EIKON ARKE' IDEA PLANA

20594.0 19594.0-19594 16494 14594-14594.0

Connected roller shutter control device

20594.0-19594.0-14594.0: to be completed with two interchangeable half-button caps: 1 2) Where present now set the total slat rotation time. Press button , the roller shutter begins
module. to close and the LED flashes amber; when the roller shutter is closed, the LED remains lit in
19594-16494-14594: complete with buttons. amber permanently. Briefly press button P to increase by he slat rotation time by 200 ms
each time, while briefly pressing push button P will decrease it by 200 ms. Each press of the
The device is equipped with an output with 2 one-position stable relays with interlocked opera- buttons will turn the amber LED off and back on again and will move the slats.
tion, in other words with mutually exclusive activation of the relays with a minimum interlocking 3) Simultaneously press buttons  and  to save the rotation time set; the LED flashes amber
time. In the event of a mains power supply failure, the relays both remain open. quickly three times to confirm the setting.
The front buttons of the device only control the on-board roller shutter actuator:
N.B. If at the beginning of the slat handling time configuration the button is not pressed shortly
- Short press: if the roller shutter is not moving, the slat rotates; if the roller shutter is moving,
and the confirmation is given immediately by pressing both buttons at the same time, the slats
it stops.
will be excluded from operation. So in practice, when the roller shutter is in motion, pressing a
- Long press: the upper button raises the roller shutter while the lower button lowers it.
button briefly will stop it whereas if the roller shutter is not in motion pressing the button briefly
- Double pressing of either of the two buttons: recalling of favourite position (this is saved via the
will not give rise to any movement.
VIEW Wireless App).
N.B. When the voltage returns after a power outage, the roller shutter remains at a standstill.
TWO OPERATING MODES (ALTERNATIVE) Summary of Zigbee technology mode signalling.
• During normal operation:
or
LED Meaning
Download the View Wireless App from the stores onto the tablet/smartphone you On
(amber for Eikon, blue for Arké, green for Idea and Roller shutter in motion
will be using for configuration. Plana)

When the device is powered for the first configuration, we recommend you search for any Off Roller shutter at a standstill
new firmware and perform the update.
• In the configuration phase:
Depending on the mode you select, you will need:
LED Meaning
Flashing white
Zigbee mode active pending voice assistant
Gateway (for max 5 min.)
art. 20597-19597-16497-14597
Flashing blue
Pending receipt of a fw update
(for max 2 min.)
Zigbee Gateway
View App (Amazon Echo Plus, Echo Show or Echo Device associated with the smartphone via
Studio) Blue permanently lit
Bluetooth
for management via smartphone/tablet Alexa App
Flashing green during the time configuration Roller shutter opening
Amazon Alexa, Google Assistant, Siri and
Homekit voice assistants for possible Pending pressure on the  button after
Green permanently lit during configuration
voice operation complete closure
Amber permanently lit Start slat rotation time configuration
CONFIGURATION IN
1. Create your Installer account on MyVimar (on-line). Amber on while the button is pressed Increase or decrease slat rotation time
2. Wire all the devices in the system (2-way switches, actuators, thermostats, gateway, etc.). Flashing amber during the time configu-
3. Start the View Wireless App and log in with the credentials you just created. Roller shutter closing
ration
4. Create the system and the environments.
5. Associate all the devices with the environments, except for the gateway (which should be Confirm up and down time configuration
Flashing green 3 times
associated last). mode
To associate the roller shutter control device: Flashing amber 3 times Confirm slat rotation time configuration
• Select “Add” ( ), choose the environment to place it and give it a name
• Select ; activate the Bluetooth connection on your tablet/smartphone and approach Device correctly associated with the voice
Flashing green quickly 3 times
the device assistant
• Simultaneously press buttons  and  and set the desired function On
Roller shutter in motion during normal
6. For every device, set the function, the parameters and any accessory devices (wired or radio (amber for Eikon, blue for Arké, green for
operation
control and related function). Idea and Plana)
7. Transfer the configuration of the devices to the gateway and connect it to the Wi-Fi network.
8. Transfer the system to the Administrator user (who must have created his/her profile on
CONTROLLABLE LOADS.
MyVimar).
For details please refer to the View Wireless App manual you can download from www. Maximum loads Roller shutter motor
[Link]  DOWNLOAD  View Wireless MOBILE  App 100 V~ 2 A cos ø 0.6
240 V~ 2 A cos ø 0.6
CONFIGURATION IN
Follow the procedure above from points 1 to 3.
Associate the device directly with Amazon Echo Plus, Echo Show or Echo Studio.
RESETTING THE RELAY MODULE.
The reset restores the factory settings. Within the first 5 minutes from powering, simultaneously
1) Simultaneously press the buttons on the device until the LED flashes and download the Zigbee
software using the View Wireless App (see the View Wireless App manual). press the  and  buttons for 30 s until the white LED flashes.
To update the software on the device, the procedure is the same.
2) After conversion to Zigbee technology (or the software update), the device automatically goes INSTALLATION RULES.
into pairing mode so that it can be recognised by the Amazon device within 5 minutes. If the • Installation must be carried out by qualified persons in compliance with the current regula-
device is not in pairing mode, cut off the power supply and restore it after a few seconds. tions regarding the installation of electrical equipment in the country where the products are
3) Associate the device with Amazon Echo Plus, Echo Show or Echo Studio according to the installed.
procedure envisaged by the voice assistant (see the Amazon documentation). • The device must be completed with interchangeable buttons and installed in flush mounting
Set the parameters of the roller shutter control device. boxes or surface mounting boxes with Eikon, Arkè and Plana mounting frames and cover
1) Within the first 5 minutes after the device has been powered (already associated with Amazon plates.
Alexa), simultaneously press the buttons for 15 s so you can set the activation time (the LED • The relay output power circuit must be protected against overloads by installing a device, fuse
flashes green during the roller shutter closing, which will take 3 minutes, or until button  is or automatic 1-way switch, with a rated current not exceeding 10 A.
pressed). The LED is permanently lit green and within a timeout of 2 minutes, press button  • Installation must be carried out with the system switched off. Install the buttons onto the roller
for a prolonged time to raise the roller shutter. During the raising process the LED flashes green; shutter control device before powering up the system.
briefly press button  to stop it. The time that passes between the long press and the short
press of button  is the raising/lowering operating time that will be saved by the device (the
LED lights up amber).

Viale Vicenza 14
36063 Marostica VI - Italy
20594.0 02 2110 [Link]
EIKON ARKE' IDEA PLANA
20594.0 19594.0-19594 16494 14594-14594.0
Connected roller shutter control device

CHARACTERISTICS.
• Rated supply voltage: 100-240 V~, 50/60 Hz.
• Dissipated power: 0.55 W
• RF transmission power: < 100 mW (20 dBm)
• Frequency range: 2400-2483.5 MHz
• Terminals:
- 2 terminals (L and N) for line and neutral
- 1 terminal (P) for connection to the remote wired control (for instance art. 20008-19008-
16080-14008). The max distance between the IoT device and the push button is 50 m
with a cable with a minimum cross-section of 1.5 mm2.
- 2 terminals ( and ) for the roller shutter output
• 2 front buttons that are used both to control the load and as configuration push buttons.
• RGB LED indicating the movement of the roller shutter (which can be set from the View Wireless
App) and the configuration status (flashing blue)
• In Bluetooth technology mode, you can associate up to 2 radio devices (art. 03925) which make
it possible to control the actuator or activate a scenario.
• Operating temperature: -10 ÷ +40 °C (indoor)
• Protection degree: IP20
• Configuration from View Wireless App for Bluetooth technology system and Amazon App for
Zigbee technology.
• Controllable via View App (for Bluetooth technology) and Amazon Alexa (for Zigbee technology).

OPERATION IN Bluetooth technology MODE.

The device operates by default in Bluetooth technology mode and this standard makes it pos-
sible to:
- recall a scenario using the traditional push button connected to the device;
- associate the radio control 03925 which can be configured to control the actuator on-board
or to recall a scenario;
- control the QUID system devices.
Through the use of gateway 20597-19597-16497-14597 the functions can be managed locally
or remotely via the View App, and the control is also available via the voice assistants Amazon
Alexa, Google Assistant and Siri.
The device is also compatible with Homekit.
N.B.: From fw version 1.7.0, the device works as a repeater node for battery-operated devices
(for instance art. 03980).
Settings.
The View Wireless App can be used to set the following parameters:
- RGB LED for backlighting: colour can be selected from a default list (default: amber for Eikon,
blue for Arké and green for Plana).
- LED brightness: off, low, medium, high for roller shutter in motion (default: high) and for roller
shutter not in motion (default: off).
- Actuator: with or without slat (default: with slat).
- Roller shutter activation time (default: 180 s).
- Slat rotation time (default: 5 s).
- Favourite position saving (default: 50% roller shutter, 0% slats i.e. open).
- Scenario activation delay time (default: 0 s).
- Compatibility with QUID roller shutters (default: not active).

REGULATORY COMPLIANCE.
RED Directive. RoHS directive.
Standards EN 60669-2-1, EN 301 489-17, EN 300 328, EN 62479, EN 50581.
Vimar SpA declares that the radio equipment complies with Directive 2014/53/EU. The full text
of the EU declaration of conformity is on the product sheet available on the following website:
[Link]
REACH (EU) Regulation no. 1907/2006 – Art.33. The product may contain traces of lead.
WEEE - User information
The crossed bin symbol on the appliance or on its packaging indicates that the product at the end of its life must be collected separately
from other waste. The user must therefore hand the equipment at the end of its life cycle over to the appropriate municipal centres for the
differentiated collection of electrical and electronic waste. As an alternative to independent management, you can deliver the equipment you
want to dispose of free of charge to the distributor when purchasing a new appliance of an equivalent type. You can also deliver electronic
products to be disposed of that are smaller than 25 cm for free, with no obligation to purchase, to electronics distributors with a sales area
of at least 400 m2. Proper sorted waste collection for subsequent recycling, processing and environmentally conscious disposal of the old
equipment helps to prevent any possible negative impact on the environment and human health while promoting the practice of reusing and/
or recycling materials used in manufacture.

Apple HomeKit is a trademark of apple Inc. App Store is a service mark of Apple Inc. To control this
HomeKit-enabled accessory, iOS 9.0 or later is recommended. Controlling this HomeKit-enabled ac-
cessory automatically and away from home requires an apple TV with tvOS 10.0 or later or an iPad with
iOS 10.0 or later or a HomePod/Siri set up as a home hub.
The Apple logo, iPhone, and iPad are trademarks of Apple Inc., registered in the U.S. and other coun-
tries and regions. App Store is a service mark of Apple Inc.
Google, Google Play and Google Home are trademarks of Google LLC.
Amazon, Alexa and all related logos are trademarks of [Link], Inc. or its affiliates.

Viale Vicenza 14
36063 Marostica VI - Italy
20594.0 02 2110 [Link]
 FRONT AND BACK VIEW

Button DOWN output

UP output
Input for wired push button for scenario recalling

P
LED
L

L
6 mm
N

N
Button

CONNECTIONS

PUSH BUTTON* FOR

SCENARIO CONTROL

10mm
P
L

L
6 mm
N

20594.0 20008

N
L

* Do not use the signalling unit 00931. The push button can only be used in the case of operation in Bluetooth technology.

Viale Vicenza 14
36063 Marostica VI - Italy
20594.0 02 2110 [Link]