STAATSKOERANT, 29 Januarie 2025 No.

52012   3

General Notices • Algemene Kennisgewings

DEPARTMENT OF TRADE AND INDUSTRY

DEPARTMENT OF TRADE, INDUSTRY AND COMPETITION
No. 2025
NOTICE 2949 OF 2025
STANDARDS ACT, 2008
STANDARDS MATTERS
In terms of the Standards Act, 2008 (Act No. 8 of 2008), the Board of the South African Bureau of Standards has acted in
regard to standards in the manner set out in the Schedules to this notice.

SECTION A: DRAFTS FOR COMMENTS

The following draft standards are hereby issued for public comments in compliance with the norm for the development of
the South Africa National standards in terms of section 23(2)(a) (ii) of the Standards Act.

Draft Standard No. Closing

Title, scope and purport Date
and Edition
Live and chilled raw bivalve molluscs. This standard applies to live and chilled raw
bivalve molluscan shellfish and to raw chilled bivalves either in the round, or
SANS 2879:20XX
shucked and cleaned for direct consumption or for further processing (hereafter 2025-02-26
Ed 1
referred to as ʺbivalvesʺ).

Small craft — Watertight or quick-draining recesses and cockpits. This document

SANS 11812:20XX
specifies watertightness, draining time and sill heights requirements for watertight 2025-02-26
Ed 2
and quick-draining recesses and cockpits in small craft of up to 24 m load line
length (see Reference [1]).
Arc welding equipment Part 2: Liquid cooling systems. This part of IEC 60974
SANS 60974-2:20XX specifies safety and construction requirements for industrial and professional
2025-02-26
Ed 3 LIQUID COOLING SYSTEMS used in arc welding and allied processes to cool
torches.
SANS 14001:20XX Environmental management systems — Requirements with guidance for use. This 2025-03-29
Ed 3 International Standard specifies the requirements for an environmental management
system that an organization can use to enhance its environmental performance. This
International Standard is intended for use by an organization seeking to manage its
environmental responsibilities in a systematic manner that contributes to the
environmental pillar of sustainability
SANS 19443:20XX Quality management systems — Specific requirements for the application of 2025-03-29
Ed 1 ISO 9001:2015 by organizations in the supply chain of the nuclear energy sector
supplying products and services important to nuclear safety (ITNS). This
International Standard specifies requirements for a quality management system
when an organization:
a) needs to demonstrate its ability to consistently provide products and services that
meet customer and applicable statutory and regulatory requirements, and
b) aims to enhance customer satisfaction through the effective application of the
system, including processes for improvement of the system and the assurance of
conformity to customer and applicable statutory and regulatory requirements
SATS 17012:20XX Conformity assessment — Guidelines for the use of remote auditing methods in 2025-03-29
Ed 1 auditing management systems. This document provides guidance on the use of
remote auditing methods in auditing management systems. It is applicable to all
organizations that plan and conduct all kinds of internal or external audits (i.e. first-
party, second-party and third-party audits) of management systems
SANS 8309:20XX Standard guide for stability testing of cannabis-based products. This guide is 2025-03-29
Ed 1 applicable to commercial processors and manufacturers engaged in the processing,
testing, packaging, labelling, and storage of cannabis products intended for human
consumption, including those derived from hemp. Hemp seed and products derived
from hemp seed are excluded from the scope of this guide This guide describes the
minimum requirements for conducting stability testing of new cannabis products
with the purpose of determining appropriate storage conditions and shelf-life.
SANS 8398:20XX Standard practice for management responsibilities in managing a quality 2025-03-29
Ed 1 management system (QMS). This practice provides the management responsibilities
for the implementation and oversight of a quality management system (QMS). It

This gazette is also available free online at www.gpwonline.co.za

4  No. 52012 GOVERNMENT GAZETTE, 29 January 2025

can be applied to all cannabis operations, including cultivation, manufacturing,

labelling, dispensing, and distribution. This practice does not address the quality
management system details, but rather focuses on the main considerations
for management’s role in setting up a QMS. Guide D8222 provides an overview
and some details about the components of a QMS. Other standards provide details
on specific QMS components
SANS 19662:20XX Milk — Determination of fat content — Acido-butyrometric (Gerber method). This 2025-03-29
Ed 1 document specifies a method, the acido-butyrometric or “Gerber”, for determining
the fat content of milk. It is applicable to whole milk and partially skimmed milk.
SANS 19160-2:20XX Addressing Part 2: Assigning and maintaining addresses for objects in the physical 2025-03-29
Ed 1 world. This document focuses on assigning and maintaining addresses that allow
the unambiguous determination of an object in the physical world for purposes of
identification and location in the context of public administration and public service
delivery. During assignment, an address is first associated with a particular object
in the physical world. During maintenance, the address changes, for example, it is
re-assigned to a different object, one or more of the address components are
modified (e.g. a street name change), or the address is retired when it is no longer
used. This document
SANS 38503:20XX Information technology — Governance of IT — Assessment of the governance of IT. 2025-03-29
Ed 1 This document provides guidance on the assessment of governance of information
technology (IT) based on the principles, definitions and model for the governance
of IT outlined in ISO/IEC 38500 and ISO/IEC TR 38502 and the implementation
considerations outlined in ISO/IEC TS 38501. This document includes approaches
for conducting the assessment, the criteria against which the assessment can be
made, guidance on the evidence that can be used for the assessment, as well as a
method for determining the maturity of the organization’s governance of IT. This
document is applicable to organizations of all sizes, regardless of the extent of their
use of IT.
SANS 38507:20XX Governance of IT — Governance implications of the use of artificial intelligence by 2025-03-29
Ed 1 organizations. This document provides guidance for members of the governing
body of an organization to enable and govern the use of Artificial Intelligence (AI),
in order to ensure its effective, efficient and acceptable use within the organization
SANS 45001:20XX Occupational health and safety management systems — Requirements with 2025-03-29
Ed 1 guidance for use. This document specifies requirements for an occupational health
and safety (OH&S) management system, and gives guidance for its use, to enable
organizations to provide safe and healthy workplaces by preventing work-related
injury and ill health, as well as by proactively improving its OH&S performance.
SANS 50001:20XX Energy management systems — Requirements with guidance for use. This 2025-03-29
Ed 2 document specifies requirements for establishing, implementing, maintaining and
improving an energy management system (EnMS). The intended outcome is to
enable an organization to follow a systematic approach in achieving continual
improvement of energy performance and the EnMS
SANS 56001:20XX Innovation management system — Requirements. This document specifies 2025-03-29
Ed 1 requirements for an innovation management system that an organization can use to
develop and demonstrate its innovation capability, enhance its innovation
performance, and realize value for users, customers and other interested parties.
The requirements in this document are generic
SANS 56008:20XX Innovation management — Tools and methods for innovation operation 2025-03-29
Ed 1 measurements — Guidance. This document provides guidance for the definition,
implementation, evaluation, and improvement of the measurements necessary to
effectively manage innovation activities in an organization. It establishes the
fundamentals of innovation operation measurements and guides their application
towards four areas

SANS 60076-19-1:20XX Power transformers. Part 19-1: Rules for the determination of uncertainties in the 2025-02-28
Ed 1 measurement of the losses of power transformers. This part of IEC 60076 defines
the procedures that are applied to evaluate the uncertainty affecting the
measurements of no-load and load losses during the routine tests on power
transformers
SANS 60269-1:20XX Low-voltage fuses. Part 1: General requirements. This part of IEC 60269 is 2025-02-28
Ed 4 applicable to fuses incorporating enclosed current-limiting fuse-links with rated
breaking capacities of not less than 6 kA, intended for protecting power-frequency

This gazette is also available free online at www.gpwonline.co.za

 STAATSKOERANT, 29 Januarie 2025 No. 52012   5

AC circuits of nominal voltages not exceeding 1 000 V or DC circuits of nominal

voltages not exceeding 1 500 V
SANS 60269-3:20XX Low-voltage fuses Part 3: Supplementary requirements for fuses for operation by 2025-02-28
Ed 4 unskilled persons (fuses mainly for household or similar applications) — Examples
of standardized systems of fuses A to F. The following additional requirements
apply to ”gG” fuses for use by unskilled persons for domestic and similar
applications with rated currents up to and including 100 A and rated voltages of up
to and including 500 V AC and 500 V DC

SANS 60269-4:20XX Low-voltage fuses. Part 4: Supplementary requirements for fuse-links for the 2025-02-28
Ed 4 protection of semiconductor devices. IEC 60269-1 applies with the following
supplementary requirements. Fuse-links for the protection of semiconductor
devices shall comply with aIl requirements of IEC 60269-1, if not otherwise
indicated hereinafter, and shall also comply with the supplementary requirements
laid down below
SANS 62552-2:20XX Household refrigerating appliances — Characteristics and test methods — Part 2: 2025-02-28
Ed 1 Performance requirements. This part of IEC 62552 specifies the essential
characteristics of household and similar refrigerating appliances cooled by
internal natural convection or forced air circulation, and establishes test
methods for checking these characteristics
SANS 62196-6:20XX Plugs, socket-outlets, vehicle connectors and vehicle inlets — Conductive charging 2025-02-28
Ed 1 of electric vehicles Part 6: Dimensional compatibility requirements for DC pin and
contact-tube vehicle couplers intended to be used for DC EV supply equipment
where protection relies on electrical separation. This part of IEC 62196 is
applicable to vehicle connectors, vehicle inlets and cable assemblies for
electric vehicle (EV), intended for use in conductive charging systems which
incorporate control means, with a rated operating voltage up to 120 V DC
and rated current up to 100 A
SANS 62561-7:20XX Lightning protection system components (LPSC) Part 7: Requirements for earthing 2025-02-28
Ed 3 enhancing compounds. This part of IEC 62561 specifies the requirements and
tests for earthing enhancing compounds producing low resistance of an
earth termination system
SATS 62271-314:20XX High-voltage switchgear and controlgear Part 314: Direct current disconnectors 2025-02-28
Ed 1 and earthing switches. This part of IEC 62271, which is a Technical
Specification, applies to high-voltage direct current disconnectors and
earthing switches, designed for indoor and outdoor installations and for
operation on HVDC transmission systems having direct voltages of 100 kV
and above
SANS 60364-7- Low-voltage electrical installations Part 7-710: Requirements for special 2025-03-29
710:20XX installations or locations — Medical locations. The particular requirements of
Ed 1 this part of IEC 60364 apply to electrical installations in medical locations so
as to provide safety of patients and medical staff. These requirements refer
to
SANS 20000-11:20XX Information technology — Service management Part 11: Guidance on the 2025-02-28
Ed 1 relationship between ISO/IEC 20000-1 and service management frameworks:
ITIL®.This document provides guidance on the relationship between
ISO/IEC 20000–1 and a commonly used service management framework,
ITIL 4. It can be used by any organization or person wishing to understand
how ITIL can be used with ISO/IEC 20000–1, including
SANS 20000-10:20XX Information technology — Service management Part 10: Concepts and vocabulary. 2025-02-28
Ed 1 This document describes the core concepts of ISO/IEC 20000 (all parts),
identifying how the different parts support ISO/IEC 20000-1:2018 as well as
the relationships between ISO/IEC 20000-1 and other International
Standards and Technical Reports. This document also includes the
terminology used in all parts of ISO/IEC 20000, so that organizations and
individuals can interpret the concepts correctly

SANS 61557-9:20XX Electrical safety in low voltage distribution systems up to 1 000 V AC and 1 500 V 2025-03-29
Ed 2 DC — Equipment for testing, measuring or monitoring of protective measures Part
9: Equipment for insulation fault location in IT systems. This part of IEC 61557
specifies the requirements for the insulation fault location system (IFLS) that
localizes insulation faults in any part of the system in unearthed IT AC

This gazette is also available free online at www.gpwonline.co.za

6  No. 52012 GOVERNMENT GAZETTE, 29 January 2025

systems and unearthed IT AC systems with galvanically connected DC

circuits having nominal voltages up to 1 000 V AC, as well as in unearthed
IT DC systems with voltages up to 1 500 V DC, independent of the
measuring principle
SANS 60947-5-7:20XX Low- voltage switchgear and controlgear Part 5-7: Control circuit devices and 2025-02-28
Ed 2 switching elements — Proximity devices with analogue output. This part of IEC
60947 states the requirements for proximity devices that correspond to the
scope of IEC 60947-5-2:2019 with analog output (PDAO) and/or a digital
output to transmit a corresponding digital value representing the detected
sensing input. These devices can provide additional parameters. Figure 1
shows the schematic principle of such a device. They might consist of one
or more parts
SATS 62271-5:20XX High-voltage switchgear and controlgear Part 5: Common specifications for direct 2025-02-28
Ed 1 current switchgear and controlgear. This part of IEC 62271, which is a
Technical Specification, applies to DC switchgear and controlgear designed
for operation on HVDC transmission systems having direct voltages of 100
kV and above
SANS 63472:20XX Plugs, socket-outlets, vehicle connectors and vehicle inlets — Conductive charging 2025-02-28
Ed 1 of electric vehicles — Dimensional compatibility description for configuration FF
AC/DC contact-tube vehicle coupler. This document describes dimensional
options for CONFIGURATION FF AC/DC contact-tube vehicle couplers as
defined in IEC 62196-3. These possibilities serve to improve the reliability of
a mated connection when the charging cable is not axially constrained. The
options can be implemented optionally and maintain mating compatibility
with CONFIGURATION FF according to IEC 62196-3
SANS 1433-1:20XX Electrical terminals and connectors Part 1: Terminal blocks having screw and 2025-02-28
Ed 2 screwless terminals. This part of SANS 1433 covers terminal blocks having
screw type or screwless type clamping units for the connection of copper
conductors having a rated area not exceeding 300 mm2 for the screw type
and not exceeding 35 mm2 for the screwless type, and intended for use in
installations having nominal a.c. voltages of r.m.s. value not exceeding 1
000 V and frequencies not exceeding 60 Hz, or nominal d.c. voltages not
exceeding 1 500 V
SANS 16388:20XX Information technology - Automatic identification and data capture techniques - 2025-03-29
Ed 2 Code 39 bar code symbology specification.. This document specifies the
requirements for the bar code symbology known as Code 39. This
document specifies Code 39 symbology characteristics, data character
encodation, dimensions, tolerances, decoding algorithms and parameters to
be defined by applications. This document specifies the symbology identifier
prefix strings for Code 39 symbols
SANS 62752:20XX In-cable control and protection device (IC-CPD) for mode 2 charging of electric 2025-02-28
Ed 1 road vehicles. This International Standard applies to in-cable control and
protection devices (IC-CPDs) for mode 2 charging of electric road vehicles,
hereafter referred to as "IC-CPD", including control and safety functions
SANS 60947-5-1:20XX Low-voltage switchgear and control gear Part 5-1: Control circuit devices and 2025-02-28
Ed 5 switching elements — Electromechanical control circuit devices. This part of IEC
60947 applies to control circuit devices and switching elements intended for
controlling, signalling, interlocking, etc., of switchgear and controlgear
SANS 61095:20XX Electromechanical contactors for household and similar purposes. This document 2025-02-28
Ed 1 applies to electromechanical air break contactors for household and similar
purposes provided with main contacts intended to be connected to circuits
the rated voltage of which does not exceed 440 V AC (between phases)
with rated operational currents less than or equal to 63 A for utilization
category AC-7a, and 32 A for utilization categories AC-7b, AC-7c and AC-
7d (expressed in rated power), and rated conditional short-circuit current
less than or equal to 6 kA.
SANS 60669-2-4:20XX Switches for household and similar fixed electrical installations Part 2-4: 2025-02-28
Ed 2 Particular requirements — Isolating switches. This part of IEC 60669 applies to
manually operated general purpose isolating switches with a rated voltage
not exceeding 440 V and a rated current not exceeding 125 A, intended for
household and similar fixed electrical installations, either indoors or
outdoors.

This gazette is also available free online at www.gpwonline.co.za

 STAATSKOERANT, 29 Januarie 2025 No. 52012   7

SANS 62561-5:20XX Lightning protection system components (LPSC) Part 5: Requirements for earth 2025-02-28
Ed 3 electrode inspection housings and earth electrode seals. This part of IEC 62561
specifies the requirements and tests for earth electrode inspection housings
(earth housings) installed in the earth and for earth electrode seals
SANS 63454:20XX Conductive charging of electric vehicles — DC vehicle coupler configuration GG. 2025-02-28
Ed 1 This document is applicable to vehicle couplers with pins and contact-tubes
of standardized configuration (GG), herein also referred to as "accessories",
intended for use in electric vehicle conductive charging systems which
incorporate control means, with rated operating voltage and current in
accordance with IEC 62196-1:2022
SANS 63404:20XX Switchgear and controlgear and their assemblies for low voltage — Integration of 2025-02-28
Ed 1 radiocommunication device above 380 MHz into an equipment. This document
defines radiocommunication related requirements for equipment intended to
integrate a radiocommunication device. It includes the initial integration and
update of a the radiocommunication device, having a carrier frequency
greater than 380 MHz, into new or updated host equipment with
SANS 60332-3-10:20XX Tests on electric and optical fibre cables under fire conditions Part 3-10: Test for 2025-03-29
Ed 2 vertical flame spread of vertically-mounted bunched wires or cables — Apparatus.
This part of IEC 60332 details the apparatus and its arrangement and
calibration for methods of test for the assessment of vertical flame spread of
vertically-mounted bunched wires or cables, electrical or optical, under
defined conditions.
SANS 60332-3-21:20XX Tests on electric and optical fibre cables under fire conditions Part 3-21: Test for 2025-03-29
Ed 2 vertical flame spread of vertically-mounted bunched wires or cables — Category A
F/R. This part of IEC 60332 covers category A F/R for methods of test for
the assessment of vertical flame spread of vertically-mounted bunched
wires or cables, under defined conditions

SANS 60332-3-24:20XX Tests on electric and optical fibre cables under fire conditions Part 3-24: Test for 2025-03-29
Ed 2 vertical flame spread of vertically-mounted bunched wires or cables — Category C.
This part of IEC 60332 covers category C for methods of test for the
assessment of vertical flame spread of vertically mounted bunched wires or
cables, electrical or optical, under defined conditions
SANS 60332-3-25:20XX Tests on electric and optical fibre cables under fire conditions Part 3-25: Test for 2025-03-29
Ed 2 vertical flame spread of vertically-mounted bunched wires or cables — Category
D. This part of IEC 60332 covers category D for methods of test for the
assessment of vertical flame spread of vertically mounted bunched wires or
cables, electrical or optical, under defined conditions
SANS 61800-7- Adjustable speed electrical power drive systems Part 7-201: Generic interface and 2025-03-29
201:20XX use of profiles for power drive systems — Profile type 1 specification. This part of
Ed 2 IEC 61800 specifies profile type 1 for power drive systems (PDS). Profile type 1
can be mapped onto different communication network technologies.
SANS 7812-2:20XX Identification cards - Identification of issuers Part 2: Application and registration 2025-03-29
Ed 5 procedures. This document specifies the application and registration procedures for
Issuer Identification Numbers (IINs) issued in accordance with ISO/IEC 7812-1.
SANS 8502-3:20XX Preparation of steel substrates before application of paint and related products - 2025-03-29
Ed 2 Tests for the assessment of surface cleanliness Part 3: Assessment of dust on steel
surfaces prepared for painting (pressure-sensitive tape method). This part of ISO
8502 describes a method for the assessment of dust remaining on cleaned steel
surfaces prepared for painting. It provides pictorial ratings for the assessment of the
average quantity of dust. It also provides descriptive classes for the assessment of
the average size of the dust particles
SANS 1433-2:20XX Electrical terminals and connectors Part 2: Flat push- on connectors. This part of 2025-02-28
Ed 2 SANS 1433 covers flat push-on connectors, comprising rectangular tabs and their
mating receptacles, intended for use in a.c. and d.c. medium and low voltage
electrical circuits and having various maximum operating temperatures up to 300
°C
SANS 8250:20XX Standard Practice for Applying a Hazard Analysis Critical Control Points 2025-03-29
Ed 1 (HACCP) System for Cannabis Consumable Products. This practice addresses the
principles to follow when implementing and managing a Hazard Analysis Critical
Con- trol Point (HACCP) system for cannabis consumable products. This practice
is not intended for cannabis industrial products (e.g., hemp products).

This gazette is also available free online at www.gpwonline.co.za

8  No. 52012 GOVERNMENT GAZETTE, 29 January 2025

SANS 4628-3:20XX Paints and varnishes — Evaluation of degradation of coatings — Designation of 2025-03-29
Ed 3 quantity and size of defects, and of intensity of uniform changes in appearance
Part 3: Assessment of degree of rusting. This part of ISO 4628 specifies a method
for assessing the degree of rusting of coatings by comparison with pictorial
standards

SANS 7812-1:20XX Identification cards - Identification of issuers Part 1: Numbering system . This 2025-03-29
Ed 4 document specifies a numbering system for the identification of the card issuers,
the format of the issuer identification number (IIN) and the primary account
number (PAN).
SANS 61800-3:20XX Adjustable speed electrical power drive systems Part 3: EMC requirements and 2025-03-29
Ed 3 specific test methods for PDS and machine tools. This part of IEC 61800 specifies
electromagnetic compatibility (EMC) requirements for adjustable speed power
drive systems (PDSs) and machine tools (MTs). A PDS is an AC or DC motor
drive including an electronic converter. Requirements are stated for AC and DC
PDSs and MTs with input and/or output voltages (line-to-line voltage), up to 35 kV
AC RMS. This document applies to equipment of all power ratings.
SANS 61260-1:20XX Electroacoustics — Octave-band and fractional-octave-band filters 2025-03-29
Ed 1 Part 3: Specifications. This part of the IEC 61260 series specifies
performance requirements for analogue, sampled-data, and digital
implementations of band-pass filters. The extent of the pass-band region of
a filter's relative attenuation characteristic is a constant percentage of the
exact mid- band frequency for all filters of a given bandwidth. An instrument
conforming to the requirements of this standard may contain any number of
contiguous band-pass filters covering any desired frequency range
SANS 61260-2:20XX Electroacoustics — Octave-band and fractional-octave-band filters 2025-03-29
Ed 1 Part 3: Pattern-evaluation tests. This part of IEC 61260 provides details of
the tests necessary to verify conformance to all mandatory specifications
given in IEC 61260-1:2014 for octave-band and fractional-octave- band
filters
SANS 61960-4:20XX Secondary cells and batteries containing alkaline or other non-acid 2025-03-29
Ed 1 electrolytes — Secondary lithium cells and batteries for portable
applications Part 4: Coin secondary lithium cells, and batteries made from
them. This part of IEC 61960 specifies performance tests, designations,
markings, dimensions and other requirements for coin secondary lithium
cells and batteries for portable applications and backup power supply such
as memory backup applications
SANS 61010-2- Safety requirements for electrical equipment for measurement, control, and 2025-03-29
020:20XX laboratory use Part 2-020: Particular requirements for laboratory
Ed 3 centrifuges. Replacement: This Part 2 is applicable to electrically powered
LABORATORY CENTRIFUGES.This group safety publication is primarily
intended to be used as a product safety standard for the products
mentioned in the scope, but shall also be used by technical committees in
the preparation of its publications for products similar to those mentioned in
the scope of this standard, in accordance with the principles laid down in
IEC Guide 104 and lSO/lEC Guide 51.
SANS 15288:20XX Systems and software engineering - Systems life cycle processes. This 2025-03-29
Ed 4 document establishes a common framework of process descriptions for
describing the life cycle of systems created by humans, defining a set of
processes and associated terminology from an engineering viewpoint.
These processes can be applied to systems of interest, their system
elements, and to systems of systems. Selected sets of these processes can
be applied throughout the stages of a system's life cycle. This is
accomplished through the involvement of stakeholders, with the ultimate
goal of achieving customer satisfaction
SANS 23026:20XX Pipe flan Systems and software engineering - Engineering and 2025-03-29
Ed 2 management of websites for systems, software and services information.
This document defines system engineering and management requirements
for the life cycle of websites, including strategy, design, engineering, testing
and validation, and management and sustainment for intranet and extranet
environments. This document applies to those using web technology to

This gazette is also available free online at www.gpwonline.co.za

 STAATSKOERANT, 29 Januarie 2025 No. 52012   9

present information and communications technology (ICT) information, such

as information for users of systems and services, plans and reports for
systems and software engineering projects, and documentation of policies,
plans, and procedures for IT service management. This document provides
requirements for website owners and website providers, managers
responsible for establishing guidelines for website development and
operations, website engineers, designers, developers, and operations and
maintenance staff, who can be external or internal to the website owner's
organization. It applies to websites for public access and for limited access,
such as for users, customers, and subscribers seeking information on IT
systems, products and services.
SANS 60695-11- Fire hazard testing. Part 11-10: Test flames — 50 W horizontal and 2025-03-29
10:20XX vertical flame test methods. This part of IEC 60695 specifies small-scale
Ed 2 laboratory test procedures intended to compare the burning behaviour of
different materials used in electrotechnical products when vertically or
horizontally oriented test bar specimens are exposed to a small flame
ignition source with a nominal thermal power of 50 W. These test methods
determine either the linear burning rate or the self-extinguishing properties
of materials.
SANS 61010-031:20XX Safety requirements for electrical equipment for measurement, control, and 2025-03-29
Ed 2 laboratory use Part 031: Safety requirements for hand-held and hand-
manipulated probe assemblies for electrical test and measurement. This
part of IEC 61010 specifies safety requirements for hand-held and hand-
manipulated probe assemblies for electrical test and measurement, and
their related accessories. These probe assemblies are for non-contact or
direct electrical connection between a part and electrical test and
measurement equipment. They can be fixed to the equipment or be
detachable accessories for the equipment.
SANS 4628-1:20XX Paints and varnishes — Evaluation of degradation of coatings — 2025-03-29
Ed 3 Designation of quantity and size of defects, and of intensity of uniform
changes in appearance Part 1: General introduction and designation
system. This part of ISO 4628 defines a system for designating the quantity
and size of defects and the intensity of changes in appearance of coatings
and outlines the general principles of the system used throughout ISO
4628. This system is intended to be used, in particular, for defects caused
by ageing and weathering, and for uniform changes, for example yellowing.
SANS 2071:20XX Disinfectants and detergent-disinfectants for use in healthcare 2025-03-29
Ed 1 environments. This standard specifies the requirements for disinfectants
and detergent-disinfectants for use in healthcare environments.
SANS 61800-7- Adjustable speed electrical power drive systems.Part 7-204: Generic 2025-03-29
204:20XX interface and use of profiles for power drive systems — Profile type 4
Ed 2 specification.This part of IEC 61800 specifies profile type 4 for power drive
systems (PDS). Profile type 4 can be mapped onto different communication
network technologies.
SANS 61800-7- Adjustable speed electrical power drive systems.Part 7-202: Generic 2025-03-29
202:20XX interface and use of profiles for power drive systems — Profile type 2
Ed 2 specification. This part of IEC 61800 specifies profile type 2 (CIP Motion™)
for Power Drive Systems (PDS). Profile type 2 can be mapped onto
different communication network technologies.
SANS 24773-4:20XX Software and systems engineering — Certification of software and systems 2025-03-29
Ed 1 engineering professionals Part 4: Software engineering. This document
elaborates requirements and recommendations for certifications schemes
based on ISO/IEC 24773-1, which are specific to the domain of software
engineering.
SATR 41030:20XX Facility management - Existing performance management in facility 2025-03-29
Ed 1 management organizations - State of the industry. This document provides
a robust understanding of existing performance measures in facility
management (FM) organizations and the needs of both:
SANS 60332-3-23:20XX Tests on electric and optical fibre cables under fire conditions.Part 3-23: 2025-03-29
Ed 2 Test for vertical flame spread of vertically-mounted bunched wires or cables
— Category B. This part of IEC 60332 covers category B for methods of
test for the assessment of vertical flame spread of vertically-mounted

This gazette is also available free online at www.gpwonline.co.za

10  No. 52012 GOVERNMENT GAZETTE, 29 January 2025

bunched wires or cables, electrical or optical, under defined conditions

SANS 38503:20XX Information technology — Governance of IT — Assessment of the 2025-03-29
Ed 1 governance of IT. This document provides guidance on the assessment of
governance of information technology (IT) based on the principles,
definitions and model for the governance of IT outlined in ISO/IEC 38500
and ISO/IEC TR 38502 and the implementation considerations outlined in
ISO/IEC TS 38501
SANS 60335-2-14:20XX Household and similar electrical appliances — Part 2-14: Particular 2025-03-29
Ed 5 requirements for kitchen machines. This part of IEC 60335 deals with the
safety of electric kitchen machines for household and similar purposes, their
rated voltage being not more than 250 V.
SANS 62841-2-6:20XX Electric motor-operated hand-held tools, transportable tools and lawn and 2025-03-29
Ed 1 garden machinery — Safety Part 2-6: Particular requirements for hand-held
hammers. This part of IEC 62841 applies to hand-held hammers.
Tools covered by this document include percussion hammers and rotary
hammers, including rotary hammers with the capability to rotate only with
the percussion system disengaged (drill only mode).
SANS 60669-2-3:20XX Switches for household and similar fixed electrical installations. Part 2-3 2025-02-28
Ed 3 :Particular requirements —Time-delay switches (TDS). This part of IEC
60669 applies to time-delay switches (hereinafter referred to as TDS) with a
rated voltage not exceeding 440 V AC and a rated current not exceeding 63
A, intended for household and similar fixed electrical installations, either
indoors or outdoors, operated by hand and/or by remote control. For the
control circuit, the rated control voltage does not exceed 440 V AC or 220 V
DC.
SANS 61439-3:20XX Low-voltage switchgear and controlgear Assemblies. Part 3: Distribution 2025-02-28
Ed 2 boards intended to be operated by ordinary persons (DBO). This part of IEC
61439 defines the specific requirements for distribution boards intended to
be operated by ordinary persons (abbreviated DBO throughout this
document, see 3.1.101) as follows
SANS 61439-4:20XX Low-voltage switchgear and controlgear Assemblies. Part 4: Particular 2025-02-28
Ed 2 requirements for assemblies for construction sites (ACS). This document
defines the specific requirements of ACS as follows: assemblies for which
the rated voltage does not exceed 1 000 V in case of AC or 1 500 V in case
of DC;

SCHEDULE A.1: AMENDMENT OF EXISTING STANDARDS

The following draft amendments are hereby issued for public comments in compliance with the norm for the development
of the South African National Standards in terms of section 23(2)(a) (ii) of the Standards Act.

Draft Standard
Title Scope of amendment Closing
No. Date
and Edition
SANS 1439:20XX Automotive upholstery fabrics Amended to update reference standards, and 2025-03-29
Ed 2.5 to delete the annex on notes to purchasers.

SANS 5965:20XX Non-fibrous material content of textiles Amended to update referenced standards, 2025-03-29
Ed 2.1 (alkali hydrolysis method) and to delete the annex on notes to users.

SANS 1177:20XX Terry jacquard articles This standard covers the requirements for 2025-03-29
Ed 2.1 woven terry jacquard face cloths, towels,
and bath mats suitable for domestic and
institutional use
SANS 1316:20XX Cotton cellular blankets Amended to update normative references, 2025-03-29
Ed 2.2 and to delete the annex on notes to
purchasers
SANS 5208:20XX Determination of lead content in different Amended to update the title and the clauses 2025-03-29
Ed 3.03 water matrices using air-acetylene flame on principle, reagents, and on procedure.
atomic adsorption spectroscopy (FAAS)

8
This gazette is also available free online at www.gpwonline.co.za
 STAATSKOERANT, 29 Januarie 2025 No. 52012   11

SANS 10371:20XX Terms and definitions for clothing Amended to update the referenced standards 2025-03-29
Ed 1.2

SANS 1245:20XX Non-woven cleaning wipes Amended to update referenced standards and 2025-03-29
Ed 1.1 to delete the annex on notes to purchasers

SANS 61084- Cable trunking systems and cable ducting Amended to update referenced standards, to 2025-03-29
1:20XX systems for electrical installations Part 1: modify requirements for general conditions
Ed 2.1 General requirements for tests, mechanical properties, thermal
properties, electromagnetic compatibility,
and an annex for CTS/CDS IK code
SANS 164-6:20XX Plug and socket-outlet systems for Amended to update the dimensions on 2025-02-28
Ed 1.7 household and similar purposes for use in standard sheet 6-1.
South Africa Part 6: Two-pole (Class II):
16 A 250 V a.c. system
SANS 164-1:20XX Plug and socket-outlet systems for Amended to update the foreword, the 2025-02-28
Ed 5.7 household and similar purposes for use in requirements, and to add the annex on gauge
South Africa Part 1: Two-pole and earth, for verifying the encroachment area
16 A 250 V a.c. system

SANS 164-0:20XX Plug and socket-outlet systems for Amended to update the foreword, referenced 2025-02-28
Ed 1.10 household and similar purposes for use in standard, and the requirements on
South Africa Part 0: General requirements dimensions

SANS 6171:20XX Determination of Nickel in different water Amended to update to update the title of the 2025-03-29
Ed 1.3 samples using air -acetylene flame and standard, and to make editorial changes on
direct atomic adsorption spectroscopy principles ,reagent, and on procedure
FAAS

SANS 1661:20XX Cord extension sets and cable reels Amended to update the requirements for 2025-03-29
Ed 4.2 cable reels

SANS 185:20XX Immersion-type heating units for electrical Amended to delete the annex on notes to 2025-03-29
Ed 3.4 appliances purchasers

SANS 186:20XX Energy regulators for electric heating unit Amended to delete the annex on notes to 2025-02-28
Ed 3.2 purchasers

SANS 1470- Sound power labelling Part 1: Amended to update referenced standards 2025-03-29
1:20XX Compressors
Ed 1.3
SANS 1470- Sound power labelling Part 3: Rotating Amened to update referenced standards 2025-03-29
3:20XX electrical machinery
Ed 2.1

SANS 1470- Sound power labelling Part 4: Pneumatic Amended to update referenced standards. 2025-03-29
4:20XX equipmen
Ed 2.1
SANS 62271- High-voltage switchgear and controlgear Amended to update referenced standards, 2025-03-29
200:20XX Part 200: AC metal-enclosed switchgear definitions, design and construction, type
Ed 3.1 and controlgear for rated voltages above 1 tests, routine tests and guide to the selection
kV and up to and including 52 kV of switchgear and controlgear, and to
introduce an annex on pressure coordination
chart for gas-filled compartments
SANS 61084-2- Cable trunking systems and cable ducting Amended to update the referenced standards, 2025-03-29
4:20XX systems for electrical installations Part 2- to modify requirements for general
Ed 2.1 4: Particular requirements — Service conditions for tests, mechanical properties,
poles and service posts fire hazard and an annex for Routine test for
the socket outlets wiring of pre-wired
service poles and service posts (correct

This gazette is also available free online at www.gpwonline.co.za

12  No. 52012 GOVERNMENT GAZETTE, 29 January 2025

polarity and protection against electric

shock)

SANS 61084-2- Cable trunking systems and cable ducting Amended to update referenced standards and 2025-03-29
1:20XX systems for electrical installations Part 2- mechanical properties
Ed 2.1 1:Particular requirements— Cable
trunking systems and cable ducting
systems intended for mounting on walls
and ceilings
SANS 1619:20XX Small power distribution units (ready- Amended to update a reference standard 2025-02-28
Ed 2.6 boards) for single-phase 230 V service
connections
SANS 60335-2-15 household and similar electrical Amended to update reference standards, and 2025-03-29
Ed 4.2 appliances - Safety Part 2-15: Particular to delete the annex on notes to purchasers.
requirements for appliances for heating
liquids

SANS 1245:20XX Non-woven cleaning wipes Amended to update reference standards, and 2025-03-29
Ed 1.1 to delete the annex on notes to purchasers.

SANS 61084-2- Cable trunking systems and cable ducting Amended to update a referenced standard, to 2025-02-28
3:20XX systems for electrical installations modify requirements for mechanical
Ed 1.1 Part 2-3: Particular requirements— properties, electromagnetic compatibility,
Slotted cable trunking systems intended for and an annex for CTS/CDS IK code
installation in cabinets
SANS 5209:20XX Determination of Manganese content in Amended to update to update the title of the 2025-03-29
Ed 3.3 different water matrices using air- standard, and the clauses on principles
acetylene flame atomic adsorption ,reagent, and sample analysis
spectroscopy (FAAS)
SANS 6048:20XX Amended to update the title of the 2025-03-29
Water — Determination of chemical
Ed 2.03 document, and clauses on apparatus and
oxygen demand in water samples using
procedure.
open reflux titrimetric method
SANS 5214:20XX Determination of Zinc content in different Amended to update to update the title of the 2025-03-29
Ed 3.3 water matrices using air-acetylene flame standard and addition of technical
and direct atomic adsorption spectroscopy information on some clauses
(FAAS)
SANS 5214:20XX Determination of Zinc content in different Amended to update to update the title of the 2025-03-29
Ed 3.3 water matrices using air-acetylene flame standard and addition of technical
and direct atomic adsorption spectroscopy information on some clauses
(FAAS)
SANS 5207:20XX Determination of iron content in different Amended to update to update the title of the 2025-03-29
Ed 3.3 water matrices using air-acetylene flame standard, and the clauses on principles
atomicadsorption spectroscopy (FAAS) ,reagent, and on procedure

SCHEDULE B.4: REINSTATEMENT OF WITHDRAWN STANDARD

Copies of the standards mentioned in this notice can be obtained from the Head Office of the South African Bureau of
Standards at 1 Dr Lategan Road, Groenkloof, Private Bag X191, Pretoria 0001.
______________________________________________________________________________________

10free online at www.gpwonline.co.za

This gazette is also available