OmniClass Software Suite

Architect and Engineering

Specifications
Date: July 6, 2005
1 Sample Specifications for Architects and
Specifying Engineers
The following document contains sample specifications for OmniClass 13.56 MHz contactless smart card
products. They are written using industry standard formatting and language. These specifications are for
use by architects, consultants, and specifying engineers who are preparing bid specifications for access
control, building control and security systems.
The electronic version of these specifications may be copied into the appropriate sections of a complete
bid specification by using the “cut and paste” method. They are written to highlight unique and powerful
features of OmniClass contactless smart cards and readers.
Section headings mention specific models only for clarity – these may be deleted after insertion into the
complete specification. Models covered include the OmniClass OM30, OM40, OM45, and OM55, as well
as OmniClass Cards, Key Fobs and Stickers (Tags).
If you require technical specifications or additional information on these products, please visit the
HONEYWELL website at [Link].
OmniClass™ is a trademark of HONEYWELL Corporation. All other trademarks and registered
trademarks are the property of their respective owners.

1.1 ALARM AND ACCESS CONTROL EQUIPMENT

1.1.1 MANUFACTURERS
 Access control credential readers shall be as manufactured by Honeywell Access Systems, 135
W. Forest Hill Avenue, Oak Creek, WI 53154 (800-323-4576).
 Substitutions: No substitutions allowed.

1.1.2 Contactless Smart Access Control Readers

Provide OmniClass Contactless Smart Card readers as shown on the drawings. Card readers shall be
"single-package" type, combining controller, electronics and antenna in one package in the following
configurations:

[Link] OM30 Mullion

Contactless Smart Card Reader, Special Mounting (applications with a minimum of mounting space):
 Provide surface mounting style 13.56 MHz contactless smart card readers suitable for minimal
space mounting configurations as shown on the project plans.
 Contactless smart card readers shall comply with ISO 15693, ISO 14443A (CSN), and ISO
14443B and shall read credentials that comply with these standards.

Document 7-501121, Revision 00 Architect and Engineering Specification

© 2005 Honeywell International. Confidential. 1 OmniClass Readers and Credentials

  Contactless smart card readers shall output credential data in compliance with the SIA AC-01
Wiegand standard as follows:
o Reads standard proximity format data from OmniClass cards and outputs data as
encoded.
o Reads card serial number (CSN) of a MIFARE card with configurable outputs as 26-bit,
32-bit, 34-bit, 40-bit, or 56-bit.
 Data security with OmniClass cards shall use 64-bit authentication keys to reduce the risk of
compromised data or duplicate cards. The contactless smart card reader and OmniClass cards
shall require matching keys in order to function together. All RF data transmission between the
card and the reader shall be encrypted, using a secure algorithm. Card readers shall be provided
with keys that are compatible with the OmniClass cards.
 The reader shall be of potted, polycarbonate material, sealed to a NEMA rating of 4X (IP65).
 The contactless smart card reader shall provide the ability to change operational features in the
field through the use of a factory-programmed command card. Additionally, firmware may be
updated by flashing the reader. Command card operational programming options shall include:
o Output configurations
o LED & Audio configurations
o Keypad configurations
 Contactless smart card readers shall provide the following programmable audio/visual indication:
o An audio transducer shall provide various tone sequences to signify: access granted,
access denied, power up, and diagnostics.
o A high-intensity light bar shall provide clear visual status (red/green/amber) that is
visible even in bright sunlight.
 Typical contactless smart card read range shall be:
o 2” – 3” (5.0 – 7.6 cm) using OmniClass card
o 1” (2.5 cm) using OmniClass Key Fob
o 1” (2.5 cm) using OmniClass Sticker (Tag)
o 1” – 1.5” (2.5 – 3.8 cm) using OmniClass + HID 125KHz Prox card
o 1” – 2” (2.5 – 5.0 cm) using MIFARE Card (card serial number only)
 Contactless smart card readers shall meet the following physical specifications:
o Dimensions: 1.90” x 4.04” x .80” (4.83cm x 10.26 cm x 2.03 cm)
o Weight: [Link] (90.7 g)
o Material: UL94 Polycarbonate
o Three-part design with separate mounting plate, reader body, and cover.
o Color: Black.
 Contactless smart card readers shall meet the following electrical specifications:
o Operating voltage: 10 – 16 VDC, reverse voltage protected. Linear power supply
recommended.
o Current requirements: (average/peak) 61/178mA @ 12 VDC

Document 7-501121, Revision 00 Architect and Engineering Specification

© 2005 Honeywell International. Confidential. 2 OmniClass Readers and Credentials

  Contactless smart card readers shall meet the following certifications:
o UL 294
o Canada/UL 294
o FCC Certification
o Canada Radio Certification
o EU and CB Scheme Electrical Safety
o EU – R&TTE Directive
o CE Mark (Europe)
o IP55 Rated
o C-Tick (New Zealand/Australia/Taiwan)
 Contactless smart card readers shall meet the following environmental specifications:
o Operating temperature: -30 to 150 degrees F (-35 to 65 degrees C)
o Operating humidity: 5% to 95% relative humidity non-condensing
o Weatherized design suitable to withstand harsh environments
 Contactless smart card reader cabling requirements shall be:
o Cable distance: (Wiegand): 500 feet (150m)
o Cable type: 5-conductor #22 AWG with overall shield
o Standard reader termination: 18” (.5m) cable pigtail
 Warranty of contactless smart card readers shall be lifetime against defects in materials and
workmanship.
 Contactless smart card reader shall be Honeywell OM30 compatible with selected card media.

[Link] OM40 US Single-Gang

Contactless Smart Card Reader, Wall Mounting (US Single-Gang Mounting Applications):
 Provide surface mounting style 13.56 MHz contactless smart card readers suitable for minimal
space mounting configurations as shown on the project plans.
 Contactless smart card readers shall comply with ISO 15693, ISO 14443A (CSN), and ISO
14443B and shall read credentials that comply with these standards.
 Contactless smart card readers shall output credential data in compliance with the SIA AC-01
Wiegand standard as follows:
o Reads standard proximity format data from OmniClass cards and outputs data as
encoded.
o Reads card serial number (CSN) of a MIFARE card with configurable outputs as 26-bit,
32-bit, 34-bit, 40-bit, or 56-bit.
 Data security with OmniClass cards shall use 64-bit authentication keys to reduce the risk of
compromised data or duplicate cards. The contactless smart card reader and OmniClass cards
shall require matching keys in order to function together. All RF data transmission between the
card and the reader shall be encrypted, using a secure algorithm. Card readers shall be provided
with keys that are compatible with the OmniClass cards.

Document 7-501121, Revision 00 Architect and Engineering Specification

© 2005 Honeywell International. Confidential. 3 OmniClass Readers and Credentials

  The reader shall be of potted, polycarbonate material, sealed to a NEMA rating of 4X (IP65).
 The contactless smart card reader shall provide the ability to change operational features in the
field through the use of a factory-programmed command card. Additionally, firmware may be
updated by flashing the reader. Command card operational programming options shall include:
o Output configurations
o LED & Audio configurations
o Keypad configurations
 Contactless smart card readers shall provide the following programmable audio/visual indication:
o An audio transducer shall provide various tone sequences to signify: access granted,
access denied, power up, and diagnostics.
o A high-intensity light bar shall provide clear visual status (red/green/amber) that is
visible even in bright sunlight.
 Typical contactless smart card read range shall be:
o 2.5” – 4.5” (6.3 – 11.4 cm) using OmniClass card
o 1” (2.5 cm) using OmniClass Key Fob
o 1” (2.5 cm) using OmniClass Sticker (Tag)
o 1.5” – 2” (3.8 – 5.0 cm) using OmniClass + 125KHz HID Prox card
o 1” – 2” (2.5 – 5.0 cm) using MIFARE Card (card serial number only)
 Contactless smart card readers shall meet the following physical specifications:
o Dimensions: 3.30” x 4.80” x .85” (8.38cm x 12.19 cm x 2.16 cm)
o Weight: [Link] (249.5 g)
o Material: UL94 Polycarbonate
o Three-part design with separate mounting plate, reader body, and cover.
o Color: Black.
 Contactless smart card readers shall meet the following electrical specifications:
o Operating voltage: 10 – 16 VDC, reverse voltage protected. Linear power supply
recommended.
o Current requirements: (average/peak) 78/234mA @ 12 VDC
 Contactless smart card readers shall meet the following certifications:
o UL 294
o Canada/UL 294
o FCC Certification
o Canada Radio Certification
o EU and CB Scheme Electrical Safety
o EU – R&TTE Directive
o CE Mark (Europe)
o IP55 Rated

Document 7-501121, Revision 00 Architect and Engineering Specification

© 2005 Honeywell International. Confidential. 4 OmniClass Readers and Credentials

 o C-Tick (New Zealand/Australia/Taiwan)
 Contactless smart card readers shall meet the following environmental specifications:
o Operating temperature: -30 to 150 degrees F (-35 to 65 degrees C)
o Operating humidity: 5% to 95% relative humidity non-condensing
o Weatherized design suitable to withstand harsh environments
 Contactless smart card reader cabling requirements shall be:
o Cable distance: (Wiegand): 500 feet (150m)
o Cable type: 5-conductor #22 AWG with overall shield
o Standard reader termination: 18” (.5m) cable pigtail
 Warranty of contactless smart card readers shall be lifetime against defects in materials and
workmanship.
 Contactless smart card reader shall be Honeywell OM40 compatible with selected card media.

[Link] OM45 European/Asian Single-Gang

Contactless Smart Card Reader, Wall Mounting, (European or Asian Single-Gang Mounting
Applications):
 Provide surface mounting style 13.56 MHz contactless smart card readers suitable for minimal
space mounting configurations as shown on the project plans.
 Contactless smart card readers shall comply with ISO 15693, ISO 14443A (CSN), and ISO
14443B and shall read credentials that comply with these standards.
 Contactless smart card readers shall output credential data in compliance with the SIA AC-01
Wiegand standard as follows:
o Reads standard proximity format data from OmniClass cards and outputs data as
encoded.
o Reads card serial number (CSN) of a MIFARE card with configurable outputs as 26-bit,
32-bit, 34-bit, 40-bit, or 56-bit.
 Data security with OmniClass cards shall use 64-bit authentication keys to reduce the risk of
compromised data or duplicate cards. The contactless smart card reader and OmniClass cards
shall require matching keys in order to function together. All RF data transmission between the
card and the reader shall be encrypted, using a secure algorithm. Card readers shall be provided
with keys that are compatible with the OmniClass cards.
 The reader shall be of potted, polycarbonate material, sealed to a NEMA rating of 4X (IP65).
 The contactless smart card reader shall provide the ability to change operational features in the
field through the use of a factory-programmed command card. Additionally, firmware may be
updated by flashing the reader. Command card operational programming options shall include:
o Output configurations
o LED & Audio configurations
o Keypad configurations
 Contactless smart card readers shall provide the following programmable audio/visual indication:

Document 7-501121, Revision 00 Architect and Engineering Specification

© 2005 Honeywell International. Confidential. 5 OmniClass Readers and Credentials

 o An audio transducer shall provide various tone sequences to signify: access granted,
access denied, power up, and diagnostics.
o A high-intensity light bar shall provide clear visual status (red/green/amber) that is
visible even in bright sunlight.
 Typical contactless smart card read range shall be:
o 2” – 3” (5.0 – 7.6 cm) using OmniClass card
o 1” (2.5 cm) using OmniClass Key Fob
o 1” (2.5 cm) using OmniClass Sticker (Tag)
o 1.5” – 2” (3.8 – 5.0 cm) using OmniClass + 125KHz HID Prox card
o 1” – 2” (2.5 – 5.0 cm) using MIFARE Card (card serial number only)
 Contactless smart card readers shall meet the following physical specifications:
o Dimensions: 3.90” x 3.90” x .75” (8.38 cm x 8.38 cm x 1.91 cm)
o Weight: 4.0 oz (113.4 g)
o Material: UL94 Polycarbonate
o Three-part design with separate mounting plate, reader body, and cover.
o Color: Black.
 Contactless smart card readers shall meet the following electrical specifications:
o Operating voltage: 10 – 16 VDC, reverse voltage protected. Linear power supply
recommended.
o Current requirements: (average/peak) 80/260mA @ 12 VDC
 Contactless smart card readers shall meet the following certifications:
o UL 294
o Canada/UL 294
o FCC Certification
o Canada Radio Certification
o EU and CB Scheme Electrical Safety
o EU – R&TTE Directive
o CE Mark (Europe)
o IP55 Rated
o C-Tick (New Zealand/Australia/Taiwan)
 Contactless smart card readers shall meet the following environmental specifications:
o Operating temperature: -30 to 150 degrees F (-35 to 65 degrees C)
o Operating humidity: 5% to 95% relative humidity non-condensing
o Weatherized design suitable to withstand harsh environments
 Contactless smart card reader cabling requirements shall be:
o Cable distance: (Wiegand): 500 feet (150m)
o Cable type: 5-conductor #22 AWG with overall shield

Document 7-501121, Revision 00 Architect and Engineering Specification

© 2005 Honeywell International. Confidential. 6 OmniClass Readers and Credentials

 o Standard reader termination: 18” (.5m) cable pigtail
 Warranty of contactless smart card readers shall be lifetime against defects in materials and
workmanship.
 Contactless smart card reader shall be Honeywell OM45 compatible with selected card media.

[Link] OM55
Contactless Smart Card Reader , Wall Mounting (Keypad Applications):
 Provide surface mounting style 13.56 MHz contactless smart card readers suitable for minimal
space mounting configurations as shown on the project plans.
 Contactless smart card readers shall comply with ISO 15693, ISO 14443A (CSN), and ISO
14443B and shall read credentials that comply with these standards.
 Contactless smart card readers shall output credential data in compliance with the SIA AC-01
Wiegand standard as follows:
o Reads standard proximity format data from OmniClass cards and outputs data as
encoded.
o Reads card serial number (CSN) of a MIFARE card with configurable outputs as 26-bit,
32-bit, 34-bit, 40-bit, or 56-bit.
 Data security with OmniClass cards shall use 64-bit authentication keys to reduce the risk of
compromised data or duplicate cards. The contactless smart card reader and OmniClass cards
shall require matching keys in order to function together. All RF data transmission between the
card and the reader shall be encrypted, using a secure algorithm. Card readers shall be provided
with keys that are compatible with the OmniClass cards.
 The reader shall be of potted, polycarbonate material, sealed to a NEMA rating of 4X (IP65).
 The contactless smart card reader shall provide the ability to change operational features in the
field through the use of a factory-programmed command card. Additionally, firmware may be
updated by flashing the reader. Command card operational programming options shall include:
o Output configurations
o LED & Audio configurations
o Keypad configurations
 Contactless smart card readers shall provide the following programmable audio/visual indication:
o An audio transducer shall provide various tone sequences to signify: access granted,
access denied, power up, and diagnostics.
o A high-intensity light bar shall provide clear visual status (red/green/amber) that is
visible even in bright sunlight.
 Typical contactless smart card read range shall be:
o 3” – 4” (7.6 – 10.1 cm) using OmniClass card
o 1” – 1.5” (2.5 – 3.8 cm) using OmniClass Key Fob
o 1” – 1.5” (2.5 – 3.8 cm) using OmniClass Sticker (Tag)
o 1.5” – 2.0” (3.8 – 5.0 cm) using OmniClass + 125KHz HID Prox card
o 1” – 2” (2.5 – 5.0 cm) using MIFARE Card (card serial number only)

Document 7-501121, Revision 00 Architect and Engineering Specification

© 2005 Honeywell International. Confidential. 7 OmniClass Readers and Credentials

  Contactless smart card readers shall meet the following physical specifications:
o Dimensions: 3.30” x 4.80” x .90” (8.38cm x 12.19 cm x 2.28 cm)
o Weight: 10oz (283.4 g)
o Material: UL94 Polycarbonate
o Three-part design with separate mounting plate, reader body, and cover.
o Color: Black.
 Contactless smart card readers shall meet the following electrical specifications:
o Operating voltage: 10 – 16 VDC, reverse voltage protected. Linear power supply
recommended.
o Current requirements: (average/peak) 61/178mA @ 12 VDC
 Contactless smart card readers shall meet the following certifications:
o UL 294
o Canada/UL 294
o FCC Certification
o Canada Radio Certification
o EU and CB Scheme Electrical Safety
o EU – R&TTE Directive
o CE Mark (Europe)
o IP55 Rated
o C-Tick (New Zealand/Australia/Taiwan)
 Contactless smart card readers shall meet the following environmental specifications:
o Operating temperature: -30 to 150 degrees F (-35 to 65 degrees C)
o Operating humidity: 5% to 95% relative humidity non-condensing
o Weatherized design suitable to withstand harsh environments
 Contactless smart card reader cabling requirements shall be:
o Cable distance: (Wiegand): 500 feet (150m)
o Cable type: 5-conductor #22 AWG with overall shield
o Standard reader termination: 18” (.5m) cable pigtail
 Warranty of contactless smart card readers shall be lifetime against defects in materials and
workmanship.
 Contactless smart card reader shall be Honeywell OM55 compatible with selected card media.

1.1.3 ACCESS CARDS (CREDENTIALS)

Provide (specify quantities) OmniClass Contactless Smart Card Credentials in the following form factors:

Document 7-501121, Revision 00 Architect and Engineering Specification

© 2005 Honeywell International. Confidential. 8 OmniClass Readers and Credentials

[Link] Access Card
Access cards shall be used with access readers to gain entry to access controlled portals (e.g.; doors,
gates, turnstiles) and to hold information specific to the user.
Provide (specify quantity) (badge protectors with clips or other accessories), of a type acceptable to the
Architect.
The card shall be available in single technology or multiple technology configurations.

[Link].1 Single Technology Cards

Single technology cards shall meet the following criteria:
 The card shall meet the following standards for contactless smart cards: ISO 15693 and ISO
14443B2.
 The card shall meet ISO 7810 specifications for length, width, thickness, flatness, card
construction and durability, and shall be in a form suitable for direct two-sided dye-sublimation
or thermal transfer printing on the specified badge printer.
 Presentation to the access control reader at any angle within a minimum of one (1) inch shall
result in an accurate reading of the card.
 Unique 64-bit, fixed card serial number, used for anti-collision and key diversification.
 The card shall support capability, with a minimum of 2 Kbits [256 bytes] of EEPROM memory
or 16 Kbits [2048 bytes] of EEPROM memory. The 2 Kbit card shall have a minimum of 2
Application Areas, and the 16Kbit shall have either (specify) 2 or 16 Application Areas to
support future applications. Data retention shall be 10 years, nominal. Wiegand card data up to 84
bits in length shall be factory programmed in Application Area 1 for use with access control
systems.
 Each Application Area on the card shall be secured with a 64-bit unique, diversified security key,
such that data stored in that area cannot be accessed or modified until the card and reader have
completed a mutual authentication process.
 The card shall be capable of completing any write operation, even if the card is removed from the
RF field during that operation.
 The card shall be warranted against defects in materials and workmanship for two (2) years, or if
multiple technologies are used: with a magnetic stripe the card shall have a fifteen (15) month
warranty; or with a contact chip, the card shall have a one (1) year warranty.
 Provide (specify quantity), “smart” access cards, compatible with the specified card readers.
Cards shall be encoded with Wiegand card data, at the factory.
 The card shall not carry any identification showing the location of the property unless otherwise
specified herein.
 The card shall be capable of accepting a slot punch on one end, allowing it to be hung from a
strap/clip in a vertical orientation.

[Link].2 Multiple Technology Cards

Multiple technology cards shall meet one (specify) of the following additional criteria:

Document 7-501121, Revision 00 Architect and Engineering Specification

© 2005 Honeywell International. Confidential. 9 OmniClass Readers and Credentials

  The card shall support 13.56 MHz OmniClass contactless smart chip and antenna plus any or all
of the following technologies, simultaneously:
o 125 kHz HID Proximity chip and antenna
o Magnetic Stripe
o Embedded Contact Smart Chip Module
 The card shall be available with a 13.56 MHz OmniClass contactless smart chip and antenna plus
a Wiegand Strip with an optional magnetic stripe, meeting all ISO 7810 standards except for card
thickness, which shall be 0.037” (0.939 mm). This card will not be available with 125 kHz
proximity technology and/or an embedded contact smart chip module.

[Link] Access Key Fob

 Access Key Fobs shall be used with access readers to gain entry to access controlled portals (e.g.;
doors, gates, turnstiles) and to hold information specific to the user.
 The Key Fob shall meet the following standards for contactless smart cards: ISO 15693 and ISO
14443B2.
 The Key Fob shall be constructed of durable injection molded polycarbonate plastic, with a slot
molded into one end, and shall be suitable for placement on a key ring.
 Presentation to the access control reader at any angle within one (1) inches shall result in an
accurate reading of the key fob.
 Provide (specify quantity) key fobs compatible with the specified card readers.
 The key fob shall not carry any identification showing the location of the property unless
otherwise specified herein.
 The key fob shall be warranted against defects in materials and workmanship for two (2) years.

[Link] Access Sticker

 Access Stickers shall be used with access readers to gain entry to access controlled portals (e.g.;
doors, gates, turnstiles) and to hold information specific to the user.
 The Sticker shall meet the following standards for contactless smart cards: ISO 15693 and ISO
14443B2.
 The Sticker shall be a flat disc-shaped unit with a polycarbonate cover and a self-stick adhesive
back.
 The Sticker shall be capable of affixation to non-metallic personal items such as PDAs, cell
phones, business assets, or to existing access control or identification cards for the purpose of
transitioning from earlier technologies to contactless smart cards.
 The Sticker shall not be used with tractor-feed (full insertion) readers.
 Presentation to the access control reader at any angle within one (1) inches shall result in an
accurate reading of the Sticker.
 The Sticker shall be warranted against defects in materials and workmanship for two (2) years.
 Provide (specify quantity) Access Stickers compatible with the specified card readers.
 The Sticker shall not carry any identification showing the location of the property unless
otherwise specified herein.

Document 7-501121, Revision 00 Architect and Engineering Specification

© 2005 Honeywell International. Confidential. 10 OmniClass Readers and Credentials

Honeywell Europe Office
136 West Forest Hill Avenue Böblinger Straße 17
Oak Creek, WI 53154 D-71101 Schönaich
(414) 766-1700 Ph Germany Specifications subject to change without notice
(414) 766-1798 Fax 49-7031-637-782 © 2005 Honeywell International, All rights reserved
[Link] 49-7031-637-769 Fax Document 7-501121, Revision 00