TA16
series
Product Segments TiMOTION's TA16 series linear actuator is similar to the TA2 linear actuator,
but is specifically designed for low-noise applications where a compact linear
• Care Motion actuator is needed. It is available with optional IP66 protection and Hall sensors
• Comfort Motion for position feedback. Certificates for the TA16 include IEC60601-1, ES60601-1,
IEC60601-1-2, UL962, and EMC.
• Ergo Motion
General Features
• Industrial Motion
Max. load 4,500N (push) ; 2,500N (pull)
Max. speed at max. load 4.9mm/s
Max. speed at no load 56.5mm/s
Retracted length ≥ Stroke + 112mm
IP rating IP66M
Certificate IEC60601-1, ES60601-1, IEC60601-1-2,
UL962, EMC
Stroke 20~600mm
Output signals Mechanical Pot., NPN Hall sensors,
PNP Hall sensors
Options Motor brake
Voltage 12/24/36/48V DC; 12/24/48V DC (PTC)
Color Silver
Operational temperature range +5°C~+45°C
at full performance
With very low noise, small size for easy installation
Suitable for patient hoist application
1
series
TA16 Drawing
Dimensions
without Output Signal
or with Hall Sensors
(mm)
139.4
33.3
21.5
ø20
43
15
35
85
20.7
21.5
Retracted Length 43
Dimensions with POT
(mm)
175.4 13.2
6
ø20
12.2
R22.5
ø10 R11
85
20.7
10.7
Retracted Length ø10 43 R10
2
series
TA16 Load and Speed
CODE Load (N) Self Locking Typical Current (A) Typical Speed (mm/s)
Force (N)
Push Pull No Load With Load No Load With Load
32V DC 24V DC 32V DC 24V DC
Motor Speed (3800RPM, Duty Cycle 10%)
A 2500 2500 2500 1.7 2.4 5.2 3.0
B 2000 2000 2000 1.7 2.4 8.3 4.7
C 1500 1500 1500 1.7 2.2 10.8 7.0
D 1000 1000 1000 1.7 2.4 17.1 10.0
E 500 500 500 1.7 2.8 56.5 28.0
Motor Speed (5200RPM, Duty Cycle 10%)
G 3500 2500 3500 2.0 4.7 11.0 6.2
J 2000 2000 2000 2.0 3.7 15.8 9.5
K 1500 1500 1500 2.0 3.7 21.5 14.2
L 4500 2500 4500 2.0 5.0 9.5 4.9
Note
1 #G_When pull load > 2500N, please discuss with engineer.
2 Please refer to the approved drawing for the final authentic value.
3 This self-locking force level is reached only when a short circuit is applied on the terminals of the motor. All the TiMOTION control
boxes have this feature built-in. The self-locking force is a minimum value and can be actually higher.
4 T he current & speed in table are tested with 24V DC motor. With a 12V DC motor, the current is approximately twice the current
measured in 24V DC. With a 36V DC motor, the current is approximately two-thirds the current measured in 24V DC. With a 48V
DC motor, the current is approximately half the current measured in 24V DC. Speed will be similar for all the voltages.
5 The current & speed in table is tested when the actuator is extending under push load
6 The current & speed in table and diagram are tested with TiMOTION control boxes, and there will be around 10% tolerance
depending on different models of the control box. (Under no load condition, the voltage is around 32V DC. At rated load, the voltage
output will be around 24V DC)
7 Without load, noise level ≤ 56dBA (by TiMOTION test standard, ambient noise level ≤ 36dBA).
8 Standard stroke: Please refer to the table below.
CODE Load (N) Min Stroke (mm) Max Stroke (mm)
E ≤ 500 38 600
D ≤ 1000 20 600
C, K ≤ 1500 20 500
B, J ≤ 2000 20 450
A ≤ 2500 20 400
G ≤ 3500 20 300
L ≤ 4500 20 300
3
series
TA16 Performance Data (24V DC Motor)
Motor Speed (3800RPM, Duty Cycle 10%)
Speed vs. Load
60.0
50.0
40.0
Speed (mm/s)
30.0
E
20.0
10.0 D
C
B
A
0.0
0 1000 2000 3000 4000 5000
Load (N)
Current vs. Load
6.0
5.0
4.0
Current (A)
3.0 E
D
B A
C
2.0
1.0
0.0
0 1000 2000 3000 4000 5000
Load (N)
4
series
TA16 Performance Data (24V DC Motor)
Motor Speed (5200RPM, Duty Cycle 10%)
Speed vs. Load
60.0
50.0
40.0
Speed (mm/s)
30.0
20.0
10.0 J
G
L
0.0
0 1000 2000 3000 4000 5000
Load (N)
Current vs. Load
6.0
L
5.0
G
4.0
K J
Current (A)
3.0
2.0
1.0
0.0
0 1000 2000 3000 4000 5000
Load (N)
5
TA16 Ordering Key
TA16 Version: 20240415-R
Voltage 1 = 12V DC 3 = 36V DC 5 = 24V DC, PTC 8 = 48V DC, PTC
2 = 24V DC 4 = 48V DC 6 = 12V DC, PTC
Load and Speed See page 3
Stroke (mm) See page 3
Retracted Length See page 7
(mm)
Rear Attachment 1 = Aluminum, U clevis, width 6.0, depth 12.2, hole 6.4, one piece casting with gearbox
(mm) 2 = Aluminum, U clevis, width 6.0, depth 12.2, hole 8.0, one piece casting with gearbox
See page 8 3 = Aluminum, U clevis, width 6.0, depth 12.2, hole 10.0, one piece casting with gearbox
B = Aluminum, U clevis, width 6.0, depth 12.2, hole 10.2, one piece casting with gearbox, with plastic T-bushing
(black), for weather resistant application
Front Attachment 1 = Aluminum, slotless, hole 6.4 6 = Aluminum, U clevis, width 6.0, depth 13.0, hole 10.0
(mm) 2 = Aluminum, slotless, hole 8.0 B = Aluminum, slotless, hole 10.2, with plastic T-bushing
See page 8 3 = Aluminum, slotless, hole 10.0 (black), for weather resistant application
4 = Aluminum, U clevis, width 6.0, depth 13.0, hole 6.4 C = Steel, U clevis, width 6.0, depth 13.0, hole 10.2,
with plastic T-bushing (black), for weather resistant
5 = Aluminum, U clevis, width 6.0, depth 13.0, hole 8.0 application
Direction of 1 = 90° 2 = 0°
Rear Attachment
(Counterclockwise)
See page 9
IP Rating 1 = Without 3 = IP66 6 = IP66M
2 = IP54 5 = IP66W
Function of 1 = Two micro switches cut off the actuator at end of stroke
Limit Switches 2 = Two micro switches cut off the actuator at end of stroke + third one in between sends signal
See page 9 3 = Two micro switches send signal at end of stroke
4 = Two micro switches send signal at end of stroke + third one in middle sends signal
Special Function of 0 = Without (Standard) 2 = Standard push only
Spindle Set 1 = Safety nut 3 = Standard push only + safety nut
Output Signal 0 = Without 4 = Hall sensor*1 N = NPN Hall sensor*2
1 = Mechanical pot. 5 = Hall sensor*2 P = PNP Hall sensor*2
Connector 1 = DIN 6P, 90° plug C = Y cable (For direct cut system, water proof, anti pull) G = Audio plug
See page 9-10 2 = Tinned leads E = Molex 8P, plug
4 = Big 01P, plug F = DIN 6P, 180° plug
Cable Length (mm) 0 = Straight, 100 3 = Straight, 1000 6 = Straight, 2000 B~H = For direct cut system
1 = Straight, 500 4 = Straight, 1250 7 = Curly, 200 See page 9
2 = Straight, 750 5 = Straight, 1500 8 = Curly, 400
Brake 0 = Without 1 = Motor brake
Load Type T = Push P = Pull
Color 0 = Silver grey
3 = Glittering black, for weather resistant application
6
TA16 Ordering Key Appendix
Retracted Length (mm)
1. Calculate A+B+C+D+E = Y
2. Retracted length needs to ≥ Stroke + Y
A. Rear / Front Attach. C. Load V.S. Spindle Functions
Front Rear Attach. Spindle Load & Speed Type
Attach. Functions
1, 2, 3, B A, B, C, D, E, J, K G, L
1, 2, 3 +112 0 - -
B +115 1 +10 +5
4, 5, 6, C +122 2 +2 +2
3 +12 +7
B. Load V.S. Stroke
Stroke (mm) Load & Speed Type D. Output Signals
A, B, C, D, E, J, K G, L 0, 4, 5, N, P -
20~150 - +13 1 +36
151~200 +8 +21
201~250 +8 +21
251~300 +13 +26
301~350 +13 +26
351~400 +18 +31
401~450 +23 +36
451~500 +28 +41
501~550 +33 +46
551~600 +38 +51
7
TA16 Ordering Key Appendix
Rear Attachment (mm)
1 = Aluminum, U clevis, width 6.0, 2 = Aluminum, U clevis, width 6.0, 3 = Aluminum, U clevis, width 6.0, B = Aluminum, U clevis, width 6.0,
depth 12.2, hole 6.4, one piece depth 12.2, hole 8.0, one piece depth 12.2, hole 10.0, one piece depth 12.2, hole 10.2, one piece
casting with gearbox casting with gearbox casting with gearbox casting with gearbox, with
plastic T-bushing (black), for
weather resistant application
R11
ø6.4 ø8 ø10
35.8
35.8
35.8
35.8
R11 R11 R11
ø10.2
26.2
21
21
21
21
6
6
6
12.2 12.2 12.2 12.2
Front Attachment (mm)
1 = Aluminum, slotless, hole 6.4 2 = Aluminum, slotless, hole 8.0 3 = Aluminum, slotless, hole 10.0 4 = Aluminum, U clevis, width 6.0,
depth 13.0, hole 6.4
ø6.4 ø8 ø10 ø6.4
9 9 9 13
6.1
ø20
ø20
ø20
ø20
5 = Aluminum, U clevis, width 6.0, 6 = Aluminum, U clevis, width 6.0, B = Aluminum, slotless, hole 10.2, C = Steel, U clevis, width 6.0, depth
depth 13.0, hole 8.0 depth 13.0, hole 10.0 with plastic T-bushing (black), for 13.0, hole 10.2, with plastic
weather resistant application T-bushing (black), for weather
resistant application
ø8 ø10 ø10.2 ø10.2
11 13
13 13
6.1
6.1
26.2
∅21
∅25.2
6.1
∅20
ø20
ø20
8
TA16 Ordering Key Appendix
Direction of Rear Attachment (Counterclockwise)
1 = 90° 2 = 0°
Hole
Hole
º 0º
90
Function of Limit Switches
Wire Definitions
CODE Pin
1 (Green) 2 (Red) 3 (White) 4 (Black) 5 (Yellow) 6 (Blue)
1 extend (VDC+) N/A N/A N/A retract (VDC+) N/A
2 extend (VDC+) N/A middle switch pin B middle switch pin A retract (VDC+) N/A
3 extend (VDC+) common upper limit switch N/A retract (VDC+) lower limit switch
4 extend (VDC+) common upper limit switch medium limit switch retract (VDC+) lower limit switch
Connector
1 = DIN 6P, 90° plug 2 = Tinned leads 4 = Big 01P, plug
C = Y cable (For direct cut system, water proof, anti pull)
L3 Cable Length for Direct Cut System (mm)
CODE L1 L2 L3
B 100 100 100
L2 L1
C 100 1000 400
D 100 2700 500
E 1000 100 100
F 100 600 1000
G 1500 1000 1000
H 100 100 1200
9
TA16 Ordering Key Appendix
Connector
E = Molex 8P, plug F = DIN 6P, 180° plug G = Audio plug
Terms of Use
The user is responsible for determining the suitability of TiMOTION products for a specific application.
TiMOTION products are subject to change without prior notice.
10
