DRUM MOTOR

DM SERIES
DM 0080

Practice-oriented, scalable and thought out in detail: The new drum motor DM 0080
makes it easy to build a completely individual conveyor system and is dimensioned for
the higher requirements of permissible belt tension now demanded from industry and
belt manufacturers alike.

With a broader speed spectrum, the DM 0080 covers all possible applications. The
clever plug-and-play connection significantly simplifies the installation. Each motor is
approved, tested, and modularized so that it can be produced and delivered around
the world in the shortest amount of time.

The modular design of the DM 0080 allows a free combination of individual module
groups, such as shaft, end housing, shell, steel or technopolymer gear, asynchronous
or synchronous motor winding, to perfectly meet the requirements of an application. In
addition, various options, such as encoder, brake, backstop, rubber laggings, etc., as
well as different accessories are available.

With the platform concept of the DM 0080, it is possible to cover all internal logistics
applications in the food processing sector, as well as in industry, distribution and
airports.

The DM 0080 synchronous drum motor is also offered as oil-free variant. It is ideal for
highly dynamic applications, conveyor systems in food processing, SmartBelt
conveyors and many belt conveyors with servo driver.

© 12 | 2023 Interroll
42
 DRUM MOTOR
DM SERIES
DM 0080

Technical data

DL series
Asynchronous squirrel cage motor AC synchronous permanent magnet motor

Insulation class of motor windings Class F, IEC 34 (VDE 0530) Class F, IEC 34 (VDE 0530)

Voltage 230/400 V ±5 % (IEC 34/38) 230 or 400 V

Most of the common international voltages and
frequencies are available upon request

Frequency 50 Hz 200 Hz

Shaft sealing NBR NBR

Protection rate Motor* IP69K IP69K

Thermal controller Bi-metal switch Bi-metal switch

Operating mode S1 S1

DM series
Ambient temperature, 3-phase motor +2 to +40 °C +2 to +40 °C
Low temperature ranges on request Low temperature ranges on request

Ambient temperature, 3-phase motor for +2 to +25 °C +2 to +40 °C

applications with form-fit belts or no belt

* The protection rate of the cable connector may deviate.

Design variants and accessories

Laggings Lagging for friction drive belts

Lagging for modular plastic belts
Lagging for positive drive solid homogeneous belts

DP series
Transmission of force Sprockets

Options Backstop
Electromagnetic holding brake and rectifier*
Encoder*
Balancing
Plug connection*

Oils Food-grade oils (NSF H1)

Synchronous motors also available as oil-free variants

Certificate cULus safety certificates

Accessories Deflection drums; conveyor rollers; mounting brackets; cables; inverters

Application notes

A combination of encoder and safety holding brake is not possible. In addition, the use of a backstop with a synchronous motor is
technically not meaningful.

* Depending on the option, the drum motor is extended by 50 – 70 mm.

© 12 | 2023 Interroll
43
DRUM MOTOR
DM SERIES
DM 0080

Material variants
The following components can be selected for the drum motor and the electrical connection:

Component Version Aluminum Mild steel Stainless steel Brass/nickel Technopolymer

Shell Crowned l l
Cylindrical l l
Cylindrical + key for sprockets l l
End housing Standard l l
Shaft Standard l
Cross-drilled thread l
Gear boxes Planetary gear box l l
Electrical connector Straight connector l l l
Straight hygienic connector l
Elbow connector l l
Terminal box l l l
Straight plug connection l
90° plug connection l
90° hygienic connector l
Motor winding Asynchronous motor

Synchronous motor

External seal PTFE

© 12 | 2023 Interroll
44
 DRUM MOTOR
DM SERIES
DM 0080

Motor variants
Mechanical data for synchronous motors with steel gear

DL series
PN nP gs i v nA MA FN MMAX/MA FWMIN SLMIN
[W] [m/s] [min-1] [Nm] [N] [mm] [mm]

145 8 3 164.23 0.08 18.3 65.0 1594 1.4 211 204

145 8 3 119.83 0.11 25.0 47.4 1163 2.1 211 204

145 8 3 103.89 0.12 28.9 41.1 1009 2.5 211 204

145 8 3 85.34 0.15 35.2 33.8 828 3.0 211 204

145 8 2 62.7 0.20 47.8 26.0 637 2.2 192 185

145 8 2 53.63 0.24 55.9 22.2 545 2.5 192 185

145 8 2 42.28 0.30 71.0 17.5 430 3.0 192 185

DM series
145 8 2 38.5 0.33 77.9 15.9 391 3.0 192 185

145 8 2 31.35 0.41 95.7 13.0 319 3.0 192 185

145 8 2 26.94 0.48 111.4 11.2 274 3.0 192 185

145 8 2 20.27 0.63 148.0 8.4 206 3.0 192 185

145 8 2 14.44 0.89 207.8 6.0 147 3.0 192 185

145 8 2 11.23 1.14 267.1 4.6 114 3.0 192 185

145 8 1 8.25 1.55 363.6 3.6 88 3.0 192 185

145 8 1 4.71 2.72 636.9 2.1 51 3.0 192 185

298 8 2 53.63 0.24 55.9 45.9 1125 1.2 222 215

DP series
298 8 2 42.28 0.30 71.0 36.1 887 1.5 222 215

298 8 2 38.5 0.33 77.9 32.9 808 1.6 222 215

298 8 2 31.35 0.41 95.7 26.8 658 3.0 222 215

298 8 2 26.94 0.48 111.4 23.0 565 3.0 222 215

298 8 2 20.27 0.63 148.0 17.3 425 3.0 222 215

298 8 2 14.44 0.89 207.8 12.3 303 3.0 222 215

298 8 2 11.23 1.14 267.1 9.6 236 3.0 222 215

298 8 1 8.25 1.55 363.6 7.4 183 3.0 222 215

298 8 1 4.71 2.72 636.9 4.3 104 3.0 222 215

Application notes

© 12 | 2023 Interroll
45
DRUM MOTOR
DM SERIES
DM 0080

PN nP gs i v nA MA FN MMAX/MA FWMIN SLMIN

[W] [m/s] [min-1] [Nm] [N] [mm] [mm]
425 8 2 38.5 0.33 77.9 46.8 1148 1.2 252 245

425 8 2 31.35 0.41 95.7 38.1 935 2.5 252 245

425 8 2 26.94 0.48 111.4 32.7 803 3.0 252 245

425 8 2 20.27 0.63 148.0 24.6 604 3.0 252 245

425 8 2 14.44 0.89 207.8 17.5 431 3.0 252 245

425 8 2 11.23 1.14 267.1 13.6 335 3.0 252 245

425 8 1 8.25 1.55 363.6 10.6 260 3.0 252 245

425 8 1 4.71 2.72 636.9 6.0 148 3.0 252 245

550 8 2 31.35 0.41 95.7 49.4 1212 2.0 282 275

550 8 2 26.94 0.47 111.4 42.4 1041 2.3 282 275

550 8 2 20.27 0.63 148.0 31.9 783 2.9 282 275

550 8 2 14.44 0.89 207.8 22.7 558 3.0 282 275

550 8 2 11.23 1.14 267.1 17.7 434 3.0 282 275

550 8 1 8.25 1.55 363.6 13.7 337 1.9 282 275

550 8 1 4.71 2.72 636.9 7.8 192 3.0 282 275

PN = Rated power MA = Drum motor rated torque

nP = Number of poles FN = Drum motor rated belt pull
gs = Gear stages MMAX/MA = Ratio of max. acceleration torque to rated torque
i = Speed ratio FWMIN = Minimum drum width
v = Speed SLMIN = Minimum shell length
nA = Shell rated speed

© 12 | 2023 Interroll
46
 DRUM MOTOR
DM SERIES
DM 0080

Electrical data for synchronous motors

DL series
PN nP UN IN I0 IMAX fN η nN JR MN M0 MMAX RP LSD LSQ ke Te kTN USH
[W] [V] [A] [A] [A] [Hz] [1/min] [kgcm2] [Nm] [Nm] [Nm] [Ω] [mH] [mH] [V/krpm] [ms] [Nm/A] [V]

145 8 230 0.81 0.81 2.43 200 0.85 3000 0.46 0.46 0.46 1.38 21.6 45.6 53.7 41.57 4.97 0.57 4.37

145 8 400 0.47 0.47 1.41 200 0.83 3000 0.46 0.46 0.46 1.38 56.6 130.7 138.0 72.23 4.41 0.98 6.65

298 8 230 1.30 1.30 3.90 200 0.86 3000 0.92 0.95 0.95 2.85 10.2 27.8 29.3 47.46 5.75 0.73 3.32

298 8 400 0.78 0.78 2.34 200 0.87 3000 0.92 0.95 0.95 2.85 29.1 81.9 94.1 83.09 6.48 1.22 5.67

425 8 230 2.30 2.30 6.90 200 0.87 3000 1.38 1.35 1.35 4.05 5.66 16.3 19.4 45.81 6.86 0.59 3.25

425 8 400 1.32 1.32 3.96 200 0.86 3000 1.38 1.35 1.35 4.05 17.6 49.8 59.0 80.80 6.70 1.02 5.81

550 8 230 2.94 2.94 8.82 200 0.90 3000 1.84 1.75 1.75 5.25 3.89 10.2 11.8 38.45 6.06 0.59 2.86

550 8 400 1.70 1.70 5.10 200 0.90 3000 1.84 1.75 1.75 5.25 9.20 24.1 27.6 66.60 6.00 1.03 3.91

DM series
PN = Rated power MN = Rated torque of rotor
nP = Number of poles M0 = Standstill torque
UN = Rated voltage MMAX = Maximum torque
IN = Rated current RP = Phase to phase resistance
I0 = Standstill current LSD = d-axis inductance
IMAX = Maximum current LSQ = q-axis inductance
fN = Rated frequency ke = EMF (mutual induction voltage constant)
η = Efficiency Te = Electrical time constant
nN = Rated torque of rotor kTN = Torque constant
JR = Rotor moment of inertia USH = Heating voltage

Mechanical data for synchronous motors with oil-free steel gear

DP series
PN nP gs i v nA MA FN MMAX/MA FWMIN SLMIN
[W] [m/s] [min-1] [Nm] [N] [mm] [mm]

80 8 2 62.7 0.20 47.8 14.1 346 3.0 192 185

80 8 2 53.63 0.24 55.9 12.1 296 3.0 192 185

80 8 2 42.28 0.30 71.0 9.5 233 3.0 192 185

80 8 2 38.5 0.33 77.9 8.7 213 3.0 192 185

80 8 2 31.35 0.41 95.7 7.1 173 3.0 192 185

80 8 2 26.94 0.47 111.4 6.1 149 3.0 192 185

80 8 2 20.97 0.63 148.0 4.6 112 3.0 192 185

Application notes

80 8 2 14.44 0.89 207.8 3.2 80 3.0 192 185

80 8 2 11.23 1.14 267.1 2.5 62 3.0 192 185

80 8 1 8.25 1.55 363.6 2.0 48 3.0 192 185

80 8 1 4.71 2.72 636.9 1.1 27 3.0 192 185

110 8 2 53.63 0.24 55.9 16.9 415 3.0 222 215

110 8 2 42.28 0.30 71.0 13.3 327 3.0 222 215

110 8 2 38.5 0.33 77.9 12.1 298 3.0 222 215

© 12 | 2023 Interroll
47
DRUM MOTOR
DM SERIES
DM 0080

PN nP gs i v nA MA FN MMAX/MA FWMIN SLMIN

[W] [m/s] [min-1] [Nm] [N] [mm] [mm]
110 8 2 31.35 0.41 95.7 9.9 242 3.0 222 215

110 8 2 26.94 0.47 111.4 8.5 208 3.0 222 215

110 8 2 20.27 0.63 148.0 6.4 157 3.0 222 215

110 8 2 14.44 0.89 207.8 4.5 112 3.0 222 215

110 8 2 11.23 1.14 267.1 3.5 87 3.0 222 215

110 8 1 8.25 1.55 363.6 2.7 67 3.0 222 215

110 8 1 4.71 2.72 636.9 1.6 38 3.0 222 215

180 8 2 38.5 0.33 77.9 19.8 485 2.7 252 245

180 8 2 31.35 0.41 95.7 16.1 395 3.0 252 245

180 8 2 26.94 0.47 111.4 13.8 339 3.0 252 245

180 8 2 20.27 0.63 148.0 10.4 255 3.0 252 245

180 8 2 14.44 0.89 207.8 7.4 182 3.0 252 245

180 8 2 11.23 1.14 267.1 5.8 141 3.0 252 245

180 8 1 8.25 1.55 363.6 4.5 110 3.0 252 245

180 8 1 4.71 2.72 636.9 2.6 63 3.0 252 245

235 8 2 38.5 0.33 77.9 27.7 680 1.9 282 275

235 8 2 31.35 0.41 95.7 22.6 554 3.0 282 275

235 8 2 26.94 0.47 111.4 19.4 476 3.0 282 275

235 8 2 20.27 0.63 148.0 14.6 358 3.0 282 275

235 8 2 14.44 0.89 207.8 10.4 255 3.0 282 275

235 8 2 11.23 1.14 267.1 8.1 198 3.0 282 275

235 8 1 8.25 1.55 363.6 6.3 154 3.0 282 275

235 8 1 4.71 2.72 636.9 3.6 88 3.0 282 275

PN = Rated power MA = Drum motor rated torque

nP = Number of poles FN = Drum motor rated belt pull
gs = Gear stages MMAX/MA = Ratio of max. acceleration torque to rated torque
i = Speed ratio FWMIN = Minimum drum width
v = Speed SLMIN = Minimum shell length
nA = Shell rated speed

© 12 | 2023 Interroll
48
 DRUM MOTOR
DM SERIES
DM 0080

Electrical data for oil-free synchronous motors

DL series
PN nP UN IN I0 IMAX fN η nN JR MN M0 MMAX RP LSD LSQ ke Te kTN USH
[W] [V] [A] [A] [A] [Hz] [1/min] [kgcm2] [Nm] [Nm] [Nm] [Ω] [mH] [mH] [V/krpm] [ms] [Nm/A] [V DC]

80 8 230 0.45 0.45 1.35 200 0.85 3000 0.46 0.25 0.25 0.75 21.6 45.6 53.7 41.57 4.97 0.57 2.43

80 8 400 0.26 0.26 0.78 200 0.83 3000 0.46 0.25 0.25 0.75 56.6 130.7 138.0 72.23 4.41 0.98 3.68

110 8 230 0.48 0.48 1.44 200 0.86 3000 0.92 0.35 0.35 1.05 10.2 27.8 29.3 47.46 5.75 0.73 1.22

110 8 400 0.29 0.29 0.87 200 0.87 3000 0.92 0.35 0.35 1.05 29.1 81.9 94.1 83.09 6.48 1.22 2.11

180 8 230 0.97 0.97 2.91 200 0.87 3000 1.38 0.57 0.57 1.71 5.66 16.3 19.4 45.81 6.86 0.59 1.37

180 8 400 0.56 0.56 1.68 200 0.86 3000 1.38 0.57 0.57 1.71 17.6 49.8 59.0 80.80 6.70 1.02 2.46

235 8 230 1.30 1.30 3.90 200 0.92 3000 1.84 0.75 0.75 2.25 3.89 10.2 11.8 38.45 6.06 0.59 1.26

235 8 400 0.75 0.75 2.25 200 0.92 3000 1.84 0.75 0.75 2.25 9.2 24.1 27.6 66.60 6.00 1.03 1.73

DM series
PN = Rated power MN = Rated torque of rotor
nP = Number of poles M0 = Standstill torque
UN = Rated voltage MMAX = Maximum torque
IN = Rated current RP = Phase to phase resistance
I0 = Standstill current LSD = d-axis inductance
IMAX = Maximum current LSQ = q-axis inductance
fN = Rated frequency ke = EMF (mutual induction voltage constant)
η = Efficiency Te = Electrical time constant
nN = Rated torque of rotor kTN = Torque constant
JR = Rotor moment of inertia USH = Heating voltage

DP series
Application notes

© 12 | 2023 Interroll
49
DRUM MOTOR
DM SERIES
DM 0080

Mechanical data for 3-phase asynchronous motor with steel gear

PN nP gs i v nA MA FN FWMIN SLMIN
[W] [m/s] [min-1] [Nm] [N] [mm] [mm]

40 4 3 164.23 0.03 7.8 42.4 1040 219 212

40 4 3 119.83 0.05 10.7 30.9 759 219 212

40 4 3 103.89 0.05 12.3 26.8 658 219 212

40 4 3 85.34 0.06 15.0 22.0 541 219 212

40 4 2 62.70 0.09 20.4 16.9 416 200 193

40 4 2 53.63 0.10 23.8 14.5 356 200 193

40 4 2 42.28 0.13 30.2 11.4 281 200 193

40 4 2 38.50 0.14 33.2 10.4 256 200 193

40 4 2 31.35 0.17 40.8 8.5 208 200 193

40 4 2 26.94 0.20 47.4 7.3 179 200 193

40 4 2 20.27 0.27 63.0 5.5 135 200 193

75 2 3 164.23 0.07 16.2 38.1 936 219 212

75 2 3 119.83 0.10 22.2 27.8 683 219 212

75 2 3 103.89 0.11 25.6 24.1 592 219 212

75 2 3 85.34 0.13 31.2 19.8 486 219 212

75 2 2 62.70 0.18 42.4 15.2 374 200 193

75 2 2 53.63 0.21 49.6 13.0 320 200 193

75 2 2 42.28 0.27 62.9 10.3 252 200 193

75 2 2 38.50 0.30 69.1 9.4 230 200 193

75 2 2 31.35 0.36 84.8 7.6 187 200 193

75 2 2 26.94 0.42 98.7 6.5 161 200 193

75 2 2 20.27 0.56 131.2 4.9 121 200 193

75 2 2 14.44 0.79 184.1 3.5 86 200 193

75 2 2 11.23 1.01 236.8 2.7 67 200 193

© 12 | 2023 Interroll
50
 DRUM MOTOR
DM SERIES
DM 0080

PN nP gs i v nA MA FN FWMIN SLMIN
[W] [m/s] [min-1] [Nm] [N] [mm] [mm]

DL series
80 4 3 119.83 0.05 10.9 59.8 1467 269 262

80 4 3 103.89 0.05 12.6 51.8 1272 269 262

80 4 3 85.34 0.07 15.3 42.6 1045 269 262

80 4 2 62.70 0.09 20.9 32.7 804 250 243

80 4 2 53.63 0.10 24.4 28.0 687 250 243

80 4 2 42.28 0.13 30.9 22.1 542 250 243

80 4 2 38.50 0.15 34.0 20.1 494 250 243

80 4 2 31.35 0.18 41.7 16.4 402 250 243

80 4 2 26.94 0.21 48.6 14.1 345 250 243

DM series
80 4 2 20.27 0.28 64.5 10.6 260 250 243

80 4 2 14.44 0.39 90.6 7.5 185 250 243

80 4 2 11.23 0.50 116.5 5.9 144 250 243

80 4 1 8.25 0.68 158.5 4.5 112 250 243

80 4 1 4.71 1.18 277.7 2.6 64 250 243

140 2 3 119.83 0.10 23.0 50.5 1239 269 262

140 2 3 103.89 0.11 26.5 43.8 1074 269 262

140 2 3 85.34 0.14 32.3 36.0 883 269 262

140 2 2 62.70 0.19 43.9 27.7 679 250 243

140 2 2 53.63 0.22 51.3 23.7 580 250 243

DP series
140 2 2 42.28 0.28 65.1 18.6 458 250 243

140 2 2 38.50 0.31 71.5 17.0 417 250 243

140 2 2 31.35 0.38 87.8 13.8 339 250 243

140 2 2 26.94 0.44 102.2 11.9 292 250 243

140 2 2 20.27 0.58 135.8 8.9 219 250 243

140 2 2 14.44 0.81 190.7 6.4 156 250 243

140 2 2 11.23 1.05 245.1 5.0 122 250 243

140 2 1 8.25 1.42 333.7 3.8 94 250 243

Application notes

140 2 1 4.71 2.49 584.5 2.2 54 250 243

PN = Rated power nA = Shell rated speed

nP = Number of poles MA = Drum motor rated torque
gs = Gear stages FN = Drum motor rated belt pull
i = Speed ratio FWMIN = Minimum drum width
v = Speed SLMIN = Minimum shell length

© 12 | 2023 Interroll
51
DRUM MOTOR
DM SERIES
DM 0080

Mechanical data for 3-phase asynchronous motor with technopolymer gear

PN nP gs i v nA MA FN FWMIN SLMIN
[W] [m/s] [min-1] [Nm] [N] [mm] [mm]

40 4 3 78.55 0.07 16.3 20.3 498 239 232

40 4 3 71.56 0.08 17.9 18.5 454 239 232

40 4 3 63.51 0.09 20.1 16.4 403 239 232

40 4 3 52.92 0.10 24.1 13.7 336 239 232

40 4 3 48.79 0.11 26.2 12.6 309 239 232

40 4 3 43.3 0.13 29.5 11.2 275 239 232

40 4 2 19.2 0.28 66.6 5.2 128 239 232

40 4 2 16 0.34 79.9 4.3 106 239 232

40 4 2 13.09 0.42 97.6 3.5 87 239 232

75 2 3 78.55 0.14 33.9 18.2 448 239 232

75 2 3 71.56 0.16 37.2 16.6 408 239 232

75 2 3 63.51 0.18 41.9 14.7 362 239 232

75 2 3 52.92 0.21 50.2 12.3 302 239 232

75 2 3 48.79 0.23 54.5 11.3 278 239 232

75 2 3 43.3 0.26 61.4 10.1 247 239 232

75 2 2 19.2 0.59 138.5 4.7 114 239 232

75 2 2 16 0.71 166.2 3.9 95 239 232

75 2 2 13.09 0.87 203.1 3.2 78 239 232

PN = Rated power nA = Shell rated speed

nP = Number of poles MA = Drum motor rated torque
gs = Gear stages FN = Drum motor rated belt pull
i = Speed ratio FWMIN = Minimum drum width
v = Speed SLMIN = Minimum shell length

© 12 | 2023 Interroll
52
 DRUM MOTOR
DM SERIES
DM 0080

Electrical data for 3-phase asynchronous motor

DL series
PN nP nN fN UN IN cosφ η JR IS/IN M S/ M B/ M P/ MN RM USHΔ USHY
[W] [min-1] [Hz] [V] [A] [kgcm2] MN MN MN [Nm] [Ω] [V] [V]

40 4 1278 50 230 0.38 0.72 0.37 0.59 1.93 1.31 1.51 1.31 0.3 294.5 40.3 −

40 4 1278 50 400 0.22 0.72 0.36 0.59 1.93 1.31 1.51 1.31 0.3 294.5 − 70

75 2 2659 50 230 0.46 0.82 0.5 0.59 3.04 1.48 1.70 1.48 0.27 164.4 31 −

75 2 2659 50 400 0.27 0.82 0.49 0.59 3.04 1.48 1.70 1.48 0.27 164.4 − 54.6

80 4 1308 50 230 0.64 0.68 0.46 1.11 2.20 1.46 1.65 1.46 0.58 132.5 28.8 −

80 4 1308 50 400 0.37 0.68 0.46 1.11 2.20 1.46 1.65 1.46 0.58 132.5 − 50

140 2 2796 50 230 0.65 0.79 0.68 1.11 3.86 1.88 2.03 1.88 0.49 72.7 18.7 −

140 2 2796 50 400 0.38 0.79 0.67 1.11 3.86 1.88 2.03 1.88 0.49 72.7 − 32.7

DM series
PN = Rated power IS/IN = Ratio of startup current – rated current
nP = Number of poles MS/MN = Ratio of startup torque – rated torque
nN = Rated speed of rotor MB/MN = Ratio of pull-out torque – rated torque
fN = Rated frequency MP/MN = Ratio of pull-up torque – rated torque
UN = Rated voltage MN = Rated torque of rotor
IN = Rated current RM = Branch resistance
cosφ = Power factor USHΔ = Heater voltage in delta connection

η = Efficiency USHY = Heater voltage in star connection

JR = Rotor moment of inertia

DP series
Application notes

© 12 | 2023 Interroll
53
DRUM MOTOR
DM SERIES
DM 0080

Mechanical data for 1-phase asynchronous motor with steel gear

PN nP gs i v nA MA FN FWMIN SLMIN
[W] [m/s] [1/min] [Nm] [N] [mm] [mm]

25 4 3 119.83 0.05 11.0 18.5 455 269 262

25 4 3 103.89 0.05 12.7 16.1 395 269 262

25 4 3 85.34 0.07 15.5 13.2 324 269 262

25 4 2 62.7 0.09 21.1 10.2 249 250 243

25 4 2 53.63 0.11 24.6 8.7 213 250 243

25 4 2 42.28 0.13 31.2 6.8 168 250 243

25 4 2 38.5 0.15 34.3 6.2 153 250 243

25 4 2 31.35 0.18 42.1 5.1 125 250 243

25 4 2 26.94 0.21 49.0 4.4 107 250 243

25 4 2 20.27 0.28 65.1 3.3 81 250 243

75 2 3 119.83 0.10 22.9 26.8 658 269 262

75 2 3 103.89 0.11 26.5 23.2 570 269 262

75 2 3 85.34 0.14 32.2 19.1 468 269 262

75 2 2 62.7 0.19 43.9 14.7 360 250 243

75 2 2 53.63 0.22 51.3 12.5 308 250 243

75 2 2 42.28 0.28 65.0 9.9 243 250 243

75 2 2 38.5 0.31 71.4 9.0 221 250 243

75 2 2 31.35 0.37 87.7 7.3 180 250 243

75 2 2 26.94 0.44 102.1 6.3 155 250 243

75 2 2 20.27 0.58 135.7 4.7 116 250 243

75 2 2 14.44 0.81 190.4 3.4 83 250 243

75 2 2 11.23 1.04 244.9 2.6 64 250 243

© 12 | 2023 Interroll
54
 DRUM MOTOR
DM SERIES
DM 0080

PN nP gs i v nA MA FN FWMIN SLMIN
[W] [m/s] [1/min] [Nm] [N] [mm] [mm]

DL series
85 2 3 119.83 0.10 22.9 30.9 759 269 262

85 2 3 103.89 0.11 26.5 26.8 658 269 262

85 2 3 85.34 0.14 32.2 22.0 540 269 262

85 2 2 62.7 0.19 43.9 16.9 415 250 243

85 2 2 53.63 0.22 51.3 14.5 355 250 243

85 2 2 42.28 0.28 65.0 11.4 280 250 243

85 2 2 38.5 0.31 71.4 10.4 255 250 243

85 2 2 31.35 0.37 87.7 8.5 208 250 243

85 2 2 26.94 0.44 102.1 7.3 178 250 243

DM series
85 2 2 20.27 0.58 135.7 5.5 134 250 243

85 2 2 14.44 0.81 190.4 3.9 96 250 243

85 2 2 11.23 1.04 244.9 3.0 74 250 243

110 2 3 119.83 0.10 23.0 39.2 961 269 262

110 2 3 103.89 0.11 26.5 34.0 833 269 262

110 2 3 85.34 0.14 32.2 27.9 684 269 262

110 2 2 62.7 0.19 43.9 21.4 526 250 243

110 2 2 53.63 0.22 51.3 18.3 450 250 243

110 2 2 42.28 0.28 65.0 14.5 355 250 243

110 2 2 38.5 0.31 71.4 13.2 323 250 243

DP series
110 2 2 31.35 0.37 87.7 10.7 263 250 243

110 2 2 26.94 0.44 102.1 9.2 226 250 243

110 2 2 20.27 0.58 135.7 6.9 170 250 243

110 2 2 14.44 0.81 190.5 4.9 121 250 243

110 2 2 11.23 1.05 244.9 3.8 94 250 243

PN = Rated power nA = Shell rated speed

nP = Number of poles MA = Drum motor rated torque
gs = Gear stages FN = Drum motor rated belt pull
Application notes

i = Speed ratio FWMIN = Minimum drum width

v = Speed SLMIN = Minimum shell length

© 12 | 2023 Interroll
55
DRUM MOTOR
DM SERIES
DM 0080

Mechanical data for 1-phase asynchronous motor with technopolymer gear

PN nP gs i v nA MA FN FWMIN SLMIN
[W] [m/s] [1/min] [Nm] [N] [mm] [mm]

25 4 3 115.2 0.05 11.5 17.8 436 287 280

25 4 3 96 0.06 13.8 14.8 364 287 280

25 4 3 78.55 0.07 16.8 12.1 297 287 280

25 4 3 71.56 0.08 18.4 11 271 287 280

75 2 3 96 0.12 28.6 21.4 525 287 280

75 2 3 78.55 0.15 35 17.5 430 287 280

75 2 3 71.56 0.16 38.4 16 391 287 280

75 2 3 63.51 0.19 43.3 14.2 347 287 280

85 2 3 78.55 0.15 35 20.2 496 287 280

85 2 3 71.56 0.16 38.4 18.4 452 287 280

85 2 3 63.51 0.19 43.3 16.3 401 287 280

110 2 3 63.51 0.19 43.3 20.7 508 287 280

110 2 3 52.92 0.22 52 17.2 423 287 280

110 2 3 48.79 0.24 56.4 15.9 390 287 280

110 2 3 43.3 0.27 63.5 14.1 346 287 280

110 2 2 19.2 0.61 143.2 6.6 162 287 280

110 2 2 16 0.73 171.9 5.5 135 287 280

110 2 2 13.09 0.90 210.1 4.5 110 287 280

PN = Rated power nA = Shell rated speed

nP = Number of poles MA = Drum motor rated torque
gs = Gear stages FN = Drum motor rated belt pull
i = Speed ratio FWMIN = Minimum drum width
v = Speed SLMIN = Minimum shell length

© 12 | 2023 Interroll
56
 DRUM MOTOR
DM SERIES
DM 0080

Electrical data for 1-phase asynchronous motor

DL series
PN nP nN fN UN IN cosφ η JR IS/IN M S/ M B/ M P/ MN RP USH ~ CR
[W] [min-1] [Hz] [V] [A] [kgcm2] MN MN MN [Nm] [Ω] [V DC] [µF]

25 4 1320 50 230 0.39 1 0.28 1.11 2.19 1.11 1.37 1.11 0.18 150 44 3

50 2 2750 50 230 0.54 1 0.4 0.74 3.08 0.94 1.71 0.94 0.17 82 33 3

75 2 2750 50 230 0.68 1 0.48 0.89 3.19 0.74 1.37 0.74 0.26 66 34 4

85 2 2750 50 230 0.73 0.98 0.52 1.11 2.50 0.88 1.77 0.88 0.3 52 28 6

110 2 2750 50 230 0.94 1 0.51 1.11 1.97 0.73 1.15 0.73 0.38 52 37 8

PN = Rated power IS/IN = Ratio of startup current – rated current

nP = Number of poles MS/MN = Ratio of startup torque – rated torque

DM series
nN = Rated speed of rotor MB/MN = Ratio of pull-out torque – rated torque
fN = Rated frequency MP/MN = Ratio of pull-up torque – rated torque
UN = Rated voltage MN = Rated torque of rotor
IN = Rated current RP = Phase to phase resistance
cosφ = Power factor USH ~ = Heater voltage for DC units

η = Efficiency CR = Capacitor size

JR = Rotor moment of inertia

DP series
Application notes

© 12 | 2023 Interroll
57
DRUM MOTOR
DM SERIES
DM 0080

Belt tension diagrams

Belt tension depending on drum width

7500

6500

5500
TE [N]

4500

3500

2500

1500

500
500 600 700 800 900 1000 1100 1200
FW [mm]

Belt tension depending on rated speed of shell

8000

7500

7000

6500

6000

5500
TE [N]

5000

4500

4000

3500

3000

2500

2000
0 50 100 150 200 250 300 350 400 450 500 550 600
nA [1/min]

Note: The correct value for the maximum permissible belt tension is determined from the speed of the drum motor. When selecting the
motor, also check whether the maximum permissible TE value fits the desired drum width (FW). The belt tension diagrams apply only to
standard shafts.

TE = Belt tension
nA = Shell rated speed
FW = Drum width

© 12 | 2023 Interroll
58
 DRUM MOTOR
DM SERIES
DM 0080

Dimensions
Drum motor

DL series
AGL
C EL C
E E

A-A
F
A

D ØB ØA

DM series
P SL=FW-2xP P
FW

Type A B C D S F P SL EL AGL
[mm] [mm] [mm] [mm] [mm] [mm] [mm] [mm] [mm] [mm]
DM 0080 Standard 81.5 80.5 12.5 30 2.5 25 3.5 FW − 7 FW + 5 FW + 30
crowned
Optional 81.5 80.5 12.5 25 2.5 20 3.5 FW − 7 FW + 5 FW + 30

Optional 81.5 80.5 12.5 17 2.5 13.5 3.5 FW − 7 FW + 5 FW + 30

DM 0080 Standard 81 81 12.5 30 2.5 25 3.5 FW − 7 FW + 5 FW + 30

cylindrical
Optional 81 81 12.5 25 2.5 20 3.5 FW − 7 FW + 5 FW + 30

DP series
Optional 81 81 12.5 17 2.5 13.5 3.5 FW − 7 FW + 5 FW + 30

DM 0080 Standard 81.7 81.7 12.5 30 2.5 25 3.5 FW − 7 FW + 5 FW + 30

cylindrical +
Optional 81.7 81.7 12.5 25 2.5 20 3.5 FW − 7 FW + 5 FW + 30
key
Optional 81.7 81.7 12.5 17 2.5 13.5 3.5 FW − 7 FW + 5 FW + 30
Application notes

© 12 | 2023 Interroll
59