouting. Select
Add MasterTile 30 to cool, clean water at the following the appropriate grout for joint size and in service use
rates: from the MasterTile range of products.

By weight 5:1 by volume approximately 2.5:1, mix to a

uniform lump free consistency and allow to stand for 5
WATCHPOINTS
minutes before use. Full bag volumes should be mixed Movement joints should be provided in accordance with
in a forced action mixer. Part bags should preferably be normal practice. Refer to published local standards or
mixed using a slow speed drill and mixing paddle. BS 5385.

MasterTile 30 should not be used on painted or metal

surfaces. The use of chilled mixing water will extend
open wet time in high ambient temperatures.

Gypsum plaster boards and surfaces, must be subjected

to pre-treatment. Please consult Master Builders
Solutions 's Technical Services Department for advice.

STORAGE
Store out of direct sunlight, clear of the ground on
pallets protected from rainfall. Avoid excessive
compaction.

December 2020 Page 2 of 3

 MasterTile® 30
SAFETY PRECAUTIONS
As with all chemical products, care should be taken
during use and storage to avoid contact with eyes
mouth, skin and foodstuffs. Treat splashes to eyes and
skin immediately. If accidentally ingested, seek
immediate medical attention. Reseal containers after
use. For further information, refer to material safety data
sheet.
NOTE
Field service, where provided, does not constitute
supervisory responsibility. For additional information
contact your local Master Builders Solutions
representative.

Master Builders Solutions reserves the right to have the

true cause of any difficulty determined by accepted test
methods.

QUALITY AND CARE

All products manufactured by Master Builders Solutions
Egypt, or imported from Master Builders Solutions
affiliate companies world- wide, are manufactured to
procedures certified to conform to the quality,
environment, health & safety management systems
described in the ISO 9001:2015, ISO 14001:2015 &
OHSAS 18001:2007 standards.

* Properties listed are based on laboratory controlled tests.

® Registered trademark of a MBCC Group member
in many countries of the world

Master_Builders_Solutions_CC-EG/Tile 30_09_11/v1/05_14

MBS Construction Chemicals Egypt (S.A.E), Business Park A, Building A1, Cairo Festival City, Ring Road, New Cairo, Egypt
Hotline: 15560, Phone: +202 2128 7800, Fax: +202 2128 7801
Website: https://www.master-builders-solutions.com/en-eg

December 2020 Page 3 of 3

 MasterTile® 530
Coloured, latex modified grout for ceramic tiles

DESCRIPTION STORAGE
MasterTile 530 is a fine coloured powder which, when Store out of direct sunlight, clear of the ground on pallets
mixed with water, gives a smooth, easily applied creamy protected from rainfall. Avoid excessive compaction.
paste for clean grouting of ceramic tiles. It sets to a
decorative water resistant finish. SAFETY PRECAUTIONS
As with all chemical products, care should be taken during
ADVANTAGES use and storage to avoid contact with eyes, mouth, skin
• Water-resistant (suitable for swimming pools). and foodstuffs (which may also be tainted with vapour
• Available in a range of colours. until product is fully cured). Treat splashes to eyes and
skin immediately. If accidentally ingested, seek immediate
• Resistant to cracking in joints up to 4mm wide. medical attention. Reseal containers after use.
• Ideal for internal and exterior applications.
• Formulated for Middle East conditions.
NOTE
Field service, where provided, does not constitute
PACKAGING supervisory responsibility. For additional information
MasterTile 530 is available in 15kg sacks. contact your local Master Builders Solutions
representative. Master Builders Solutions reserves the
COMPOSITION right to have the true cause of any difficulty determined by
accepted test methods.
MasterTile 530 is a blend of hydrophobic cement, fillers
and organic additives.

STANDARDS
BS 5980 - Cementitious Adhesives and Grouts ANSI 118.7
(Polymer Modified Cement Grouts)

APPLICATION PROCEDURES
Allow at least 24 hours between fixing tiles and grouting.
Mix grout powder with water to give a smooth, thick
consistency.
Gauging water for 15 kg sack is approx. 3.9 - 4.3 ltr.
Leave to stand for 15 minutes before using. Apply to tile
joints with a squeegee, brush or sponge. Remove surplus
grout with a damp sponge. When grouting is completed,
polish tiles with a dry cloth.

WATCHPOINTS
Certain types of tile may stain when in contact with
coloured cement grouts, it is therefore advisable to
consult the tile manufacturer and carry out trials before
use.

COVERAGE
1 kg is sufficient for approximately 4 square metres using
standard 150 x 150mm tiles.

December 2020 Page 1 of 2

 MasterTile® 530

QUALITY AND CARE

All products manufactured by Master Builders Solutions
Egypt, or imported from Master Builders Solutions affiliate
companies world- wide, are manufactured to procedures
certified to conform to the quality, environment, health &
safety management systems described in the ISO
9001:2015, ISO 14001:2015 & OHSAS 18001:2007
standards.

* Properties listed are based on laboratory controlled tests.

® Registered trademark of a MBCC Group member in

many countries of the world

Master_Builders_Solutions_CC-EG/Tile_530_09_12/v1/05_14

MBS Construction Chemicals Egypt (S.A.E), Business Park A, Building A1, Cairo Festival City, Ring Road, New Cairo, Egypt
Hotline: 15560, Phone: +202 2128 7800, Fax: +202 2128 7801
Website: https://www.master-builders-solutions.com/en-eg

December 2020 Page 2 of 2