DESIGN GUIDELINES

FOR ELECTRICAL, TELECOMMUNICATION AND

LOW-CURRENT SYSTEMS
(GENERAL)

Rev. Description Date

0 Design Guidelines march, 2025

GENERAL Electrical Services
Design Requirements

A. BUILDINGS INTERNAL ELECTRICAL, TELECOMMUNICATION AND LOW-CURRENT

SERVICES

Buildings Electrical, Telecommunication and Low-current services shall be designed and

installed as per following guidelines.

1. Follow the latest version of Electricity Wiring Regulations applicable for Local Power
Distribution Company. Also follow international standards like BS 7671, NFPA 70, NFPA
72, BS EN 62305 etc as applicable. Latest 'Estidama' design guidelines also shall be
followed.

2. Follow Etisalat, DIC and relevant international standards for telecommunication systems.
Also incorporate the requirements of the User and Signal Corps.

3. User Requirements: All systems as per specific User requirements for each facility shall
be provided. User requirements, if any, are attached with the tender documents in the
form of drawings, sketches or manuscript.

4. Check and verify the space requirements for Electrical and Telecom service rooms in the
facility. Coordinate with the architect for the incorporation of these space requirements
and also shafts for horizontal and vertical cable routing etc. as applicable.

5. Lighting: Generally follow CIBSE guidelines for lighting design. For large areas and
typical rooms give design calculations to verify that recommended illumination levels are
achieved.
Energy efficient light sources shall be considered. High efficiency T5 linear fluorescent
tube, compact fluorescent lamp and LED light fixtures with low-loss electronic ballasts
shall be considered. For high bay and external lighting use metal halide lamp light
fittings. All light fixtures shall conform to BS EN 60598.
Following Illumination levels can be considered for certain specified areas:
(This is for general guidance only and for detailed information follow CIBSE guidelines.)

Offices, Meeting Rooms, Classrooms, Workshops : 600Lux

Elect. Room, Communication Room, Mech. Rooms,

Kitchen : 400Lux

Reception, Lobby, Lecture Hall,

Prayer Hall, Bedrooms, Majlis, Café, Dining : 300Lux

Corridors, Store : 200Lux

Toilets : 120Lux

Indoor Sports Halls : 500Lux

Directorate of Military Works Rev. 0 Page 2 of 14

GENERAL Electrical Services
Design Requirements

6. Fire Alarm System:

Fire Alarm system shall be provided for all buildings as per following:

a) System shall be analogue addressable.

b) System design shall conform to latest issue of BS5829, NFPA 72 and local civil
defence regulations.
c) Alarm management shall be field configurable. All components of the system
including sensors, manual call points, bells etc. shall be addressable. All components
to be monitored.
d) Control panel to be microprocessor based. Completely contained, tropicalized type.
To have zone isolation facility, individual zones fault and fire signals etc. and have
signal test feature. All signals to be LED. Panel to have provision to connect to a full
function repeater panel. Panel to have control keypad and backlit LCD dot-matrix
display. Cards to be plug-in type. Panel to have one spare loop, terminals and
adequate working space.
e) The charger and battery capacity to be adequate. Batteries to be sealed long life
maintenance-free type and have a self power time of 30 minutes with all input and
output devices working. Provide matching recessed extension box below control
panel for batteries, as needed.
f) Detection to be by smoke, heat, multi-sensors as adequate. Also provide A/C duct
sensors with remote LED indication. Provide LED response indicators over doors of
rooms for quick monitoring. All detectors etc. and bases shall be labeled indicating its
address.
g) Provide alarm bells throughout the facility, weatherproof strobe and siren externally.
Alarm delay adjustable on siren. Also provide voice evacuation and fireman's
telephone jack etc. as per civil defence requirements.
h) Installation shall be by silicon rubber, high fire temperature resistant, stranded
copper wiring through concealed PVC conduits or surface GI conduits as per site
conditions.
i) The system shall be interlocked with HVAC system. Provide interface and wiring to
this effect to concerned equipment and BMS.
j) In case of a fire condition the panel shall
k) automatically dial and inform, in English and Arabic, a designated telephone number
of Fire Section/Guard Room. For this purpose, provide a connection to nearby
telephone outlet. Panel should have a back confirmation facility for this function.
l) Provide zoning chart and operating instructions in framed glass near control panel.

7. Communication and Data Network

Communication and data networking shall be provided for all buildings as per
following:
a) RJ45 Voice, Data or dual Voice/Data outlets connected to MDF/IDF by Cat 6
screened copper cable in a star topology. The maximum length of this cable
shall be limited to 90m. Concealed cable containment preferred.
b) Intermediate Distribution Frames (IDF) consisting of RJ45 patch panels, patch
chord's passive ancillary components and space for active components.
Connected to MDF by multicore Cat 3 voice cables and multimode fiber optic
cables in a redundant formation.
c) Main Distribution Frame (IDF) consisting of RJ45 patch panels, patch chords,
passive ancillary components and space for active components.

Directorate of Military Works Rev. 0 Page 3 of 14

GENERAL Electrical Services
Design Requirements

d) Heavy duty return flange GI slotted cable trays for horizontal and vertical
cabling inside the buildings.
e) Dedicated Communication Rooms to house the IDF/MDF. Air-conditioned and
with raised floor. Provision of external cable entry for the MDF Room, minimum
4 no. 100mm dia. pipes.
f) It shall be noted that telephone handsets, active transmission and exchange
equipment, data servers and external fiber optic network cabling will be
procured later by others.

8. IF Satellite Antenna Distribution System

IF satellite antenna distribution system shall be provided for following buildings:
Officers' Accommodation, NCOs Accommodation, Officer Mess, Common Mess,
Headquarter Building, Sport Hall, Club, Recreation Facilities and for any other
buildings as specified elsewhere.
The system shall be independent for each building and to be as per following:
a) The system shall distribute the IF signals from the central dish antennas to the
domestic receivers (Receivers will be procured later by others). Each receiver
to tune-in all channels independently. The polarization control at each outlet
shall be by receiver LNB voltage. Each outlet shall be separately connected to
switcher in a radial topology.
b) Central Dish Antennas
- 120cm Ku band dish antenna for Nilesat complete with LNB and feed horn.
- 120cm Ku band dish antenna for Arabsat 3A complete with LNB and feed
horn.
Antennas shall be installed on a suitable base and support on the roof or at
an ideal location as per site conditions.
c) Multiswitches/Launch Amplifiers/Line Amplifiers
Cascadable multiswitches with multi inputs and 4/8/16 outputs as per system
design. Launch amplifier and line amplifiers as per requirements. All
equipment shall be double shielded and shall be installed inside the Electrical
Rooms.
d) 'F' type satellite antenna socket outlet for connection to a satellite receiver,
white PVC face plate. Each face plate shall be labeled for its unique serial
number.
e) Low-loss type coaxial cabling through concealed conduits. Maximum loss for
trunk feeders shall be 12dB/100m@800MHz and 18dB/100m@800MHz for
socket wiring. Adequate signal level of not less than 55dB shall be
maintained at each outlet.

9. AUDIO_VISUAL SYSTEM
AV system shall be provided for Theatre Hall, Lecture Hall and for any other
buildings and areas as specified elsewhere.
A fully integrated Audio-visual system, professional type, of latest technology,
upgradeable and shall consist of following as minimum:

a) Overhead multimedia installation projector, DLP or inorganic 3 LCD

technology, 1920x1080 full HD 1080p resolution, HDMI and network RJ45
connectivity, powered short focus zoom lens, auto iris, minimum 6000 to
20000ANSI lumens brightness in standard mode (according to the size of the

Directorate of Military Works Rev. 0 Page 4 of 14

GENERAL Electrical Services
Design Requirements

screen and hall, as per design calculations), 3000 hour or more long life
multiple lamps, Xenon lamps if required, quiet operation (less than 33dBA)
and easy maintenance, network management and hand held remote control
unit for all functions.
b) Electric projection screen, wall mounted, 16:9 aspect ratio, white matt
material, quiet operation, interfacing for automatic operation, wired controls
and hand held remote control unit.
Nominal screen size as per requirements.
c) Blueray player with USB digital media input.
d) Digital audio processors and audio amplifiers for 5.1 channel digital surround
sound system, stereo wireless mic and receiver, wall mounted DSP line array
speakers inside the Hall. Power output of amplifiers and the speakers shall
be based on sound pressure level calculations. Amplifier rack and video
switcher etc. shall be placed in the room beside the stage.
e) Proprietary lectern/podium, designer type, modern aesthetic appearance,
stainless steel/aluminium and glass construction having custom insignia,
electrically operated height adjustable mechanism, free standing over a floor-
service outlet box, low-profile lectern mic.
f) Concealed cabling. All cables and connectors shall be professional type
recommended by the manufacturer. One DVI/HDMI input of the projector
shall be connected to the video player, another shall be wired up to podium
for future connection to a portable computer, one RJ45 input shall be
connected to the LAN through a data socket provided on the ceiling, and
another RJ45 shall be wired up to the Stage. PC input and any other video
input also shall be wired up to the podium. Provide dedicated sockets for all
these connections.

10. PUBLIC ADDRESS SYSTEM

Public Address system shall be provided for the Sports hall and for any other
buildings and areas as specified elsewhere.
PA system shall be provided for the Mosque only with standard features.
Sound pressure level calculations to determine the quantity of speakers, wattage,
spacing and thereby the rated power output of amplifiers shall be based on
relevant BS or international standards. It shall be professional type, of latest
technology, upgradeable and shall consist of following as minimum:

a) System Rack: Proprietary cabinet with front hinged transparent doors and
rack mounted components. (To be kept below the reception counter etc.) Pre-
amplifier mixer, USB digital media input, multi-channel power amplifiers with
all standard features, FM stereo digital tuner with programmable presets, 2
no. FM wireless mic receivers, One local desktop mic with chime, monitor
panel, LED ladder output level indicator, monitor speaker with attenuator,
input-output board units etc. All cable terminations from front face.
b) Speakers in various zones as per system design and requirements.
c) Mic plug-in sockets, one each in Sports Hall, Swimming Pool and Aerobics etc.
d) FM wireless mic,clip-on mic, floor stand etc.
e) Concealed wiring, all cables to be special type recommended by the
manufacturer. PA system calculations, Layout, block diagram etc. shall be
submitted for approval.

Directorate of Military Works Rev. 0 Page 5 of 14

GENERAL Electrical Services
Design Requirements

11. Design drawings shall be submitted for review and approval before shop drawing
submission. Submit all technical calculations, references to adopted standards and
regulations, extracts from relevant standards, catalogue cuts and other supporting
documents to justify the design. References shall be given to the computer software
programs used and if asked for, softcopy of the calculations along with the application
software shall be submitted. The drawings in general shall comply with the following:
a) Verify that the background drawings used are architecturally up to date. Also verify
that the design is based on the latest HVAC, Plumbing, and other services drawings.
b) In the power layout drawings show all the power outlets, DBs, Control Panels and
MCC for mechanical equipment; main routing of cable trays/trunking; cable entry
ducts and chambers.
c) Show circuits for all lighting and power points.
d) Give load schedules for all final DBs, SMDBs and MDB.
e) Give power riser diagram for the MDB showing up to final DBs. Mention load
details/diversity factors/voltage drop/short circuit withstand/earth fault loop
impedance/power system analysis results etc.
f) Circuit diagrams shall be furnished for LCPs and control devices for automatic
switching.
g) Detailed riser diagrams shall be furnished for all low current systems.

10. GENERAL REQUIREMENTS FOR BUILDINGS:

SYSTEM DESCRIPTION NOTES

Lighting T8 Linear Fluorescent tube batten light For Storage Rooms,
fittings, magnetic ballast. Electrical Rooms,
Mechanical Plant Rooms.
T8 Linear Fluorescent tube light fittings with For Kitchen, Common
prismatic diffuser, magnetic ballast, IP54. Toilets in
accommodations, Wet
Service/Plant Rooms,
Chemical and Sensitive
Store Rooms. (Recessed
fittings in areas of false
ceiling.)
T5 Linear Fluorescent tube 60x60cm For Pharmacy, Treatment
recessed light fittings with prismatic Room, Doctor Room and
diffuser, IP23, HF electronic ballast. Wards.
T5 Linear Fluorescent tube 60x60cm For Offices, Classrooms,
recessed light fittings with double parabolic Instruction Rooms,
specular mirror louvers, HF electronic Operation Rooms,
ballast. Meeting Rooms,
Communication Rooms
and similar areas.
T5 Linear Fluorescent tube 60x60cm For Offices etc. where
recessed light fittings with double parabolic daylight based automatic
specular mirror louvers, dimmable HF dimming is required.
electronic ballast.
T5 Linear Fluorescent lamp Mirror lights For all wash basins.
with diffuser and IP55, HF electronic

Directorate of Military Works Rev. 0 Page 6 of 14

GENERAL Electrical Services
Design Requirements

SYSTEM DESCRIPTION NOTES

ballast.
Compact Fluorescent (CF) lamp down For Entrance Lobby,
lights with anodized aluminium reflector Reception, Corridors.
optics, HF electronic ballast.
Compact Fluorescent (CF) lamp down For Lecture hall, Theatre
lights with anodized aluminium reflector and also for areas where
optics, dimmable HF electronic ballast. daylight based automatic
dimming is required.
CF lamp decorative ceiling lights, HF For Bedrooms
electronic ballast.
CF lamp IP44 down lights, HF electronic For Dining Rooms
ballast.
CF lamp IP54 down lights, HF electronic For Bath and Toilets.
ballast.
High power LED down lights. For decorative Offices and
Entrance Lobby etc. in
combination with
fluorescent lights.
High power LED adjustable spot lights. For wall displays and
other specific applications.
Metal halide high bay lights and projector For high bay Workshops,
type flood lights. Warehouses and Sports
Halls.
T5 Linear fluorescent tube tamper proof For the detention Cells.
light fittings.
External vandal resistant fittings. As specified elsewhere.
CF or Metal halide ceiling/down lights to For external fascia and
IP54. entrance area lighting of
Decorative Metal halide wall brackets to all buildings as applicable.
IP54.
Bulkhead type Metal halide wall mounted
down lights to IP54.
Metal halide projector type flood lights.
Metal halide buried uplighters.
RYB LED strip lights, high power LED
accent, spot and uplighters.
Emergency and T5 Linear Fluorescent lamp, electronic
Exit Lighting ballast emergency lights.
Self contained and non-maintained For all areas as per
emergency lights. standard practice.
Maintained/Non-maintained Exit lights. Achieved illumination level
Emergency power pack fitted with normal as per regulations.
lighting fixtures.

Switching White plastic finish for all

general areas.
10/20A local control switches.
Weather proof and metal-
(For all general areas.)

Directorate of Military Works Rev. 0 Page 7 of 14

GENERAL Electrical Services
Design Requirements

SYSTEM DESCRIPTION NOTES

clad weatherproof for wet
and external areas, plant
rooms etc. as applicable.
For Theatre Hall,
Dimming control stations. Auditoriums, Lecture hall
etc.
For skylighted areas and
Daylight based automatic Dimming control
areas with suntube
with override control stations.
lighting method.
Motion detection based automatic switching For corridor lights and as
with local override facility. specified elsewhere.

For all toilets and

Motion detector with 2000W switching unit
bathrooms.
and local override switch.

Time delay switches For stairs.

Local ON/OFF pushbuttons controlling the For high bay area and
lights through LCP with relays/contactors. sports halls.

Integral photocell switching for external For entrance area lighting

lights. as per requirements.

Daylight + Timer based automatic

switching. For all external lights.

13A single and 2-gang switch-socket

outlets for general use in all areas.
(Quantity as per ADDC recommendations.)
For all facilities.
One dedicated 13A 2-gang switch-socket White plastic finish for all
outlet beside each satellite antenna outlet. general areas.
Weather proof and metal-
One dedicated 13A 2-gang switch-socket clad weatherproof for wet
outlet beside each voice/data outlet. and external areas, plant
rooms etc. as applicable.
Power Supply (Please refer to Telecommunication section
for the quantity of RJ45 and fiber optic
outlets.)
13A ceiling mounted SSO controlled by a For overhead projector in
20A DP switch installed at low level. Meeting Room.
20A DP switches with neon indication for all
stand-alone water heaters.
For all facilities as
applicable.

Power supply for all HVAC Equipment, White plastic finish for all
Refrigeration Equipment, Kitchen general areas.
Equipment, Overhead Cranes, Air Weather proof and metal-
Compressor, Pumps, Motors, Lifts,
Directorate of Military Works
Plumbing and other mechanical
Rev. 0
equipment, Page 8 of 14
motorized doors etc. as:
GENERAL Electrical Services
Design Requirements

SYSTEM DESCRIPTION NOTES

Control switches clad weatherproof for wet
Switch-socket outlets and external areas, plant
Flex outlets rooms etc. as applicable.
Isolators
Motor Control Centres
Control panels,
Power Supply Dedicated DBs etc.
230V, 50Hz, Ph+N+E, 3 Pin industrial type
switchsocket outlets or isolators. As specified elsewhere.

400V, 50Hz, 3Ph+N+E, 5 Pin industrial type

switchsocket outlets or isolators. As specified elsewhere

DC, 2 Pin industrial type switchsocket

outlets with integral solid state DC power As specified elsewhere
supply unit fed by mains supply.
For each facility in the
One no. 32A, 400V, 50Hz 3 Phase Isolator. main Network/
Communication Room.

UPS systems As specified elsewhere

Power conditioners/stabilizers. As specified elsewhere

Generators/converters for Special power As specified elsewhere

supply and power distribution system.
(DC, 60Hz, 400Hz etc.)

Surge arrestors As specified elsewhere

As per design requirement

in all facilities.
Final DBs with MCCB incomer. Single or Split busbar type
with appropriate earth
leakage protections.
As per design requirement
in all facilities as
applicable.
SMDBs Incorporate earth leakage
protections where
applicable.
Form 2.
In all facilities.
Main DBs of 250A and
above to have Voltmeter
Main DB with MCCB incomer up to 1000A
+ selector switch and 3
and ACB incomer for 1200A and above.
Ammeters.
Incorporate earth leakage
protections where

Directorate of Military Works Rev. 0 Page 9 of 14

GENERAL Electrical Services
Design Requirements

SYSTEM DESCRIPTION NOTES

applicable.
Form 2, Type 2 normally.
Form 3 or Form 4 if
specified elsewhere.
IP rating as per
application areas.
Tele- Dual RJ45 voice + data outlets. One no. for every 4
communication (Connected to IDF/MDF by Cat 6 screened square metre of office
(Voice and Data) cables) space.
One no. each for
Reception, Meeting
Room, Bedroom, Majlis,
Cafe, Dining Room,
Guard Room, Store etc.

2 no. each in the

Treatment room, Doctor
Room and Pharmacy etc.

2 no. each for every one

linear meter of worktop of
laboratories etc.
1 no. each for the internet
desk.
Single SC/SC optical fiber 50/125 As specified elsewhere
multimode socket outlets.
(Connected to MDF/IDF by 2 core
multimode fiber optic cable.)

Dual RJ45 voice outlets. (Connected to 1 no. each in the

IDF/MDF by Cat 6 screened cables) Kitchnette.

RJ45 data outlets. One no. for the overhead

(Connected to IDF/MDF by Cat 6 screened projector in the Meeting
cables) Room etc.
IDF As per design
(For details refer Note-7) requirements.

MDF Located in the Ground

(For details refer Note-7) Floor Communication
Room in all facilities.
MDF Located near the entrance
(For details refer Note-7) areas at a convenient
location in facilities
without communication
rooms.
Fire Alarm Analogue addressable system For all areas.
System (Refer Note-6).

Directorate of Military Works Rev. 0 Page 10 of 14

GENERAL Electrical Services
Design Requirements

SYSTEM DESCRIPTION NOTES

F-type satellite signal outlets for connection One no. in each Bedroom.
to a receiver. (Receiver by Others) One no. each in the
Coffee Shop, Hairdressing
Sitting and Dining.
One no. in the Meeting
IF Satellite
Room.
Antenna System
One no. in each Hospital
Ward.
Dish antennae for Nilesat and Arabsat Separate antennas for
each building having the
system.
Earthing System Local earthing for facility
MDB.
One no. earth bar in the
Ground Floor
Network/Communication
Room of each facility.

As specified
Access control elsewhere.
system
CCTV system As specified elsewhere

ATS and As specified elsewhere

Standby Diesel
Generator Sets

Intruder alarm For ammunition stores.

and over- As specified
temperature elsewhere.
warning system.

Lightning The system design shall conform to BS EN For G+3 and higher
Protection 62305 buildings, Ammunition
System Facilities.
Hangars, Workshops etc.
as specified.

B. EXTERNAL ELECTRICAL AND TELECOMMUNICATION SERVICES

1. External Lighting

a) Walkway Lights:
For walkways
5m high aluminium Pole with 1 no. 100W metal halide lamp decorative light fitting
at a spacing of 20m approx.

Directorate of Military Works Rev. 0 Page 11 of 14

GENERAL Electrical Services
Design Requirements

b) Road Lights:
For dual carriage way - Double arm, 12m high GI Pole with 2 no. 400W metal
halide lamp canopy type fittings at a spacing of 36m approx.

For single carriage way - Single arm, 12m high GI Pole with one no. 400w metal
halide lamp canopy type light fittings at a spacing of 36m approx.

c) Security Lights:
All around the external boundary.
12m high GI Pole with 2 no. 400w high pressure sodium lamp projector type light
fittings at a spacing of 60m approx.

d) Entrance Gate Lights:

12m high GI Pole with 2 no. 1000w metal halide projector type light fittings with
local control switches – one for each entrance gate and fed from the DB of Guard
Room by a 4 core 10mm2 Cu/XLPE/SWA/PVC cable and earth continuity cable.

e) Play Ground and Parade Ground Lights:

Metal halide flood light projectors on GI pole/masts.
Required illumination level or lamp wattage, quantity and pole height as mentioned
elsewhere.

f) Lighting Control Panels:

Photocell and timer controlled for Road/Security lighting, manual pushbutton
controlled for
Play ground and parade ground lighting.

g) Circuit Cabling: -
4 core Cu/XLPE/SWA/PVC cables, as per voltage drop requirements.
The maximum voltage drop from power source (substation) to the last pole shall be
limited to 4%.

h) Circuit Earthing: -
Last pole of each circuit shall be locally earthed.
LCP, Feeder pillar etc. to be locally earthed.

i) Solar Street Lights (If specified elsewhere)

Strreet lights with energy saving lamps and integral PV Solar power panel with
battery and controller etc.

2. Power Feeding

a) Substations/Package Substations:
MV/400V Substations or Package Substations shall be provided for the power
supply to the project.

b) MV Ring Feeder Cabling:

MV Ring feeder cabling shall be provided from power source to the site as per local
power supply authority recommendations.

Directorate of Military Works Rev. 0 Page 12 of 14

GENERAL Electrical Services
Design Requirements

c) Coordination with Local Power Supply Authority

Coordinate with Local Power Supply Authorities for all matters related to power
supply and for the Load Demand Notification.
(Unless mentioned otherwise, power connection charges are not in the
Contractor's scope.)

d) Coordination with Municipality/Town Planning

Coordinate with Municipality, Town Planning Department or other concerned
authorities for service reservations and other related matters etc. and obtain
necessary approvals as and where necessary.

e) Coordination with Service Providers

Coordinate with various service providers and incorporate their requirements as
applicable.

f) Energy Metering
Provide kWh meter as per the requirements of Local Power Supply Authorities.

g) LV Power Feeding:
LV Power feeding shall be provided up to the Main DB of each facility. LV feeder
cables shall be 4 core Cu/XLPE/SWA/PVC 600/1000VGrade.

h) LV Power Feeding:
LV Power feeding shall be provided to all new facilities and to any related ancillary
facilities such as chiller yard, pump rooms, substations etc. related to the project.

Feed bigger facilities directly from substations. Feed all other facilities through
Feeder Pillars which in turn shall be directly fed from the substations.

External LV Feeder Pillars shall be generally with 50kA MCCB incomer and
outgoings. Rating and quantity to be as per design requirements.

The power feeding cables shall be sized according to load and voltage drop
calculations. The maximum voltage drop from power source (substation) to the
building MDB shall be limited to 3%. The voltage drop shall be calculated based on
the demand load.

i) Standby Generator
Standby diesel generator set and ATS as specified elsewhere.

j) Existing Services
Any existing electrical and telecom services affected by new constructions shall be
removed/relocated/rerouted as per site requirements.

3. External Telecom Duct Network

External duct and manhole network interlinking all the buildings. It shall be 8 no.
100mm UPVC pipes for the main artery and 4 no. 100mm UPVC pipes for the branch
runs.
The manholes for main artery (along the dual carriage way) shall be JRC12 and for
branch runs it shall be standard manholes. All manholes at building entry points shall
be provided with an insulated earth bar connected to an earth pit.

Directorate of Military Works Rev. 0 Page 13 of 14

GENERAL Electrical Services
Design Requirements

It shall also be connected to existing network as per site conditions.

(Network cabling will be procured later by others).

4. External Fire Alarm Networking

A fire alarm repeater panel shall be installed and connected in the existing main Guard
Room to repeat fire alarm signals in all other facilities. The signals to be repeated are
'Power ON', 'Fault' and 'Fire' for each facility. Interconnected network cabling can be laid
through one of the Telecom Ducts mentioned in above paragraph with proper labeling
throughout.

5. PV Solar Power Generation (If specified elsewhere)

Solar PV cell array stand-alone power generation systems with or without battery.

---\---\---

Directorate of Military Works Rev. 0 Page 14 of 14