16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1
L L
K K
UPPER-AUX
ROOF/A-PILLAR CHANNEL
J J
MOLDED CORNER
UPPER AUX SEAL INSTALLATION: SEE DETAIL A
I 1 OR 2
UPPER AUX CHANNEL I
-BEGIN BY INSERTING THE X-MAS TREE FASTENER 1 OR 2
INTO THE CORRESPONDING HOLE IN THE A-PILLAR
COVER
-PUSH THE MOLDED CORNER UP INTO THE CORNER OF DETAIL A
SCALE 3:4
H H
DOOR OPENING AS SHOWN
-PUSH THE SEAL DOWN ONTO THE ROOF/A-PILLAR CHANNEL
STARTING AT EACH END AND FINISH IN THE MIDDLE
-PUSH THE B-PILLAR PORTION DOWN ONTO THE REAR CHANNEL
-PUSH THE "FOOTBALL" UNDER THE ROOF AND A-PILLAR EDGE UPPER-AUX
REAR CHANNEL
G G
F F
E E
ROOF EDGE
D D
GENERAL NOTES
1) FOR INSTALLATION OF DOORS ON KW AND PB 2.1M CABS
"FOOTBALL"
UPPER AUX CHANNEL
BULB
C C
OUTBOARD
R97-1554R
R97-1554
SECTION A-A
SCALE 3:1
1 1 3 R42-1165 SEAL - BODY MOUNTED SECONDARY NOTED
B B
1 2 R42-1115R SEAL - UPPER AUX NOTED
1 1 R42-1115 SEAL - UPPER AUX NOTED
QTY QTY ITEM PART NUMBER PRODUCT DESCRIPTION MATERIAL
1. THIS DRAWING AND THE INFORMATION CONTAINED HEREIN
TOLERANCES THIRD ANGLE PROJECTION
ARE PROPRIETARY TO PACCAR INC UNLESS OTHERWISE NOTED DRAWING REV
AND SHALL NOT BE REPRODUCED, COPIED OR DISCLOSED, UNLESS OTHERWISE SPECIFIED
IN WHOLE OR IN PART, OR USED FOR MANUFACTURE OR FOR
ANGLE = # 1
R97-1554 C
OTHER PURPOSE WITHOUT THE WRITTEN PERMISSION OF
PACCAR INC. (X) = # 1
2. DIMENSIONING AND TOLERANCING PER PACCAR CS0108. (X.X) = # 0.5 DO NOT SCALE DRAWING DIMENSION UNITS MILLIMETERS
3. REMOVE ALL BURRS. BREAK SHARP EDGES.
4. PART IDENTIFICATION AND TRACEABILITY REQUIREMENTS TITLE
A A
TO COMPLY WITH PACCAR CPS0098.
INSTALL - BODY MOUNTED DOOR SEALS
5. THIS DRAWING/SPECIFICATION USES SYMBOLS TO CLASSIFY
CHARACTERISTICS. THESE SYMBOLS ARE DEFINED IN THE
PACCAR SUPPLIER QUALITY STANDARD. SCALE 1:5
6. EMISSION-RELATED PART. CODE: N DWG
SEE PACCAR CPS0374 FOR REQUIREMENTS. DRAWING VERSION C.8 SHEET 1 OF 2 SIZE
A0
16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1
16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1
L L
K K
BODY MOUNTED SECONDARY SEAL INSTALLATION:
J 3 BODY MOUNTED SECONDARY CHANNEL J
-START THE SEAL AT THE BOTTOM REAR OF THE DOOR, MAKE SURE THE END IS ON THE
FLAT EDGE OF THE DOOR FRAME.
-PUSHING THE SEAL DOWN ONTO THE FLANGE WITH THE BULB FACING OUTBOARD,
WORK YOUR WAY AROUND THE DOOR OPENING
I I
-MAKE SURE TO PUSH THE SEAL UP INTO THE CORNERS AND TO LEAVE A MINIMAL
GAP BETWEEN THE TWO END OF THE SEAL
-ENSURE INTERIOR/INBOARD SEAL LIP IS ON TOP OF INTERIOR TRIM EDGE; IF NECESSARY,
PULL TRIM TEAR CORD ALONG PERIMETER OF SEAL TO PULL LIP ON TOP OF TRIM
H H
G G
FLANGE
F F
OUTBOARD
TRIM TEAR CORD
E E
SEAL TO ROOF INTERFACE BULB
SECTION A-A
SCALE 3:1
D D
C C
START HERE
B B
UNLESS OTHERWISE NOTED TITLE
INSTALL - BODY MOUNTED DOOR SEALS
THIS DRAWING AND THE
INFORMATION CONTAINED
HEREIN ARE PROPRIETARY
TO PACCAR INC.
IT SHALL NOT BE
REPRODUCED, COPIED OR DRAWING REV
A R97-1554 C A
DISCLOSED, IN WHOLE OR
IN PART, OR USED FOR
MANUFACTURE OR FOR
OTHER PURPOSE WITHOUT
THE WRITTEN PERMISSION DWG
OF PACCAR INC. SCALE 1:5 DRAWING VERSION C.8 SHEET 2 OF 2 SIZE
A0
16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1
