Specifications Startup Compensation Timer Function[PA 2 : STaT]

PANEL METER Model

Power supply
MT4W- -4
100-240VAC 50/60Hz
MT4W-
12-24VDC
-1 This time function limits the operation of an output until the measured input (overvoltage or inrush current) is stable at
moment of power on. All outputs are off during startup compensation time setting after power is supplied.

MT4W SERIES Allowable voltage range90 to 110% Setting range: 00.0 to 99.9 (Unit: sec.), Factory default: 00.0
Power consumption 5VA 5W
Display method 7 Segment LED display (red) (Character height: 14.2mm) Parameter
INSTRUCTION MANUAL Display accuracy
23℃±5℃ - DC Type: F.S.±0.1% rdg±2digit / AC Type: F.S.±0.3% rdg±3digit
DC/AC Type: F.S.+0.3% rdg +3digit max. only for 5A terminal
Parameter Display Function Note
IN-T Input type Selectable RMS/AVG in AC type Available AC type only.
-10℃ to 50℃ - DC/AC Type: F.S.±0.5% rdg±3digit
IN-R Input range Selection of input range -
Input DC Voltage/Current, AC Voltage/Current, AC Frequency
DISP Display Selection of display type Setting range: STND, SCAL, FREQ
Max. allowable input 110% for each measured input range
A/D conversion method Practical over sampling using successive approximation ADC. STND Standard Standard scale range Display Max. display value of STND
Sampling cycle DC type: 50ms, AC type: 16.6ms FREQ Frequency Frequency display Available AC type only.
Max. indication range -1999 to 9999 (4digit) SCAL Scale Scale range These are displayed at SCAL
• Relay output - Contact capacity: 250VAC 3A, 30VDC 3A/Contact composition: N.O (1a) H-SC High scale Set max. value of display range It sets max. display value/min. display value
Preset output PA1 (-1999 to 9999)
• NPN/PNP Open Collector output - 12-24VDC ±2V 50mA Max. (Load resistance) (Parameter 1) L-SC Low scale Set min. value of display range
• RS485 communication output - Baud rate:1200/2400/4800/9600, Communication method : 2-wire half It is dispayed at SCAL /FREQ only and set
DOT Dot Set decimal point position the decimal point position
Sub output duplex,Synchronous method: Asynchronous method , Protocol : Modbus type
Correct High-limit value STND/ SCAL: Correction range 0.100 to 5.000
Thank you for choosing our Autonics products. (Transmission output) • Serial/BCD output - NPN Open collector output, 12-24VDC Max. 50mA (Resistive load) INbH Input bias high of display value FREQ: Correction range 0.100 to 9.999
• DC4-20mA output - Resolution: 12,000 division (Load resistance max. 600Ω), Response time:Max. 450ms
Please read the following safety considerations before use. Insulation resistance Min. 100MΩ (at 500VDC megger) between external terminal and case Correct Low-limit value
INbL Input bias low of display value Setting range: -99 to +99
Dielectric stength 2,000VAC for 1minute between external terminal and case
Input bias Set display index of
Setting range: 10-2, 10-1, 100, 101
Safety Considerations Noise stength ±2kV the square wave noise (pulse width: 1㎲) by the noise simulator
Mechanical 0.75mm amplitude at frequency of 10 to 55Hz (for 1 min.) in each X, Y, Z direction for 2 hours
INbE exponent frequency mode
Vibration Set operation mode of Setting range: OFF, lST, hST, LhST,
Malfunction 0.5mm amplitude at frequency of 10 to 55Hz (for 1 min.) in each X, Y, Z direction for 10 min. OUtT Out type
※Please observe all safety considerations for safe and proper product operation to avoid hazards. preset output HhST, LlST, LdST
Mechanical 100m/s² (approx. 10G) in each X, Y, Z direction for 3 times HYS Hysteresis Set hysteresis value Setting range: 1 to 10% F.S.
Shock
※Safety considerations are categorized as follows. Malfunction 300m/s² (approx. 30G) in each X, Y, Z direction for 3 times Startup compen
Mechanical Min. 20,000,000 operations STaT -sation time Set startup compensation time. Setting range: 00 to 99.9sec.
Warning Failure to follow these instructions may result in serious injury or death. Relay
life cycle Malfunction Min. 100,000 operations (250VAC 3A Load current) Set monitoring delay time
Caution Failure to follow these instructions may result in personal injury or product damage. Ambient PEkT Peak time for peak value (sec)
Setting range: 00 to 30sec.
-10 to 50℃, Storage: -20 to 60℃
Environ temperature Setting range: 0.1 to 5.0 sec.
※The symbols used on the product and instruction manual represent the following -ment Ambient DIsT Display time Set sampling time (sec.) (Variable by 0.1sec.)
symbol represents caution due to special circumstances in which hazards may occur. 35 to 85%RH, Storage: 35 to 85%RH
humidity Set usage of front side zero NO: Not use front side zero adjustment key
Double insulation or reinforced insulation PA2 ZERO Zero Key adjustment key YES: Use front side zero adjustment key
Insulation type (Parameter 2)
Warning (Mark: , dielectric strength between the measuring input part and the power part: 1kV)
Set external terminal (6, 7) HOLD: Use external terminal as Hold terminal
Approval EVIN Event Input function ZERO: Use external terminal as zero point
1. Fail-safe device must be installed when using the unit with machinery that may cause serious injury or ※1 adjustment terminal
Weight Approx. 326g (approx. 211g )
substantial economic loss. (e.g. nuclear power control, medical equipment, ships, vehicles, railways, Set the upper value output
※1: The weight includes packaging. The weight in parentheses is for unit only. FS-H Full scale High point or PV output Min. set range: Min. 10% F.S.
aircraft, combustion apparatus, safety equipment, crime/disaster prevention devices, etc.)
Failure to follow this instruction may result in personal injury, fire, or economic loss. ※ Environment resistance is rated at no freezing or condensation. Set the lower value output
FS-L Full scale Low point or PV output Max. set range: Max. FS-H 10%
2. The unit must be installed on a device panel before use.
Failure to follow this instruction may result in electric shock. Specification Of Measured Input And Range [PA 1: IN-R] ADRS Address Set communication address Setting range: 01 to 99
3. Do not connect, repair, or inspect the unit while connected to a power source. BPS Bit per second Set baudrate (bps) Setting range: 1200, 2400, 4800, 9600
Measured input Input
Failure to follow this instruction may result in electric shock. Type Display range [SㅊTㅍㅀㄷㄳㅅNㅜㅜD] Prescale Display range [SCAL] LOC Lock Set lock function Setting range: OFF, LOC1, LOC2, LOC3
and range impedance
4. Do not disassemble or modify the unit. Please contact us if necessary. hSET High set Set High setting value Setting range can be set within the display
0-500V [ 500V] 4.33MΩ 0.0 to 500.0 (fixed)
Failure to follow this instruction may result in electric shock or fire. lSET Low set Set Low setting value range of STND/ SCAL
0-100V [100V] 4.33MΩ 0.0 to 100.0 (fixed) PA 0
5. Check the terminal numbers before connecting the power source and measurement input. (Parameter 0) hPEK High peak Max. value by data monitoring
0-50V [ 50V] 433.15kΩ 0.00 to 50.00 (fixed) Initializes the monitored data value by
Failure to follow this instruction may result in fire. pressing any one of keys.
0-10V [10V] 433.15kΩ 0.00 to 10.00 (fixed) lPEK Low peak Min. value by data monitoring
DC Volt DOT Display range
Caution 0-5V [ 5V] 43.15kΩ 0.000 to 5.000 (fixed)
1. Do not use the unit outdoors. 0-1V [1V] 43.15kΩ 0.000 to 1.000 (fixed)
0 -1999 to 9999 Parameter Setting Parameter 0
)0 -199.9 to 999.9 RUN ※Press key in RUN mode and it
Failure to follow this instruction may result in electric shock or shorten the life cycle of the unit. 0-250mV [ )25V] 2.15kΩ 0.0 to 250.0 (fixed) RUN
)00 -19.99 to 99.99 key 3 sec. enters PA 0 group.
2. When connecting the power input and relay output cables, use AWG20 (0.05mm2) cables and make sure to 0-50mV [ 50MV] 2.15kΩ 0.00 to 50.00 (fixed) key
※Press key for over 3 sec. in key touch
tighten the terminal screw bolt above 0.74N.m to 0.90N.m. 0-5A [ 5A] 0.01Ω 0.000 to 5.000 (fixed) )000 -1.999 to 9.999 key 3 sec.
RUN mode, it displays [PA1]. Set preset High-limit value. (It is not displayed
Failure to follow this instruction may result in fire due to contact failure. 0-2A [ 2A] 0.01Ω 0.000 to 2.000 (fixed)
PA0 PA1 ※Press key for over 5 sec. in RUN hSET when OUtT mode value of PA2 is OFF)
(Display range is variable according ※Change the value with keys.
3. Use the unit within the rated specifications. 0-500mA [ )5A] 0.1Ω 0.0 to 500.0 (fixed) to decimal point position.)
key
key 2 sec. mode, it displays [PA2] after [PA1].
Failure to follow this instruction may result in electric shock or shorten the life cycle of the unit. PA2 When pressing key continually, Set preset Low-limit value. (It is not displayed
DC 0-200mA [ )2A] 0.1Ω 0.0 to 200.0 (fixed) key 3 sec. it stops displaying at [PA2]. when OUtT mode value of PA2 is OFF)
4. Do not use loads beyond the rated switching capacity of the relay contact. lSET
Ampere 0-50mA [ 50MA] 1.0Ω 0.00 to 50.00 (fixed) ※It is advanced to current display parameter releasing ※Change the value with keys.
Failure to follow this instruction may result in insulation failure, contact failure, contact bonding, relay damage, or fire. ※Please wire the proper terminal to its
5. Do not use water or oil-based detergent when cleaning the unit. Use dry cloth to clean the unit. 4-20mA [ 4-20] 1.0Ω 4.00 to 20.00 (fixed) key at [PA1] or [PA2]. It displays High-limit monitoring value
max. input within 30 to 100% of the ※Press key for over 3 sec. in any parameter groups, it (High peak) in RUN mode.
Failure to follow these instructions may result in electric shock or fire. 0-5mA [ 5MA] 10.0Ω 0.000 to 5.000 (fixed) hPEK
input terminal. returns to RUN mode. It is initialized by pressing any one of
6. Do not use the unit where flammable or explosive gas, humidity, direct sunlight, radiant heat, vibration, 0-2mA [ 2MA] 10.0Ω 0.000 to 2.000 (fixed) ※If any key is not entered for 60 sec. in each parameter, it
When it is higher than input, it may keys.
and impact may be present. 0-500V [ 500V] 4.98MΩ 0.0 to 500.0 (fixed) cause terminal breakdown and HHHH returns to RUN mode.
It displays High-limit monitoring value
Failure to follow this instruction may result in fire or explosion. 0-250V [ 250V] 4.98MΩ 0.0 to 250.0 (fixed) appears. The accuracy is decreased ※After returning to RUN mode, press key within 2 (Low peak) in RUN mode.
sec., it returns to previous parameter. (Refer to the below
lPEK
7. Keep dust and wire residue from flowing into the unit. 0-110V [110P] 1.08MΩ 0.0 to 440.0 (fixed) when it is connected to the terminal It is initialized by pressing any one of
Failure may result in fire or product malfunction. descriptions of each parameter group.) keys.
0-50V [ 50V] 1.08MΩ 0.00 to 50.00 (fixed) under 30%. ※PA 0 group cannot be entered when preset output mode of
8. Check the polarity of the measurement input contact before wiring the unit. AC Volt ※If PEK.T of Parameter2 is set as '00 S',
0-20V [ 20V] 200kΩ 0.00 to 20.00 (fixed) [PA2] group is OFF.
Failure to follow this instruction may result in fire or explosion. hPEK and lPEK are not displayed.
0-10V [10V] 200kΩ 0.00 to 10.00 (fixed)
※In case of 0 to 110V [110P] of
Front Panel Identification Panel Cut-Out
0-2V
0-1V
[ 2V]
[1V]
20kΩ
20kΩ
0.000 to 2.000 (fixed)
0.000 to 1.000 (fixed)
AC voltage range and using Parameter 1
P.T (potential transformer) for RUN Item Range of measured input
0-5A [ 5A] 0.01Ω 0.000 to 5.000 (fixed) 440V/110VAC, if 110V is input,
1. HI: High output indication of preset Min. 116 key for 3 sec. MT4W-DV 500V 100V 50V 10V 5V 1V )25V 50MV 500V
1 0-2.5A [ @5A] 0.01Ω 0.000 to 2.500 (fixed) and the unit displays 440V
2 GO: GO output indication of preset PA1 MT4W-DA 5A 2A )5A )2A 50MA 4-20 5MA 2MA 5A
2 6 0-1A [1A] 0.05Ω 0.000 to 1.000 (fixed) automatically by preset scale
3 LO: Low output indication of preset 45 +0.6 AC
3 -0 0-500mA [ )5A] 0.1Ω 0.0 to 500.0 (fixed) value for P.T user's convenient. MT4W-AV 500V 250V 110P (※) 50V 20V 10V 2V 1V 500V
4. : MODE Key Ampere Select measured input specification.
Min. 52.0 0-250mA [ )25A] 0.1Ω 0.0 to 250.0 (fixed) ㅑIN-R - Refer to " Specification Of MT4W-AA 5A @5A 1A )5A )25A )1A 50MA 5A
5. : Control key
92 +0.8 0-100mA [ )1A] 0.5Ω 0.0 to 100.0 (fixed) Measured Input And Range". ※110P is standard specification of 440/110P.T.
6. Unit label part -0
4 5
(Unit:mm) 0-50mA [ 50MA] 0.5Ω 0.00 to 50.00 (fixed) Select the display method of measuring input.
※There are no 1, 2, 3 output indication in Indication type. DISP Setting range: STND, SCAL, FREQ.
- Refer to " Specification Of Measured Input And Range". (FREQ mode is only for AC measuring type.)
Display Cycle Delay Function [PA 2 : DIsT]
Terminal Connection In some applications the measured input may fluctuate which in turn causes the display to fluctuate. By adjusting the IN-T Select measurement method when it is AC input.
Setting range: AUG, RMS (Average: AVG/Root mean square: RMS)
● MT4W-DV- ● MT4W-DA- display cycle delay function time at DIS.T of parameter 2, the operator can adjust the display time within a range of 0.1
sec to 5 sec. For example, if the operator sets the display cycle time to 4.0 sec., the display value displayed will be
When DISP is STND When DISP is SCAL When DISP is FREQ
1 2 3 4 5 6 7 8 9 1 2 3 4 5 6 7 8 9 the average input value over 4 sec. and also will show any changes if any every 4 sec.
It shows [Link] Set decimal point position. Set frequency measured range
STND DOT Setting range: DOT (Refer to " AC Frequency
250mV/50mV

5V/1V HOLD/
+ -
5mA/2mA
50mA/4-20mA
HOLD/
+ - Monitoring Max./Min. Initialization Function
value of standard
specification. 0, )0, )00, )000 Measurement Function Part".)
50V/10V
500V/100V
ZERO SOURCE
12-24VDC 5W
500mA/200mA
5A/2A
ZERO SOURCE
12-24VDC 5W
Display Value Function This function is to initialize parameter as factory difault.
Display value is fixed.
H-SC
Set display value for max.
input of measured input
100-240VAC COM
COM
50/60Hz 5VA
100-240VAC
50/60Hz 5VA [PA 0: hPEK/lPEK,PA 2: PEkT] RUN
● MT4W-AV- ● MT4W-AA- It monitors Max./Min. display value based on the current Set display value for min.
Press + + for over 5 sec. L-SC input of measured inputc
displays value and then displays the data at hPEK, lPEK of
1 2 3 4 5 6 7 8 9 1 2 3 4 5 6 7 8 9 parameter 0. Set the delay time (0 to 30 sec.) at PEkT of INIT NO YES
2V/1V parameter 2 in order to prevent malfunction caused by initial Adjust High-limit display Adjust High-limit display
100mA/50mA
INbH value gradient for max. input. INbH value gradient for max. input.
20V/10V HOLD/
+ - 500mA/250mA HOLD/ + - over current or over voltage, when monitoring the peak value.
1A SOURCE Setting range: )100 to %000 Setting range: )100 to (999
110V/50V ZERO SOURCE ZERO Delay time is 0 to 30 sec. and it starts to monitor the peak YES
500V/250V 12-24VDC 5W 12-24VDC 5W
5A/2.5A COM value after the set time. When pressing any one of ※Flash twice Adjust Low-limit display
COM 100-240VAC 100-240VAC Set index for frequency display
50/60Hz 5VA key at hPEK, lPEK of parameter 0, the monitored data is MT4W-DV/AV 500V in order and INbL value deviation fot min. input. INbE Setting range:10-2,
50/60Hz 5VA
Setting range: -99 to 99 10-1, 10-0, 10 1
<Option> initialized. it returns to
MT4W-DA/AA 5A RUN mode.
● Relay output+Current output[MT4W- - 0] ● Relay output[MT4W- - 1] ※Monitoring function is not displayed when the delay time is
MAIN OUT MAIN OUT set as "00 S" at PEkT of parameter 2.
CONTACT OUT:250VAC 3A 1a
RESISTIVE LOAD
DC4-20mA
Load 600Ω Max.
CONTACT OUT:250VAC 3A 1a
RESISTIVE LOAD Parameter 2 Change The Parameter
10 11 12 13 14 15 10 11 12 13 14 15 Current Output (DC4-20mA) AC Frequency Measurement RUN Setting Value
HI GO LO
Scale adjustment function Function [PA1 : DISP] key 5 sec. 1. Advance to the parameter to be changed when
mA
It measures input signal frequency when it is AC input. pressing key continuously in RUN mode
HI GO LO COM
[PA 2 : FS-H/ FS-L] It uses fixed decimal point[PA1:DOT], measured range
PA2
and releasing key at the parameter.
● NPN Open Collector output+BCD output[MT4W- - 2] ● PNP open collector output+BCD output[MT4W- - 3] It sets current output for the display value at the current output can be changed by setting and measured range of Select Preset output mode. (Refer to " Parameter Setting")
DC 4-20mA. decimal point position is as below chart. OUtT Setting range: OFF, lST, hST, LhST, HhST, LlST, LdST
2 4
6 8 10 12 14 16 18 20 2 4
6 8 10 12 14 16 18 20
+24VDC B D D1 D3 DOT COM2 Main Out +24VDC B D D1 D3 DOT COM2 Main Out It sets display value for 4mA at FS-L and 20mA at FS-H It is available to adjust the upper gradient at [PA1:INbH] Refer to " Preset Output Mode" 2. When pressing key in each parameter,
GO GO and the range between FS-H and FS-L should be 10% F.S.
30mA Max. BCD OUT (NPN Open 30mA Max. BCD OUT (PNP Open and [PA1:INbE]. In order to measure frequency the initial mode of the parameter is displayed.
(NPN OPEN COLLECTOR) Collector) (NPN OPEN COLLECTOR) Collector) (When it sets as under 10% F.S., it changed as over 10% F.S. normally, input signal, over 10% F.S. of measured range HYS Set preset hysteresis. within 10% of F.S.
But, it is not displayed when OUtT mode is OFF. (Refer to the description of each parameter.)
12-24VDC Max. 50mA 12-24VDC 12-24VDC Max. 50mA 12-24VDC automatically.) Preset display value is fixed to output as 4mA at should be supplied. Please select the proper point of
COM1 HI LO 0V A C D0 D2 POL Max. 50mA COM1 HI LO 0V A C D0 D2 POL Max. 50mA measurement terminal.
under FS-Land 20mA at over FS-H. 3. When pressing one of , , keys in display
1 3 5 7 9 11 13 15 17 19 1 3 5 7 9 11 13 15 17 19
Output ① Measured range Set startup compensation time.
STaT Setting range: 00 to 99.9sec. mode, the saved setting value is displayed.
● NPN open collector output+Current output[MT4W- - 4] ● PNP Open Collector output+Current output[MT4W- - 5] 20mA Decimal point Ex) Setting
0.000 0.00 0.0 0 The saved
position value
Set monitoring delay time. setting value
2 4 6
8 10 12 14 16 18 20 2 4 6 8 10 12 14 16 18 20 Measurement 0.100 to 0.10 to 0.1 to 1 to PEkT Setting range: 00 to 30sec. flashes evey
Main Out Main Out range 9.999Hz 99.99Hz 999.9Hz 9999Hz
IN-R 250V
+24VDC +24VDC Press one 0.5 sec.
GO (NPN Open GO (PNP Open
30mA Max. DC4-20mA 30mA Max. Min. setting range
Collector)
DC4-20mA
Collector) 4mA ※Accuracy of frequency measurement: Below 1kHz, F.S.
Load 600Ω Max. Load 600Ω Max. 10% F.S. ±0.1rdg ±2digit. From 1kHz to 10kHz, F.S ±0.3rdg ±2digit. Set a display cycle. 4. Change the setting value by or key when
12-24VDC 12-24VDC DIsT Setting range: 0.1 to 5.0sec. setting value flashes.
COM1 HI LO 0V Max. 50mA COM1 HI LO 0V Max. 50mA ② INB.H : 00.100 to 9.999 [Gradient adjustment of high value]
Display value Ex) Change AC type measured input from
1 3 5 7 9 11 13 15 17 19 1 3 5 7 9 11 13 15 17 19 FS-L FS-H 1
③ INB.E : 10-2, 10-1, 10-0, 10 [Index adjustment of INB.H] Enable zero point adjustment by front key operation to 250V to 125V.
select YES. Setting Setting
● NPN Open collector output+Low speed serial output[MT4W- - 6] ● PNP open collector output+Low speed serial output[MT4W- - 7] ZEKY Press both
Error Correction Function Zero Adjustment Function + keys at the same time for 3sec.
The devication value is saved at INbL automatically. IN-R
value
250V
value
2 4 6 8 10 12 14 16 18 20 2 4 6 8 10 12 14 16 18 20
[PA 1 : INbH/ INbL] It adjusts the indication value of the optioanl configured Press one 125V
+24VDC POL CLOCK LATCH Main Out +24VDC POL CLOCK LATCH Main Out
Select either Hold input by No.6, 7 terminal or zero point
GO GO input value as zero by force, zero point error can be setting by external signal.
30mA Max. SERIAL OUT (NPN Open 30mA Max. SERIAL OUT (PNP Open It corrects display value error of measured input. EVIN
adjusted with 3 ways as below. HOLD: Display value holding, ZERO: Zero point
(NPN OPEN COLLECTOR) Collector) (NPN OPEN COLLECTOR) Collector) INB.L: ±99 [Adjust deviation of low value] adjustment by hold terminal.
12-24VDC Max. 50mA 12-24VDC 12-24VDC Max. 50mA 12-24VDC INB.H: 5.000 to 0.100 [Correct gradient (%) of high value] When zero point adjustment with front key and DISP
Max. 50mA Max. 50mA Hold terminal is finished normally, zero point Set high-limit value for DC 20mA output position of PV putput.
COM1 HI LO 0V COM2 DATA COM1 HI LO 0V COM2 DATA Diplay value= (Measured value × INB.H) + INB.L FS-H ※When changing input range and prescale mode, the
1 3 5 7 9 11 13 15 17 19 1 3 5 7 9 11 13 15 17 19 of measurement terminal is displayed and the 5. When confitming the setting value with
When the measured range is 0 to 500V, and the display setting values of FS-H, FS-L are changed automatically
adjusted value is saved at INbL automatically. key, the changed setting value flashes twice
range is 0 to 500.0. If the low display value is "1.2" to as max. and min. value of input range.
● NPN Open Collector output+RS485 output[MT4W- - 8] ● PNP open collector output+RS485 output[MT4W- - 9] Input correc Input external and enters into the next setting.
0V input, set -12 as the INbL value to display "0.0" by Operation Front side key FS-L Set low-limit value for 4mA output position of PV output.
-tion value signal
2 4 6 8 10 12 14 16 18 20 2 4 6 8 10 12 14 16 18 20 adjusting the offset of the low value.
+24VDC B (-) SG Main Out +24VDC B (-) SG Main Out The display value to the 500V measured input varies by 6. It returns RUN mode from parameter by
GO GO PA1: Direct Press , Short-circuit Set address of RS485 communication output.
30mA Max. (NPN Open 30mA Max. (PNP Open
adjusting the offset of the low value. If this display value is pressing key for 3 sec.
RS485 Collector) RS485 Collector) input correction key for 3sec. external Hold ADRS Setting range: 01 to 99
Description
12-24VDC 12-24VDC "501.0", calculate 500.0/501.0 (the desired display value/ value method at the at terminal no. 6, 7
COM1 HI LO 0V A (+) SG Max. 50mA COM1 HI LO 0V A (+) SG Max. 50mA the display value), and set the 0.998 correction value as the at INbL. RUN mode. over min. 50m.
Select baud rate of RS485 communication output.
1 3 5 7 9 11 13 15 17 19 1 3 5 7 9 11 13 15 17 19 INbH to display "500.0" by adjusting the gradient of the
high value. ※Refer to description " Error Correction Function", " Error
BPS Setting range: 9600, 4800, 2400, 1200 User Manual For
※The offset correction range of INbLis within -99 to 99 Display Function", " Parameter 2" for function and error. Communication
Time Chart Of Serial Output And BCD Output for D-0, D-1 digit regardless of dicimal point. LOC
Set key lock function and select from 4 kinds.
Setting range: OFF, LOC1, LOC2, LOC3 Visit our website ([Link]) to
BCD output (Negative logic) Serial output (Negative logic) Gradient Correction Function [PA 1 : INbH] Diplay value
(Example of gradient
OFF No key lock function LOC2 Parameter 1, 2 lock
LOC1 Parameter 1 lock LOC3 Parameter 0, 1, 2 lock
download the user manaul for communication of
MT series.
ta tw tb tw correction)
t : 7.8ms (Picture 1) 15.000
ta : 0.5ms
It corrects the gradient of prescale value and display value.
Digit signal t : 20ms
(Picture 1) Display value Y can be used as α, β times αY
Cautions During Use
Diplay value

tw : 5ms Latch 12.000

t ta tb ta : 0.05ms
Output data Data tb : 2.3ms against X input value by correction function[ INbH] and α time 9.000 Indication
tw : 5ms 1. Please use the terminal (M3.5, Max.7.2mm) when connectting the AC power supply.
t Clock used as correction function of max. display value[ H-SC]. Y 6.000 value for
Cn-1 Cn C1 tb : 4.95ms β time 2. Please use separated line from high voltage line or power line in order to avoid inductive noise.
measured
31.2ms Data Dn-1 Dn D1`
Adjustment range is 0.100 to 5.000 and multiply current βY 3.000 input Input 3. Please install power switch or circuit breaker in order to cut off the power supply.
gradient. 4. The switch or circuit breaker should be installed near by users for safety. Max.
1.000 value
D3 Data 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 Ex)Input:200mVDC, Display:3.000 for MT4W-DV type 7.2mm
0 X 0.2 0.4 0.6 0.8 1V 5. Be sure to avoid using this unit near by machinery making strong high frequency noise.
Digit D2 Output DP D C B A DP D C B A DP D C B A DP D C B A ①Select 0-1VDC (1V) for measured input in Parameter 1. Input value (High frequency welder & Sewing machine, High capacity SCR unit etc.)
signal D1 Clock ②S tandard specification in input: 0-1VDC and 1.000 6. When input applied, if "HHHH" or "LLLL" are displayed, it has some trouble with measuring input, please check the
D0 therefore it has to be 15.000[ H-SC] for 1VDC (Input) in Setting method H-SC L-SC INbH Note line after power off.
A Data H H L H H H H H L L L H H L H H H H H L H order to display 3.000 for DC200mV (Input). ① Unavailable 0.000 1.000 - 7. Noise inflowing from power line can cause serious ● Using line filter ● Using Varistor
H L H L ② 7.500 0.000 2.000 problem for D.P.M. (Digital Panel Meter) driving by
tw But it is unable due to setting range is 9.999 In this case, any Install it closely from D.P.M.
B AC power supply. Even though there is condenser for
H L L H ③In this case, please check below chart. ③ 5.000 0.000 3.000 setting methods
Data ta tb HI
Please set as INbH× H-SC = 15.000 ④ 3.750 0.000 4.000 display the same protecting noise between lines at primary side of power 110/
signal L H H H Latch ⑤ 3.000 0.000 5.000 display value. transformer, but it is very difficult to install protection 110/ D.P.M. INPUT
C D.P.M. 220VAC
Display 4 3 @ 1 components at small size product like D.P.M. Therefore, 220VAC LOW
D
dot
H
H
H
H
H
L
H
H
H
H
Preset Output Mode [PA 2 : OUtT] please noise absorber circuit such as line filter, varistor
in external lines when voltage failure occurs by power Earth ground
*When clock pulse change High to Low, Data will be output. relay, magnet S/W and high frequency equipment are
Display 4 3 @ 1 Mode Output operation Operation
operated in same line or surge occurs by spark of high ● Using Double shield wire ● Using Single shield wire
hSET voltage or thunder etc.
H HI HI
8. Input line:Shield wire must be used when the measured
Prescale Function [PA1 : H-SC/L-SC]
lSET
H: Hysterisis input line is getting longer in the place occurring lots of Vin D.P.M. Vin D.P.M.
noise. LOW LOW
This function is to display setting (-1999 to 9999) of particular High/Low-limit value in order to display High/Low-limit OFF No output
9. Allowable installation environment
value of measured input. GO ①If shall be used indoor ③Pollution Degree 2
If measured inputs are 'a' or 'b' and particular values are 'A' or 'B', it will display a=A, b=B as below graph. If it is equal or lower than Low setting value, LO output is ON.
Display Display Display Display Display Display
lST LO H If it is higher than Low setting value, GO output is ON. ②Altitude Max. 2000m ④Installation Catergory Ⅱ
value B value B value B value B value a b value A ※Failure to follow these instructions may result in product damage.
HI If it is equal or higher than High setting value, HI output is ON.
a b
A A
A hST GO
H
If it is equal or lower than High setting value, GO output is ON.
A
a b a b A
a b
a b B B
HI
LO output is ON when it is equal or lower than Low setting value. Major Products
Input value Input value Input value Input value Input value Input value H HI output is ON when it is equal or higher than High setting value. Photoelectric Sensors Temperature Controllers
LhST GO
GO output is ON when it is higher than Low setting value, and Fiber Optic Sensors Temperature/Humidity Transducers
LO H
lower than High setting value. Door Sensors SSR/Power Controllers
Error Display Function HI H LO output is ON when it is equal or higher than Low setting value.
Door Side Sensors Counters http: //[Link]
Area Sensors Timers
Display Description ※Error display is released HhST GO HI output is ON when it is equal or higher than High setting value. Proximity Sensors Panel Meters Trusted Partner In Industrial Automation
automatically when it is in the LO H GO output is ON when it is lower than Low/High setting value. Pressure Sensors Tachometer/Pulse (Rate) Meters
HHHH Flashes when measurement input is exceeded the [Link] input (110%) Rotary Encoders Display Units
HEADQUARTERS:
measured and display range. LO output is ON when it is lower than Low setting value. 18, Bansong-ro 513beon-gil, Haeundae-gu, Busan, South Korea,
LLLL Flashes when measuremnet input is exceeded the [Link] input (-10%) ※'LLLL' is displayed when the HI H Connector/Sockets Sensor Controllers

Flashes when display input is exceeded H-SC set value measured input is 4-20mA.
LlST GO HI output is ON when it is equal or lower than High setting value. Switching Mode Power Supplies 48002
D-HH LO H GO output is ON when it is higher than Low/High setting value. Control Switches/Lamps/Buzzers OVERSEAS SALES:
D-LL Flashes when display input is exceeded L-SC set value ※After flashing 'OVER' 2 times I/O Terminal Blocks & Cables #402-303, Bucheon Techno Park, 655, Pyeongcheon-ro,
when it exceeds the zero range, It is operated same with [Link] but LO output does not operated under Stepper Motors/Drivers/Motion Controllers Wonmi-gu, Bucheon, Gyeonggi-do, South Korea, 14502
F-HH Flashes when input frequency is exceeded the max. display value of measured range it returns to RUN mode. LdST GO initial Low setting value, and it is ON from under next Low setting value. Graphic/Logic Panels TEL: 82-32-610-2730 / FAX: 82-32-329-0728
LO H E-mail: sales@[Link]
OVER Flashes when it exceeds zero range (±99) If this is higher than Low setting value, GO output is ON. Field Network Devices
Laser Marking System (Fiber, Co₂, Nd: Yag)
※The above specifications are subject to change and some models may be discontinued without notice. ※ hSETis displayed according to the setting of output operation mode, when user sets "OFF", hSET/ lSETare not displayed. Laser Welding/Cutting System EP-KE-77-0009L