PRESTRESSED CONCRETE
HIGH-STRENGTH
APPLICATION IMPORTANT NOTES
Designed to support: • The loading figures published in the load-
• Masonry loads span tables represent the Uniform Distributed
• Uniformly distributed timber floor loads Serviceable Load (UDL) in kN/m which can be
• Uniformly distributed roof loads supported by the lintel without the provision
• Concrete floor loads of structural brickwork/blockwork over. This is
• Attic truss loads known as Independent Design.
• Point loads: compound trusses, steel beams, • Lintel lengths shown greyed out within the
etc load-span table are available in longer
lengths than the maximum clear span would
ALWAYS CHECK LOADINGS AGAINST OUR normally allow. These longer lengths lintels
LOAD-SPAN TABLE should be used over a series of openings
(with intermediate supports) NOT exceeding
INSTALLATION NOTES the maximum clear span and NOT simply
For general installation notes please refer supported at each end (i.e. all 70mm
to page 67. deep lintels must not clear span more than
1800mm).
Additional installation requirements for lintels • Lintels are marked TOP and must be used in
supporting concrete floor units the correct orientation
• Check that the correct lintel has been
installed. ABBREVIATIONS:
• Minimum recommended lintel depth is UDL – Uniform Distributed Load (Serviceable)
140mm in order to absorb the shock loading RM – Resistance Moment (Serviceable)
of concrete floor. Precast flooring units should
be laid on a mortar bed across the whole
wall width and should not be dragged over
supports.
ADVANTAGES
% 01455 272457
If in doubt please contact our
technical department on
• A cost effective, high performance range of
lintels
• Easy to install and suitable for a variety of
applications: internal partitions, external
cavity walls, garages, over services.
HIGH-STRENGTH
• We offer a wide range of lintels from
100 x 70 through to 215 x 215.
• If required, Stressline can schedule and
deliver in house plots.
© Stressline Limited 2016
52
STANDARD 900 1200 1350 1500 1650 1800 2100 2400 2700 3000 3300 3600 4050 4200 100 x 140
LENGTHS (mm) HIGH-STRENGTH
Clear Span (mm) 600 900 1050 1200 1350 1500 1800 2100 2400 2700 3000 3300 3600 3900 100
Weight (Kg/m) 33.0 33.0 33.0 33.0 33.0 33.0 33.0 33.0 33.0 33.0 33.0 33.0 33.0 33.0
140
UDL (kN/m) 68.7* 40.6 35.0 27.0 21.9 17.7 12.5 9.2 7.1 5.6 4.5 3.7 3.1 2.6
RM (kNm) 5.8 5.8 5.8 5.8 5.8 5.8 5.8 5.8 5.8 5.8 5.8 5.8 5.8 5.8
*UDL is restricted by shear
Minimum manufactured length is 900mm Maximum manufactured length is 4200mm
STANDARD 900 1200 1350 1500 1650 1800 2100 2400 2700 3000 3300 3600 4050 4200 100 x 215
LENGTHS (mm) HIGH-STRENGTH
Clear Span (mm) 600 900 1050 1200 1350 1500 1800 2100 2400 2700 3000 3300 3600 3900 100
Weight (Kg/m) 53.9 53.9 53.9 53.9 53.9 53.9 53.9 53.9 53.9 53.9 53.9 53.9 53.9 53.9
215
UDL (kN/m) 78.5* 63.2 57.4 49.2 43.1 36.9 27.2 21.5 16.7 13.3 10.8 9.0 7.5 6.4
RM (kNm) 14.4 14.4 14.4 14.4 14.4 14.4 14.4 14.4 14.4 14.4 14.4 14.4 14.4 14.4
*UDL is restricted by shear
Minimum manufactured length is 900mm Maximum manufactured length is 4200mm
140 x 140 STANDARD 900 1200 1350 1500 1800 2100 2400 2700 3000 3300 3600 4050 4200
HIGH-STRENGTH LENGTHS (mm)
140
Clear Span (mm) 600 900 1050 1200 1500 1800 2100 2400 2700 3000 3300 3600 3900
Weight (Kg/m) 48.0 48.0 48.0 48.0 48.0 48.0 48.0 48.0 48.0 48.0 48.0 48.0 48.0
140
UDL (kN/m) 67.5* 57.9 52.1 39.2 26.5 18.6 13.8 10.6 8.4 6.7 5.6 4.6 3.8
RM (kNm) 8.8 8.8 8.8 8.8 8.8 8.8 8.8 8.8 8.8 8.8 8.8 8.8 8.8
*UDL is restricted by shear
Minimum manufactured length is 900mm Maximum manufactured length is 4200mm
140 x 215 STANDARD 900 1200 1350 1500 1800 2100 2400 2700 3000 3300 3600 4050 4200
HIGH-STRENGTH LENGTHS (mm)
140
Clear Span (mm) 600 900 1050 1200 1500 1800 2100 2400 2700 3000 3300 3600 3900
Weight (Kg/m) 75.4 75.4 75.4 75.4 75.4 75.4 75.4 75.4 75.4 75.4 75.4 75.4 75.4
UDL (kN/m) 101.2* 81.2 73.5 63.2 46.3 33.2 24.9 19.4 15.4 12.5 10.3 8.6 7.3
RM (kNm) 16.8 16.8 16.8 16.8 16.8 16.8 16.8 16.8 16.8 16.8 16.8 16.8 16.8
*UDL is restricted by shear
Minimum manufactured length is 900mm Maximum manufactured length is 4200mm
215 x 215 STANDARD 900 1200 1500 1800 2100 2400 2700 3000 3300 3600 4050 4200
HIGH-STRENGTH LENGTHS (mm)
215
Clear Span (mm) 600 900 1200 1500 1800 2100 2400 2700 3000 3300 3600 3900
Weight (Kg/m) 113.2 113.2 113.2 113.2 113.2 113.2 113.2 113.2 113.2 113.2 113.2 113.2
UDL (kN/m) 143.0* 112.4* 77.8 51.6 36.5 27.1 20.9 16.5 13.3 10.9 9.0 7.6
RM (kNm) 17.7 17.7 17.7 17.7 17.7 17.7 17.7 17.7 17.7 17.7 17.7 17.7
*UDL is restricted by shear
Minimum manufactured length is 900mm Maximum manufactured length is 4200mm
© Stressline Limited 2016
53
