Continental Device India Pvt.
Limited
An IATF 16949, ISO9001 and ISO 14001 Certified Company
SILICON PLANAR POWER TRANSISTORS CL100 A/B NPN
CK100 A/B PNP
TO-39
Metal Can Package
RoHS compliant
FEATURE:
1. This product is available in AEC-Q101 Compliant and PPAP Capable also.
Note: For AEC-Q101 compliant products, please use suffix -AQ in the part number while ordering.
APPLICATIONS:
Medium Power Transistors Suitable for a wide Range of Medium Voltage and Current Amplifier.
ABSOLUTE MAXIMUM RATINGS (Ta = 25 ℃ Unless otherwise specified)
PARAMETER SYMBOL VALUE UNIT
Collector Emitter Voltage VCER 50 V
Collector Base Voltage VCBO 60 V
Emitter Base Voltage VEBO 5.0 V
Collector Current - Continuous IC 1.0 A
Power Dissipation@ Ta=25ºC 0.8 W
PD
Derate Above 25ºC 4.57 mW/°C
Power Dissipation@ Tc=25ºC 4.0 W
PD
Derate Above 25ºC 22.73 mW/°C
Operating and Storage Junction
Tj, Tstg -65 to +200 °C
Temperature Range
Junction to Ambient in free air Rth(j-a) 219
°C/W
Junction to Case Rth(j-c) 44
ELECTRICAL CHARACTERISTICS at (Ta = 25 ℃ Unless otherwise specified)
PARAMETER SYMBOL TEST CONDITIONS MIN TYP MAX UNIT
Collector Emitter Voltage VCEO 1 IC=10mA, IB=0 50 -- -- V
Collector Base Voltage VCBO IC=100µA, IE=0 60 -- -- V
Emitter Base Voltage VEBO IE=100µA, IC=0 5 -- -- V
Collector Cut off Current ICBO VCB=40V, IE=0 -- -- 50 nA
Emitter Cut off Current IEBO VEB=4V, IE=0 -- -- 1.0 µA
DC Current Gain hFE 1 IC=150mA, VCE=10V 40 -- 300
Collector Emitter Saturation Voltage VCE (sat) 1 IC=150mA, IB=15mA -- -- 0.6 V
Base Emitter on Voltage VBE (on) 1 IC=150mA, VCE=1V -- -- 0.9 V
Note:
1. Pulsed: Pulse width ≤300µs, duty cycle ≤2%
2. For PNP device voltage and current values will be negative (-).
hFE Classification : A : 40 -120 B: 100 - 300
CL100 A/B_CK100 A/B
Rev01 18072022EM
Continental Device India Pvt. Limited Data Sheet Page 1 of 8
Continental Device India Pvt. Limited
An IATF 16949, ISO9001 and ISO 14001 Certified Company
Recommended Reflow Solder Profiles
The recommended reflow solder profiles for Pb and Pb-free devices are shown below.
Figure 1 shows the recommended solder profile for devices that have Pb-free terminal plating, and where a
Pb-free solder is used.
Figure 2 shows the recommended solder profile for devices with Pb-free terminal plating used with leaded
solder, or for devices with leaded terminal plating used with a leaded solder.
Figure 1 Figure 2
Profile Feature Sn-Pb System Pb-Free System
Average Ramp-Up Rate ~3°C/second ~3°C/second
Preheat
– Temperature Range 150-170°C 150-200°C
– Time 60-180 seconds 60-180 seconds
Time maintained above:
– Temperature 200°C 217°C
– Time 30-50 seconds 60-150 seconds
Peak Temperature 235°C 260°C max.
Time within +0 -5°C of actual Peak 10 seconds 40 seconds
Ramp-Down Rate 3°C/second max. 6°C/second max.
CL100 A/B_CK100 A/B
Rev01 18072022EM
Continental Device India Pvt. Limited Data Sheet Page 2 of 8
Continental Device India Pvt. Limited
An IATF 16949, ISO9001 and ISO 14001 Certified Company
Recommended Wave Solder Profiles
The Recommended solder Profile For Devices
The Recommended solder Profile For Devices
with Pb-free terminal plating used with leaded
with Pb-free terminal plating where a
solder, or for devices with leaded terminal
Pb-free solder is used
plating used with leaded solder
Wave Profiles in Tabular Form
Profile Feature Sn-Pb System Pb-Free System
Average Ramp-Up Rate ~200°C/second ~200°C/second
Heating rate during preheat Typical 1-2, Max 4°C/sec Typical 1-2, Max 4°C/Sec
Final preheat Temperature Within 125°C of Solder Temp Within 125°C of Solder Temp
Peak Temperature 235°C 260°C max.
Time within +0 -5°C of actual Peak 10 seconds 10 seconds
Ramp-Down Rate 5°C/second max. 5°C/second max
CL100 A/B_CK100 A/B
Rev01 18072022EM
Continental Device India Pvt. Limited Data Sheet Page 3 of 8
Continental Device India Pvt. Limited
An IATF 16949, ISO9001 and ISO 14001 Certified Company
TYPICAL CHARACTERISTICS CURVES
Fig 1: Total Permissible Power Dissipation Versus Fig 4: Permissible Pulse Load
Temperature Ptot = f (T); VCE = Parameter rthJC = f(t); v = Parameter
Fig 2: Permissible Operating Range IC = f Fig 4: Permissible Operating Range
(VCE);(Tcase = 60°C) IC = f (VCE);(Tcase = 125°C)
Fig 3: DC Current Gain hFE = f (IC) VCE = 5V; Fig 7: Collector Cutoff Current
Tamb = Parameter Versus Temperature ICBO = f (Tamb) nA-VCE = 60V
CL100 A/B_CK100 A/B
Rev01 18072022EM
Continental Device India Pvt. Limited Data Sheet Page 4 of 8
Continental Device India Pvt. Limited
An IATF 16949, ISO9001 and ISO 14001 Certified Company
TYPICAL CHARACTERISTICS CURVES
Fig 6: Collector-Emitter Saturation Voltage Fig 8: Base-Emitter Saturation Voltage
Fig 9: Collector Current IC = f(VBE) Fig 10: Transition frequency fT = f (IC)
CL100 A/B_CK100 A/B
Rev01 18072022EM
Continental Device India Pvt. Limited Data Sheet Page 5 of 8
Continental Device India Pvt. Limited
An IATF 16949, ISO9001 and ISO 14001 Certified Company
PACKAGE DETAILS
TO-39 Metal Can Package
DIM MIN MAX
A 8.50 9.39
B 7.74 8.50
C 6.09 6.60
D 0.40 0.53
E -- 0.88
F 2.41 2.66
G 4.82 5.33
H 0.71 0.86
J 0.73 1.02
K 12.700 --
L 42° 48°
All dimensions are in mm
PIN CONFIGURATION
1. Emitter
2. Base
3. Collector
Packing Detail
CL100 A/B_CK100 A/B
Rev01 18072022EM
Continental Device India Pvt. Limited Data Sheet Page 6 of 8
Continental Device India Pvt. Limited
An IATF 16949, ISO9001 and ISO 14001 Certified Company
Recommended Product Storage Environment for Discrete
Semiconductor Devices
This storage environment assumes that the Diodes and transistors are packed properly inside
the original packing supplied by CDIL.
ꞏ Temperature 5 °C to 30 °C
ꞏ Humidity between 40 to 70 %RH
ꞏ Air should be clean.
ꞏ Avoid harmful gas or dust.
ꞏ Avoid outdoor exposure or storage in areas subject to rain or water spraying .
ꞏ Avoid storage in areas subject to corrosive gas or dust. Product shall not be stored in areas
exposed to direct sunlight.
ꞏ Avoid rapid change of temperature.
ꞏ Avoid condensation.
ꞏ Mechanical stress such as vibration and impact shall be avoided.
ꞏ The product shall not be placed directly on the floor.
ꞏ The product shall be stored on a plane area. They should not be turned upside down.
They should not be placed against the wall.
Shelf Life of CDIL Products
The shelf life of products is the period from product manufacture to shipment to customers. The product can be
unconditionally shipped within this period. The period is defined as 2 years.
If products are stored longer than the shelf life of 2 years the products shall be subjected to quality check as
per CDIL quality procedure.
The products are further warranted for another one year after the date of shipment subject to the above
conditions in CDIL original packing.
Floor Life of CDIL Products and MSL Level
When the products are opened from the original packing, the floor life will start.
For this, the following JEDEC table may be referred:
JEDEC MSL Level
Level Time Condition
1 Unlimited ≤30 °C / 85% RH
2 1 Year ≤30 °C / 60% RH
2a 4 Weeks ≤30 °C / 60% RH
3 168 Hours ≤30 °C / 60% RH
4 72 Hours ≤30 °C / 60% RH
5 48 Hours ≤30 °C / 60% RH
5a 24 Hours ≤30 °C / 60% RH
6 Time on Label(TOL) ≤30 °C / 60% RH
CL100 A/B_CK100 A/B
Rev01 18072022EM
Continental Device India Pvt. Limited Data Sheet Page 7 of 8
Continental Device India Pvt. Limited
An IATF 16949, ISO9001 and ISO 14001 Certified Company
Customer Notes
Component Disposal Instructions
1. CDIL Semiconductor Devices are RoHS compliant, customers are requested to please
dispose as per prevailing Environmental Legislation of their Country.
2. In Europe, please dispose as per EU Directive 2002/96/EC on Waste Electrical and
Electronic Equipment (WEEE).
Disclaimer
The product information and the selection guides facilitate selection of the CDIL's Semiconductor Device(s)
best suited for application in your product(s) as per your requirement. It is recommended that you completely
review our Data Sheet(s) so as to confirm that the Device(s) meet functionality parameters for your application.
The information furnished in the Data Sheet and on the CDIL Web Site/CD are believed to be accurate and
reliable. CDIL however, does not assume responsibility for inaccuracies or incomplete information.
Furthermore, CDIL does not assume liability whatsoever, arising out of the application or use of any CDIL
product; neither does it convey any license under its patent rights nor rights of others. These products are not
designed for use in life saving/support appliances or systems. CDIL customers selling these products (either
as individual Semiconductor Devices or incorporated in their end products), in any life saving/support
appliances or systems or applications do so at their own risk and CDIL will not be responsible for any
damages resulting from such sale(s).
CDIL strives for continuous improvement and reserves the right to change the specifications of its products
without prior notice.
CDIL is a registered trademark of
Continental Device India Pvt. Limited
C-120 Naraina Industrial Area, New Delhi 110 028, India.
Telephone +91-11-2579 6150, 4141 1112 Fax +91-11-2579 5290, 4141 1119
[email protected] www.cdil.com
CIN No. U32109DL1964PTC004291
CL100 A/B_CK100 A/B
Rev01 18072022EM
Continental Device India Pvt. Limited Data Sheet Page 8 of 8
